I like that you don't try to flex nuts and don't gatekeep.

Try putting your old hardpoint saw blade in the oven for an hour or so at 200⁰c/400⁰f then re-sharpen it. Just be sure to take the plastic handle off first so you dont have to deal with an angry spouse.

@RIBill

3 жыл бұрын

You can also just get a set of diamond needle files. I use those to resharpen my curved pruning saws, which are impulse hardened. The teeth WILL get smaller, but I can cut branches and small logs for 10 years instead of 2.

@John-lx8iu

3 жыл бұрын

You can also just grab a cheap torch at the big box store and heat up all the teeth until they start lightly glowing and leave it to air cool (anneal). Some may even choose to place it in some warm sand or even in your oven with it turned off to slow the cooling process & further soften the steel but in most cases this shouldn't be necessary. Keep in mind, depending on the exact steel composition, the teeth may need to be re-tempered after sharpening or you will find that it gets dull really fast. Just don't forget to draw back the temper a little as to not have a brittle blade.

@RIBill

3 жыл бұрын

@@John-lx8iu That doesn't really work. The steel is cheap junk. It ONLY hardens with impulse hardening. You can aneal it but will NEVER get it to hold an edge again because you can't harden it.

@leighchappell

3 жыл бұрын

@@John-lx8iu i see where your going with this but the idea of putting it in the oven is to temper the teeth back from the original hardening process, rather than annealing it and having to harden the steel all over again, so the teeth end up half hardened in a similar fashion to those great vintage saws we all chase. It wont be perfect as the steel isn't necessarily great but it does mean you can re-sharpen your saw and it will stay sharp for a good while.

@grantflippin7808

3 жыл бұрын

@@leighchappell you're just annealing it in the oven, which lets you sharpen it.

I remember a SAWYER near a boatyard in West Cork ,he spent all his time maintaining saws !thanks for the great videos .

As a carpenter who isn't really a woodworker, I think I can say the real advantage of an impulse-hardened saw is that they can comfortably eat the standard array of jobsite grit, and the rigors of life in a work trailer will typically cause catastrophic failure or loss before they wear out from extended use anyway, especially considering the small amount of use non-powered saws have in the profession. "Forever" tools have limited utility in a chaotic work environment that involves extended exposure to the elements, dirty storage spaces, and heavy stuff falling over sometimes. They aren't woodworker's saws, they're saws for carpenters or non-professionals. Those two categories make up an overwhelming majority of Home Depot's sale volume, so that's what you see there.

I have minimal interest in woodworking and may never use this information in my life, but your videos are so interesting and entertaining that I watch them anyways. I love what you do man

The best use for an old saw is making it into a panel hacksaw. You'll need a carbide bit and some thread locker. Yes, for the hacksaw blades. Most underrated Cold War era tool ever. Able to cut bedframes or large sheet metal.

I've a few nice Disston handsaws in my till I picked up at various garage sales for about $5 and re-sharpened. Saved the hassle dealing with a tool that was made to be thrown out. -Veteran '66-68

Perfect timing! I was able to find an old saw vise and rehabilitating it now. Thanks Rex!

Oldest anarchy server with deeper grooves at a level 7

@bobbob-vt3bw

3 жыл бұрын

Beautiful

@jake-the-neko5531

3 жыл бұрын

Omg

@yeahman5551

3 жыл бұрын

That's too cursed

@da_og_demonslayer6712

3 жыл бұрын

glass 2B2T?

@BrayGod05

3 жыл бұрын

FitMC has joined the chat

For anyone interested , you could use a torch to anneal the saw teeth on a newer saw allowing it to be sharpened with a regular file

@DavidLindes

10 ай бұрын

I was going to ask about that...

i have sharped a several hard point saws using a diamond thee corner file i bought on ebay

@pentuplove6542

3 жыл бұрын

Thankyou. You answered my question. The saw will still be usable when the superhard metal is gone. Recycle and think.

