This video shows exactly what I needed to get my 2004 Toyota Tundra running again. My thottle body actually looked like it wasn't very dirty. It must have been much-needed cleanup that was not visible. I highly recommend this being done. It can be done completely in about a hour and shorter time if all the tools are laid out in advance. The cover is good to put parts in. Some people like to replace the screws, bolts or nuts so they don't forget where they go. Personally, I've lost them trying that, down on the motor somewhere never to be found. Thanks for the awesome information.

@2carpros

6 жыл бұрын

That's awesome! Thank you so much for watching and commenting!

Nice video, easy to understand

Thank you for the video, very straight forward and I was able to follow through on my Sequoia. But after all that the idle is so high and I don’t know if there’s any reset or calibration to do.

@2carpros

6 жыл бұрын

It should eventually self adjust. Thanks for watching!

My 02 tundra v8 throttle body is a bit more complex to remove. Good video regardless... Thank you

@giuseppe_M

3 жыл бұрын

YOU GOT THAT RIGHT

@lucebruno644

3 ай бұрын

NO KIDDING

Great video.

This is an 05 or 06 engine with the drive by wire/electronic throttle control. 2000-04 Tundras have still have a throttle cable. You also skipped showing clamping off and disconnecting the coolant hoses.

@sdelgado2187

3 жыл бұрын

Do you have a resource for a 2002 Toyota?

@dangeranger69

3 жыл бұрын

my 02 is drive by wire im pretty sure

@zekethefishgeek8690

10 ай бұрын

​@@dangeranger69yep

I’d of wiped the junk off the top outside of housing while I was in there, was that a oring seal between those two sealing surfaces or nothing at all where you unbolted that thing from ?

I know this is an old video and I'd like to thank you for it, helped me quite a bit. I do have a question though, is there supposed to be a gasket between the throttle body and the air intake? I didn't see one on mine but I noticed they sell a gasket for my 2005 Tundra with the 4.7l V8?

@giuseppe_M

3 жыл бұрын

THE CHILTONS SAYS TO DISCARD OLD GASKET AND REPLACE

Will this help with a P1126 code for the magnetic clutch malfunction?

so nice neat and makes job easier for us.. thx alott

@2carpros

7 жыл бұрын

Thank you for watching!

Thank you for the input. I was back on the road in an hour.

@2carpros

Жыл бұрын

Excellent! Thanks for watching Kevin!

I have code p1126 on my 2001 tundra 4.7 should I just clean it or replace it

I have a 2007 Toyota tundra 4.7 liter trd series and have a vibration in it like when you hit a rough spot in the road but when i give it gas it stops

is the Throttle Body Actuator in the same spot on a 2001 Toyota Sequoia?

Jeez what’s with all the trashing of this video not fully providing the exact info you want. How about be happy he posted it? If you can’t figure out a socket size let someone else work on your car and watch Mr Rodgers instead.

@2carpros

2 жыл бұрын

People want every little thing handed to them. I do it now but this video is several years old at this point and some folks just can't seem to grasp that. Thank you so much for commenting and watching.

How much is the throttle actuator pls

Will this get rid of a p1126 code?

I cleaned mine on my tundra, now it kinda shakes a bit and my RPM are at 500 did i do something wrong??? Previous to this it didn't shake

Thanks for this video. Definitely helped me out.

@2carpros

5 жыл бұрын

Thanks for watching!

@XIM2COOLX

3 жыл бұрын

@@2carpros this is not the correct years as listed

excellent, i dp have a Tundra 2001, it start on P or N, but when I do gear at D or R it turn off immediately, what could cause it get off? could you help me?

@mahtoosacks

5 жыл бұрын

I have the same issue! Did you figure it out??

@XkickXoutXtheXjamsXX

5 жыл бұрын

@@mahtoosacks try to clean your mass air flow sensor with rubbing alcohol or specific electronics cleaner, very easy you can you tube it, if that doesnt work following this video and cleaning rest of intake wouldnt hurt

@gyffjogofl7676

4 жыл бұрын

Its a wiring issue

Had to sub you!!!

@2carpros

5 жыл бұрын

Thank you so much!

Great video, but I have a question my 2000 tundra had the frame replaced, after replacement we start engine and it idles fine but when given throttle it will not rev above 1500rpms no matter the gear you are in. We replaced throttle body since with new OEM but the issue still exists. Any thoughts or guidance on where to go from here. Thank you

@2carpros

2 жыл бұрын

That is a pretty complicated question more than I can't answer here. If you like you can head over to our website www.2carpros.com and ask this question for free. One of our automotive experts will be along shortly to help you out. Thanks for watching!

@someguy3502

2 жыл бұрын

Pedal position sensor

There are 2 hoses on the bottom of the throttle body that you don't show being removed. What's the best way to take them off? I squeeze the clamps to loosen them, but the hoses seem stuck on there pretty good. I don't want to tear a hose or anything.

