The Ultimate Hi-Lift Off-road Jack for only $60!!!
Build your own off-road jack for a fraction of the cost using a Harbor Freight 3500lbs trailer jack.
#builtnotbought #diy #AGM #ARG #Radflow #KingJack #hydrojack #canam #polaris #sidebyside #sxs #glamis #dumont #racing #welding #tigwelding
Пікірлер: 106
These are such useful jacking units for a pretty low price. I like your mods. As for power lifting, make sure to never use the impact gun on it, the gears will spit their teeth very quickly. I sadly killed 2 very nice old jacks learning the hard way.
@MiahsBug
2 ай бұрын
Really good tip Nathan! Thanks
As I noticed from the comments and your responses regarding the music, and while I personally like the music - reminds me of The B-52s or Oingo Boingo - it is too loud for the video. In just about every video editing software you can control the volume on the individual audio tracks. The best range for music along with video is to reduce the volume -20 to -25db. There is also a thing called audio ducking, to find it for your particular editing system, look it up on YT. It's where the music sound automatically reduces in volume when someone is speaking and then comes back to full volume when not speaking. As for the jack 👍🏼👍🏼👍🏼👍🏼👍🏼! I made one similar from a 5k jack square jack foot 20 years ago to lift my lifted F-350. They work great. Are better than Hi-Lift, and lighter to maneuver.
@MiahsBug
2 ай бұрын
Thank for the feedback. I use CapCut because it’s so fast and easy. I will look and see if they have that feature or I just won’t play music while I talk. Would love to see the one you built. I’m always so intrigued by people’s creations.
Loose the music... and I gota admit, I've never seen anyone weld on wood. I liked the part when you said you can use a cut off wheel and showed a flap disk. ;)
@MiahsBug
2 ай бұрын
Yep, got some feedback on the music, 😊 I’ll fix that. Channel is a work in progress. You haven’t lived until you weld on wood lol. Also flap disk/cutoff wheel fail…yes. Keep the feedback coming!
@autocrossratrod
Ай бұрын
I weld on wood all the time.... but my main shop is a wood shop.
@MiahsBug
Ай бұрын
@@autocrossratrod right on!
@mikehoncho3099
Ай бұрын
Welding on wood gives the work area a more relaxing smell but if you want a little fun weld on cardboard
@MiahsBug
Ай бұрын
@@mikehoncho3099 precisely, I only weld on rich mahogany for the relaxing aroma. 😂
If you want to strip the galvanized/ Zinc coating get some pool acid and set it in a bowl outside. When it quits bubbling rinse with water.
@MiahsBug
2 ай бұрын
Really good tip! I have some of that acid. I will give it a try. Thanks!!!
@MiahsBug
2 ай бұрын
What do you do with the acid when your done? Just water it down?
@norcoredneck
2 ай бұрын
@@MiahsBug yep I save it till it gets ugly then I just pour it and flush with water.
@MiahsBug
2 ай бұрын
@@norcoredneck 🔥💯🔥
Nice build! Great idea👍🏻 For those that don’t wan’t to fabricate.. you can pick up a standard Landrover defender jack for cheaps. Got one for 40$.. it holds 3000lbs/1400kg. I use it directly in the framerails of my Samurai. Only LR thing I trust😄 Cheers from Denmark 🇩🇰
@MiahsBug
2 ай бұрын
Dang that’s a good price! I’ll keep my eye out for one. Cheers 🇺🇸
You should have flipped the base plate upside down so it will dig into ground so it doesn’t slip when you use it off-road.
@MiahsBug
2 ай бұрын
I was thinking of doing that or add some pegs that will grab. Will wanted to use it on concrete as well
@catman1050
Ай бұрын
@@MiahsBug 4 threaded holes. carbide snowmobile studs. remove when on concrete or flooring.
@MiahsBug
Ай бұрын
@catman1050 that’s a good idea!
I love the idea! It's great! I would however, try to move the lift point closer to the vertical section. I think you'd have less issue of it wanting to kick out (which is the scary part of all high lift jacks).
@MiahsBug
2 ай бұрын
I agree. The lift arm should be as short as practical. The articulating foot helps with being able to angle the leg directly under the lift point to reduce the chances of it slipping out
Nicely done!!
@MiahsBug
2 ай бұрын
Thank you! I’m trying the clickbait thumbnail. It’s all about learning lol
Nice work. I came up with one of these a while back to jack up my 55 Chevy by the trailer hitch.
