You forgot Option 4: Shooting it out with a 357 Magnum
@DANIAC262
9 ай бұрын
Lmao
@pinkyhotmessx69
6 ай бұрын
My preferred method lol
@ahis3233
2 ай бұрын
@@pinkyhotmessx69the Americans way
@parthiban8016
19 күн бұрын
Option 5: setting up plastic explosives. Idiot.
@tuliptime6 жыл бұрын
I wish everyone on youtube would be as too the point as you. No nonsense & easy to understand. No gabbing on about nothing before they get to the point you want to know about. Thank you very much.
@assmonster666
6 жыл бұрын
yes. and no pointless intros. "Hi I'm bill from blah blah..."
@crusader3012 Жыл бұрын
Try using a drill bit that's the same size as the rivet; the hole can still be used again if you are only making an adjustment to your work piece. The other two methods? That's for butchers or demolition work.
@jpatty5473
Жыл бұрын
haha, butchers. i had a good laugh there
@TheHappyKamper3 жыл бұрын
This is like saying "You can wipe your arse with nice 3 ply toilet paper, but there's also sandpaper if you're into more painful and messy results..."
@lx8980
3 жыл бұрын
Lol
@64seweryn
3 жыл бұрын
Mpre like you can wipe with plywood, a cactus, or poison ivy
@christianhenry4173
3 жыл бұрын
The drill is probably the safest for novice like me.
@3eyedking178
3 жыл бұрын
The problem is, for some people without the deluxe tp, and only sandpaper, we don't really have an option. Well at least we'll also have the benefit of a polished asshole in the future😁
@pureplay7071
2 жыл бұрын
🤣🤣
@hazmatracing6 жыл бұрын
I'm with the drilling
@ber2996
2 жыл бұрын
Drilling looks clean
@TRUCKERCOLT
2 жыл бұрын
And easier.
@leocorral
2 жыл бұрын
I always just hammer through
@ArturoGonzalez-ik9zo
2 жыл бұрын
Drilling is faster until it’s a stainless steel river that’s over head. Those hot shavings suck and when your trying to hurry the fuck up that’s when your bit goes dull real fast
@thomasholmes341
2 жыл бұрын
@@ArturoGonzalez-ik9zo Use a low speed with higher pressure when drilling or cutting stainless steel.
@Jarsia4 жыл бұрын
Interesting video. Absolutely riveting
@RJ-jl9yf
2 жыл бұрын
lol
@skipgrows16222 жыл бұрын
If you plan to reuse the rivet hole don't use an oversized bit. Keep it the same size as it was originally drilled with. The pieces will go back together cleanly. Most of what I install in ships is riveted. Upwards of 15k+ rivets per project with 2 guys. Granted we rarely have to remove any but it happens and drilling is by far the cleanest method.
@ajdaly56343 жыл бұрын
Very clear and instructional video. You outlined the methods, tools, added titles and illustrated each. Great presentation. Very helpful. Thank you for your time and efforts and for sharing. All the blessings to you.
@holly45236 жыл бұрын
Don’t pay attention to all the sarcasm on here; the video was a great way to let me know my options. I’m trying to remove rivets from hardware on a vintage suitcase, so either a tiny drill will work or the screwdriver/chisel method will work. Thank you for a clear and concise video. Have a great day!
@Twistedstar0320
3 жыл бұрын
The correct drill size, drill only far enough into the head for the correct size punch to fit inside.. rheem the punch in the rivet head around in circles. If the head doesn't pop off easily then drill a little more. Once the head is taken off with the punch, take a small hammer and knock it the rest of the way through with the punch. That chisel method is going to mar up the surface.
@holly4523
3 жыл бұрын
@@Twistedstar0320 I appreciate your response. I actually managed to remove the rivets shortly after I posted this comment 2 years ago. Lol. Thank you for your advice, however; I can keep it in mind if I have any similar tasks in the future. Have an awesome day/night. And stay safe and healthy from this awful pandemic.
@bluegirl43262 жыл бұрын
Thank you I successfully removed the rivets on my storm door using a hammer and chisel thanks to you.
@dalmain704 жыл бұрын
Great, easy video, answered all my questions! Thanks!
@Bellatorlucis7 жыл бұрын
Gentlemens, please do not judge strictly author. Video is called the "three ways..." but not "three CORRECT ways..."))) so you can add more methods - for example - removing rivets with the explosives or you can use s some strong acid)))
@madradthyqia1235
Жыл бұрын
😂😂
@3piece5984 жыл бұрын
Thanks! Thought this would maybe be tougher with a chisel , watched you do it, saw that it was easy and got rid of my own rivets in seconds- thanks again!
@davidtrov37483 жыл бұрын
Thanks for showing me this way... I've been looking for this to disassemble my old PC case.
@GodwillDemiGod Жыл бұрын
Thank you. This helped. I go with the drill. Its super clean
@elizabethdimarco53906 жыл бұрын
Thank You for posting this great video!! It helped me out so much trying to fix my screen door!! I finally got things done that I had not been able to do because I thought I didn't know how!! But your methods worked so great!! I fixed my door and I didn't even have to use my friend's help( because he really can't fix nothing he thinks he can lol)!! You are awsome!!
