Since so many people seem to have misunderstood I’ll try to help. Steliyan is referring to the fact that when rubber is put under load will initially resist more and then relax. This is why the input drops from 70% to 60% without his foot moving or the force he’s putting in changing. He isn’t referring to elastomer blow out or age related rubber degradation. It’s a fundamental flaw in the decision of sim pedal manufacturers to place elastomers between the input force and the loadcell censor. The issue can only be corrected by using metal instead of rubber as this is the only way to avoid the inherent molecular problem.

@chepilevski

9 ай бұрын

Thanks buddy 🍻

@alecmillea4539

9 ай бұрын

@@chepilevski no worries my friend! I thought your explanation was fantastic, don’t know why some people didn’t get it but sometimes hearing it slightly differently helps people understand!

@chepilevski

9 ай бұрын

It is normal thing 🤛 Thanks again bro 🍻

@zazadj1

9 ай бұрын

Hi Steliyan at the end what do you use on the p1000 angle sensor or load cell, the problem of relaxation did you solve with the hydraulic piston? Thank you always for these technical lessons

@alecmillea4539

9 ай бұрын

@@zazadj1 He answered these questions in previous videos and comments so I’ll take the liberty of transmitting the information. He ended up using the Hall effect angle sensor because it prevented the elastomer relaxation issue. The same issue remains present with the hydraulic kit as it’s still compressing elastomers.

I am an engineer and I work with elastomers. I will try to break down the phenomenon being described a little more completely than I have seen so far, although there are already some good explanations. Elastomers are viscoelastic. This means that they can behave like a viscous material (like honey) such that when you apply a load to it it will continue to deform slowly after the initial deflection. When the load is removed the elastomer will elastically recover close to it's original position and for the most part be undamaged. There are two ways to measure viscoelasticity. The first is creep. You load the elastomer using a constant load (weights are good). The elastomer will have an immediate deflection, then over time it will deflect more or creep. You apply constant load and the deflection slowly increases. The second method is called stress relaxation. In this method the elastomer is deformed to a specified position and then held there. The load in the elastomer is measured. Overtime the material relaxes and the load decreases. When talking about how this affects muscle memory it really is dependant on the type of muscle memory you have. If your muscle memory is positional, meaning you press the brake to a specific position and hold it there the elastomer will experience stress relaxation and the load on the load cell and the load on your foot will decrease after the initial brake application. If your muscle memory is load based, meaning you have a memory of how much force you need to press the pedal, then the elastomer will experience creep, where after the initial pedal press, the pedal will begin to deflect further during the braking zone. But the load on the load cell and on your foot have not changed.

@chepilevski

9 ай бұрын

That is great explanation from expert ! Thanks for the post buddy, it was really informative 🍻

@DutchBarbarianOfficial

8 ай бұрын

This is the correct answer. I'd like to add to this that there are rubbers and there are rubbers. Most companies use the same standard off the shelf rubber compounds/inserts. There are also companies that do not igone the issue of creep and relaxation and actually developed their own mix of rubber compound to improve the characteristics of the rubber. In addition, muscle memory is almost always force and motion based, not necessarily position. Meaning you can automatically (without paying specific attention to it) do a certain motion with a certain force. This is not really the case for position, hence the incredible difference in performance when someone switches to a (actually) load/force based resistance in their pedals.

@benistingray6097

8 ай бұрын

This so much! Only people who use a certain pedal position as their reference will have problems with that because a good simracer will modulate their braking pressure after the initial brake anyway so you correct fot that elastic change in the rubber anyway.

@LymarkW

7 ай бұрын

I'm a noob and this is a lot to take in. I've been re-reading this for a couple of times now. Just wanted to make sure I understood this correctly. I play with a very stiff and short travel brake - load as my muscle memory. Am I correct to say that this phenomenon wouldn't affect me as much, if at all, since the deformation(creep) of the elastormer has nothing to do with how much pressure the loadcell is reading from the force that's being applied by my leg?

@jeremymercer5655

7 ай бұрын

@@LymarkW Correct, with a stiff brake pedal there wont be much initial deflection, and the creep will be smaller as well. The load at the load cell will always be proportional to the load at your foot and the viscoelasticity does not affect this. With load based muscle memory, the viscoelasticity will not affect your inputs. And with a very stiff pedal you are unlikely to notice your brake pedal deflecting more during the brake zone.

Materials engineer here. You're not an engineer, but you definitely understand the basic concepts and are able to explain them well :) Good content! PS. I'm using springs too ;)

@chepilevski

9 ай бұрын

Nice to read a comment from professional 🍻

@elmalloc

9 ай бұрын

as an engineer please contact sim pedal manufacturers and have them fix this issue!!

@zqzj

9 ай бұрын

​@@chepilevskiI'm not a materials engineer but I think I came as close as possible to mimicking hydraulic pedal feel with an elastomer spring configuration. I did a ton of research on materials and testing various setups like you did, and I came across a combination of components that gives the best pedal feel possible without going hydraulic. To start, I found everything I needed at McMaster-Carr, they sell an almost infinite amount of industrial supply components (only place I could find this stuff). I have a total of 4 springs of 3 different types. The first is a spring-tempered steel spring. This steel spring is preloaded to 50N and maxes out at 160N but can easily take a 1000N of force without deforming any further. Travel for the steel spring is 7 millimeters after being preloaded. The rest of the springs are what's called High-Load Fastener-Mount Compression Springs, and these give more of a hydraulic feel than any elastomer or spring I tested. I used two 9732K11 springs and a single 9677K3 spring. I also included cut-to-fit acetal dry-running sleeve bearings to eliminate shaft friction under load. My loadcell has never performed better.

@zqzj

9 ай бұрын

@hansjmo I'm curious as to what spring configuration you're using?

