I'm so glad these videos are still available, I have a 08 Vegas Low and a Vision 2013.
@montanaairframer23 күн бұрын
Great video! Both my 2016 Vision and 2016 Magnum needed new fuel pumps under 10,000 miles. I bought them used and the previous owners didn't ride them and let them sit with ethanolated fuel in the tank for extended periods. Filter degraded and the pump sucked in the crap. Not Victory's fault but cured my issues.
@kalipramod91018 жыл бұрын
Thank you Rylan!! .Great Video, i appreciate your time and effort. Very helpful, specially simple procedure like starting in cold weather.
@matthewwalker64958 жыл бұрын
This is an excellent video! great job. I would like to see upgrade videos like this.
@nickheinz37377 жыл бұрын
Great Video, nice of you to share the differences in generations of the Victory. I am a long time BMW rider that purchased a Cross Country Tour. Thanks
@mjmigler6 жыл бұрын
I just picked up a pre owned Gunner and these guys explained a lot (nothing needed yet other than oil change). Excellent video.
@waterboy7505 ай бұрын
Guys, you just put my mind at ease on several questions I had on my 2014 CC. Thank you and i hope to make it to the shop if its still open someday!
@Outchillify8 жыл бұрын
For me as a driver in Germany a great and useful video. Just as all of your videos. Until my dealer there are 110 kilometers. And victory workshops there are not many. Until now I never had problems with my 2014 Hammer 8 Ball, but I'm glad about every piece of information that can help me if what should be.
@ZebraActual3 жыл бұрын
Great video! I just got my virtually BRAND NEW 2016 Victory Hammer S a few days ago and have already put almost 450 miles on it.. nice to have a resource like your videos available! Hopefully i won't have a no start issue for a long long time.. *fingers crossed* lol
@gmktng9 жыл бұрын
Great video -- the content is extremely useful and the production values are very strong. Rylan does terrific work. He put an '05 engine and transmission into my 2000 Sport Cruiser and has done other work on my bike as well.
@usethenoodle
2 жыл бұрын
He did Torque Tubes, Lloyds Timing Wheel, Power Commander and dyno on my 13 Vegas in 2015. He's an awesome guy and my bike still runs perfectly in 2021.
@BillyGlock7 жыл бұрын
Thank you Rylan and Gabe!! Great Video, I and many really appreciate your time and extra effort to help us with our Vic's. I have called you a few times with dumb newbie questions..... you are always patient and very helpful... That means a lot... So after 60,000 miles, when I needed Professional help on my 12 year old sick Vic, without hesitation I trailered my VIC 300+ miles to Desoto Iowa, to your VIC shop... You guys are great! Thanks again!
@usethenoodle
2 жыл бұрын
I trailered my 2013 Vegas to his shop from Tacoma, WA. He does great work and is a really nice person.
@TynnMan953 жыл бұрын
Just picked up a 2014 Highball. Great videos guys!
@dennisherreid53933 жыл бұрын
Excellent video! Clear and concise. Thank you!
@mikesutherland59823 жыл бұрын
Living in Canada and with colder weather at times I would have to agree 100% with the little throttle and preach to all who will listen. Mike
@MTL_Rider2 жыл бұрын
Just about to but a Victory and this is best informative video on items to look for. Thanks
@2bigvtwins6 жыл бұрын
What a great video and very INFORMATIVE video - good job !
@brewers-country89035 жыл бұрын
Awesome video guys. Us Victory people appreciate these videos!!
@maurogallegos86948 жыл бұрын
Thank you guys it is very well made and informative video.... I like to know an easy way to change the air filter on my 2012 Cross country tour, this time i would like to do it myself.
@Ben-gy4cx6 жыл бұрын
Excellent video! Nicely done. I am a proud owner of my first bike, a 2011 Victory Cross Roads :) I wish I had your shop a lil closer to home tho, I'm from Ontario Canada.