@premiere3610 Жыл бұрын
I just drilled out rivets using 4mm drill bit. It's so easy. Thank you very much.
@bburns24782 жыл бұрын
Was totally stuck and I've just tried this - worked perfectly. Thank you so much.
@waifung33678 ай бұрын
thank you for this, I came across a project that needs me removing the rivet on the appliance I will be working on, I am still green and have not many experience with rivets, now I know what I have to do. Thank you and God bless.
@CDinkle5 жыл бұрын
Drill is definitely the cleanest/quickest/easiest route.
@chrisdavis8412
4 жыл бұрын
Can I use a hammer drill?
@jegr3398
4 жыл бұрын
Unless the rivet spins
@NutflX
3 жыл бұрын
Mm dont use brass One snapped and a tiny bit flew just below my nose. Use eye protection lads.
@zyriik6 жыл бұрын
Veeery nicely demonstrated, I plan to be removing rivets from leather HOWEVER, I could REALLY use this on the damage decorating of my truck with all of these techniques. Thank you so very much! ^__^
@Katy809RD4 жыл бұрын
Thanks for all the options! Don’t have many fancy tools. Great to know I can do it with a drill.
@patpathinayake35862 жыл бұрын
Thank you very much. Simple and very effective methods. Best of luck.
@davfree97326 жыл бұрын
Thanks for posting this video. I have a bowen's reflector head with a dent that popped out a rivet. Since the metal on the attaching piece is thinner than the head and prone to bending I need to take out the rivet's in order to removed the dents. The drill approach looks the least destructive
@jerrybockes47695 жыл бұрын
Thank u to who ever made this video now I can finally remove my door tag off my 1978 f250
@yolandarivera68723 жыл бұрын
Love the first method! Thank you for doing the video
@Jeremy_alfa4 ай бұрын
Using these pull through rivets at work to bind a plastic cover to an aluminum base. Pain in the butt when it doesn't go all the way through with the gun and takes forever to try and pull it out or sand down without it being noticeable. Happened again right now and never thought about hammering it out, worked like a charm!
@davegoldsmith40204 жыл бұрын
Always drill from the head side, ensure you have the correct size drill, make sure you hold the drill square to the hole, STOP as soon as the head separates, DO NOT push the drill thorough the hole several times, or you will will end up with an enlarged hole. and need a a bigger rivet or it will not have the same grip as the original. but the main thing is to ensure you are central on the rivet or you will end up with a figure of eight shaped hole. Punch out the rivet remains and remove any swarf before you re rivet. Beware the removed rivet head may be hot and will be sharp. remove from the drill bit with care.
@Shazzkid
4 жыл бұрын
Lol yh that annoyed me why he pecked the drill through several times...
@meals24u
3 жыл бұрын
How do I determine the correct bit size? I’m looking to open and repack a motorcycle exhaust and it’ll need to be re riveted. I want it to look clean and not damage the beautiful exhaust.. (so grinder and chisel are out of option)
@davegoldsmith4020
3 жыл бұрын
8meals one thing you can do is check with rivets you will use on the repair. The drill bit is better slightly small rather than to big. Once the first head is off you can use hole as a guide before drilling the others. If you have rivets that are hard to get to . Do one easy one to get the size of the bit you need then do the awkward ones . Best of luck
@davegoldsmith4020
3 жыл бұрын
8meals one other thing if the old rivet spins rather than the head breaks off do not wiggle the drill stop or the hole will become enlarged try using a punch if that does not work you need a slightly bigger drill bit
@meals24u
3 жыл бұрын
Dave Goldsmith Okay, awesome thanks for the wonderful advice!! Gonna give it a shot! Thanks again
@3lostblonds7 жыл бұрын
Thank you for posting! I see there are clean and rather messy ways of removal too !
@kathrynnewton8721 Жыл бұрын
Thank you, you make it look so easy in the vice but when trying to remove table top supports it’s more tricky!
@MrSqterror2 жыл бұрын
thanks for the idea..had issues with a dell pedge2900 case. 1st method its the best for PC/Server cases.
@MarkHewis4 жыл бұрын
I think the drill works best in above. The other 2 methods more complicated if the sheet has been painted over. Just thinking best when using pop rivets to use the smallest size for job in case need to drill out .
@wizkid91us7 жыл бұрын
Very informative! Thank you for posting.
@tedigrizli2 жыл бұрын
From everyone that has a non-removable optical drive cage in their computer case - THANK YOU!
@smoreno12363 жыл бұрын
Drilling is the fastest and cleanest way in my opinion 👍
@kittykat24547 жыл бұрын
Thanks for the video, I drilled out the rivets. Many thanks again!!
@nestawestchickenwing3 жыл бұрын
This helped so much , I had everything except a drill and the screw driver one worked great . 😊
@guppy01123 жыл бұрын
Needed this! Thanks, man!