@hansjmo

9 ай бұрын

@zqzj your taken this further than me, im using simagic p2000 haudraulic pedals with two stage springs, but im currently building some pedals i can reverse mount. I got my hands on a variable haudraulic damper, and im thinking of running a two stage spring setup with some elastomere rings inside the soft spring. Im learning cnc in a makerspace in oslo and will cut 5mm carbon plates (inspired by hausenkveld). I hope it feels good and that i can tune them properly 😀

Good video! From a technical perspective you’re absolutely right and this is one of the reasons I generally opt for a spring and stiff elastomer combination on most pedals. The spring brings me to my threshold point and the elastomer provides the necessary feel to modulate around it. One point to consider though, how often are you actually trying to hold the brake at a fixed position? My personal take on this is that as long as the response is consistent, you will establish appropriate trail braking muscle memory that accounts for this relaxation, just as a real life racing driver will account for g-force, brake fade, ballooning brake lines, pad wear, etc. Of course it could then be argued that in a sim we don’t have the seat of the pants feel to assist us, but again we are talking about a consistent relaxation of the elastomer here, not something that is changing throughout the course of a race. I can say from my personal experience using a huge variety of different types of pedals, I’m no faster on pedals that use springs (VRS for example) or even pedals that use a totally different design like the SC Active Pedals. As long as I have a consistent and clearly defined threshold point that I can hit consistently and modulate around, I’m fine. One very interesting design I tested was the Sim Coaches pedals a few years ago. They used concave metal washers that acted like a spring when pushed together which gave a very consistent feel and a huge range of adjustability.

@chepilevski

9 ай бұрын

Hey Will, do you mean sim coaches used Belleville Washers for elasticity of the pedal ? If yes, i didn’t know someone did that already as that’s sounds like really cool idea someone pointed before and was looking to see how that can perform and what choices of compression they have 😮

@boostedmedia

9 ай бұрын

@@chepilevskiyes that’s what they’re called. They included a selection of different thicknesses so you could basically dial in whatever combination you wanted. Unfortunately we had some major issues with the pedals in other areas and ended up sending them back, so I can’t comment on how the washers lasted, but have a look at my review video on them to see how they used the washers.

@chepilevski

9 ай бұрын

@@boostedmedia that really interesting man. Is unfortunate there was an issue with those and you couldn’t test them further! I will check out how they did that as it seems to be very interesting concept!

Great video and thank you for breaking that down. It makes sense that over time, with heat, etc. the rubber will begin to break down and not have the same resistance. I’ve experienced this myself with my DIY mods. Working with springs alone does seem to be the best way as they are designed to have that constant movement with minimal degradation if you will. Another like from me for sure. Thank you again!

@chepilevski

9 ай бұрын

Yeah man , in some elastomers is huge problem 🙈 I found springs to be way more precise in the initial push keeping there load and speaking just 1-2% which doesn’t make difference

@TheKornfeld

8 ай бұрын

Just to clarify: what you describe is part of the problem, but it does not need to involve the rubber breaking down in any way. It is an inherent problem to the rubber itself. At 3:00, he introduces a paper that opens with "three distinct categories (of problems when using elastomers)." He goes on to focus on the third of those three problems, which is that when you press on the rubber elastomers, they don't respond exactly to your inputs. You press on them, and they transmit that force, but then they relax even when you continue pressing on them with the same force, and even when the rubber elastomer is new and in good condition. That is discussed at 3:34. It's a problem with new elastomers that are in good shape, not just old and worn out ones. It's a problem with the elastomers themselves.

@chepilevski

8 ай бұрын

@@TheKornfeld thx for the help buddy 🤛

This phenomenon has been well documented in sim pedals for years. In terms of actual difference when racing im sceptical since its rare that you ever hold a constant pressure for very long at all.

@chepilevski

9 ай бұрын

That is correct , not all corners need constant pressure for more then 2 seconds indeed!

Very interesting & thought provoking video, RBM. I've always (personally) wondered if there is another side to this - which is driving "by habit". To explain, I used to get together with my brother to race once a month at our homes, selecting a new car & track, and Hotlap it till the fastest time won at the end of the day. But one thing that hit me hard, was that if it was a track I already knew. I noticed that I especially braked always at the same place, and say ALWAYS changed down the gears once or twice automatically which might have slowed me down too much, but did it just out of sheer habit. It was only when it was my turn to watch my brother, that I was able to see if he was able to take corner ABC for example without lifting off / where I would brake at a certain point JUST OUT OF HABIT or MUSCLE MEMORY??? So it became a ritual where I watched him, and at times, he watched where I was faster (using my slow in, fast out technique) that we BOTH became faster, when we threw out our own ways of driving any track due to sheer habit. So I've always wondered if that is a (kind of?) muscle memory also??? I hope that made sense to you RBM, as I tend to waffle on a bit too much, hahaha.

@chepilevski

9 ай бұрын

That is also big thing man! With the years I realize when I start practicing a track for a week or two , I just couldn’t improve at some point and when I come back months later I’m faster ! That exactly what muscle memory and bad habits do to our performance and we start doing the same thing over and over again expecting different results 🙈 When we come back later and those habits are not polished we can actually try something new which can help or of course make things wrong! There is lots of sense in your story up there 🤛

Great content as allways, any tips to be faster is very much appreciated .

Thanks ! That explains in great details the point we discussed few weeks ago ! Coïncidence ?... Today, 5 years after buying it, I remembered that my T3PA Pro was provided with an optional accessory : a bracket with a choice of a spring or rubber that fits under the brake pedal ! I just chose the rubber since the spring doesn't feel very stiff between simple fingers. Now, I need to build that famous muscle memory ! Until I eventually spend money on a Simagic P2000 or P1000, a Sim-Lab XP1, or another brand ...

I noticed this deficiency with the load cell after coming from a cheap set of Logitech pedals way back. I think those used POT's but I noticed the braking points were more stable with less variance as I held the pedal in a constant state of pressure/travel. With that being said I was more accurate with my braking once I switched to load cell because of the feel but I never forgot this fact through my sim racing years. Recently I have applied an inverse exponential curve to my braking on my sprint pedals and it feels much nicer than the linear behavior that is stock in the software. I think is due to the high end of the curve being slightly saturated that doesn't allow for as much change during the final compression stages at 80% brake. After watching your video this makes sense because as we compress the elastomers they exhibit a non linear behavior at the extremes. With my curve the mechnical properties of the eslastomers are filtered at the extreme compression ranges. Could you do a video on this topic and potentially test? I think that you will find this will be a better way to solve the problem beyond changing the elastomers for springs. Let me know what you think. I am an electrical engineer and not mechanical but after reading the documentation in your video description it makes sense to me.