@MiahsBug
Ай бұрын
That’s awesome. Did it work well?
Food for thought on the bottom of the foot, weld some beads across to act as a non-skid verse a slick/slippery foot.
@MiahsBug
2 ай бұрын
I like that idea. Thanks!
I just found you and I am a new subscriber for the Baja bug content. I have been assembling a small machine shop to support my new channel that will be kicked off with a 1928 build of a Morgan Hillclimb Racer. I am going to specialize in pre war race cars and machines as well as equipment.
@MiahsBug
2 ай бұрын
That’s sounds awesome. I’ll throw a sub your way as well sir. Thank you
@johnkoury1116
2 ай бұрын
@@MiahsBug I do not know what I am going to call my channel yet. Where are you located/ I am in Pennsylvania....I am thinking about machines and motors...
@MiahsBug
2 ай бұрын
@@johnkoury1116 “Machine and Motor Co.” sounds cool. I’m in California
@johnkoury1116
2 ай бұрын
@@MiahsBug Thank you!
Interesting , Thank You. A fine idea
@MiahsBug
2 ай бұрын
Glad you liked it!
I have no clue who you are, but you’re getting a sub for the Baja bug content
@MiahsBug
2 ай бұрын
😂 well I’m Miah. Now we know each other! Thanks for the sub. You rock!
Did I spy Smooth Withalowmew!!? 😂 Awesome work sir! Look forward to more!
@MiahsBug
2 ай бұрын
Thanks Aaron. Withalowmew?
Loved this! I am going to make one for my truck and Jeep. Much nicer than my super heavy farm jack.
@MiahsBug
Ай бұрын
Have fun old man. You have other socials so I can see the build?
I like the nice rock-n-roll theme you used to complement this video.
@MiahsBug
Ай бұрын
Rock on CMA. Thanks for the comment!
Ooh, time for an Evolution saw. ;) (I truly despise abrasive cutters.) Yes, do wear gloves and cover bare skin. Skin cancer is no fun, weldors! Nice little jack there.
@MiahsBug
2 ай бұрын
I need one so bad. I hate my saw. It works just not great.
Very nice! Now make me one 😆
@MiahsBug
2 ай бұрын
Deal!
I like the idea. but when I make mine instead of a swivel foot I will weld 4 tabs onto the base and a leg attached with 2 permanent pins in back and 2 removable pins front that let a leg fold up for storage and tabs up higher to insert the pins to lock it in storage mode and lock down that is a bit farther out then the lifting point so it can not tip forward. cons not as good in uneven terrain pro more surface area to lift with.
@MiahsBug
2 ай бұрын
I like it. That should work good. I saw a few versions like that online. 🔥
@charlesflakusj.r6344
2 ай бұрын
@@MiahsBug did you ever see the screw jack that Fireball tools made?
@MiahsBug
2 ай бұрын
@@charlesflakusj.r6344 no I haven’t. I’ll check it out. Thanks
Good lookin jack
@MiahsBug
Ай бұрын
Thanks User-wr1. Good looking user name!
I like it. Subscribed. Was the paint on the jack powder coat?
@MiahsBug
2 ай бұрын
Thanks for the sub! Yes it was. Very nice and thick powder coat. I was impressed.
@SpaceBallOne-fc3ep
Ай бұрын
@@MiahsBug I think I'll give this a whirl. Looks nice.
@MiahsBug
Ай бұрын
Good luck SpaceBall! You got this
I see you are a Harbor Freight guy, as am I so when they start selling a dry-cut 14-inch metal saw, get it. I got a deal on an Evolution steel say and I could cut that tube in about the same time as your time laps.
@MiahsBug
2 ай бұрын
Yes! It’s on my tool list. I actually cut that Timelapse down because the cut sucked so bad. That’s a makita saw blade too.
@jeffwelsh1185
2 ай бұрын
That’s why you take a piece of angle iron and bust up the edge of the cut off abrasive blade. Helps it to cut wuicker
@MiahsBug
2 ай бұрын
@@jeffwelsh1185 is that true? Or you’re joking?
You sir.....are my hero
@MiahsBug
2 ай бұрын
🤣thanks. KZread University is a good school
Take an old tire and cut it up. Use the tire tread for the bottom of your foot and rivet or bolt it on. It adds way more grip and increases safety. I did that to my hi-lift jack and has reduced slippage a lot.
@MiahsBug
Ай бұрын
That’s a great idea! I have a perfect tire for the job!!!!