@kismetjerome

3 жыл бұрын

right?! seemed important enough to be explained i thought

@angelcortez9662

2 жыл бұрын

I know I'm 2 yrs late but those are coolant hoses that have a simple clamp that can be pressed to remove the hoses... plug them as soon as you pull them.

Thank you for your very helpful tutorial I really appreciate it.

Thank you for your help..... I need to do this today..

@2carpros

3 ай бұрын

You are so welcome!

Thank you for the video, i did the cleaning and after install all back, the engine is 1500 rpm all the time, i run a few miles but nothing change, is there anything else i need to do to set the rpm lower? if you can help us with that info would be great. thank you!

@2carpros

9 ай бұрын

Your IAC (idle air control) valve may need a replacement. Thanks for watching!

Bolts are 10mm

while recently I had problem with my 06 tundra, engine check light is on and the truck doent accelerated ?

@homsandwitch4488

4 жыл бұрын

Hey I have the same problem with my 01 tundra , did this fix the problem ?

@andrewcoxx500

3 жыл бұрын

the sandwitch34 dude I’m in the same position with my 01 tundra Tell me what helped you! Shits in limp mode. Fixed alternator blew main fuse jumping it backwards fixed that it now runs but in limp mode and I had same exact problem pedal goes 80% of the way no response and then catches and jumps Up to 2.3k rpms

@homsandwitch4488

3 жыл бұрын

@@andrewcoxx500 honestly man , I looked under the throttle cover , pack rats been chewing through the wires and re did the wires , runs fine now

@blaurence4123

10 ай бұрын

Having this issue on 02 sequoia.

Do I need to disconnect my battery before doing this? Also I hear you’re not suppose to move the plate?

@2carpros

4 жыл бұрын

Yeah it's a good idea. Thanks for watching!

This video is for a post July made 05 to 06 2UZFE 4.7L Tundra and Sequoia. This is the updated engine that went in the first year 2nd Gen Tundras. At least in the US. The title should be corrected to reflect that. If this an 00 to early 05 Tundra or Sequoia then it has been engines swapped with a updated engine.

Why did you not video or explain the clamping of the two hoses? WTF?

Im getting codes P0123 and P2135 and multiple misfires and i reset everything i cleared the CEL and discinnected the battery to make sure it was for sure dealing with the throttle. But no more codes popped up for the TPS sensors. But it is still running rough and feels like it's misfiring. But AGAIN those Throttle Position Sensor codes never popped back up. Could it be my TPS/Throttle body but not tripping the CEL?

@blaurence4123

10 ай бұрын

ECU? When were your valves last checked/replaced?

Would you recommend cleaning or replacing?

@2carpros

2 жыл бұрын

Clean first and if that doesn't work then replace. It doesn't cost anything to clean. Thanks for watching!

Does this method work on a 2005 sequoia?

@Gucci2times

6 жыл бұрын

Mario Camey yeah, I did this on my 2006 so I'm sure 2005 will be the same

@americanasgrandson

5 жыл бұрын

Sorry, I realize you asked this a while back. But I believe the sequoia's have the same 4.7L engine Tundra's have. So as long as it's a 4.7L, it's likely the same.

Mine is a 05 with the drive by wire I believe. I get vibrations when I put it in gear while idling but goes away in N or P. Can a dirty throttle plate cause that? Also will this procedure mess up a throttle body that’s driven by wire electronically and not cable?

@MrBrad0910

3 жыл бұрын

My question exactly. And............ No answer 😕

My electric connection plug on the side, broke off, and even after cleaning it still idles high. Is it the missing connection plug?

@2carpros

2 жыл бұрын

Yeah most likely. If it broke off you will need a new unit. Thanks for watching!

Using Ratchet Wrench of drive 3/8? also deep socket?

@2carpros

7 жыл бұрын

We used a deep well to clear the throttle body but you could probably use an extension and a normal socket and yes 3/8 drive is what we used.

@MuhammadAli-su3oo

7 жыл бұрын

Thanks so much for reply

@2carpros

7 жыл бұрын

Thank you for watching!

@MuhammadAli-su3oo

7 жыл бұрын

Your channel is very much nice.

@2carpros

7 жыл бұрын

Thank you, that is so nice of you to say!

Show the 5.7 L on 2008 is it the same ?

@2carpros

4 жыл бұрын

So the great thing about the LS series from GM is that they are fairly similar. It would look a lot like this but arranged a little different. Thanks for watching!

@1RungAtATime

4 жыл бұрын

@@2carpros I'm pretty sure John Waid was referring to the second generation Tundra that had the 5.7 liter as an engine option.

This looks nothing like my tundra throttle body area. Mine is a 2000 tundra 4.7 v8. Actuator is on passenger side

@1RungAtATime

4 жыл бұрын

The title is misleading; this video shows an 05 or 06 Tundra.