@Homeward2019
4 ай бұрын
Are you still happy with your bike? I have a CCT 2015 and have put 8000 miles on it in the last 8 months.
@ericb4127 Жыл бұрын
Thank you very much for this video I just bought a 2008 vision with 8500 on it. When it's cold, it seems to lope like a Harley. And when I'm driving, sometimes it seems like it's bogging down, it might be the Intake boots you mentioned.
@garyshaw31125 жыл бұрын
Great video guys as a new Vic owner the info is helpful
@colbywallace111 Жыл бұрын
Just bought a 2010 hammer 8 ball today couldn't be happier
@jkl70976 жыл бұрын
Thank you. Alot of information presented in a short video.
@jamesparsons31348 жыл бұрын
The video was very helpful, thank you so much.. keep up the good work....
@KKlobuznik7 жыл бұрын
Great video. Thank you for sharing it with us...
@user-tn7ew2fx1d9 жыл бұрын
Great video, just what I was asking for. Thank you. Too bad this video didn’t come out 3 weeks ago, LOL. My engine and dash would cut out sporadically, took bike to dealer….turned out to be circuit beaker problem.
@freedomon2s
3 жыл бұрын
I've experienced the same, turned out to be loose battery connection. These bike really do shake loose the battery.
@Gooddog18 жыл бұрын
great job guys, proud owner of 2014 Victory Jackpot.
@nassau409 жыл бұрын
Great Video, I always look forward to your next video
@kymmoulds8 жыл бұрын
An absolutely great video. I have a 2014 XCT and there were things there that I didn't know. Well explained in simple terms (for me that was great) and very clear all round. Well done guys. Cheers Kym
@robhicks69456 жыл бұрын
Great tips. Thanks Vic Shop!
@abdurraheemmurray69673 жыл бұрын
Thanks for this video, just what I was looking for!!!
@robertcleveland80928 жыл бұрын
Thanks Rylan ! l appreciate you redirecting me. l forgot that l had seen this tutorial.
@shotgunscott3 жыл бұрын
So helpful with great advice.
@jeffpalmer550211 ай бұрын
Popping at Idle, found a split idle air valve hose. Ordered new valve and hoses. Any vids on replacing that? Yeah i short bumped the starter last winter. Duh me. New sprag and starter clutch. Ditto on the warm up! My 2013 turned 97k last week. After I fix the IAV should hit 100k by winter. Thanks for the vid! Ride on Raylan!🍻
@rstevens26168 жыл бұрын
.. wish you guys would do a tutorial on the drive belt tighten and adjustment, especially the adjustment to center the belt on the pulleys which is next to impossible to achieve. Thanks for the great videos.
@gregmarshall5524
3 жыл бұрын
kzread.info/dash/bejne/YqaOsKuuia-opqw.html
@tommclay7002 жыл бұрын
Thank you, I enjoyed the video and it was very helpful.
@stevenengle64077 жыл бұрын
Excellent video, Thanks!
@therambler00015 жыл бұрын
Love these videos, could you make a tutorial of fuild exchange? Along with oil recommendation for engine, and brake fuild.
@tb122699 жыл бұрын
Awesome video! Keep doing them!
@joshjoy25356 жыл бұрын
Cheers lads!! Appreciate the video.
@GregG6282 ай бұрын
Great info, thank you!! 👍👍😎
@DanCashman139 жыл бұрын
Thank you...great video!
@SW-Video8 жыл бұрын
Excellent info Rylan! One question. Is there another Flasher Relay, maybe one from a car, that will work to test the relay under the right sidecover? The Victory one is kinda spendy. I'd like to add one to the tool chest but would rather spend the money on a $5 one.
@modernpilot2337 жыл бұрын
Excellent video and very informative. Keep 'em coming. However, please do away with the dramatic "video lighting" and turn on some shop lights so we can actually see what is being discussed. Thx
@solomyngrundy19688 жыл бұрын
Thanks guys... awesome video
@eq2lead9633 жыл бұрын
Excellent. Thank you!