I gotta say I love this channel from the aspect of entertainment to information to the content being more down to earth for a true newbie. Hopefully I'll be able to be a patron soon. 2020 has not been an enjoyable year but I just wanted to say you are doing an amazing job

If you have a very basic metalworking setup, retired saws can be turned into several things other than just scrapers. The flexibility and high carbon content allow the blades to become decent machetes and filet knives. They can also be used to make fish scales and light duty knives for gardening or food prep

Great saw discussion. I am looking forward to your next video on panel saws!

Rex, let me tell you you have an amazing channel. Your explanations are clear, accurate and you break everything down to simple understandable information. Everytime I get asked how I know so much about woodworking, I recommend your channel (and Paul's) you're an amazing guy.

thanks for an interesting video. You mention a couple of times cutting scrapers out of the disposable saw blade; I think that would be an interesting video too!

@felixdionne-guertin9919

3 жыл бұрын

Pask Makes made a video on that. Super useful tool kzread.info/dash/bejne/mamGr4-hodLPgbw.html

@peethreeorion

3 жыл бұрын

When you make scrapers out of the old blade, don't throw the handle in the trash. Many time, they can be recycled into comfortable and secure handles for tablesaw jigs.

You should do a woodworking with tools sourced only from harbor freight series, I think it would be helpful for those starting off cheap, and amusing to the rest of us.

@cheryliverson6327

3 жыл бұрын

PLEASE, I WAS JUST THINKING THIS. Some of us are using harbor freight tools to start.

I'm blessed to have my house-carpenter great-grandfather's tools, including saws, a saw vise, and the files for sharpening them. Great way to spend an afternoon.

Thank you again Rex. Another very helpful video, well narrated and full of important info. From Vancouver Island - have a great day and stay healthy.

Love your videos btw. Very clear, practical, informative and encouraging. You got me started angle-grinding (restoring tools etc) and just yesterday I turned an old guitar strap into a strop on my sharpening station (made out of a cabinet door & scraps of ply).

Informative, detailed and low drama. Excellent! 👍

I've collected quite a few old hand saws in the past years...just because...now I know because why! Thanks Rex!

I think it's like anything - these peripheral skills to a hobby (such as woodworkers sharpening saws) are as much or as little of a rabbit hole as you want to make them. There is some pride and enjoyment in a new skill of maintaining old saws coupled with the added startup cost and of course the time investment, or on the other hand you can spend a few bucks every few years on a new saw and focus on the work itself. Always good to have options!

@1pcfred

3 жыл бұрын

You're not going to get a saw that cuts very good for just a few bucks. Maybe $70 or so? On the high end $300 is not out of the question. But even then you're not getting a saw pitched exactly how you may like it to be.

This was a phenomenal one Rex! What a great teaching session! Thank you for sharing your knowledge. This is defiantly information people should pay for! Keep up the awesome work! :)

PRE-WARNING, this comment is long and with a lot of gushing... I must admit I joined as patron more for entertainment value. I will now add support because there is great content and substance to your information. Not saying other episodes weren't good, I feel this is one of your best explanations of a topic that has stymied me. I recently built a chest using all the saws you spoke of. I did rip, resaw, crosscut, and some "tight" joinery, and to me you were spot on. I did learn that "to saw" is a skill I must practice. Your channel is easily my fav and the best money spent. I do wish there was a way to kick-in a little bonus money for episodes I really like as an expression of "bravo"... Now get back to work and surprise me again because those videos don't make themselves.

@RexKrueger

3 жыл бұрын

They sure don't! This is a full-time job and I couldn't do it without your support! Thanks for commenting and letting me know I'm on the right track!

@psiclops521

3 жыл бұрын

If you really want a lesson on sawing, I recommend he KZread channel of Renaissance Woodworking. That guy has some videos that are amazing and he is the finest sawyer I have seen on KZread. I like Rex here, but RWw is really a sawyer of distinction.