@chepilevski

9 ай бұрын

Wow, that is such a logical explanation of why they start working so much on those curves in the software and makes so much sense! That is definitely something I completely missed and must test ! It makes so much sense 🤛 thx buddy

@gregglasscock7470

9 ай бұрын

@@chepilevski No problem man thanks for making the video. I would also like to add that saturating at the high ends has the negative effect of less linear control but the way I see it I never modulate at the high ends anyway. I am simply off and on that limit. The portions for trailing and medium braking retain that linear behavior however so it works out great.

@chepilevski

9 ай бұрын

@@gregglasscock7470 that’s exactly the case man, we usually hit the brake hard quickly at the beginning and keep it there as long as we go straight and there is no any modulation of the pressure and then we drop down like from 80-90 percent down to 30-20 very quickly and modulating that turn in releasing even further! I haven’t tested that yet but those curves makes so much sense and can be tested easily! I’m so excited about that suggestion as it can be the best and easiest solution for most of the people out there 💪

@stubbsyyy

9 ай бұрын

Hi Greg, as sprint owner too I am really interested in the curve you are using. What are percentages? Cheers, Chris

@gregglasscock7470

9 ай бұрын

@@stubbsyyy I think it is called S+1 or something like that. It's right under the default curve. I slightly edit the saturated top end to my liking. I think it will be up to the elastomers that you use.

I've modded my Ultimate-brake with a quite beefy pressure spring about two years ago and tried elastomers in between, but kept the spring-mod, which works great for my brake-pressure (50-60 kg). Now it's one elastomer and two springs including the default small one and I've added a bump-stop inside. I've also tried to replace the elastomer with a plastic one, but the elastomer adds a little more brake-feel to it and the Heusinkveld's are much better than the average ones. Elastomers are widely used for brake-pedals because they feel more like a hydraulic brake compare to a spring in the first place while being cheaper and less prone to leak than hydraulic brakes.

@chepilevski

9 ай бұрын

Great to hear you found mod for your ultimates buddy 😃

@piereligiodisante

5 ай бұрын

Same setup I have on SimJack pros. I've kept one elastomer (the short one, like 3cm), and two springs of different rate. Full spring wasn't progressive enough for me. I like the setup a lot now. Maybe it could be even better replacing that elastomer with a better one, but I don't want to increase its rate so I don't know

@diysimguy

3 ай бұрын

I did the same mod, what a differnece!! I used red long die spring and one of the smaller had Ultimate plus elastomers.

good break down and i hope the companies are watching this. ive noticed with my CSv3 every 6 months im adjust the pedal tensioner to make it stiffer and this is with the brake kit.

Hey buddy, it's been a while 😀 This is a very interesting subject, thanks for the information. I use Fanatec V3 pedals with the elastomer and damper kit upgrade on my brake pedal so I might not be able to replace the elastomers with springs due to their size and location. But this makes so much sense as I usually have to make slight adjustments to the brake pedal every couple of months or so to add some more pre-load to the elastomer. Now thinking about it, I guess that having the elastomers so snuggly fit inside the metal tube may prevent it from expanding past a certain amount. 🤔

@MntRprznt

8 ай бұрын

I just ordered myself a set from china. You need 12 mm wide and 55mm long in total [so combination of 25 and 30, or any other totalling 55 will be fine]. Theres different compression values in kg, so maybe mix some up to see whats good for you or to create progression.

Really nice video. I have made the same observation on my dutch pedal set. A solution to the non-linearity (between pedal travel and pedal force) with springs is the one used in the VRS pedals, with a rotating cam construction. I tried those pedals 4 years ago on the sim racing expo and they were my highlight of the show, they felt incredibly precise. There is one other aspect to consider though, and maybe you can dig into that a little: How do the hydraulic systems in real race cars behave? From my memory, these brake pedals get stiffer the faster you move the pedal (has to do with the hydraulic liquid moving through holes separating two chambers). This damping effect can obviously be felt and the elastomer brakes on sim racing pedals may be immitating this effect quite well, much better than any linear spring ever could. Therefore my question: Isn't this behavior of the elastomers very comparable to the behavior of hydraulic systems in real life race cars, and aren't we thus facing a choice between realism and maximum precision / performance? And: Is the VRS design with a spring, rotating cam, and additional adjustable hydraulic dampers potentially the perfect construction, aside from active pedals? 🙂

I'm not a material engineer but I did work with elastomer for aeronautics as a quality and lab testing manager. I'm surprised no one have talked of the issue you see with the compound. 1-There is a mix of different material to make a compound, it depends heavily of what your are trying to achieve 2-You need to bake the elastomer after molding it. This will help release gases, and also aging the elastomer faster so it will be more stable during it span life. The oven curves are very precise depending of the compound. These curves have steps with duration and slope to reach T°. All of this help your compound to have a very repeatable behavior (what I was checking with the lab tests). Hope this will helps the debate. 😅

This sounds very curious. Will have to take a look i'm on heusinkveld sprints but always had trouble holding that peak pressure

@chepilevski

8 ай бұрын

I would love to know how it goes with your set and if you find solution to it buddy! There are many on this set who are looking for to solve it !

To be honest I never thought about this but now as you mention it, it's logical and fitting with my physical understanding about rubber. I think this is a very important poit, when it comes to optimum braking feeling. Thank you very much Stelian to talk about this problem of elastomer behavior. Sorry for my bad English🙈😅

I had to watch this twice as I kept getting distracted by the simulation graphics and the rig setup - incredible. Great information!

One thing that I have always wondered, is how people swear that hydraulic brake pedals are much better than regular load cell brakes. As I see it, the hydraulic brakes still compresses rubber, just like load cell brakes. You just move the rubber away from the pedal, but the feel/effect should remain the same. The argument I hear people say about hydraulics, is that a real car has hydraulic in the brake system and therefore it is better/more realistic. Well, the hydraulic on a car, and on the sim brake pedal, does not compress. The compressing feeling you get in a real car is 90% vacuum brake booster and 10% pads to disc travel and maybe a very small compression here as well. IMO if anyone wants to simulate a proper brake feeling, air/vacuum system is needed or an active pedal.