@saltymethods2637
Ай бұрын
@@MiahsBug where did you source that articulating foot? Looks like a nice one.
@MiahsBug
Ай бұрын
@saltymethods2637 it’s on McmasterCarr. Around $30
@saltymethods2637
Ай бұрын
@@MiahsBug Thanks!
@MiahsBug
Ай бұрын
@saltymethods2637 you’re welcome!
Ask your friend where he got the swivel for base. Perhaps a part number as well. I gave up trying to find one that large.
@MiahsBug
2 ай бұрын
He got it on McMaster-Carr website. PN 6111K64
@MiahsBug
2 ай бұрын
They have lots of options for all kinds of things
@JackSmith-jj3bi
2 ай бұрын
Thanks so much. I bought the same jack for a different project that got tabled. It has been gathering dust for long enough.
@MiahsBug
2 ай бұрын
@@JackSmith-jj3bi good luck Jack!
Is there a reason to include the round tubing and pin? If you had cut that off and welded directly to the c channel, you would have your lifting point closer to the center of the jack so it wouldn't kick out like that, and it would be stronger. Originally I was thinking you would weld one of those rings directly to the vehicle so it could be a lifting point and storage location. Also, turn down the music. It's louder than your talking in a couple places.
@MiahsBug
2 ай бұрын
The only reason we did that is so it can be changed out if needed. You definitely could weld directly to the leg and not use the pin portion. Good idea Kami!
👍With your time and materials what would you sell this jack for?
@MiahsBug
2 ай бұрын
Probably around $300. Took me about 5 hours to build but if I built multiple it would be faster
did you guys ever actually take a tire off with just that jack being used?
@MiahsBug
Ай бұрын
Yes! It’s being used every time the SxS is loaded/unloaded to fit in the trailer. Been used for multiple trips now.
I like your music and editing. High lift jacks are sketchy. The jack you built is a new level of sketch bro. The lifting point is too offset from the base plate. What would have been cool is if you guys welded jack points onto the side by side. Then it would be awesome. This way its just dangerous.
@MiahsBug
22 күн бұрын
Like you said, all high lift jacks are sketchy. Agreed 100%. By adding the articulating foot, we are able to angle the jack and align the center of lift and keep the full contact patch with the ground. With that being said, the jack is for cautious tire changes only.
Just don't use an impact and keep the gear greased.
@MiahsBug
2 ай бұрын
That’s what I hear, impacts are a “no go”
aftermarket hitch for the utv
@MiahsBug
12 күн бұрын
Are you asking if it’s a aftermarket hitch? I’m not sure. The SxS is not mine.
I’m bad about not wearing gloves also. It just sucks having the sun burn after.
@MiahsBug
2 ай бұрын
Yes. I’ve only gotten sunburned twice. I usually only do that for tacks or small beads
Myself wouldn’t have the lifting point out so far from main post, and no swivel base for me. But👍✌️
@MiahsBug
2 ай бұрын
The articulating base helps it stay firmly planted while it’s lifting and changing angle. I 100% agree on the lift point. It should be as short as possible.
Good idea and inexpensive. However, could only watch a few minutes of the video due to the annoying music in the background. Maybe your next video will be better. Good luck to you.
@MiahsBug
Ай бұрын
Thank you. I’m learning the ins and outs of editing. Thanks for your feedback.
I would have loved to watch this but had to leave after almost three minutes because of the overpowering crappy background music stopped me from hearing a word you said.
@MiahsBug
2 ай бұрын
Yep, got lots of feedback on that. It’s a learning process. Next one won’t be like that.
@mrmotofy
2 ай бұрын
@@MiahsBug You'll get hate on the music genre, the music too loud, the music too quiet, the music tempo, so you change it then you'll get hate that it changed...you'll never please everyone. Don't waste your time trying to appease em
@MiahsBug
2 ай бұрын
Thanks Mr. Moto. I agree to some extent. I can’t fix the “crappy” music because I’m going to choose what I like lol. But if they can’t hear me over the music, that’s a problem I can fix.
@mrmotofy
2 ай бұрын
@@MiahsBug Yep gotta monitor levels. Like clips vs your voice. Or Intro/Outro etc Or certain tools etc. Just turn Gain down a lil
@MiahsBug
2 ай бұрын
Thank you sir. And thanks for watching!
Also, really cool idea. Build it, don’t buy it.🎉
@MiahsBug
Ай бұрын
I agree 100%. But if you have more money than time, I guess buying it works too 😂