@jwoods18915 жыл бұрын
Hey guys. I had just bought a 2011 victory vegas 8 ball 6 speed and fell in love with it. I am a auto mechanic by trade but love to tinker with my bikes. Out of all the videos I have watched I must say yours is the most informative. My only question is do the vegas 8 balls have any common issues that I should be aware of? if so, can you do a quick clip on things i should keen and eye out for.
@marilynthorpe58728 жыл бұрын
Thank you well worth looking at !!!
@jean-lucjorland29998 жыл бұрын
Thank you from France.
@llemmon4 жыл бұрын
Thanks for a great video!!
@Rho_ohm7 жыл бұрын
Great video!
@sybcg3 жыл бұрын
Great video!! Thank you!
@jameasun9 жыл бұрын
add to favs, great video!!!
@mickmccluand4677 Жыл бұрын
Bike won't start; "Right.. lets check the flasher unit".
@gillygrylls6 жыл бұрын
Great video. Just purchased a used 2012 hammer 8ball. I did notice while I had the bike running the lo oil notification came on. I had let it run then turned it off to check the oil and replaced the dipstick. That’s when I noticed the Lo oil notification. It never came up before. Just today after I checked the oil dipstick. Is this normal?
@user-en4wu4ov2m Жыл бұрын
Hey thanks for your video, would have any advice on an ABS light, always on?
@jleetrucking26657 жыл бұрын
Good video;The red cross country ; what kind of hand grips are on that bike?
@IanNortonBaldersBikes8 жыл бұрын
Great Vid, Thanks guys
@fastjaw5 жыл бұрын
Great Video....thanks Mate!
@tomgia19648 жыл бұрын
Thank you too bro ,.. Your awsome 👍
@deangelisstudio13 жыл бұрын
Great Vid thanks, what about cleaning the air filter on a Cross bike ?
@Nickfv12 Жыл бұрын
Great video, I have a 2012 highball and it's starting to idle rough once warmed up and stalls when pulling in clutch when coming to a stop. It'll also sometimes get stuck at ~1200rpm idles when stopped. Thought maybe I need to clean the throttle body but the airbox doesn't come off. How can I get to the throttle body?
@jordanpeele53064 жыл бұрын
Great video. Just picked up a 2013 highball. Stock Exhaust has no mufflers and backfires. Other than annoying, can this backfire do any damage?
@dalewetzel7733 жыл бұрын
Rylan and Gabe rule when it comes to Victory motorcycles 👍🏼
@MikeFlysVideo7 жыл бұрын
Wouldn't the relay mentioned in the non start portion be a started relay, not a flasher?
@hamjatjallomybah7402 ай бұрын
What are the repair tools you need to replace the ignition assembly and also to remove the seat to replace the battery?
@s145245s6 жыл бұрын
Great clip you guys, I'm a proud owner of a 2015 Highball.
@mikesutherland59823 жыл бұрын
Is flasher relay same for all models in these years, like say my 08 KP and 13 CCT, Mike
@robertbuehler46194 жыл бұрын
My voltage regulator failed and gave all kinds of weird readings with the volt meter. Took a a lot of looking to figure out that a $40 used part off ebay would have solved a problem that ended up costing my about $500 at the local shop after I put a lot of my own time in.
@jeffmarcanti57193 жыл бұрын
Great video 👍
@zaroaster8348 Жыл бұрын
Hi Rayland the belt drive of my 2009 Vision with 31k squeakes and makes very annoying metal grinding noise in all gears. i took the bike to local Indian shop and mechanice adjsted the belt, maintenance manual suggest to replace the front sperocket and the belt drive after 30k, but new drive belt is very expensive and i can't find a new front pully. Would you say, if i replace them both the squeaking and the annoying grinding noise would go way? I thought to mention that i don't see any visual impairment or blamishes on the existing belt drive of my motorcycle. And the belt is not too tight either. Looking forward for you suggestion. Regards Frank
@waggitnshaggit65923 жыл бұрын
Man you’re good dude thank you
@ryuzakilawleit89042 жыл бұрын
I had a problem fixed in the transmission on this bike and they left the ignition on backwards. now i have to squeeze the clutch together with the ignition button for the motorcycle to start. In addition, the lights that indicated the changes no longer work, I do not see the neutral, sometimes one (R) appears.