Thanks mate for your time making this informative video👍

@chepilevski

9 ай бұрын

Much love brother 🤛🍻

Manufacturers are going to need to implement a software & hardware solution for this. In simple terms, monitor pedal movement with a sensor and maintain input level via software if pedal hasn't moved. Ive noticed this issue too but thought it was just me and my inconsitent foot! Thanks for making a video on it.

@chepilevski

9 ай бұрын

That will be great if they do indeed buddy!

biggest point most ppl dont understand muscle memory is automated movement and not pressure . i always configure my brake so that i´m at about 80% with only spring compression and the last few % goes into the elastomeres . but thats not muscle memory anymore thats only for more realistic feeling

@chepilevski

9 ай бұрын

Yes man,many think exactly that🙈 When people type for example on there phone explaining how angle sensor doesn’t work and must be pressure sensor, they don’t even realize while typing that there fingers reach every letter without even looking ware is positioned on the keyboard from that automated movement they have created typing massages for years ! They are reaching every symbol trough that muscle memory not trough pressure! Automated movements are just controlled from different part of the brain which is an awesome feature we have to be able to do many things at one’s without consciously trying!

I always wondered why that always happened to me when I felt like I was holding it at the same position and pressure. Thanks so much for the fantastic scientific explanation! You did a great job of explaining it! I’m searching for springs to replace my elastomers already lol!

@chepilevski

9 ай бұрын

For long time I was thinking my muscle can’t hold but wen I test those bad elastomers year ago which ware drooling like more the 25% and sometimes from nowhere I was missing corners from my normal braking point bay large distance I realized is not me ! Wen I talk with people about this everyone is think the same way and blaming there feet but is not🙈 Now having both sensors on the same pedal I can clearly see what is happening and was the final prove I needed! We where checking different guys telemetry mostly with HE Sprint pedals and we can clearly see that droop of the braking curve instantly after initial braking ! It depends from elastomer to elastomer but as much more we deform them in initial push that much more they relax later

@alecmillea4539

9 ай бұрын

Crazy that the drop off can be as much as 25% with some elastomers! It makes sense that the effect is magnified the more compression the material experiences. I can’t believe it’s not been noticed talked about and accounted for before now!!!

hope your doing well and awesome video as always deff ordering a few elastomers and springs 2 keep for spares

@chepilevski

9 ай бұрын

All great here buddy😃 Hope you are doing well too and have a great week 🤛

If you're refering to P1000 elastomer issue, it's not because of elastomer. The loadcell ballhead is too close to the black metal cover which collide with the loadcell under pressure. If you remove the cover elastomer works like a spring. No drifting at all.

@chepilevski

17 күн бұрын

Thanks for that info buddy 😮 I will definitely give it a go 🤛

This is so true, im really looking forward to buy the P1000 since you made the review, they would be my first hydraulic pedals. Great video as always!!

@chepilevski

9 ай бұрын

I love those pedals man , definitely the pedals of the year 💪

Thank you very much! I thought it was my own strength failing, being tired after initial brake pressure, and that I need to "focus" more in order to brake better. Now I could switch to the position sensor for the first 80% and I would not feel bad about it.

@chepilevski

9 ай бұрын

I’ve discussed this with many people over the last months and every one who have noticed this phenomenon was thinking , his muscles couldn’t keep up at that constant pressure! Some start trying to compensate with adding more pressure after the initial input to compensate but then we saw on the brakes telemetry the input goes all over the place 🙈

Very cool. Thanks for making this clear and sharing! I was not aware of this - I have not gotten into expensive pedals yet, but now I have a better understanding for the future

Cracking video mate, I thought I was the only one scrathing their head over the way elastomers behaved under contant compression. When I built my DIY pedals I ended up mixing springs and elastomers to get the best of both worlds, preload spring at the top, elastomers in the middle and a softer spring at the bottom, you get a nice progressive repsonse from the brakes but the two spings seem to help compensate for the spiking you get during and holding the brake.

@chepilevski

9 ай бұрын

Yeh man 🙈 it took me long time to fully understand what is going on with all those pedals I’ve tested

@theoldgitwatgames4640

9 ай бұрын

@@chepilevski Yeah, I went through everything from grounding the pedals to adding ferrite cable shields, did nothing brake jumped all over the place in DIview. Added springs and that stopped. It's good to hear manufacturers are thinking about it too.

@alecont6488

9 ай бұрын

@@theoldgitwatgames4640 Hello my friend, is it possible that you can share an image and possible technical data of your combination ?? Currently I also have DIY pedals, I am satisfied with it but I still feel that the brake is not at the exact point.

@theoldgitwatgames4640

9 ай бұрын

I used a mix of 30mm compression springs and I think a 90 shore elastomer cut into 3 sections with washers in between. The springs were a mixed batch from I think 60nm to 100nm compression, and just tested until they felt how I wanted them to feel. Like a lot of things sim related the feel is subjective and needs a lot of fiddling and testing to get right. Hope that helps?

@chepilevski

9 ай бұрын

@@theoldgitwatgames4640 thx buddy 🤛

This is such an awesome video. I would recommend that after watching the whole video, everyone jump to 10:23 and watch at 0.25x speed up through about 10:34. It's a clear visualization of the problem shown. The pedal goes to the same spot, and the force from the foot is held constant; but the output is not constant. And it is **not** because the elastomer is worn out. It's an inherent problem with the material of the elastomer itself.

Your videos are the best

Finally someone raised this issue. And I actually did just that, I got Simforge mk1 pedals, which are amazing for the price, and asked for a better set of springs and elastomers - and the manufacturer listened!

@chepilevski

9 ай бұрын

I love when manufacturers listen the community 💪

I 100% agree with you on the rubber performance. I created the perfect setup on rubbers, but noticed a tinny gap down/dead zone after 150 laps around the Nurburgring. Can't wait to throw my hardest spring on the bottom of the healthy rubbers with some fat ass spacers in between. That combo always worked for me, but we like to experiment and change, even when we know it's a temporary thing and that's what makes sim racing one of the most uplifting experiences on earth

@chepilevski

9 ай бұрын

That last sentence bro 💪💪💪😃🍻

I never thought of that. Hmmm... NGASA won't have a fix for that. So it's going to an adventure to find the right spring, length, hardness of the spring and big/small enough to fit in the sensor housing. Thank you for the new project. Excellent video as always.