@ddaa6721

3 жыл бұрын

@@psiclops521 Great tip (this is D Colorado on my son's phone). I checked it out and I enjoyed it. I like different sources to get good info. Some I like are Paul Sellers, Richard Maguire (English Woodworker), Pask Makes, and a Japanese channel. Each are different and each is entertaining. It's all good.

@peterfitzpatrick7032

3 жыл бұрын

D Colorado ... I have no problem with reading long comments ... but .. paragraphs are our friends & make for easier reading .. ... just sayin 🙄

@dcolorado7483

3 жыл бұрын

Good point. I just got a little carried away. I'm new to reading and writing to these youtube reply things. This is pretty much the first place I felt I thought to say anything as it's good stuff.

Great video Rex. At our men's shed, we have a lot of tools given to us from deceased estates. Amongst them are the saws you mention. When they become dull we do not throw them away. We turn them into cabinet scrapers. We just cut the blade into manageable sizes and then go through the process of turning them into scrapers.

I've watched a few of your videos now and I've just had to subscribe as you have a great way of explaining things and the quality of your videos is high. I'm from the UK and looking at using saws I can sharpen as I inherited all the tools to do the job.

In the U.K. we used quality handsaws for years that we used to sharpen & set .Then the price of the hardened tooth throwaway saws came down in price .So we used them for a couple of weeks ,then for roughing out & finally passed them on to plasterers to use on plasterboard ( Dry wall ) Before I retired the timber yards were giving away 1 free saw with every £100 of timber ordered so we always had loads of them .The old skew backed saws were nice to use when sharp but a pain to keep sharpening .Even if you have to buy hard points they pay for themselves as you use them & cut more efficiently cost.next to nothing ,use them & dump them no more hassle having to sharpen. More beer drinking time .👍

I went down to an old hardware store in the my hood. Been there forever. They had one of those old vintage saws new. Thought I was kidding about wanting it.

Got lucky with my 2 saws, barely used vintage ones just like yours... just had a couple dummies at estate sales/yard sales who didn't know what they had who sold them to me for a dollar each.

You are an absolute wealth of knowledge, not a video of yours I don't learn a handful of stuff

Pulled out my gents saw last week for first time in 30 years to cut a small joint. Very blunt. Time to dig out the saw setting kit I've had for nearly 50 years

Thanks for another great discussion, Rex. You are like a one man America's Test Kitchen for woodworking.

When I started in the trades in the early 1980s, there were at least two options for getting saws sharpened in my home town. One was George Miko, who ran a sharpening business out of his basement. He did hand saws, circular saw blades, and lawnmower blades. He even had the equipment to sharpen reel type mowers. The other was a store that sold landscape equipment like mowers and chain saws and also did sharpening. When I got married and moved to Fairfield I found that the neighborhood had a hardware store that would take your saw and have it sharpened for you. The grinding company would pick up saws once a week, ( I think it was Thursdays) and return the sharpened saws the next week. The price was about what I had paid in Norwalk. I guess the store got a discount because of the volume.

Thank you so much for this video! I just bought a tri-edge and had no idea what to do with it, now I know!

@RexKrueger

3 жыл бұрын

You are so welcome!

This is great! Really liking your down to earth approach to woodworking.

@RexKrueger

3 жыл бұрын

Awesome, thank you!

Thanks Rex! There is a ton of great info in this video.

Awesome video! I spent a lot of time and money figuring out what saws I wanted when I was a beginner, and after lots of searching and testing, I am super happy with my current selection. My Veritas 14 tpi dovetail saw and my gyokucho 240 mm ryoba do more than 90% of all my hand sawing. I’ve got a couple other saws I use a lot less frequently, but I will always recommend those two to anyone getting started, and I’ve heard nothing but good things from everyone who’s tried them in their own shop. Both are great bang for buck, and I’ve never found anything that can outperform them.

legit watched the 11:59 minutes of this video and honestly- it didnt even feel stretched like 90% of the youtube videos do these days. very informatic and well explained. nice job

In the UK we have 'Saw Doctors' you drop your saw off and they sharpen and set it for you, they used to be everywhere but we still have them, you can grind the teeth of an hardened saw.