@koabarton9 жыл бұрын
Nice vid thanks for the tips.
@jaymcroy96568 жыл бұрын
Great Video ..
@itsallabouttheridekeepingi44494 жыл бұрын
I know it’s been sometime since this video was made , and not sure if you are still around ? I’m from Australia and looking at buying a Victory Judge 2015 model - on some reviews I read they said you could get a 25mm Longer rear shock , my question is is that a OME shock or aftermarket ? and can I tell but one . Thanks Paul
@KataWentos6 жыл бұрын
Thank you! Cheers
@jedediahsmart5695 ай бұрын
I have an issue where my 2013 Boardwalk fuel pump won’t prime. After watching this video, I tired the blinkers and found that when attempting to use them (key on, in run mode, in neutral) the engine relay would buzz. Seems like also need to replace my led flasher relay. What I don’t understand is why the flasher relay affects the main engine relay. Also, the fuel pump will intermittently work, o noticed it would come on sometimes when I pull the clutch. Pretty wild.
@jordanpeele53063 жыл бұрын
Well done sir
@mobgma8 жыл бұрын
great video
@mikelmc25093 жыл бұрын
Hello guys. I have two 2016 gunner with same problem. When I stop the bike in a traffic light the iddle gooes down and engine go off. Sometimes also engine go off when we try to accelerate at first when the traffic light come green. Dealer changed the IAC valve and looks for air leaks in admision and throtle body. No air leaks detected. In mine the diagnosis indicates some trouble codes reffered to IAC valve. After change the IAC the iddle comes more regular and doesn't fall when the engine is on and the bike stoped. But while running the iddle goes down and stoped the engine when I stop in a traffic light for example. On my wife's gunner same problem before and after change the IAC, iddle fall and stops engine when you are gong to stop the bike while running. On my wife's bike no trouble codes before change the IAC. Two bikes out of warranty period. Could you help me please...?
@codywall70623 күн бұрын
Anything on replacing fuel pump on 2013 highball? I’m not hearing it cycle when I turn the key on and I’m just cranking. Fuse also looks fine.
@jaepark754 жыл бұрын
Vicbuilder (The Vic Shop). Have a question, I have a 2008 Victory Vegas 8 Ball. Haven't rode since early last year, just changed the battery, went to turn the bike on, the fuel injector won't stop running. Bike won't start. Do you have any advise?
@konrad71162 жыл бұрын
Hey. Thanks for great video But i have problem with my Octane 2017 .My victory octane takes about 3x for it to start which it drains my battery. all the octane on forums have the same issue a starter problem,how can I check my starter when it eventually starts after 3rd try only has 3500miles and it's getting worse before one or twice now cold or hot the bike won't start only after 3rd try. Some sugestion ? Please help !!!
@FrancoNepomuceno3 жыл бұрын
i wonder if they are still servicing Vics....now that's its gone...
@rodrigocardenas59165 жыл бұрын
excelente video, en México es muy complicado encontrar algún mecánico que sepa arreglarlas. Saludos Rylan!!!
@edgargastelum8163
Жыл бұрын
How can I charge the battery in my 2011?
@alexpena6948 Жыл бұрын
I just saw this Chanel I live in Corcoran ca do you have a shop near by that you could recommend I’m at 25,000 miles and starting to have trouble with it
@mitchallen58192 жыл бұрын
Where can I find parts for my vegas 8 ball? Polaris doesn't really have anything.