@ssandde7 жыл бұрын
Stupidly simple, but excellent video! Helped me out a lot, being a 'city' boy.
@OsheaBenGolab3 жыл бұрын
Lol love the thumbs up 👍🏾.... great video. Simple and easy thanks
@alsn1262 жыл бұрын
Thank you I successfully removed a rivet off my car using the drill method
@avanishbhurke72304 ай бұрын
Thanks a lot man, learned something new today ❤
@andyrulz26266 жыл бұрын
I have a carbon fiber spoiler, so i think drilling them out without damaging the wing is best for me. Thank you for this video👍
@Henjo294 жыл бұрын
Hammer and thick screwdriver did the trick, breaking down my old pc tower. Thank you!
@horizontutorials9409
4 жыл бұрын
yea same thats why i watched this video. i have a old pc and stupid hp decided to rivet in the back pannel
@zacoutortue009
4 жыл бұрын
@@horizontutorials9409 fuck man i had the same problem why the fuck did someone ever think this was a good idea
@nicolasconde42393 жыл бұрын
A really helpful video! 🙏🙏
@bojankljajic54084 жыл бұрын
Can you show us what rivet gun did you use to put those rivets at battens? Do you know dimensions of those rivets? This aluminum battens look like dry van trailer side battens.
@tristanjacobucci4 жыл бұрын
Followed the drill method here and it worked fine for getting the heads out, then I used a punch and hammer to pop out the rest of the rivet.
@fredgrave2153Ай бұрын
If a rivet is loose (so it'll just spin when you try to drill it), is the only option to hammer and chisel it? Anybody know any other options that are less likely to damage something?
@randisallah3 жыл бұрын
I'd just like to say that I like things like that big old chisel, probably used to be twice that size. It's just been grinded down that many times its shrunk. A proper bloke with proper tools that have been well used and he even has the proper big old tough hands and sausage fingers. Now that's what I'd say is a proper bloke, a geezer or just a Man's Man. Just soldiers on and takes care of business, well done 👍.
@MarCo-rb8ul8 жыл бұрын
this helped a lot! didnt have any other tools but a hammer and a screwdriver lol just had to tear apart the rivets
@midfutballr2 жыл бұрын
Thanks for posting.
@dimensionexo.2 жыл бұрын
Kool,think I'll try the drill first.That chisel had a sharp edge.
@kentsgodfrey25133 жыл бұрын
Thanks! Very useful.
@Fantomaxe Жыл бұрын
Thanks for the Video great technique
@rhysfagan62596 жыл бұрын
what size drill bit did you use?
@JusMonDay2 жыл бұрын
Just my two cents. The drill works good for maybe or two rivets if your lucky. I learned that using a grinder for the first initial removal and once you get it down far enough you can use a punch and a good hammer to finish the holes off. I can do a rivet a minute or so. Im working on a box truck door hardware every single hinge and roller need replaced. If anyone's ever looking for the hardware you can find it on ebay. Make sure you get the right sized wheels. Hope that helps someone. I abandoned the drill all together.
@Greenriver8423 жыл бұрын
Love it, thanks 👏🏻
@rominhawk39493 жыл бұрын
To me it looked like the fastest method is the chisel and hammer; All methods will scratch the side being worked on; and It's a pain when drilling a rivet and it starts to spin with the drill bit. I had never thought of using a chisel and hammer; wow, that is fast and with a little care, can be not too damaging. Cheers. Thanks for sharing. Good video.
@jacintarichardson237610 ай бұрын
This repair is beautiful for breathing new life into a solid toolbox. It has increased the security of the toolbox from one where eventually the lid would break off on its own to one where there is no risk of that. But the repair is not as secure as the original design. The original design was built with hidden hinges so that an attacker had to attack the locking mechanism to get in. And it's a good locking mechanism. Rivets are easy to break through with only a hammer and a screwdriver. This fix will keep opportunists away, and keep your stuff dry, but it is not better than replacing the product under warranty when it comes to thieves who are willing to carry a screwdriver and a hammer which is a pretty low bar.
@AdrianLopez-sc6zw4 жыл бұрын
Thanks.. Drilling was not con my train pf toughts.. I used pliers (extremly difficult) now i'll go with dtilling
@prorican697 жыл бұрын
Great upload. Thanks!!
@blackjack444....7 жыл бұрын
The drill all day!! 💪thanks!
@ernestospingpong6 жыл бұрын
number 2 the best for car speakers!!!!!
@mrrr4079 ай бұрын
I did the drill was very helpful
@adrianmierzwa32383 жыл бұрын
Drill should be exact or 1mm thicker than rivet tail. Drill should never go trough the material just remove the head and pinch the pin trough. It is important not to enlarge the hole 1) because sometimes rivets are visible on a cover - You don't want to put another rivet off center - You want to put the same rivet in the same place in original hole. 2) what about another time? You cant enlarge the hole each time and put larger rivet. This way You can do it 100 times and get the same result. 3) what if the hole itself has antirust surface protection inside? drilling it off will remove this surface and will lead to rusting.
