Just stumbled across this channel. Great to see someone grafting as you are with a real positive attitude. Well done fella 👍

It's great to see young men grafting and doing well for themselves. So many youngsters nowadays don't know the meaning of hard work and serious grafting. Respect to you guys and you deserve all the luck you will definitely get.

@cassk9999

9 ай бұрын

Yeh I agree, hardworking young man grafting and hustling and with a positive non moaning attitude

@Ditcha1

4 ай бұрын

Great work ethic sadly lost to most of today’s generation

@callumboothroyd3766

4 ай бұрын

​@@Ditcha1 Maybe cause back in the 70s-80s wages were mental for the price of everything. House price to salary is now 12x more than the 70s. It's got nothing to do with our ethic and more to do with boomers getting everything and complaining still.

Hi Guys That Peugeot 107 Wheel Bearing job got me remembering way back when I was just starting my diy mechanic journey in 1986 when the front bearing on my 1969 Vauxhall viscount seized and I thought I had the knowledge and tools to do the job on my own, how wrong I was ! Working on the street in the evenings after my day job I got to the point where the bearing just wasn't coming out of the wheel bracket and using all the tricks I had up my sleeve including heat and wd40 couldn't make it budge so I had to trot over to my friendly motor garage chap who put the wheel bracket on his press but still no joy the bearing was literally welded to the axle spindle ! So in the end we had to get Mr AG (angle grinder) to separate the old bearing from axle, that did it but that was a learning curve to remember . Love watching you guys work and your ingenuity getting round problems, but please get in the habit of wearing face protection, eyes are precious and difficult to fix ! and ones lungs don't work properly with tons of shit and dust clogging them up ! Looking forward to seeing you guys tackle a Aston martin some day soon !

107/aygo/c1 wheel bearings 😱! For those bearing types, I find putting it on a pole in a vice then heating the bearing race specifically makes them fall off 😁 saves cutting into the shaft, the circlip is a royal pita on old ones. If you ever have time watch South Main Auto vids, Eric O is a master at dealing with rust and many other things……when he’s not moaning.

Fair play to these guys i wouldn't do a clutch on the floor for diamonds 😂

Huge respect for doing this on the driveway, that's kind of crazy :)

I hope this channel blows up, you lads are awesome ✌️ good honest people are hard to find these days. Good luck 👍

Its nice to watch a pair of grafters on youtube. Respect and wish your business success!

Omg...reminds me of time many many years ago changing my clutch on a 2.0 Ford cortina.Dropping the gearbox between my legs .Ouch !!! Hats off to you fellas.Keep safe.

Big respect to you guys, great work.

Love your content bro 👌 wishing you both All the best

330 am so bedtime for Me big up from Scotland boys keep up the good work. 😊

Thought you’d given up KZread? Welcome back and don’t disappear again 😂😂😂we all need you 😂😂😂

@themarvelousvlog

10 ай бұрын

Hahah! Camera gave up on me so had to come up with something. Bought insurance and all sorts for it now for the ‘just in case’ 😂

Dude you gave me the confidence to do my e90 318d flywheel i allways wounderd if i could get it high enough legend 👍

I once spent 2 days getting a c clip out from a kuga front hub. It was a pain in the ass 😂 Felt your pain on that wheel bearing bro 😮‍💨

A hammer and a impact screw driver is pretty good at removing those tough screws on break discs.

I love the car content, but lets be honest, John is the star 🤣🤣

@themarvelousvlog

2 ай бұрын

I’m just the explainer I am 😂

@kd2239

2 ай бұрын

@@themarvelousvlog 🤣🤣 Keep up the good work. Love your videos.

Nice ramps...you're the business no boys.

Always nice finding new car content. Just subbed. I do some car videos myself, mainly bmws tho

I wish you were near to me, I'd love to have someone who is reliable and does a first class job!

Wonderful work keep up.

Welcome back to KZread, you have been missed

@themarvelousvlog

10 ай бұрын

Back in full force now! Got camerassss now to make sure the content keeps on coming 😂 Thank you!

Your face when that disc retaining screw finally came out was a picture 😂…..no words needed.

Hi nice to see you back. I've the same press you have been using I changed a citroen camper van front wheel bearing and I couldn't get it out it bust the seal on me jack had oil every where I ended up having to heat it up really hot and I mean hot and use a 20 ton jack and it did crack in the end. Barry

@themarvelousvlog

10 ай бұрын

You saw how soaked it was in WD40 before popping out. I can imagine it’s only worse on bigger vehicles. Hate working on bearing, unless they come as a whole set 😂

Good video, respect to you going under the cars with no pit. Hey its true what they say - most dogs look like there owners 😂🤣 no offence 😊 keep up your good work 👌🏽

As an x mobile mechanic was doing it for twenty years and now I'm 62 years old and crippled with ages and pains all over my body out in all kind of weather .Hope u guys won't be the same .never again .

