Shout-out to everyone watching this over and over again in surveying class

@Turtlefarm

2 жыл бұрын

I’m a construction worker. But plan on being a manager or foreman. So this is key when you Wana move up in the ranks.

It's very helpful for me here in Nigeria

congratulations

Thank you for the video

thanks it helped a lot .... can you provide with any guide book or leaflet where one can learn about total station survey. Thaks again

Thanks sir

Thanks you sir. I'm new and I hope it's will give me a lot experience in future .

@destroyrancho7571

5 жыл бұрын

Sahi kaha bhai

I suggest of a better camera angle while you are doing adjustments.

This thing is still a pain in the ass to setup

Would you not use a plumb bob to accurately place the instrument?

Yes

seldom use theodolite except if you need need a second instrument for observing angular intersection for the purpose of monitoring verticality

The foot screws on the tribrach were some way off the central position before he started. Better to be central so you have equal opportunity for adjustment both ways on each screw. Also when checking the plate bubble, adjust the foot screws in both planes (x and y) to ensure the instrument is positioned level. Nice simple video for beginners.

@santiagoarroyo4687

7 жыл бұрын

yup, the video only showed leveling the plate bubble in one direction, parallel to the 2 foot screws. It should demonstrate as well the turning of the instrument 90 degrees, more or less, and leveling the plate bubble along that second axis using the 3rd foot screw. Then check again through the optical plummet if its crosshair already coincides with the mark on the ground. And if not, release again the instrument's tribrach and move it while aiming for the optical plummet's crosshair to coincide with the mark on the ground. Lock the tribrach up and repeat the leveling process on both directions until you check that the optical plummet's crosshair coincides with the mark.

@ammm__3144

5 жыл бұрын

Oh you need Bobs or veganas

@johntiloshvilli

2 жыл бұрын

Yes, you are correct. You should always start with the screws in the neutral positions. More than that, the screws should have already been in the neutral position when you put it in its case. The above method is for amateurs!(see my comment above).

When using the plate level, you also need to rotate 90 degrees, and level ( with the 3rd screw only), and repeat, until level both ways, and still over the point.

With all due respect, if you worked for me, I wouldn't let you touch a theodolite! I would use you as a rod man. I have been working in surveying for more than fifty years(yes, I am old) and am still working. No self-respecting instrument man would set up like this. First, we use a light weight plumb bob while setting the tripod for rough centering(the tripod should have a plum bob clip to hand the plum bob). Then we level the instrument COMPLETELY, otherwise it would be folly to use the optical plummet. The instrument must be leveled in BOTH directions, not just one as you did. Then we use the optical plummet for fine adjustment over the point. Then we level again and check again. Usually, that is enough. The entire process should take no more than half a minute or so. People on the job don't want to wait around while you fiddle. I will give you credit in that this seems to be the inane method currently taught to unsuspecting students. By the way, fifty years ago we used steel circle transits with no optical plummet, just a heavy plum bob. I could set up perfectly in around thirty seconds(even in the wind). The world record was around ten seconds!(Yes, there were competitions!). So, let's stop using this "modern" insane method and use what professionals use: a plumb bob for the rough setup.

@jordzzzzzzz

2 жыл бұрын

Only noobs need a plumb bob for rough set up!!

@MrJbxl88

Жыл бұрын

I usually use a dot lazer it's a little bit faster for me to center the legs. And I use a torpedo to get the legs level before I even put on the theodolite.

@happyjack8952

Жыл бұрын

A plum bob, is that like an apple bob ?, bobbing for apples, that is.

Are all digital theodolites as simple as this one? What make and model is it?

@InvadersDie

6 жыл бұрын

topcon DT-200

@Elfin4

5 жыл бұрын

You can also get "Total Stations" they record measurements on site and download the site measurements.