@baatyr9430
2 жыл бұрын
Using a bolt and screw is also an option
@meroadel61734 жыл бұрын
Thank you u helped me
@MandyMireles Жыл бұрын
Thank you so much 👍🏻👍🏻👍🏻👍🏻👍🏻👍🏻👍🏻👍🏻👍🏻👍🏻👍🏻👍🏻🤗
@uniquereviewshacks21213 жыл бұрын
I don't have any power tools, chopped the head with a hand saw it worked, thanks.
@fitzi404 жыл бұрын
Thanks for this. I’m taking apart an old toolbox so this was helpful
@68spaceman7 жыл бұрын
This is great, thank you. What I can't seem to find out though, is the best way to remove the rivet heads from the drill bit - after drilling out the rivet. I noticed you pushed them up against the chuck each time.
@crooked-halo
7 жыл бұрын
I use a pliers, grab the rivet heads, and hand-spin the drill in opposite direction.
@pats.42683 жыл бұрын
Thank you very much!
@raul93046 жыл бұрын
Thank you so much.
@spencermaiers83226 жыл бұрын
This guy's hands are awesome. Imagine all the pasty handed complainers analyzing his technique! Good on ya man, your hands deserve their own t-shirt. Surely a hard workin' fella.
@timothy790110
6 жыл бұрын
he could probably remove the rivets with no tool with them!
@SpallinJ7 жыл бұрын
Thanks for the informative video! Can you recommend a good grinder, sort of like the one you use in your video? I'm in the market for one and I'm not sure what the good brands and models are.
@aaronrstman1838
6 жыл бұрын
SpallinJ . Personally I own Two different brands and they have never let me down. They are a MAKITA 4 1/2 and MILWAUKEE 4 1/2” & 5 1/2” one having a “paddle style” switch which offers more control over longer usage through comfort and not having to fumble for a slide/on-off switch. (Just MY personal preference) hope that helps if you haven’t by now purchased one of your own already.
@townsville696 жыл бұрын
how do you work out what size drill to use ? Im replacing the rivets that hold in the bung seat on my boat and I don't want to make the hole too big.
@davfree9732
6 жыл бұрын
Start small and increase the drill bit size after each drill until you reach the point where the rivet can be removed. Without knowing the exact size of the hole, this 'work your way up' approach will prevent making a bigger hole and reveal the size of bit you need to remove the rest.
@mathewdoyle33636 жыл бұрын
You make my man hands look like girl hands. And you hand tools look they could tell alot of good stories. Thank you the good tips. Party on bud.
@PaulQuito217 жыл бұрын
Hopefully you've never done this on an aircraft lmao
@christen1075 Жыл бұрын
Thank you. I'd forgotten the hammer and chisel method. Normally I'm not a music fan, but in your case, it was pretty upbeat.... Gracias
@ezandman6804
Жыл бұрын
Yeah dude... The tune was great, lol
@jaytodd58092 жыл бұрын
What about those crazy split rivets used on car door window tracks..how do we remove those without breaking the glass?.!!
@sabiner.93566 жыл бұрын
Thank you !
@destruxandexploze25522 жыл бұрын
Drilling is the cleanest and seems like the best/easiest way
@PCWIZMTL8 жыл бұрын
@1:43, the rivets and the bolt on the piece of wood give the illusion of a dog. PS: Thanks for the tips!
@phyllissmith56092 жыл бұрын
OK, even I can do one of these. Thanks for more than 1 option.
@Adrian21404 жыл бұрын
Rivets are stupid. Just use an appropriate screw...
@krixloaf2610
4 жыл бұрын
sometimes theres no way to get ur finger to the other side to hold the nut not to mention insert it. This could be the best way to put together thin layers of plastic or aluminium materials, i.e., placing a door hinge lock onto a plastic door.
@Adrian2140
4 жыл бұрын
@@krixloaf2610 You have pan heads or truss heads for that. For any type of problem there is an appropriate screw you can use. I'm particularly pissed on rivets right now because the exhaust shields under my car, which have holes in them, are bolted in with rivets. Thanks to some dumb fuck that wanted to save a few $$ I now have to drill in the car frame to replace them with new fresh plates and the appropriate screws that should have been there from the factory. Fuck rivets.
@jegr3398
4 жыл бұрын
@@Adrian2140 OH BOO HOO HOO!!! 😭😭😭😭😭😭😭😭 Cry more
@Adrian2140
4 жыл бұрын
@@jegr3398 Is being a moron a hobby for you or are you competing nationally?
@jegr3398
4 жыл бұрын
@@Adrian2140 You're the one who can't get a rivet out 🤷♂️
@JohnSmithZen3 жыл бұрын
Thank you!!!
@EducationProfessional-pc6ep10 ай бұрын
Nice video. I don't have a grinder so will try options 1 and 3
@mastertcze
2 ай бұрын
Go for drill, does not damage the stuff around so much 🙂
@arbiteroftaste6 жыл бұрын
What are those rivets made of? Aluminum?