Will this fix the P1126 code on my 2000 tundra

@2carpros

2 жыл бұрын

I'd try it then clear the codes and see if it comes back. Thanks for watching!

@jonathanfranciscopadilla8553

2 жыл бұрын

Any luck luke ?

Could this be the cause of my 07 Tundra dying while driving? Usually occurs after about an hour of driving and letting up on the gas pedal.

@phslion

Жыл бұрын

Ever fix this?

@stoweman34

Жыл бұрын

@@phslion Negative. It occurs most often when I tow my boat/trailer on the freeway and get off on an exit. As soon as I release the gas pedal it dies. I have to wait several minutes sometimes for it to restart. Also, if I drive about 15 miles and then let the truck idle for over 20 min, it will die at idle. It has something to do with pulling RPMs above 3000’ish and then the truck can’t recalibrate to the lower RPMs.

@phslion

Жыл бұрын

@@stoweman34 I've just been helping someone troubleshoot a similar issue. All sources seem to indicate look at the throttle body, gas pedal position sensor, and try a idle relearn. Idle is all controlled by the ECU on these. Interesting it won't instantly restart, a part must be failing when warm. Maybe test your O2 sensors and watch fuel trim levels on a scanner.

@stoweman34

Жыл бұрын

@@phslion Advice is much appreciated👍🏼

@blaurence4123

10 ай бұрын

$900 ECU, but then I loose power after towing a empty trailer and misfires no one can fix... Just saw it may be a valve issue

Does the cover plate do anything meaningful?

Hello

@2carpros

6 жыл бұрын

Hello! Thanks for watching!

Throttle body cleaner is safer to use. The rubber shaft seals as well as plastic pieces and the electronics inside won't be harmed by proper throttle body cleaner spray, and it won't remove the coating some TBs have applied to the inside.

@2carpros

6 жыл бұрын

Nothing wrong with using either. I have used both for years and haven't really noticed a difference. Thanks for watching!

@mannys9130

6 жыл бұрын

2CarPros As I said, the formulations are different and can cause issues for the aforementioned reasons. Do not use anything other than throttle body cleaner for throttle bodies, and mass air flow sensor cleaner for MAFs.

@2carpros

6 жыл бұрын

As I said, I have been using both for years. Haven't seen a difference. Using carb spray on a throttle body is totally fine.

@mannys9130

6 жыл бұрын

2CarPros FoMoCo specifically stipulates TBC be used due to Teflon coated butterfly valves. Anecdotal evidence is not sufficient. Guys will tell you they use straight tap water in their cooling system for years and have no problems. They'll tell you they run no thermostat and have no issues. That does NOT make it ok or safe to do. The manufacturer knows their components best.

What about the idle relearn. After cleaning the throttle body now it really idles too fast. You should have showed the second part how to relearn the idle.

@johncody3653

6 жыл бұрын

Ted Fox ...did you find the idle reset procedure

This does not show the early tundra throttle body.

Hi, thank you for posted the vid/ But throttle actuator will helps to save gas mileage yeah ?

@2carpros

7 жыл бұрын

Maybe a little bit yeah. Thank you so much for watching!

@greenautotech

5 жыл бұрын

The only way to TRULY save on fuel costs with any throttle body is with The Gadgetman Groove! This tech has helped over 10,000 just like you, now in 44 countries. (Facebook: Gadgetman Michael) it's a simple adjustment i can do to increase mileage by atleast 25%. These engines usually see between 40-70%, power is increased, and emissions lowered so much you can't smell you're exhaust anymore. It works everytime. Contact me to learn more. Id love to help. Senior Trainer of The Gadgetman Groove Michael Lee 763-220-9712

You guys forgot to show the removal of fuel lines.. big part you left out -

@MrRobsm88

4 жыл бұрын

Richard Acosta there are no fuel lines removed during this job.

@richardacosta5127

4 жыл бұрын

robert smith - I spoke too soon.. I disconnected two lines that weren’t shown on the video and figured out coolant flows through them. Thanks for posting the video though. Helped me out and got it done. Runs better now when I use the AC. My truck use to die out.. all fixed now 🍻

That's a metal cover piece on my 2002 !

Why use carb cleaner on a throttle body? Not the smartest idea. Lol throttle body cleaner is safer for the throttle plate coating and any sensors. Good video

@2carpros

3 жыл бұрын

I have been using carb spray on throttle bodies for 10 years and have had zero issues. My father has been doing that since throttle bodies came out with zero issues. Thanks for watching!

@captaininsano2777

3 жыл бұрын

@@2carpros again, not the smartest idea. Lol professional mechanics everywhere will tell you the same. SMH

doesnt cover 2000.

So we just going to ignore him using crome plated sockets on an air tool?

@2carpros

4 жыл бұрын

Sure are, thanks for watching!

@theautomaninflorida

2 жыл бұрын

Does not matter. Nothing is super tight here.