This video came out at a great time; I’m debating on what type saw I should get. I’m still learning a lot about tools and what I need and what I can hold off for the time being

Very good summation of handsaws.

I thoroughly enjoy your videos and admire your sense of ethics regarding free tools and sponsorships. Kudos to you sir.

@RexKrueger

3 жыл бұрын

Thanks for watching

Two words. Frame saws. Head down to Harbor Freight and pick up a 1/8" and a 1/2" carbon bandsaw blade. Less than 20 bucks. Stop at HomeDepot on the way home and pick up some large common nails and some smaller bright finish nails. Less than 10 bucks. Use the 1/8' to make a turning saw that will beat the hell out of any coping saw you can buy. You'll have enough blade for two or three 12" blades. Use the 1/2" to make a larger turning saw, though you don't really use it to turn, but you could some. It's just made that way to allow for long cuts. See Chines Frame Saw video by John Zhu KZread. He even has one video of making a blade from steel spring shims. Get exactly the teeth you want. Use another piece of the 1/2" to make a shorter smaller joinery saw. Make this one with blade let directly into the wood handles, not turning. Super easy to make this one. Just make sure kerfs to recieve the blade are inline. This will get you going on just about everything for very cheap. Like less than 50 bucks including some nice wood. Almost forgot, get some 1/4" allthread, regular nuts, washers and some wing nuts for easier tensioning. For cheaper or even free tensioning use some twine and a stick. You can also get made frame saw blades from a few places online. Or there are many, many bandsaw blade configurations to choose from. Various TPI's and tooth geometries. You can not be this approach for bang for buck and easy skill building.

@johncoops6897

3 жыл бұрын

Or you can skip ALL that work and just buy the hardpoint saws that you need for the same price. If you want to cut curvey things, also buy a hacksaw frame and put a course metal blade in it.

@dcolorado7483

3 жыл бұрын

Hey, your tip about John Zhu was good. He's someone to follow... I was starting to do the very thing about the blades as you suggested. I had materials for the frames saws (the project looked fun) but I realized my current project was behind schedule (birthday gift). So I'm getting by without the saws. Given my wife gave me a raise on my "woodchuck" project allowance, I'm going to buy blades to simplify the "saw" project. Sometimes I just need to pay retail and move forward.

Saws are a bit of a personal journey for us all and it's great to read so much useful feedback in the comments below. You've built a really likeable community here Rex, and you should be proud. My two cents worth is that I purchased a couple of Japanese folding saws (ryoba and dozuki) a few years ago. They are fantastic, as the handles protect the blade (and the user) meaning that they fit in your tool bag without causing injury. (Hell, in a pinch I've carried one up a ladder in my back pocket!) Mine are the Silky brand, the Wood Boy dozuki and Takeru Boy ryoba, but I'm sure that there are many others as good. (I'll try the diamond file trick mentioned below when the time comes.)

In my country (Philippines), a lot of shops offer sharpening services to a lot of bladed tools for cheap. You can find them almost anywhere that is why most craftsman I know just let those shops sharpen their tools.

Rex- a lot of good ideas there. I just restarted my cabinet/trim shop I made the decision to ditch all my disposable saw (Japanese in my case) and have every thing in my shop user serviceable. It may seem like an odd choice but I went with bow saws for everything except 3 Japanese saws that I know how to sharpen my self. Got the blades in my case from highlandhardware and cut them to the appropriate lengths. I also cut down an old misery whip and made in to a Roubo saw for big resaws. Not for everyone but I think I spent less than $150 for about 8 saws I set up and 1 kerfing plane. Enjoy your channel best of the luck.

THIS VIDEO IS EXACTLY WHAT I NEEDED. Thank you so much. I've been looking at saws recently, because my ryoba saw bent, and I was also looking at spring steel shim stock to make specific saws (I want to build a foot powered band saw, a frame saw a replica of Bridge City's Joint Maker Pro, too). Any information about saws is good information, and that video was really excellent. Thank you so much!

