Three Ways To Taper The End Of Wire Before You Draw It Down
Фильм және анимация
Three ways you can use to taper the end of wire before you draw it down.
THE EQUIPMENT I USE TO VLOG
Sony RX100 V : tinyurl.com/ybbqxg8j
Canon 80D, Body; amzn.to/2S9U3A9
Canon Lens 10-18mm; tinyurl.com/gncnrwz
Tripod for Canon; tinyurl.com/hdhuz6z
Memory Cards; tinyurl.com/z8mhuk4
Card Reader; tinyurl.com/z97tccx
Microphone, Cheap; tinyurl.com/hbxtthg
Microphone; tinyurl.com/zpjpoeq
Canon G7X Camera; tinyurl.com/jkvu4b4
Tripod for G7X; tinyurl.com/z27m9aj
Mini Tripod; tinyurl.com/he93omu
Mavic Drone; tinyurl.com/jfh9da4
360 Camera; tinyurl.com/jbmrugq
Andrew shows you many hints and tips that he has gained from his experience as a professional goldsmith.
Andrew Berry, a professional jeweller for 30 years, is the training director of www.AtTheBench.com, an award winning on line jewellery training website.
Пікірлер: 27
I have a rolling mill. Never thought to use it to make the taper. You saved a hours of pounding and filing. Thanks.
@jonathantravelstead
Жыл бұрын
Ditto. Thanks!
Merry Christmas Andrew. Thanks for all the videos
As always good, concise content. Merry Christmas and enjoy your family. 🎄
Thank you for the tips. Merry Christmas Andrew! 🎄
Another great vlog Andrew, Merry Christmas to you and your family. Stevie
good show thanks
THANK YOU! I never thought I would find something with that keywords! that's exactly what I was trying to find out..
Don’t have a durston mill but I saved for forever and got a Pepe mill. Pepe vs durston vs cheap economy, went mid for Pepe. I want a durston mill eventually. Pepe mill you can see how the cog spacing does affect the mill work. Good work Andrew 👍
Thanks a lot for the tip. What about very thin wires for example 0.5 mm in diameter, how do you taper the end of wire?
I always filled the end, but I’m also a beginner in this hobby using the mill or hammering so much quicker thank you gonna make some Cuban link bracelets
that's hard metal, guessing it must be white gold. Great to see the mill way! Thank you.
Is there any way or do you have a video on soldering 3mm or larger diameter silver rod made into large jump rings with a butane torch. Children in the house and i dont feel the most comfortable with buying oxy mapp or other large torches inside. Would i need to use a special torch for the 14oz bottles of butane? Or will a refillable torch work for larger jump rings. Wanting to make a curb bracelet. Around 10mm so would need to be strong joints for the twist.
Andrew, how often do you throw darts at your door?
Merry Christmas. Andrew Thank you so much I would like to send u a pic of my new ring set..where do I send it to?"
@Atthebench
5 жыл бұрын
Maria Gloria Gentile andrew@andrewberry.co.uk
Do you know any good book about diamonds?
Does wire then become work-hardened by it through the draw plate and then need re-annealing?
@moonshinesa8234
5 жыл бұрын
Yes it does, you have to anneal it as soon as it becomes too difficult to pull the wire through.
If you have mill why would you use a draw plate? Can this not be done entirely on a rolling mill?
@Atthebench
5 жыл бұрын
Ray A rolling mill can not roll round wire and also a rolling mill can not roll square wire with crisp sharp corners
I would of liked to seen how you "aneed" ? the metal. .. where do I find that vid?
@TheTubeofjo
5 жыл бұрын
V Ewald its annealing, heating the metal to a cherry red which allows the metal to be softened, so you can continue to work the metal.
@Atthebench
5 жыл бұрын
V Ewald I have already done a film on annealing on YT already kzread.info/dash/bejne/d3h-kpqxmc6qeZc.html
Why don't you just buy some 2mm diameter silver wire?
@Atthebench
Жыл бұрын
You don’t need to tie up money in silver lying around unused for months and years in sizes that you don’t use often. Buy one or two sizes and you can quickly make the size you want when you want
@Atthebench
Жыл бұрын
Yes I could but this way I can recycle my own silver plus I don’t have to wait for the size I need to be delivered plus I don’t have to pay postage