@kyummm2 жыл бұрын
I'll go with the drilling clean and simple
@JackMelonz Жыл бұрын
Tqsm
@davidartwales85125 жыл бұрын
Thanks for making a helpful video that isn't filled with boring yammer. :)
@CindyVideos4you7 жыл бұрын
Thank you, thumb guy!
@kennydieu26942 жыл бұрын
Good video and thanks for sharing
@facereader992 жыл бұрын
Regular drill bit or reversing drill bit, like the one used for extracting?
@sapafernando1
2 жыл бұрын
Regular drill bit
@rivetking7 жыл бұрын
I manufacture rivets, and often drill them out for testing purposes. Best ways as a fact. Diameter drill should match the head diameter of the rivet head. Then gradually shave it off until the tail falls out the other side. The shave concept, versus drill out it key, which is most effectively done with a larger drill dimeter. Smaller drill bits equal to or close to the body doesn't work well as the helix will catch causing the rivet to torque out which then means you can't shave it anymore. Absolutely no damage to the surfaces with good practice
@HoangNguyen-bh3xe
7 жыл бұрын
RivetKing Products l
@keithtraa
7 жыл бұрын
I don't believe it.
@betterday2570
7 жыл бұрын
RivetKing Products I use this method often on powder coated surfaces.
@cuekumber32925 жыл бұрын
Thanks man
@christiand24262 жыл бұрын
Do i have some kind of bad drill? Mine just stops moving forward into the rivet and spins in place at some point.
@Twistedstar0320
2 жыл бұрын
Your drill bit is dull, or if the rivet is free spinning you'll need to use pliers or vice grip on the back side to hold it.
@GodwillDemiGod
Жыл бұрын
Use 4mm drill
@lindawhittle6969
Жыл бұрын
@@GodwillDemiGod thanks that worked
@rafaelmolina6544 жыл бұрын
Thank you
@mouradpacha26705 жыл бұрын
good video thank you
@Hindelaufen3 жыл бұрын
Very helpful. Too bad you forgot to mention the C4 and flame thrower method.
Пікірлер: 486
You forgot Option 4: Shooting it out with a 357 Magnum
@DANIAC262
9 ай бұрын
Lmao
@pinkyhotmessx69
6 ай бұрын
My preferred method lol
@ahis3233
2 ай бұрын
@@pinkyhotmessx69the Americans way
@parthiban8016
19 күн бұрын
Option 5: setting up plastic explosives. Idiot.
I wish everyone on youtube would be as too the point as you. No nonsense & easy to understand. No gabbing on about nothing before they get to the point you want to know about. Thank you very much.
@assmonster666
6 жыл бұрын
yes. and no pointless intros. "Hi I'm bill from blah blah..."
Try using a drill bit that's the same size as the rivet; the hole can still be used again if you are only making an adjustment to your work piece. The other two methods? That's for butchers or demolition work.
@jpatty5473
Жыл бұрын
haha, butchers. i had a good laugh there
This is like saying "You can wipe your arse with nice 3 ply toilet paper, but there's also sandpaper if you're into more painful and messy results..."
@lx8980
3 жыл бұрын
Lol
@64seweryn
3 жыл бұрын
Mpre like you can wipe with plywood, a cactus, or poison ivy
@christianhenry4173
3 жыл бұрын
The drill is probably the safest for novice like me.
@3eyedking178
3 жыл бұрын
The problem is, for some people without the deluxe tp, and only sandpaper, we don't really have an option. Well at least we'll also have the benefit of a polished asshole in the future😁
@pureplay7071
2 жыл бұрын
🤣🤣
I'm with the drilling
@ber2996
2 жыл бұрын
Drilling looks clean
@TRUCKERCOLT
2 жыл бұрын
And easier.
@leocorral
2 жыл бұрын
I always just hammer through
@ArturoGonzalez-ik9zo
2 жыл бұрын
Drilling is faster until it’s a stainless steel river that’s over head. Those hot shavings suck and when your trying to hurry the fuck up that’s when your bit goes dull real fast
@thomasholmes341
2 жыл бұрын
@@ArturoGonzalez-ik9zo Use a low speed with higher pressure when drilling or cutting stainless steel.
Interesting video. Absolutely riveting
@RJ-jl9yf
2 жыл бұрын
lol
If you plan to reuse the rivet hole don't use an oversized bit. Keep it the same size as it was originally drilled with. The pieces will go back together cleanly. Most of what I install in ships is riveted. Upwards of 15k+ rivets per project with 2 guys. Granted we rarely have to remove any but it happens and drilling is by far the cleanest method.
Very clear and instructional video. You outlined the methods, tools, added titles and illustrated each. Great presentation. Very helpful. Thank you for your time and efforts and for sharing. All the blessings to you.
Don’t pay attention to all the sarcasm on here; the video was a great way to let me know my options. I’m trying to remove rivets from hardware on a vintage suitcase, so either a tiny drill will work or the screwdriver/chisel method will work. Thank you for a clear and concise video. Have a great day!