@monkevil9262 Жыл бұрын
my brother as a 2015 vegas 8 that keeps over heating any suggestions not much maint info on victory
@lloydpope40855 жыл бұрын
can you add drive belt adjustment to this video
@JrgsGrgАй бұрын
Are Victorys assembled with metric size bolts and nuts?
@allenmcknight66843 жыл бұрын
Nice video
@sidestudios855 ай бұрын
I got a 07 kingpin but when I bought it, it wouldn't idle but run now I got it to not idle and it runs but backfires, I need to replace the throttle boot but I don't have a high idle lever
@jonnyphoenix183 Жыл бұрын
Why would the flasher module have anything to do with the bike not running?
@mikeviera1447 Жыл бұрын
Question my 2015 cross country shut off while riding and didn't want to restart almost like it lost fuel. So I completely shut down the bike a couple of times and after about 15 seconds it started back up. What could possibly be causing that random problem? The bike only has 16k
@mafe16232 жыл бұрын
My Cross Country would not start and I discovered that the tip over sensor had come loose. Needed to replace and secure in upright position.
@ellkir15214 жыл бұрын
Great job on the video. Just bought my 2015 Vegas 8 ball two days ago. I'm a newbe to Victory and love the bike so far. Just can't figure out why so much smoke when I start it and why the it sounds like a valve knock at idle. The bike runs strong with good 160 compression and only 17k miles on it. Stethoscope has the noise on number two top end tappets. Is that a lifter issue? I would think the idle would be bad if that was the case. Looked like the guy never changed his oil.
@bluerider7922
Жыл бұрын
Just bought a '99 Standard Cruiser (11,800 miles) and did an oil change. Fairly black oil and a Polaris filter - now wondering if it was factory oil and filter and never changed either. (Could be that previous owner bought a Polaris filter)
@Robert-007682 жыл бұрын
Wouldn't the 08 Vegas 8-ball fall into the 2nd group as it was still the 100 cub in engine?
@morgana54622 ай бұрын
I have a 2011 Cross Country starts and runs good but when engine is hot it will die when you stop at light and have to restart any thoughts on this issue
@bjh05273 жыл бұрын
Hey I have aXC and the Cruise Control turns on but I can not set it. Anything I can check before I take to dealer? Great Video by the way.
Пікірлер: 138
I'm so glad these videos are still available, I have a 08 Vegas Low and a Vision 2013.
Great video! Both my 2016 Vision and 2016 Magnum needed new fuel pumps under 10,000 miles. I bought them used and the previous owners didn't ride them and let them sit with ethanolated fuel in the tank for extended periods. Filter degraded and the pump sucked in the crap. Not Victory's fault but cured my issues.
Thank you Rylan!! .Great Video, i appreciate your time and effort. Very helpful, specially simple procedure like starting in cold weather.
This is an excellent video! great job. I would like to see upgrade videos like this.
Great Video, nice of you to share the differences in generations of the Victory. I am a long time BMW rider that purchased a Cross Country Tour. Thanks
I just picked up a pre owned Gunner and these guys explained a lot (nothing needed yet other than oil change). Excellent video.
Guys, you just put my mind at ease on several questions I had on my 2014 CC. Thank you and i hope to make it to the shop if its still open someday!
For me as a driver in Germany a great and useful video. Just as all of your videos. Until my dealer there are 110 kilometers. And victory workshops there are not many. Until now I never had problems with my 2014 Hammer 8 Ball, but I'm glad about every piece of information that can help me if what should be.
Great video! I just got my virtually BRAND NEW 2016 Victory Hammer S a few days ago and have already put almost 450 miles on it.. nice to have a resource like your videos available! Hopefully i won't have a no start issue for a long long time.. *fingers crossed* lol
Great video -- the content is extremely useful and the production values are very strong. Rylan does terrific work. He put an '05 engine and transmission into my 2000 Sport Cruiser and has done other work on my bike as well.
@usethenoodle
2 жыл бұрын
He did Torque Tubes, Lloyds Timing Wheel, Power Commander and dyno on my 13 Vegas in 2015. He's an awesome guy and my bike still runs perfectly in 2021.