Some great useful information. Thanks.

A very informative video! I used to work next to a carpentry school, and I always wondered why saws kept turning up in their waste skip. I guess this is why! Of course, saws that were too dull to learn carpentry with were just fine for me to cut firewood and junk pieces with, so it was great for me- so many free tools! And speaking of firewood, those guys were really wasteful with the wood they threw away as well. Plenty of their junk and offcuts went into projects of mine...

Fantastic video, Rex! Thanks a lot! 😃 Stay safe there with your family! 🖖😊

Wow I found some panel and tenon saws at thrift stores. I also bought saw blades in bulk on ebay. I have been making saws for friends and it is fun. I have never paid those high prices for a saw. Thank you for the information and video.

During the epidemic we couldn't buy new disposable hard point saws. I particularly needed a 14T for cutting plywood. I bought some diamond needle files and re-sharpened using a three square. Brilliant!

Knowledge is Power! Rex is a legend....

Id be surprised if nobody has mentioned it but spear and jackson do a resharpen-able panel saw. Pretty cheap too.

What I like most about your channel Is the fact you are not sponsored, just your honest opinion. I'm an old carpenter and have been using power tools for most of my work, but I do enjoy the feel of good hand tools on wood when I get the chance. I have fare amount of old hand tool and most of them need a great deal of attention. Might be time for this old guy to get back to the old ways a little more.

@RexKrueger

3 жыл бұрын

I appreciate that!

The interesting part, my grandfather born 1906 was a cabinet maker/ finishing carpenter. From the time I was in school I can remember going up to the wood shop and sharpening the tool. Then he taught me how to use old files and an old saw to make other tools. I even have a plain that I made that is almost 40 years old now that I made.

not my type of content, but you are awesome. You know what you a talking about, you are highly motivated, love good tools, but also accepts pragmatic decisions. Also the audio is perfect - a bit shop echo, just a little touch. Really nice. High quality lights - offcourse, good light is a necessity for good manual work, but also good video - it does make a difference. Keep it up.

Thank you for this video! Clear explanation of what many of us have forgotten in the realm of Norm Abrams..... as in, if there is a power tool that I could use for a job.....

first time viewer, learned alot of things i didnt know about thank you for the great info

Looking forward to this later

I got a Japanese style pull saw recently and I'm converted, made the cleanest castle joint I've ever made with it going to upgrade to a more expensive one soon my cost about 15 dollars and love it 🙂

Rex, good job.

This was excellent, thanks for taking the time to go through it all! Perhaps you've already covered it in another video, but have you done a video covering files for comparison as they vary in price so much?

I don't know why your videos are not coming in my feed even though I have subscribed to you a long time ago.

Never knew. Very educational!

Two words of advice. 1) after filing, use a stone on each tooth not much just enough to remove the bur. Makes a huge difference in sharpness. 2) if your looking for a good old saw, take a look at vendor booths at a fair or market. People go buy saws and then throw some painting on it thinking its art. I have seen many Disston, linx, Vermont and oldschool Craftsman(when they still used american manufacturers) for sale. Most are being sold for pennies compared to what the saw is worth.

A prime example of lost arts. My father taught me how to sharpen and set the teeth on a handsaw when I was 11, back in 1966. Does not require a vise ( kind of hard to lug one of those around a jobsite ). Nor does it require a special setting tool. Plain old slip joint pliers will do. The specialty tool makes it quicker, but not required. And the way to determine if you have the set correct was to hold the saw cutting edge up and handle up at about 30 degrees to the ground. Place a sewing needle on the teeth and allow the needle to slide down the teeth. Any tooth that is not set properly will cause the needle to jump off. Not difficult once you know what it should look like when sharp. And filing does not require special rig either. Makes it easier, but just a file will work. Just takes practice and a sharp eye.

That collection of sandviks.. wow!

Love the hell out of my Crown tenon saw. Beautiful piece of metal.

@weedeater64

3 жыл бұрын

Too bad it's only 12". Need 14" for a tenon saw.