@Twistedstar0320
3 жыл бұрын
The correct drill size, drill only far enough into the head for the correct size punch to fit inside.. rheem the punch in the rivet head around in circles. If the head doesn't pop off easily then drill a little more. Once the head is taken off with the punch, take a small hammer and knock it the rest of the way through with the punch. That chisel method is going to mar up the surface.
@holly4523
3 жыл бұрын
@@Twistedstar0320 I appreciate your response. I actually managed to remove the rivets shortly after I posted this comment 2 years ago. Lol. Thank you for your advice, however; I can keep it in mind if I have any similar tasks in the future. Have an awesome day/night. And stay safe and healthy from this awful pandemic.
Thank you I successfully removed the rivets on my storm door using a hammer and chisel thanks to you.
Great, easy video, answered all my questions! Thanks!
Gentlemens, please do not judge strictly author. Video is called the "three ways..." but not "three CORRECT ways..."))) so you can add more methods - for example - removing rivets with the explosives or you can use s some strong acid)))
@madradthyqia1235
Жыл бұрын
😂😂
Thanks! Thought this would maybe be tougher with a chisel , watched you do it, saw that it was easy and got rid of my own rivets in seconds- thanks again!
Thanks for showing me this way... I've been looking for this to disassemble my old PC case.
Thank you. This helped. I go with the drill. Its super clean
Thank You for posting this great video!! It helped me out so much trying to fix my screen door!! I finally got things done that I had not been able to do because I thought I didn't know how!! But your methods worked so great!! I fixed my door and I didn't even have to use my friend's help( because he really can't fix nothing he thinks he can lol)!! You are awsome!!
I just drilled out rivets using 4mm drill bit. It's so easy. Thank you very much.
Was totally stuck and I've just tried this - worked perfectly. Thank you so much.
thank you for this, I came across a project that needs me removing the rivet on the appliance I will be working on, I am still green and have not many experience with rivets, now I know what I have to do. Thank you and God bless.
Drill is definitely the cleanest/quickest/easiest route.
@chrisdavis8412
4 жыл бұрын
Can I use a hammer drill?
@jegr3398
4 жыл бұрын
Unless the rivet spins
@NutflX
3 жыл бұрын
Mm dont use brass One snapped and a tiny bit flew just below my nose. Use eye protection lads.
Veeery nicely demonstrated, I plan to be removing rivets from leather HOWEVER, I could REALLY use this on the damage decorating of my truck with all of these techniques. Thank you so very much! ^__^
Thanks for all the options! Don’t have many fancy tools. Great to know I can do it with a drill.
Thank you very much. Simple and very effective methods. Best of luck.
Thanks for posting this video. I have a bowen's reflector head with a dent that popped out a rivet. Since the metal on the attaching piece is thinner than the head and prone to bending I need to take out the rivet's in order to removed the dents. The drill approach looks the least destructive
Thank u to who ever made this video now I can finally remove my door tag off my 1978 f250
Love the first method! Thank you for doing the video
Using these pull through rivets at work to bind a plastic cover to an aluminum base. Pain in the butt when it doesn't go all the way through with the gun and takes forever to try and pull it out or sand down without it being noticeable. Happened again right now and never thought about hammering it out, worked like a charm!
Always drill from the head side, ensure you have the correct size drill, make sure you hold the drill square to the hole, STOP as soon as the head separates, DO NOT push the drill thorough the hole several times, or you will will end up with an enlarged hole. and need a a bigger rivet or it will not have the same grip as the original. but the main thing is to ensure you are central on the rivet or you will end up with a figure of eight shaped hole. Punch out the rivet remains and remove any swarf before you re rivet. Beware the removed rivet head may be hot and will be sharp. remove from the drill bit with care.
@Shazzkid
4 жыл бұрын
Lol yh that annoyed me why he pecked the drill through several times...
@meals24u
3 жыл бұрын
How do I determine the correct bit size? I’m looking to open and repack a motorcycle exhaust and it’ll need to be re riveted. I want it to look clean and not damage the beautiful exhaust.. (so grinder and chisel are out of option)
@davegoldsmith4020
3 жыл бұрын
8meals one thing you can do is check with rivets you will use on the repair. The drill bit is better slightly small rather than to big. Once the first head is off you can use hole as a guide before drilling the others. If you have rivets that are hard to get to . Do one easy one to get the size of the bit you need then do the awkward ones . Best of luck
@davegoldsmith4020
3 жыл бұрын
8meals one other thing if the old rivet spins rather than the head breaks off do not wiggle the drill stop or the hole will become enlarged try using a punch if that does not work you need a slightly bigger drill bit
@meals24u
3 жыл бұрын
Dave Goldsmith Okay, awesome thanks for the wonderful advice!! Gonna give it a shot! Thanks again
Thank you for posting! I see there are clean and rather messy ways of removal too !
Thank you, you make it look so easy in the vice but when trying to remove table top supports it’s more tricky!
thanks for the idea..had issues with a dell pedge2900 case. 1st method its the best for PC/Server cases.