Done plenty wheel bearings in my 48years as a mechanic and yea some can be proper tight 😩and those circlips OMG I’ve been known to tack a few spots of MIG weld on them something to get a chisel on and the heat from the weld helps too. Great job there lads.

@themarvelousvlog

10 ай бұрын

Yeah, this one was one of them! Luckily no welding was involved. Sad thing is, all that work and it was charged at quoted price and not by the hour 😭

@kevinpalmer7452

10 ай бұрын

@@themarvelousvlog yea jobs like that can kick your BUT can take one hour or even Three 😩

@timfallowfield-cooper9673

10 ай бұрын

Grind a groove in inner bearing race and split it with chisel, then they just slide off.

Good job guys! tuloy nyo lang yan, para hindi mawalan ng pag asa ang mga taong nangangailangan ng tulong sa mga sariling gawain.. Watching from Antwerp Belgium mga lods! Mechanics 🛠💯

@themarvelousvlog

9 ай бұрын

Salamat Lodi!

@flipdamadapakincoin

9 ай бұрын

@@themarvelousvlog pa-shoutouts nlng sa next vid lods 😆 >>> Mac from antwerp belgium 💯🔥

Sehr gute Videos und Erfahrung die er hat. Bin schon etwas eifersüchtig das was er tut. Ich respektiere sehr seine Handwerks Kunst :=).

@themarvelousvlog

9 ай бұрын

Thank you!

to do wheel bearing in the parking area I used axle stand tube type to support the hub and an old wheel bearing and hit the old one with a sledge hammer many times

I'm in the motorcycle trade thinking about doing some videos myself great Job

You've got to use a impact driver on those retainer screws👍

Love watching your videos man but using that impact gun on the center disk bolts is risky could have probably prevented the strip. Lucky keep up the good work man 💯🔫

Spent 2 hours on the retaining clip on a mk5 gti no matter how much persuasion i used or the size it would not move broke it up mm by mm bearing sailed out and new one in 🤣🤣 broke my hopes and dreams that day.

Use a penetrating spray and a manual impact driver to get the disc retainer bolts moving. Best chance to avoid stripping if they are being difficult.

Welcome back. When you had the front of the car on the ramps you should have turned on the other way then it couldn't have rolled off 😉

@themarvelousvlog

10 ай бұрын

The reason why the ramps were put on the other way around is because it keeps on rolling back, hence why we done it that way 😉😅

@mrc_dan_gleeball1515

10 ай бұрын

Well it didn't move so all good 😀. Where do you get all your torque settings from?

@themarvelousvlog

10 ай бұрын

@mrc_dan_gleeball1515 Haynes, AutoData and AllData

@themarvelousvlog

10 ай бұрын

Nobody, and I mean nobody can explain how that feels 😂

Worked in sales , found hub in workshop begging for a stuck bearing removed, no body in workshop so I did as mechanic was missing tooling. Boy they were surprised.

need to get a impact screwdriver always comes in handy with the retaining screws

Copper-slip or Ceramic grease... love your work 🙂

In the future mate when you remove the hub from the bearing and that race gets stuck... as they always do face the studs upwards and the race downwards and Try and put it on some kind of spindle so you can spin it then just heat the race with a normal torch as your spinning the hub and the heat will pop the race off

This is why when I did my wheel bearing, I just bought a new knuckle & wheel hub. The amount of time it would cost to remove properly would be the same. As wheel bearings last 200k miles, I won't be doing this job again!

Iv had no end of problems with rusted retaining clips I weld an old chisel to them and rip them out the heat helps brake them free. You should use the old wheel bearing to push in the new one it help to not damage the new bearing.

I hate those kinda jobs. Did a berlingo ft bearing. Smashed knuckle. Then bought a 2nd hand hub with bearing and abs sensor for 50 quid. And said next time. Breakers yard for 2nd hand one. Easy way out but you know!! If it fixed its fixed haha

Good content man..some polite advice don’t end like me .. use good quality kneeling matt trust me you’ll thank me in years to come ..I paid the price by not doing so 😭

@themarvelousvlog

10 ай бұрын

I usually wear trousers with cushion in them, not this time though as it needed washing 😂 but yeah, totally agree with what you’re pointing out

Would have started with the Ratchet on them disk retaining bolts rather than the impact gun, I’ve learnt my lesson with this 1000’s of times 😂😂

@themarvelousvlog

10 ай бұрын

Usually hammering the Trx or Hex on it works. Not this time apparently 😂

@adamjones7538

10 ай бұрын

​@@themarvelousvlog1/2 short extension hammer a few times shocks the grub screw always. This skill has never let me down

@Mac_F87

10 ай бұрын

Manual impact driver is the way to go for them. Very unlikely to chew them up but enough to shock them and get them moving.