Great video! I learned a ton.

I sharpened an old vintage saw that was my grandpa's yesterday. I just lightly jointed the teeth with a harbor freight file (freehand) and used a triangle file out of my nicer file set ($30 set). I used a standard vise with a couple of 2x4s working section by section. It's not really that difficult.

My workhorse backsaw came from a cheap Stanley miter box I bought at Lowe's back in the day. It's resharpenable (I've sharpened it a few times in the past few years) and while it has a plastic handle and the back is just a U-shaped piece of steel, I have absolutely no complaints about comfort or performance. I don't even have a place to hang it up - it lives on my bench. Assuming they still make them, that's a cheap route to get a decent quality backsaw that can be resharpened. The last time I saw it at Lowe's (maybe two years ago?) it was $13 and came with a horribly useless plastic miter box. It wouldn't be too hard to make a wooden handle for it or spray-paint the steel back to make it look like a fancy bronze-backed saw, if that's your thing.

I inherited a weird looking set of pliers from my dad I thought may be for plate bending... and looking at this video I suddenly realised it’s a saw set (german style in my case) Thanks Rex!

I really enjoyed this video. I personally love the Idea of buying a Japanese saw, and I have a fairly big project coming up. I'm glad I got to see this video

Upon reviewing this I have a comment. A hammer, fine punch, a bench, coordination, and a good file will get any saw in tip top shape. Otherwise maybe a magnifying glass to inspect your work from time to time. Anything else is a luxury, anyway still an awesome video!

I've successfully sharpened hard point saws with an inexpensive Esi-Lap diamond hone. I took my time and looked at the coloration on each point to make sure I was working to the original angles. The saw cut straight after I'd done the sharpening and is used as my rough saw or the one I lend out. It was a win win situation, if it hadn't worked I'd have just delayed the trip to the scrap metal bin. I cut a lot of particle board (chip board) and OSB and these are really tough on saws so it was good to get another lease of life out of the hard point. Long term you won't get to keep doing this because the hardening is only going to be shallow but I had the time, it was a sunny day and it was pretty theraputic.

THANK YOU!! You’re so good at breaking things down in a digestible way. 👏🏼👏🏼👏🏼 I’ve watched a ton of videos about saws and was still wondering what the deal with the “big box” hardened teeth were. Looks like my Japanese saw purchase was perfect for where I’m at after all! Keep up the excellent work!

@RexKrueger

3 жыл бұрын

You are so welcome!

I picked up a new “tool box” saw for $8 today at Ollie’s. They are good to learn on and good for keeping in the mobile tool kit. Even once you can appreciate a $$$ saw you don’t want it bouncing around in the car.

Great discussion Rex, thanks.

@RexKrueger

3 жыл бұрын

Glad you enjoyed it

I actually love multimaterial (or metal) fine toothed hacksaws to make small cuts that don't need cleaning.

Hi Rex love you channel! But really enjoy where you are coming from with projects and tools. But what I really would is to have a full view of your workshop, I did see a glimpse of other power tools while you were doing another topic awhile back! Cheers

last time I sharpened a saw was about 30 years ago and ever since I have used throw away saw it make more sense. forget the eco side because when I have finished with them I cut them up into scrapers.

Recently I found that Bahco, the Swedish manufacturer launched wood saws with a modern design but with non hard-point filable teeth. I bought a medium size teeth 24” saw. It was cheap great quality and I can file it. It was under 20 dollars in Home Depot. Here is the model. Brand: Bahco Model: Bahco Pc-24-File-U7 fcut Fileable Saw 24In Great tips on how to file my saws. Thanks a lot Rex!!!

@RexKrueger

3 жыл бұрын

I love Bahco stuff. I'm going to buy one today!!!

I have several hands in my shop that my Grandfather handed down to my Dad, ! You can find hand saws on Craig's list in New England for less than you'll pay for the shipping! I have three saws that are wall decorations that were given to me!