I always preferred mixing elastomers with spring.... now I understand why. But then you try the simucube pedal, you adjust the muscular hard point to match around 80%... and boum everything become easy, consistent and brings so much confidence.

@chepilevski

9 ай бұрын

Those are next level man 💪

Pedal manufacturers insert these rubbers to appease drivers to match their sim pedals to the car they drive in real life. In go-karts and F1 cars, there is only the slight flex of the pedal itself, so the pedal travel is only millimeters. It's more like trying to push a brick. I have a Ricmotech load cell conversion for my old Logitech G29 brake pedal, which has zero rubbers. It feels just like the brake pedal in a go-kart, so muscle memory is a lot easier, as it is just pressure applied, with hardly any actual brake travel. I wouldn't swap my pedals for anything else on the market, until someone makes pedals without these artificial brake travel rubbers. A lot of sim racers would benefit from a try-out in a real race car... they would be shocked how hard the brake pedal feels.

I work at a spring manufacturer and test springs every day. Unless you take them to solid height ("set" them) they will always return the same force at a given length. I've always wondered why so many pedals utilize elastomers instead of a spring spec'd out for the correct rates. I guess cost is a concern, but honestly, when you are talking about the steep costs of some pedal sets I think elastomers are just a strange decision in perceived top shelf gear.

@LymarkW

9 ай бұрын

I've zero clue on how all these work, but say If I were to look for high-quality springs, are there any well-known brands or maybe certain criteria that I should keep an eye on? Thanks!

@chepilevski

9 ай бұрын

That’s is something which drives me crazy! All pedals are so expensive and if the cost is bit bigger it must not be so impactful for the end cost of those expensive pedals!

@chepilevski

9 ай бұрын

That’s great question buddy

@racekraft

8 ай бұрын

I think they use elastomers because it feels more realistic. The resistance of a IRL hydraulic brake pedal is not linear, unlike a spring. I've tried spring pedals and it feels totally weird - it's like my foot sinks to the bottom.

Sound like all this time we have been trail braking without realising😂

@chepilevski

9 ай бұрын

Exactly 🤣🤣🤣

I have been talking about this since I changed from elastomers to spring pedals on my live streams. Nice explanation here, kudos meng🤘

@chepilevski

8 ай бұрын

Awesome bro 💪😃

Using hall sensor pedals as my first set. After seeing this and being told to go to load cells as an upgrade I am more than happy to stick with my current hall sensor pedals. Muscle memory wins in both cases. Great video and thanks for sharing.

This property of elastomers (hysteresis) is an essential ingredient and the reason why tyres generate grip. The delay in the return of the rubber to its original state due to a damping coefficient in the material. Optimal temperature window yields the most favourable damping coefficient of the elastomer and thus peak grip.

The main issue I have with pretty much every loadcell pedal set with rubbers (brake pedals mostly) is that if you want more force (applying more force to the pedal), this almost always comes at the cost of less pedal travel. I personally like a long pedal travel but with a decent amount of force with that and the Simucube Active pedal allows me to achieve this. I don't think I can go back to a traditional rubber brake pedal ever again.

@robertschneider8808

8 ай бұрын

Simtrecs seem like they can do that due to their Signal amplifying knob on the Brake pedal. At least as I understood it. you can Set up the Pedal with long trevel but tune the signal amplifying so that it's still hard to press.

Super cool! I really needed you to keep this a secret since your last video; now any competitive advantage I might go after is gone! lol. But in seriousness, have you stuck with the load cell after getting the hydraulic kit or are you using the angle sensor on your P1000's? The difference between the load cell and the Hall sensor response can probably be matched by adjusting the brake curve on one of them too, right (in case the load cell's response is preferrable)? Thanks again. Always a pleasure to watch these videos.

@chepilevski

9 ай бұрын

I found the way to feet the springs from the Cube Controls pedals inside the hydraulic system and honestly doesn’t feel much different then the elastomers ! I haven’t yet decided meager I prefer as the linear from the hall sensor is not bad but as you’ve said, curves can make them work equally! Must test that as well! Thx for the suggestion bro 🍻

Great explanation.

I use a TLCM, I used the softest springs so that it just goes back to the zero pedal stroke, and washers so that it has direct pressure on the load cell once you hit the preferred stroke in relation to the throttle. This is a very consistent fix. I then tweak the gamma and and the stroke percentage to make the brake feel softer or harder.

In a nutshell: it is not about having a load cell as much as progressive resistance, however it may be provided, repeatability in the way it is measured, and stability in the reading. Elastomers and hal effect sensor could do as good of a job as springs and load cell, or pneumatic and pressure reading... But elastomers and load cells seem to be a bad combination.

Subbed, I love gaining new technical insights about my hobby, and this was presented very well! It's hard to argue with those load cell readouts. I guess I'll hold off on my load cell mod until I have metal springs.

@chepilevski

8 ай бұрын

Sounds like a plan 🍻

@excrubulent

8 ай бұрын

@@chepilevski Apparently yt is removing my comments and threatening my channel over spam so I WON'T mention where I'm getting them from, but I'm getting multiple die springs to see which ones work. If I can I'll find out what their rates are and report back.

Awesome video. Agree 100% I hate rubber elastomers wish I could find some springs for mine.

i replaced the rubber with hardest spring and two springs are working so much better! thanks buddy! 🎉

@chepilevski

5 ай бұрын

Awesome to hear that mate 💪

You might not have an engineering qualification, but are most definitely an engineer! Nice video.

@chepilevski

9 ай бұрын

Thx for the compliment buddy 🍻

Man. I have an SRP Pedals. They use a completely different pneumatic system and it feels amazing. My driving went to the next level with those pedals. I’ve been trying to create a video for them but I have a very busy life. I was hoping someone like yourself can review their pedals but unfortunately the company is too small to provide review samples to reviewers. Dan Suzuki made a great video about them

@chepilevski

9 ай бұрын

I believe you bro 🤛 I would love to test those !

Everything I see this rig I'm amazed. You done such a good job

@chepilevski

9 ай бұрын

Thanks for the kind words buddy 🍻

Bought tlcm's while ago. I hated felling of bottoming springs even with both reds you can easily press the brake pedal to the end and feel sudden stop. My experiments with rubber elastomers got me the right feeling, of course the travel of the pedal has shortened but it felt just like real brake, press it hard and you don't feel sudden end of travel but it is almost imposiible to push more. I immediately noticed that input values dropped after moment when pedal is pressed but i thought it is because my lack of training. After this video i'm giving springs a second chance.