You wanna save a bunch of time...???? Set up over the pin looking through the down periscope. Don't even think about touching the screws yet. The bullseye bubble is just to get you close the critical vial is what you want to be gospel when you can spin it round & the long vial(critical vial) Remains spot on level through 360,780 etc are you ready to go but we're not there yet. Next use the legs to get level w/the bubble just fast & dirty. Check down scope for set up move if necessary. If you start turning dials @ this point it will move far from its mark & you'll be repositioning it all damn day. After leg leveling & the bubble seems to stay in its circle your still not there if the critical vile isn't spot on through rotation but real close now use the dials for fine tuning & last positioning. & when leveling 1 leg & 1 dial you should never move. It's on 3 legs & has 3 dials use two legs to level up to one leg and two dials to level up to the dial that was over the stationary leg. I'm no professor at this just years behind one laying out commercial buildings as a carpenter. When everybody's screaming for layout lines on the site time needs to be saved without throwing down dirty layout or a busted grid. Layout personnel need time backcheck their work or it's gonna be the curly shuffle

@firstlast-bz5bq

6 жыл бұрын

Bill, agree, however, a plumb bob and a torpedo level ( high quality) is better. this allows one to center over pin and level top of tripod. saving tons of time.

A quick question, if you know the answer... I have a theodolite with a laser plummet. However, the tripod has a plumb bob hook inside the tripod screw. This works well for when I attach a plumb bob. However, this interferes with the laser dot which becomes quite blurry and poorly defined. What do people do in this situation?

@christophertierney6600

Жыл бұрын

Stupid answer - Can you remove the plumb bob hook from the tripod?

@mathmandrsam

Жыл бұрын

​@@christophertierney6600 Only in the same way that I can swap out my laptop's hard drive for another... (not easily or quickly). In the end I removed the plumb bob hook with the intention of returning it to the tripod screw... but this action certainly damaged it (the way it was attached suggested it was not designed to be removed). A separate tripod screw (with shipping) was almost the same price as a new tripod. So, the solution I have adopted is to have 2 tripods.

@christophertierney6600

Жыл бұрын

@@mathmandrsam Some lessons are expensive ones. Silver lining is having a second tripod?

@mathmandrsam

Жыл бұрын

@@christophertierney6600 I wasn't too worried about the price. Bonus was that the theodolite was new but old stock (still sealed) and I got it 50% off retail. So swings and roundabouts.

i guess what he could have done wrong is doing the leveling out of order

I do not understand??? This process was taught in class as well. I highly disagree. A torpedo level and plumb bob is required. Correct process. 1. extend legs and place level on top of tripod, and level 2. hang plumb bob and move over pin 3. recheck plumb bob level 4. connect Theodolite and check level and pin The problem with the way which is shown in the video is that the base for the theodolite is not level. So when our engineer in the video used the plumb sight to get over the pin, he was still off with his levelness of the base, which is a big issue. Time, it is a waste of time. efficiency is required. I argued with my classmates about this and they disagreed. However, they are wrong, this video is wrong, and I am correct. I know that my way is correct. Furthermore, when our engineer slides the theodolite to center over the pin, his levelness will be thrown off, because his base is not what? correct, is not level. thus this videos process is just fighting a losing battle. I am a bricklayer and this is how any bricklayer would perform this task. thanks.

@michaelbailey4442

4 жыл бұрын

If you start with an instrument that's pretty close to zeroed, you can eyeball the top of the tripod level. The leveling screws got plenty of stroke you don't need to fuck with the torpedo . It's redundant. You're going to have to use the leveling knobs anyway.

he's doing this ass backwards, I would sequence this differently

@OhJeezRanders

3 жыл бұрын

Can you send me a video of how you would do it then?

@JohnSmith-fe2pz

3 жыл бұрын

I believe so too. Taking alittle too long to set up.

Is it possible to get a transcript of these videos? Dave's speech impediment makes it a little difficult to understand what he says sometimes, and I'm rewinding and replaying the video over and over to try and decipher it. Very confusing.

need to work on setting things up. there are better methods than whats shown here

@firstlast-bz5bq

6 жыл бұрын

I agree, like using a torpedo level and plumb bob.

WE NEED WOMEN SURVEYORS

@awalmusaejigebe6215

6 жыл бұрын

Jamesbrown Isdead can I do my industrial training with you

@hannahwambui7204

6 жыл бұрын

We are here

@Warpig9

5 жыл бұрын

WE NEED WOMEN SANITATION WORKERS!

@jordzzzzzzz

2 жыл бұрын

WE NEED MORE WOMEN MAKING MORE SANDWICHES!!!

This is so outdated....

Please dont try to learn the correct method from this video.