I think the drill works best in above. The other 2 methods more complicated if the sheet has been painted over. Just thinking best when using pop rivets to use the smallest size for job in case need to drill out .
Very informative! Thank you for posting.
From everyone that has a non-removable optical drive cage in their computer case - THANK YOU!
Drilling is the fastest and cleanest way in my opinion 👍
Thanks for the video, I drilled out the rivets. Many thanks again!!
This helped so much , I had everything except a drill and the screw driver one worked great . 😊
Needed this! Thanks, man!
Stupidly simple, but excellent video! Helped me out a lot, being a 'city' boy.
Lol love the thumbs up 👍🏾.... great video. Simple and easy thanks
Thank you I successfully removed a rivet off my car using the drill method
Thanks a lot man, learned something new today ❤
I have a carbon fiber spoiler, so i think drilling them out without damaging the wing is best for me. Thank you for this video👍
Hammer and thick screwdriver did the trick, breaking down my old pc tower. Thank you!
@horizontutorials9409
4 жыл бұрын
yea same thats why i watched this video. i have a old pc and stupid hp decided to rivet in the back pannel
@zacoutortue009
4 жыл бұрын
@@horizontutorials9409 fuck man i had the same problem why the fuck did someone ever think this was a good idea
A really helpful video! 🙏🙏
Can you show us what rivet gun did you use to put those rivets at battens? Do you know dimensions of those rivets? This aluminum battens look like dry van trailer side battens.
Followed the drill method here and it worked fine for getting the heads out, then I used a punch and hammer to pop out the rest of the rivet.
If a rivet is loose (so it'll just spin when you try to drill it), is the only option to hammer and chisel it? Anybody know any other options that are less likely to damage something?
I'd just like to say that I like things like that big old chisel, probably used to be twice that size. It's just been grinded down that many times its shrunk. A proper bloke with proper tools that have been well used and he even has the proper big old tough hands and sausage fingers. Now that's what I'd say is a proper bloke, a geezer or just a Man's Man. Just soldiers on and takes care of business, well done 👍.
this helped a lot! didnt have any other tools but a hammer and a screwdriver lol just had to tear apart the rivets
Thanks for posting.
Kool,think I'll try the drill first.That chisel had a sharp edge.
Thanks! Very useful.
Thanks for the Video great technique
what size drill bit did you use?
Just my two cents. The drill works good for maybe or two rivets if your lucky. I learned that using a grinder for the first initial removal and once you get it down far enough you can use a punch and a good hammer to finish the holes off. I can do a rivet a minute or so. Im working on a box truck door hardware every single hinge and roller need replaced. If anyone's ever looking for the hardware you can find it on ebay. Make sure you get the right sized wheels. Hope that helps someone. I abandoned the drill all together.
Love it, thanks 👏🏻
To me it looked like the fastest method is the chisel and hammer; All methods will scratch the side being worked on; and It's a pain when drilling a rivet and it starts to spin with the drill bit. I had never thought of using a chisel and hammer; wow, that is fast and with a little care, can be not too damaging. Cheers. Thanks for sharing. Good video.
This repair is beautiful for breathing new life into a solid toolbox. It has increased the security of the toolbox from one where eventually the lid would break off on its own to one where there is no risk of that. But the repair is not as secure as the original design. The original design was built with hidden hinges so that an attacker had to attack the locking mechanism to get in. And it's a good locking mechanism. Rivets are easy to break through with only a hammer and a screwdriver. This fix will keep opportunists away, and keep your stuff dry, but it is not better than replacing the product under warranty when it comes to thieves who are willing to carry a screwdriver and a hammer which is a pretty low bar.
Thanks.. Drilling was not con my train pf toughts.. I used pliers (extremly difficult) now i'll go with dtilling
Great upload. Thanks!!
The drill all day!! 💪thanks!
number 2 the best for car speakers!!!!!
I did the drill was very helpful
Drill should be exact or 1mm thicker than rivet tail. Drill should never go trough the material just remove the head and pinch the pin trough. It is important not to enlarge the hole 1) because sometimes rivets are visible on a cover - You don't want to put another rivet off center - You want to put the same rivet in the same place in original hole. 2) what about another time? You cant enlarge the hole each time and put larger rivet. This way You can do it 100 times and get the same result. 3) what if the hole itself has antirust surface protection inside? drilling it off will remove this surface and will lead to rusting.
@baatyr9430
2 жыл бұрын
Using a bolt and screw is also an option
Thank you u helped me
Thank you so much 👍🏻👍🏻👍🏻👍🏻👍🏻👍🏻👍🏻👍🏻👍🏻👍🏻👍🏻👍🏻🤗
I don't have any power tools, chopped the head with a hand saw it worked, thanks.
Thanks for this. I’m taking apart an old toolbox so this was helpful
This is great, thank you. What I can't seem to find out though, is the best way to remove the rivet heads from the drill bit - after drilling out the rivet. I noticed you pushed them up against the chuck each time.