@Turbonuotti

8 ай бұрын

Yeah i am willing to sacrifice the real life brake feeling if metal springs give me better control over the brake force, i'll definetely try this today when i get home

@suley1990

8 ай бұрын

@@Turbonuotti 3 days since springs are back. Bit of getting used to but (hate to say it) overall better brake control especially in long braking zones. Feeling is not as terrible as i expected.

I noticed my trail braking wasn't as strong in the later parts of 45 minute races and my lap times were dropping off, I had the load cell too strong at 65kg on the sprint pedals ... I feel like I physically fatigue as an endurance race goes on so iv lowered the pressure to 45kg and steepened the angle of my pedals which has helped keep the pressure on the brake for endurance racing when I'm getting fatigued and iv found in the later stages of the race im getting the car to turn in as sharp as the start.. thanks for making this content to help us think about how to become faster drivers. My situation was slightly different than what you explained in the video but your video made me think about my braking 👍

@chepilevski

9 ай бұрын

Yeh man , I had exactly that same problem with all pedals before thinking hard pedal is good thing! Sometimes I was getting fatigue even before start the race and couldn’t reach my threshold after 1-2 hours on the track ! I was very afraid of that panic brake trough high adrenaline but then I found using hard pedal mixed with army feet was shaking like crazy in the first two laps ! I also f….d my knee with those stupid hard pedal settings! Now I use only soft settings with medium travel and try to calm down my adrenaline spikes in the beginning of the race with some breathing techniques! So happy I did all those changes!

This is why I love the asetek forte pedals, it uses an elastomer, but the only contact to the load cell is a spring, so it’s lovely and stable

Fanatec V3s elastomers sit in a metal tube housing stopping them from bulging. That should help negate this effect. I'd imagine if someone started offering metal housings for their pedal's elastomers this effect could be largely reduced. As for it helping people become faster, I'm not convinced. Most people already have their pedal's characteristics baked into their subconscious and are compensating for this effect. But, then again, sim racers are like hypochondriacs. Instead of their bodies it's their rigs that they believe there's always something about it that needs to be cured to make them faster. Just remember, there's always some kid on a G29 in a lawn chair in front of a TV hanging above a fireplace running faster laps than you.

@chepilevski

9 ай бұрын

You are totally right and probably for some people will not make any difference but still, it is good to be at least aware what’s going on and if there is a chance, to have full control on there own and not the hardware doing the job 🍻

@MntRprznt

8 ай бұрын

Nah, dont think youre right buddy, mostly because theres two sizes of elastomers for V3's - the 12mm and 13mm wide - you cant tell me the 12mm wont expand more than the 13mm in the 13mm chamber [i think the chamber is actually bit wider]. Also, there are different hardnesses, they will also act different, even the 13mm one will react more the softer one you choose.

@jeffwills2869

8 ай бұрын

@@MntRprznt Yes, the 12mm will bulge more than the 13mm in relation to it's size, but neither can bulge beyond the confines of the tube.

@MntRprznt

8 ай бұрын

|Do me a favor then and go to your fanatec control panel on the pedals page, depress the pedal 100|%, release few % and hold the foot super still. Watch the value on the gauge. You'll see it dropping A LOT slowly. Thats why it doesnt matter if the elastomer is encased or not. It still slowly releases tension. @@jeffwills2869

I think the main issue with people thinking hall sensors are not as good as loadcells is all to do with the cheap pedals that used to use them. Those old pedals only measured distance but the pedals were always super light and not enough travel. Having a good set like the p1000i I have the hall sensor is perfect. As Stiliyan says the feel under foot is the same as when using a loadcell. So it was never about the hall sensor being bad its was about the feel but people believed the hype and everyone ran with it "loadcell is best" but it's not that cut and dry.

@chepilevski

9 ай бұрын

Very well explained man , absolutely correct statement 🤛

Great vid thx. Now I know why my G27 pedals are wonkey during those hard sessions!

Springs are definitely the way to goi got mine in the post today. I so glad u done this video I’ve ordered some stiffer springs the ones I got are just a bit to soft. Again that was a great call from u mate ty. 😉

Awesome video man! Hope we can get more manufacturer's doing the right thing and over the next couple years switching over to springs :D

Agree. I had to use HE software which I was against to adjust my consistency. I changed from 2nd to the hardest to the softest which was better but still not giving me the results. It was me using software to make the experience more consistent. I would love to try the angle sensor of the Simagic P1000.

I think the problem won't be so bad, if the pedal manufacturers, added a tiny bass shaker with their pedals that vibrate at high frequency so you can feel the input and release. Another way is, adding auditory queues from squeeky brake pads and tire chirps via software.

@chepilevski

9 ай бұрын

They shakers are must for sure

Switched over to 40x14mm springs. Green was my preference. Tan was the heaviest. Huge difference in the 50% and below feedback compared to elastomers. This is affecting the trail braking feeling.

I've always been worried about this with elastomers, but since they're so commonly used and no one talked about it, I figured I was overthinking things and that it wasn't making a meaningful difference... it's interesting to find out my gut feeling was right all along. I am using a spring-based load cell set though, so I have not experienced braking with elastomers.

Perhaps if more people would have listened in school it wouldn't need further explanation, so here is my 2p worth. Rubber deforms when compressed. Over time that deformation changes. The rubber becomes harder or softer depending on the compound thereby reducing the consistency of the feel and the behaviour of the brake pedal which absolutely will reduce your brake performance. The simplest solution is to invest in some metal springs, about £5 per spring off ebay. This will increase the predictability of the braking experience and enable more of the muscle memory to be consistent over time. Oh, and one final thing. The 'Race Beyond Matter' explanation is spot on and they have a new subscriber.

@chepilevski

9 ай бұрын

Good one Martin and thx for the support buddy 🍻

Timely video, I was really excited to get pedals where I could mix and match to get the pedal to feel how I wanted. No matter how many elastomers I tried, it always didn't feel right to me as I could feel them resist then relax, which felt horrible to me. I didn't want to sim a car with balloons for brake lines or zero movement with rock hard elastomers, so ended up using a range of springs. Thought I was crazy not liking elastomers.