I've sharpened the old style hand saws a lot and not a single time I've used a vice. 'Clamp' it between your knees and keep moving it down or up as you go through the teeth. Takes a bit of practice and a small triangular file.

I cut half a forest out with the Japanese saw and it's still terribly sharp, like new. I bought it cause it has a long handle, and I can cut out stick trees with it, and easy old dead tree cutting, old living trees that are sick, or the worst... rose trees. They are really handy and can get anywhere. I used the saw for a month or two before changing to electric saber cutter, and.. it's just sharp. I accidentally cut metal, stone and dirt+sand. No damage.

I got tired of paying shops to sharpen my saws, plus the long wait times, so I just learned to sharpen my own. I can do an ok job, works for me.

A bit of heat on the teeth of the disposable saw softens it just enough that you can file it I have done this in the past!

SHUT UP AND TAKE MY MONEY!!! I've been amateur wood working mostly with power tools for a long time only stumbling on to your channel about a year ago. I've considered building a lot of the stuff you've done and learned a ton about sharpening planer and chisels from you. I had no idea they didn't just come sharp from a big box store and always assumed it was my technique that made them hard to use the way I see others use them (which is why I typically stick to power tools). I started sharpening chisels after seeing one of your videos and the difference is night and day. You do awesome work Rex. I just bought a new house that comes with a two car garage, that my wife thinks for parking cars or something, you bet your @$$ I'll be buying some plans.

@WarrickTaylor

3 жыл бұрын

I can never understand why people keep calling it a carshed. I know I certainly never plan to put a car in mine!😎

Regarding western handsaws: there are various brand names made by Flinn/Garlick in Sheffield which are quite nice (Pax, Lynx, Roberts & Lee), but most are a little pricey (100ish). Paul Sellers has an episode about modern Spear and Jacksons which seem to be a good value, but at their current prices they are probably made somewhere in the far east with low cost labour.

@psiclops521

3 жыл бұрын

I like Crown as well. So does Paul Sellers, I think, since I see him use them. For those with money to burn, there's Bad Axe and Blackburn.

I have seen Western saws with the replaceable blades on job sites that I've been on one brand that I remember is bahco so you can get a high quality handle and a hard point saw that just clips in an out of the handle.

@jamesn0va

3 жыл бұрын

Yup i have one. The blade is slightly thicker than the standard 244 pattern. The second fix blade from bahco is something else though. 11 tpi and iv cut through metal (accidental and thin) droped it on bricks and cut through plasteboards and its still sharp after years of use.

Until recently I was using a saw that I didn't realize wasn't sharp and was cutting slower than when it was new. I have purchased inexpensive Stanley back saws that I would replace when I finally realized the one I was using had become s dull that it was taking forever to cut through a 3/4" pine board in a miter box. Therefore I have three of them in various stages of dullness because I didn't know I could resharpen them myself. After recently watching a video from Shawn Graham @ wortheffort about sharpening saws, I sharpened the one I am currently using, while narrowing the kerf so that I now have a thin kerf dovetail saw instead of the thicker kerf crosscut saw that it was. I'm probably going to resharpen the others like they were when they came form the factory since I do more cross cutting than dovetails. Thanks for the video outlining the various saws along with their pros and cons.

You really are passionate about saws :)

Hey Rex! Great video as always, in depth and well researched! I do have a suggestion for future videos: if your camera has an input, you should invest in a small lav mic. It would really improve the audio quality and give you lots of polish for a little cash, haha. Keep up the great content!

I've heard similar advice for a lot of tools. "Buy the cheapo Harbor Freight tools first, and when/if you wear one out or break it, spend real money on the new one". That lets you get a lot of tools for cheap, and only spend money on the ones you need to. Buying cheap saws first seems similar; if you like it and really get into it, you'll wear out the saw and replace it. If it turns out it's not for you, you're out a lot less money.

@BrooksMoses

3 жыл бұрын

That advice sometimes works, but you need something that's good enough quality to be properly functional before it breaks or wears out. A lot of things in the Harbor Freight category aren't that. I've seen woodcarving sets that had 1/32" flats on the sharp ends of the chisels, and I'm also suspecting that a good part of why I find handsawing so difficult is that my inexpensive saws just aren't usably sharpened and set.