Halfords do an impact screwdriver that can be a good send for discs

I replaced my clutch on my Triumph Dolomite Sprint on the street. Luckily you could remove the transmission cover inside the car and have someone help lift the gearbox from above.

Wow so the first customer wiht the 1 series is just going to carry on with no 1st gear on his new clutch and flywheel? 😢

could of done that with the abs sensor still in 😅 just needed to be unplugged then do the bearing as normal but push it out with somthing the same size as the small ring of the beaing so it goes past the sensor there for not touching or damaging it but you probably noticed that wile doing it

They’re the worst thing the m sport callipers. And no they’re not the same disc size. They always do usually differ front to rear. The glue is to make sure the pads don’t always keep in contact with the disc and also for no excess movement.

Watch out for the dreaded CV joint splines seized in the drive flange, only had it once on a Ford Orion ( back in the day ), tried everything to get it out pressing and heating, hammering, all sorts, eventually had to scrap the whole hub assembly and got a replacement from the scrap yard...

@roy2689

10 ай бұрын

And of course had to replace the drive shaft too...

@golffish7599

9 ай бұрын

SDS drill on hammer only,chisel bit/point works like a charm.

@roy2689

9 ай бұрын

used an air chisel, still no dice, perhaps the chisel wasn't as charming as an SDS🤣

What brand are those orange ramps with the built in jack stand?

Good work 🎉 thanks for your efforts

You do great work but that poor ball joint dust cover at 8:24! 😢

I had the exact same problem with the circlip being siezed on my aygo. Managed to get a dremal with a cutting disc on it and cut the circlip into pieces then knocked them out with a hammer and chisel

Them Brembo brakes are shocking for squealing low speed… I’m guessing the “shim” is to help prevent this. Try what you like but when resonance stats on them discs notin’ is gonna help.

Hi love yr chanel have u got any of those caps goin

Impact screw-drivers work well with those pesky disc retaining screws.

@themarvelousvlog

2 ай бұрын

I did purchase one because I know I will be needing them A LOT

Does changing gearbox oil slow down clutch wear

Push the disk off with a bolt from behind. Takes 1 minute, no hammering. You will find u tube videos for it.

Keep up the good work BUT wear some eye protection when cleaning up the hubs with the wire brush, maybe even a mask. Time in clinics is time off work (and painful)

I used to fix my cars, love watching you , very informative, Timing was a cap you could advance and retard in my day

Wish we had the same power tools 40yrs ago when i was doing this lol

@themarvelousvlog

9 ай бұрын

Power tools are so handy! Best purchase I’d say

when you look AT 13:50 the bearing gos not in straight. when its not straight in one year its broken again.

Wow ang galing mo.

@themarvelousvlog

10 ай бұрын

Salamat po 🫡

Hi. What happened with the BMW you bought...did u manage to fix it.

Where are you guys based? How far would you travel and i meet you halfway if need to.

I have a 308 and was changing the pads bungee the caliper cleaned nad changed the pads and put it all together and the the break line into the caliper just popped off errr

Customer didn’t fancy replacing the gearbox then 😂 new clutch in 6 months time again then!

@themarvelousvlog

10 ай бұрын

He actually booked us in to replace it next week. Content incoming!

Had a mx5 drive shaft that wouldnt come out took the whole hub out and put 10 tonne on the shaft and lit it with oxy to finally get it out

Not a bearing. But I do mobile locking wheel nut removal. Wv golf on weds . Managed to turn a breaker bar in to a banana. Happens to often

@themarvelousvlog

10 ай бұрын

The worst of them all is the H19 for the hub bolts. They can easily snap an inch breaker bar 🤢🫣

@simonrawle7885

10 ай бұрын

Try putting a getting you mate to stand on the bar. As you hit the head of the bar with a slege hammer. Socks the nut loose. A big form mat on the wheel to stop damage

As a mechanic (not the armchair sort), with the brake disk retaining bolt the way I do it is to use the impact wrench (as you did), but I put all my body weight through my shoulder behind the impact wrench and press as hard as I can and flick the trigger bit at at a time till it moves, if it doesn't move you will have more chance of snapping the head off the bolt, not good but at least you'll have the disk off and you can deal with the broken bolt...(seems i'd already commented before🤔)

Did you put the faulty gearbox back on that BMW which wouldn't help doing a clutch ?

@themarvelousvlog

9 ай бұрын

Yes we did, indeed. Customer did not have the money at the point in time, in which he agreed that the clutch will not come with warranty/guarantee. We are aware that it’s false economy but it’s not our choice- it’s customer’s choice

Those circlips are always a problem on those

in a previous video, when changed brakes on quasqui what was in the spray bottle, brake cleaner?