Aha, but what if, you already new this phenomenon or mechanical deficiency existed, you can use it to your advantage, as in automatic trail braking. I use Simforge pedals and oh yeah, you could see it happening on their calibration software! I recently purchased and received, their new Elastomer & Spring upgrade, which lesson the effect using the over sized (larger diameter) elastomers, in place of the standard size. Now I'v a more positive brake feel. I do like what the P1000 has with both, position & elastomers working together, but won't move to those, until the software is 100% sorted, across the board. As always great content!

Theory tested and confirmed on Fanatec CSL elite V2 pedals. With stock elastomers (blue preload spring, 65/75/85 elastomer stack) force drops from ~80% to ~70% over a couple sec. Using a 25mm diameter 35mm long blue die spring to replace the two softer elastomers, leaving the original preload spring/elastomer and one hard 85 shore elastomer, now input only drops by 1-2%. It’s a little too much travel for my liking so I’ll be messing around with different springs to get the feel I want but the theory is there. Way less force drop than before but still a tiny bit due to still using some elastomers in the stack. I’ll keep updating with what combination I end up being happy with.

@chepilevski

9 ай бұрын

1-2% is actually great result man 😃

@alecmillea4539

9 ай бұрын

@@chepilevski Man honestly I’m so glad you’ve brought this to the attention of the community! It’s actually a huge difference in consistency that can not be over stated. I can brake later into corners now because I’m actually staying at full braking pressure throughout the whole braking zone! It’s crazy it’s gone unnoticed for so long! We all were blaming ourselves!

So Thrustmaster choose to go with springs in T-LCM was not cost saving, or design flaw. Interesting. Good that this video came out, just at the time when I want to buy set of elastomers for my pedals;)

@chepilevski

9 ай бұрын

It is a headache 🙈

Very good video as always. Have you tested the Cube Controls pedals with the cups from the performance kit? Do the cups eliminate the problem or reduce it or is there no difference to not using cups? Thanks in advance.

@chepilevski

8 ай бұрын

Yes buddy, I used 1 blue spring and the yellow elastomer with the hard cup and have very stable load cell under pressure!

I have a set of Fanatec CSL-ELITE V1 LC pedals. In stead of getting a new set of pedals, I am going to get a cheap drill press and some wood dowels. I'm going to replace the elastomer stack with the dowels and go with a 100% stiff brake pedal. For these pedals, the stiffer, the better. I tried them without the elastomers behind them, and they have better performance with no travel and dampening from the elastomers.

We saw in the video that you are using 2 different Springs for the brake with the Simagic P1000. What kind of springs are they and where can we buy them? Awesome video! Cheers!

@chepilevski

9 ай бұрын

Hey buddy, I used at the end the two blue springs from the Cube Control SP1 pedal kit which fits inside the hydraulic container! Must check if we can find those somewhere else as that kit is bit expensive on the cube controls website

@amID0n

9 ай бұрын

Thanks!

Awesome videos! Thanks so much always for your great info. I have the Heusinkveld Ultimate+ pedals, but still find the brake pedal to have an “unnatural feel”. Which pedals do you recommend to get as of right now? (Around $1500 budget). The P1000’s? Thanks if you can respond

@chepilevski

9 ай бұрын

Hey buddy, thanks for the kind words and support 🍻 The budget you have is really big ! I can tell you why I choose to race with the P1000 as main pedals set ! For IRacing particularly, the haptic motors are my first reason as they completely change my driving/braking habits and I realize every car even in the same class activate ABS at different stage and also helps enormously in the trail brake process! In feeling the hydraulic system is sweet too but the feeling is not what I really care much but comfort operating each pedal and the inverted model really makes big difference for me as I’ve changed the way I push the pedals ! Now my heal has is down and support my movements which helps precision and there is zero fatigue after hours driving ! The haptic motors also are supported from SimHub last version with many effects which I haven’t tested yet but is cool to have that as well ! Those are the pedals many of my friends got after hearing my impressions and till now everyone who got them confirmed everything I felt which is very good sign and not just my personal observation! If you go that route I would love to hear your impressions and hopefully you will feel like us 🤛

@domenicofranco6246

9 ай бұрын

Have u thought about SRP pedals?

@Flyboy0985

9 ай бұрын

⁠@@chepilevskiAwesome! Thanks so much for your reply. Again, amazing channel and all the work you do👌🏼💯

@Flyboy0985

9 ай бұрын

@@domenicofranco6246 Thanks also for your reply. Definitely will take a look at those ones as well🤙🏼

very intersting ! I've got the p1000 set to angle to get the more stable feeling what would bring me the hydrolic kit based on elastomer too ?

@chepilevski

9 ай бұрын

The hydraulic kit comes with set of elastomers and aluminum spacers which minimize that problem by large amount ! I use 6 red rubber paces and 3 aluminum spacers which calmed down a lot the load cell sensor but I still prefer to use the angle sensor anyway 🤛

@JoFandango

9 ай бұрын

@@chepilevski why dont you get rid of those inperfect elastomers and use only aluminium spacers ? sorry for that bad joke... and thank you for your answer !

Do u ever heared about VRS DFP Pro pedals or Simgrade VX Pro? Both uses spring loaded brake pedal and feels amazing. When I switched from modded Clubsport v1 pedals to my DIY stuff, I tried to use springs because I seen problem u mentioned in my CSPv1s. Now I use 2x 30mm coil linear springs with ~40% compression. I tried to use 2 or 3 different springs but it I hated that braking in stages feel. I would like to have smooth progression but I don't think it's possible in HE like pedals without mechanics like u can find in VRS DFP pedals. I feel pretty confident with linear spring brake. It's hard enought to not press 100% in panic situation.

@chepilevski

9 ай бұрын

I believe VRS have made they choice as those guys there are Pros and they wanted to have precise inputs! I personally also don’t have problem with the linear feeling of spring compression 🤛

@FirssenSimracing

7 ай бұрын

@@chepilevski how about spring and elastomer mix? Can spring reduce elastomer relaxation or it doesn't matter? Have u seen Najam S120 pedals? They look sooo interesting (maybe except linear clutch).