@crooked-halo
7 жыл бұрын
I use a pliers, grab the rivet heads, and hand-spin the drill in opposite direction.
Thank you very much!
Thank you so much.
This guy's hands are awesome. Imagine all the pasty handed complainers analyzing his technique! Good on ya man, your hands deserve their own t-shirt. Surely a hard workin' fella.
@timothy790110
6 жыл бұрын
he could probably remove the rivets with no tool with them!
Thanks for the informative video! Can you recommend a good grinder, sort of like the one you use in your video? I'm in the market for one and I'm not sure what the good brands and models are.
@aaronrstman1838
6 жыл бұрын
SpallinJ . Personally I own Two different brands and they have never let me down. They are a MAKITA 4 1/2 and MILWAUKEE 4 1/2” & 5 1/2” one having a “paddle style” switch which offers more control over longer usage through comfort and not having to fumble for a slide/on-off switch. (Just MY personal preference) hope that helps if you haven’t by now purchased one of your own already.
how do you work out what size drill to use ? Im replacing the rivets that hold in the bung seat on my boat and I don't want to make the hole too big.
@davfree9732
6 жыл бұрын
Start small and increase the drill bit size after each drill until you reach the point where the rivet can be removed. Without knowing the exact size of the hole, this 'work your way up' approach will prevent making a bigger hole and reveal the size of bit you need to remove the rest.
You make my man hands look like girl hands. And you hand tools look they could tell alot of good stories. Thank you the good tips. Party on bud.
Hopefully you've never done this on an aircraft lmao
Thank you. I'd forgotten the hammer and chisel method. Normally I'm not a music fan, but in your case, it was pretty upbeat.... Gracias
@ezandman6804
Жыл бұрын
Yeah dude... The tune was great, lol
What about those crazy split rivets used on car door window tracks..how do we remove those without breaking the glass?.!!
Thank you !
Drilling is the cleanest and seems like the best/easiest way
@1:43, the rivets and the bolt on the piece of wood give the illusion of a dog. PS: Thanks for the tips!
OK, even I can do one of these. Thanks for more than 1 option.
Rivets are stupid. Just use an appropriate screw...
@krixloaf2610
4 жыл бұрын
sometimes theres no way to get ur finger to the other side to hold the nut not to mention insert it. This could be the best way to put together thin layers of plastic or aluminium materials, i.e., placing a door hinge lock onto a plastic door.
@Adrian2140
4 жыл бұрын
@@krixloaf2610 You have pan heads or truss heads for that. For any type of problem there is an appropriate screw you can use. I'm particularly pissed on rivets right now because the exhaust shields under my car, which have holes in them, are bolted in with rivets. Thanks to some dumb fuck that wanted to save a few $$ I now have to drill in the car frame to replace them with new fresh plates and the appropriate screws that should have been there from the factory. Fuck rivets.
@jegr3398
4 жыл бұрын
@@Adrian2140 OH BOO HOO HOO!!! 😭😭😭😭😭😭😭😭 Cry more
@Adrian2140
4 жыл бұрын
@@jegr3398 Is being a moron a hobby for you or are you competing nationally?
@jegr3398
4 жыл бұрын
@@Adrian2140 You're the one who can't get a rivet out 🤷♂️
Thank you!!!
Nice video. I don't have a grinder so will try options 1 and 3
@mastertcze
2 ай бұрын
Go for drill, does not damage the stuff around so much 🙂
What are those rivets made of? Aluminum?
I'll go with the drilling clean and simple
Tqsm
Thanks for making a helpful video that isn't filled with boring yammer. :)
Thank you, thumb guy!
Good video and thanks for sharing
Regular drill bit or reversing drill bit, like the one used for extracting?
@sapafernando1
2 жыл бұрын
Regular drill bit
I manufacture rivets, and often drill them out for testing purposes. Best ways as a fact. Diameter drill should match the head diameter of the rivet head. Then gradually shave it off until the tail falls out the other side. The shave concept, versus drill out it key, which is most effectively done with a larger drill dimeter. Smaller drill bits equal to or close to the body doesn't work well as the helix will catch causing the rivet to torque out which then means you can't shave it anymore. Absolutely no damage to the surfaces with good practice
@HoangNguyen-bh3xe
7 жыл бұрын
RivetKing Products l
@keithtraa
7 жыл бұрын
I don't believe it.
@betterday2570
7 жыл бұрын
RivetKing Products I use this method often on powder coated surfaces.
Thanks man
Do i have some kind of bad drill? Mine just stops moving forward into the rivet and spins in place at some point.
@Twistedstar0320
2 жыл бұрын
Your drill bit is dull, or if the rivet is free spinning you'll need to use pliers or vice grip on the back side to hold it.
@GodwillDemiGod
Жыл бұрын
Use 4mm drill
@lindawhittle6969
Жыл бұрын
@@GodwillDemiGod thanks that worked
Thank you
good video thank you
Very helpful. Too bad you forgot to mention the C4 and flame thrower method.
Thanks so much