@themarvelousvlog

10 ай бұрын

Yhup 🫡

@PandaMobileMechanic

10 ай бұрын

thanks just checking lol @@themarvelousvlog

@themarvelousvlog

10 ай бұрын

@PandaMobileMechanic or is it… 👀👀👀😂

ive been spoiled now i cant/wont do jobs with out my 2 post ramp lol

YES a mask br

its not a cotter pin, that is something completely different, it is a split pin and a castellated nut, this is before nylock nuts

Love your content but the background music is too loud, I want to hear what you are saying.👍

I like brembo brakes it's better, I know the feeling when it comes to taking off brake dise location screws. I use wd40 and hammer to free it off the ratchet, not impact gun,

How do I contact you I need your expertise mate

Bud just want to let you know there are tools out there that you can get, so you don't have to take off the hub next time and you can just push and reinstall the wheel bearing without taking the hub off the car

@themarvelousvlog

10 ай бұрын

I do have that tool but unfortunately i had no choice as it was so seized in place 😭

@craigna3061

10 ай бұрын

There a time saver when they work, I been looking at getting a new one that connects to hydraulic jack to do them

i once had a circlip snap on me at the end, the type with the reverse slits in, from inside a rear brake caliper, this was on my own car so was fighting with it in a vice at 10pm at night in my shed trying to get the thing out as it sits like 3 inch down inside as it was the ring holding the hand brake mech part inside the caliper, did nothing but swear for ages and swore i wont rebuild any more and just replace the caliper instead lol, have you ever had the pins in the mulitipot calipers just refuse to come out? i use a kettle of hot water when it happens to heat the ali caliper up and it works lol

What city you work around mate?are you far of brierley hill?

@themarvelousvlog

10 ай бұрын

Just 45 mins too far unfortunately pal 😭

@sohale745

10 ай бұрын

Can you come to Birmingham?

@TheRazvancristian

10 ай бұрын

@@sohale745 birmingham is not far of me,maybe

Do you come as far as London??

@themarvelousvlog

Ай бұрын

We cover the area mate 😁

Where are you located????

@themarvelousvlog

4 ай бұрын

London, Hertfordshire, East Sussex, Northampton, Basingstoke and surrounding area

Should be wearing safety glasses under a vehicle as get rust in eyes is nasty or dirt

How much do you charge mate ?

I find a product called gas shock works better than wd40 it’s not a plug are any thug like tht just I work on a lot of cars out side my house and you Inspection to the jobs that are acheabul on the flore with no lift nothing just pray for a good days wether respect

Front and rear disk brakes are all ways different

Can l ask a stupid question? Why get you guys out to do work on cars? Why not just a local garage rather than a dealership? Is it cos your mobile hourly rate is cheaper?

@themarvelousvlog

2 күн бұрын

I don’t think that’s the reason to be honest. It’s more convenient to get someone out than taking it out to a garage; or getting it towed there

@dragshampc1286

2 күн бұрын

@@themarvelousvlog ahh ic ty for replying

Whats that at the end of your chin that also doesnt make sense hahahahhaah

@themarvelousvlog

10 ай бұрын

Leave it mate. Us Asians can only grow so much of them alright? 😂

@1970sthrowback

9 ай бұрын

@@themarvelousvlog look on the bright side, youll stay youthful looking for longer 😂

@themarvelousvlog

9 ай бұрын

He be looking 60 and I still be 20 😂

If you think wd40 is good try plusgas that will rack ya brain for breaking off rusty nuts/bolts

Please cut the music when you talking or better still cut it out completely.

E30 rear subframe bushings - hammers, knifes, sawzall, but fire won in the end. Never again polybushes all the way. Nice M4 though.

He isn’t jacking the M4 in proper way, it’ll cause damage to the underside. Ideally need to use scissor lifts for BMWs

@themarvelousvlog

10 ай бұрын

Hmmm… from working at BMW, I think this is perfectly fine… 👀

@tonyrice3348

10 ай бұрын

What if you need to change a wheel at the side of the road? Whip out the old scissor lift from the boot? Did he unscrew the bolts wrong too? There's always one in the comments, every time

@themarvelousvlog

10 ай бұрын

Love to see negative comments, mainly when the person knows everything. *Edit* I didn’t know that jacking it up on the designated jacking point is wrong. I must be going mad 😅 Regardless, I appreciate everyone here 😅😂

Yet again music over powering your description

@themarvelousvlog

10 ай бұрын

Noted 🫡

"works out" but can't undo a bolt 😂

@themarvelousvlog

4 ай бұрын

Hey! Please! 😂😂😂

M4 owner should be ashamed

@themarvelousvlog

10 ай бұрын

Why’s that pal? 🤔

What a plonker of a customer if you dont address your gearbox issue such as bmw gearbox syncromesh which is notorious for going bad on bmws that new clutch wont last even 6 months