Thank you Rylan and Gabe!! Great Video, I and many really appreciate your time and extra effort to help us with our Vic's. I have called you a few times with dumb newbie questions..... you are always patient and very helpful... That means a lot... So after 60,000 miles, when I needed Professional help on my 12 year old sick Vic, without hesitation I trailered my VIC 300+ miles to Desoto Iowa, to your VIC shop... You guys are great! Thanks again!
@usethenoodle
2 жыл бұрын
I trailered my 2013 Vegas to his shop from Tacoma, WA. He does great work and is a really nice person.
Just picked up a 2014 Highball. Great videos guys!
Excellent video! Clear and concise. Thank you!
Living in Canada and with colder weather at times I would have to agree 100% with the little throttle and preach to all who will listen. Mike
Just about to but a Victory and this is best informative video on items to look for. Thanks
What a great video and very INFORMATIVE video - good job !
Awesome video guys. Us Victory people appreciate these videos!!
Thank you guys it is very well made and informative video.... I like to know an easy way to change the air filter on my 2012 Cross country tour, this time i would like to do it myself.
Excellent video! Nicely done. I am a proud owner of my first bike, a 2011 Victory Cross Roads :) I wish I had your shop a lil closer to home tho, I'm from Ontario Canada.
@Homeward2019
4 ай бұрын
Are you still happy with your bike? I have a CCT 2015 and have put 8000 miles on it in the last 8 months.
Thank you very much for this video I just bought a 2008 vision with 8500 on it. When it's cold, it seems to lope like a Harley. And when I'm driving, sometimes it seems like it's bogging down, it might be the Intake boots you mentioned.
Great video guys as a new Vic owner the info is helpful
Just bought a 2010 hammer 8 ball today couldn't be happier
Thank you. Alot of information presented in a short video.
The video was very helpful, thank you so much.. keep up the good work....
Great video. Thank you for sharing it with us...
Great video, just what I was asking for. Thank you. Too bad this video didn’t come out 3 weeks ago, LOL. My engine and dash would cut out sporadically, took bike to dealer….turned out to be circuit beaker problem.
@freedomon2s
3 жыл бұрын
I've experienced the same, turned out to be loose battery connection. These bike really do shake loose the battery.
great job guys, proud owner of 2014 Victory Jackpot.
Great Video, I always look forward to your next video
An absolutely great video. I have a 2014 XCT and there were things there that I didn't know. Well explained in simple terms (for me that was great) and very clear all round. Well done guys. Cheers Kym
Great tips. Thanks Vic Shop!
Thanks for this video, just what I was looking for!!!
Thanks Rylan ! l appreciate you redirecting me. l forgot that l had seen this tutorial.
So helpful with great advice.
Popping at Idle, found a split idle air valve hose. Ordered new valve and hoses. Any vids on replacing that? Yeah i short bumped the starter last winter. Duh me. New sprag and starter clutch. Ditto on the warm up! My 2013 turned 97k last week. After I fix the IAV should hit 100k by winter. Thanks for the vid! Ride on Raylan!🍻
.. wish you guys would do a tutorial on the drive belt tighten and adjustment, especially the adjustment to center the belt on the pulleys which is next to impossible to achieve. Thanks for the great videos.
@gregmarshall5524
3 жыл бұрын
kzread.info/dash/bejne/YqaOsKuuia-opqw.html
Thank you, I enjoyed the video and it was very helpful.
Excellent video, Thanks!
Love these videos, could you make a tutorial of fuild exchange? Along with oil recommendation for engine, and brake fuild.
Awesome video! Keep doing them!
Cheers lads!! Appreciate the video.
Great info, thank you!! 👍👍😎
Thank you...great video!
Excellent info Rylan! One question. Is there another Flasher Relay, maybe one from a car, that will work to test the relay under the right sidecover? The Victory one is kinda spendy. I'd like to add one to the tool chest but would rather spend the money on a $5 one.