I went shopping for a hand saw for ripping boards. I could not find any. As my Skill saw was far far away I checked the grain, marked the board and split it with a hatchet. Then smoothed it to the line with the same small ax. Use what you have to do what you want.

I have used my Dremel tool, to resharpen blades from cheap modern saws, it works greate, after a while I have worn thro the hardening, and I can sharpen it "the old fashion way", I have also made nice wood handels, so they are comfy to use.

Thanks for creating great content!

@RexKrueger

3 жыл бұрын

Glad you enjoy it!

@mjallenuk

3 жыл бұрын

@@RexKrueger One day when I've got some time I'm going to have to dig into some of your fab looking projects!

Hi there Rex. Love you videos mate!! If you are just starting out enjoying the sense of pride and achievement that comes from creating something out of wood PLEASE read this to the end. 55 years plus of woodworking gives me some perspective and for the nit that suggested simply buying a skill saw- well better you keep your comments to yourself and not publicly display you obvious ignorance- dopey! Rex, I take your point, up to a point! Your “way cheaper” old style saws though, are just the opposite in my estimation. You’re overlooking the hidden cost of time spent cleaning, clamping, laboriously filing and finally setting; with the ever present risk of breaking a point! Never mind the hidden time in the learning curve! As you pointed out, cost of the clamp (or time making one), files, (which are often difficult to get due to much lower demand) and the setting tool- all add up to a fair investment and you normally don’t wish to carry them all around. I charge $45 an hour for my skills. That is considered low by local standards. To properly sharpen and very carefully set, my beautiful 40 yr old Nicholson 14 point panel saw, takes me an hour or more. A Bahco, 14/inch, hard point, at $14, will cut cleaner and easily remain sharper for 3 times longer than the Nicho ever could. I would need to spend 3 hours min sharpening it, just to keep up! Simple maths- the hard point has saved me $135 in productive time in the shop or out on site; which buys a lot of metal! At that rate I can afford to buy 2 Jap silkys, 2 Bahco 14 points and 2 Bahco 7 points and still have change in my pocket! It also means I can afford to have 2 spares! In truth I have several. I use one for general work and keep the spare for delicate cuts as needed or in case I bust one (particularly on site). When the 1st one wears out, I start using the old spare and buy a new spare for those delicate cuts again- and so the cycle goes- The Japanese have developed pull saws to an art form and the steel to match. My closest friend is one of the best, old school, cabinet makers I know. He and I both agree, our sharpening skills, can not match the sharpness or the fineness of their saws! They are unsurpassed for precise hand cutting and a joy to use. We both gave up on sharpening saws over 15 yrs ago; about the time hard points became so cheap. Why? They cut so straight, so fast, so cleanly, for so long and for so little money! It takes a long while to get that good at sharpening saws with files- even diamond files! It just isn’t worth maintaining the classic old saws unless you have a lot of free time or want that added satisfaction of knowing you created that fine piece of wood work with a saw you sharpened yourself BUT REMEMBER! It’s a labour of love that comes at a SIGNIFICANT HIDDEN COST!! Don’t get me wrong, my mate and I have a combined collection of over 50 beautiful examples of the saw maker’s art- from 8 inch, 26 point British Tyzaks to 4 foot cross cut Distons and we love them all!!! We have sharpened all of them at least once so we do use one or two occasionally but 98% of the time, we will both reach for the hardpoint or Jap puller. If you accidentally tread on one and bend it- no big loss and easily replaced! When they finally lose that razor sharp edge, they still make great nock about pruning/camping saws or yes, cut em up into scrapers! If they made chisels or plane blades that compared to hard points I’d swap in a heartbeat, but hey! I love using chisels I’ve sharpened and could shave with! It really is hard to beat a hard point though- Near enough is never good enough! Do it once. Do it right and only then can you be proud of what you do! Get the point? H