Excellent video and very informative. Keep 'em coming. However, please do away with the dramatic "video lighting" and turn on some shop lights so we can actually see what is being discussed. Thx
Thanks guys... awesome video
Excellent. Thank you!
Hey guys. I had just bought a 2011 victory vegas 8 ball 6 speed and fell in love with it. I am a auto mechanic by trade but love to tinker with my bikes. Out of all the videos I have watched I must say yours is the most informative. My only question is do the vegas 8 balls have any common issues that I should be aware of? if so, can you do a quick clip on things i should keen and eye out for.
Thank you well worth looking at !!!
Thank you from France.
Thanks for a great video!!
Great video!
Great video!! Thank you!
add to favs, great video!!!
Bike won't start; "Right.. lets check the flasher unit".
Great video. Just purchased a used 2012 hammer 8ball. I did notice while I had the bike running the lo oil notification came on. I had let it run then turned it off to check the oil and replaced the dipstick. That’s when I noticed the Lo oil notification. It never came up before. Just today after I checked the oil dipstick. Is this normal?
Hey thanks for your video, would have any advice on an ABS light, always on?
Good video;The red cross country ; what kind of hand grips are on that bike?
Great Vid, Thanks guys
Great Video....thanks Mate!
Thank you too bro ,.. Your awsome 👍
Great Vid thanks, what about cleaning the air filter on a Cross bike ?
Great video, I have a 2012 highball and it's starting to idle rough once warmed up and stalls when pulling in clutch when coming to a stop. It'll also sometimes get stuck at ~1200rpm idles when stopped. Thought maybe I need to clean the throttle body but the airbox doesn't come off. How can I get to the throttle body?
Great video. Just picked up a 2013 highball. Stock Exhaust has no mufflers and backfires. Other than annoying, can this backfire do any damage?
Rylan and Gabe rule when it comes to Victory motorcycles 👍🏼
Wouldn't the relay mentioned in the non start portion be a started relay, not a flasher?
What are the repair tools you need to replace the ignition assembly and also to remove the seat to replace the battery?
Great clip you guys, I'm a proud owner of a 2015 Highball.
Is flasher relay same for all models in these years, like say my 08 KP and 13 CCT, Mike
My voltage regulator failed and gave all kinds of weird readings with the volt meter. Took a a lot of looking to figure out that a $40 used part off ebay would have solved a problem that ended up costing my about $500 at the local shop after I put a lot of my own time in.
Great video 👍
Hi Rayland the belt drive of my 2009 Vision with 31k squeakes and makes very annoying metal grinding noise in all gears. i took the bike to local Indian shop and mechanice adjsted the belt, maintenance manual suggest to replace the front sperocket and the belt drive after 30k, but new drive belt is very expensive and i can't find a new front pully. Would you say, if i replace them both the squeaking and the annoying grinding noise would go way? I thought to mention that i don't see any visual impairment or blamishes on the existing belt drive of my motorcycle. And the belt is not too tight either. Looking forward for you suggestion. Regards Frank
Man you’re good dude thank you
I had a problem fixed in the transmission on this bike and they left the ignition on backwards. now i have to squeeze the clutch together with the ignition button for the motorcycle to start. In addition, the lights that indicated the changes no longer work, I do not see the neutral, sometimes one (R) appears.
Nice vid thanks for the tips.
Great Video ..
I know it’s been sometime since this video was made , and not sure if you are still around ? I’m from Australia and looking at buying a Victory Judge 2015 model - on some reviews I read they said you could get a 25mm Longer rear shock , my question is is that a OME shock or aftermarket ? and can I tell but one . Thanks Paul
Thank you! Cheers
I have an issue where my 2013 Boardwalk fuel pump won’t prime. After watching this video, I tired the blinkers and found that when attempting to use them (key on, in run mode, in neutral) the engine relay would buzz. Seems like also need to replace my led flasher relay. What I don’t understand is why the flasher relay affects the main engine relay. Also, the fuel pump will intermittently work, o noticed it would come on sometimes when I pull the clutch. Pretty wild.
Well done sir
great video
Hello guys. I have two 2016 gunner with same problem. When I stop the bike in a traffic light the iddle gooes down and engine go off. Sometimes also engine go off when we try to accelerate at first when the traffic light come green. Dealer changed the IAC valve and looks for air leaks in admision and throtle body. No air leaks detected. In mine the diagnosis indicates some trouble codes reffered to IAC valve. After change the IAC the iddle comes more regular and doesn't fall when the engine is on and the bike stoped. But while running the iddle goes down and stoped the engine when I stop in a traffic light for example. On my wife's gunner same problem before and after change the IAC, iddle fall and stops engine when you are gong to stop the bike while running. On my wife's bike no trouble codes before change the IAC. Two bikes out of warranty period. Could you help me please...?
Anything on replacing fuel pump on 2013 highball? I’m not hearing it cycle when I turn the key on and I’m just cranking. Fuse also looks fine.
Vicbuilder (The Vic Shop). Have a question, I have a 2008 Victory Vegas 8 Ball. Haven't rode since early last year, just changed the battery, went to turn the bike on, the fuel injector won't stop running. Bike won't start. Do you have any advise?
Hey. Thanks for great video But i have problem with my Octane 2017 .My victory octane takes about 3x for it to start which it drains my battery. all the octane on forums have the same issue a starter problem,how can I check my starter when it eventually starts after 3rd try only has 3500miles and it's getting worse before one or twice now cold or hot the bike won't start only after 3rd try. Some sugestion ? Please help !!!
i wonder if they are still servicing Vics....now that's its gone...
excelente video, en México es muy complicado encontrar algún mecánico que sepa arreglarlas. Saludos Rylan!!!
@edgargastelum8163
Жыл бұрын
How can I charge the battery in my 2011?
I just saw this Chanel I live in Corcoran ca do you have a shop near by that you could recommend I’m at 25,000 miles and starting to have trouble with it
Where can I find parts for my vegas 8 ball? Polaris doesn't really have anything.
my brother as a 2015 vegas 8 that keeps over heating any suggestions not much maint info on victory
can you add drive belt adjustment to this video
Are Victorys assembled with metric size bolts and nuts?
Nice video
I got a 07 kingpin but when I bought it, it wouldn't idle but run now I got it to not idle and it runs but backfires, I need to replace the throttle boot but I don't have a high idle lever
Why would the flasher module have anything to do with the bike not running?
Question my 2015 cross country shut off while riding and didn't want to restart almost like it lost fuel. So I completely shut down the bike a couple of times and after about 15 seconds it started back up. What could possibly be causing that random problem? The bike only has 16k
My Cross Country would not start and I discovered that the tip over sensor had come loose. Needed to replace and secure in upright position.
Great job on the video. Just bought my 2015 Vegas 8 ball two days ago. I'm a newbe to Victory and love the bike so far. Just can't figure out why so much smoke when I start it and why the it sounds like a valve knock at idle. The bike runs strong with good 160 compression and only 17k miles on it. Stethoscope has the noise on number two top end tappets. Is that a lifter issue? I would think the idle would be bad if that was the case. Looked like the guy never changed his oil.
@bluerider7922
Жыл бұрын
Just bought a '99 Standard Cruiser (11,800 miles) and did an oil change. Fairly black oil and a Polaris filter - now wondering if it was factory oil and filter and never changed either. (Could be that previous owner bought a Polaris filter)
Wouldn't the 08 Vegas 8-ball fall into the 2nd group as it was still the 100 cub in engine?
I have a 2011 Cross Country starts and runs good but when engine is hot it will die when you stop at light and have to restart any thoughts on this issue
Hey I have aXC and the Cruise Control turns on but I can not set it. Anything I can check before I take to dealer? Great Video by the way.