Such a great video brother, i recognize the music obviously haha, i have a new sample pack coming soon but id love to send you a few previews for you to use before anyone else :)

@chepilevski

9 ай бұрын

Please do that 😃 Your music is more then the half of my videos man ! I’m getting inspired from it and start getting pictures before my eyes what and how I have to shoot and edit

@ImmersionaudioLTD

9 ай бұрын

@@chepilevski Hey brother, yeh man, works so well, i sent you a private message on instagram, as you know my music is all about what captures your mind my friendl :)

Good video and an interesting concept I hadn’t thought of before. Can anyone here recommend a good set of springs for the Fanatec CSL Elite V2 pedals?

Great video! Very good explained, too. Thx ❤

@chepilevski

9 ай бұрын

Thx buddy 🍻

Thanks for that technical insight. Super interesting topic, imo. 💪 question: how often do you clean your installed hardware, like pedals, wheel base or rig frame? Have a good day off, Chepi! 👋

@chepilevski

9 ай бұрын

Mostly every two weeks I use my compression for the dust buddy 🤛

@heelandtoeknee

9 ай бұрын

@@chepilevski yeah. My vacuum extension is called dust daddy! 😂 works well too. 👍

Hello buddy, I think you are totally right. I put your setup with the tree métal gold spacers and the 6 red elastomers. And at first i felt very inconfortable and thought it was too stiff, si I went to softer and run like that about a week. Then Yesterday go black on the full gold and red and its stiif ok, but i Can apply force and i realize that was so much better on low brakes. I mean with tiny pressure or trail braking, that is so responsive 😮 I was on point to sell them, but i am reconsidering my opinion, and man !!! That inverted setup is so much confortable ❤❤

@chepilevski

8 ай бұрын

I’m so glad to hear that man man ! For me ones I get used to those as they work completely differently when inverted, I never felt more comfortable in long stints drive ! Zero fatigue for hours 😃

Really interesting topic. Thx for sharing.

I frequently have to provide maintenance to my breaking pedal due to differences presented because of continuous usage of the elastomers, eventually if one uses the set of pedals for hundreds or thousands of hours you have to replace them elastomers.

Another reason why I chose the VRS pedals. No elastomers no problems.

@chepilevski

9 ай бұрын

That’s true and I think that’s the reason those guys made that choice! They are all pro drivers there

Hello man, i love your video but i want the video SETUP please, your setup is incredible and thanks you for your personality

@chepilevski

9 ай бұрын

I need some time bro 🙈 Big hug my friend 🤗🍻

@kayasou2539

9 ай бұрын

@@chepilevski yes, no problem, thanks you and good day bro

Great video. What are your thoughts on the Sim Magic P1000 pedals compared to the P2000 pedals. Is the price difference worth it

@Simlife101

9 ай бұрын

@frankvitucci6156 He's made a video about them in the last couple of videos just search his channel for p1000 full review then there's another video after about the hydraulic mod. I have the p2000 and the p1000 inverted with the hydraulic mod. For me the brake on the p2000 feels much better bit sadly for me my knees couldn't handle those pedals even on a weak setting as I needed inverted. The hydraulics on the p2000 has a 2 stage feel and u feel much better progression also i prefer the way springs feel over the rubbers/elastomers on the p1000i. The throttle on the p1000i is light but I love it and prefer it over the p2000. The clutch feels a lot better imo too my p2000 which I have right next to me on another rig so I can do one for tests and the p2000 is scratchy and a hard feel at the end of the travel which in my opinion is not natural but the p1000 is smooth and doesn't have that hard metal feel at the end. If I could get the feel of the brake on the p2000 on the p1000i or if the p2000s were inverted I'd go p2000 all day. The rumble motors I need more time with but I've heard their coming too the p2000s so... Watch RBM videos too get a good idea for your self. For me pain in my knees was ruining my hobby so I will take a slightly worse brake over comfort of the inverted p1000i and having the haptic motors from day one as the p2000 getting them is just what everyone is saying online so I don't take as 100%. Have any questions just ask 🙏

@frankvitucci6156

9 ай бұрын

@@Simlife101 Thank you, I noticed that after I posted the comment

@chepilevski

9 ай бұрын

I prefer the P1000 as they are better tough design and in inverted position and haptic motors they are the pedals of the year in my opinion!

Very good video and explanation 👍🏻 Thank you.

@chepilevski

9 ай бұрын

Thx buddy 🤛

Great Video as always mate , another topic , could you provide us your graphic settings for ACC it looks so much better , my settings are on epic (also Triple 1440p) but somehow it doesn't look good as your's, cheers 👍

@Simlife101

9 ай бұрын

@Bego666 he puts a lot of exposure on the game then counters it on the go pro. How you see it on your phone/monitor or TV with amazing pixel per inch isn't how it looks in real life I've had this conversation with Stiliyan He also messes with the image in post processing

@Bego666

9 ай бұрын

@@Simlife101 ohh ok well that makes sense , thanks for the answer mate 👍

I just saw that video and its really an answer to why my pedal input value was never steady, but mostly fluctuating with same pressure. Big thanks! For those of you saying you cant get springs for Fanatec V3's - I just ordered myself a set from china. You need 12 mm wide and 55mm long in total [so combination of 25 and 30, or any other totalling 55 will be fine]. Theres different compression values in kg, so maybe mix some up to see whats good for you or to create progression.

@chepilevski

8 ай бұрын

Hey buddy, we would love to hear from you when you replace those and share your experience!

@MntRprznt

8 ай бұрын

@@chepilevski Theyre coming, Ill drop you a message or a comment to let you know. I really appreciate your video on this subject, amazing insight. I saw those fluctuations myself, but just accepted it as normal. Never thought it can be solved with some experimentation.

@chepilevski

8 ай бұрын

@@MntRprznt we all thought the problem is in our inputs! I do this research for more then a year with many friends with all kind of different pedals checking telemetry and so on but was hard to do video before I have real prove and Simagic unintentionally proved that prove with putting the load cell and angle sensor in the same pedal! Now I can test exactly what’s going on with different elastomers and springs 😁

@MntRprznt

8 ай бұрын

I guess best would be a spring and a damper, but I wonder how mixing those springs of different stiffness would do - I ordered few 55 mm long spings of various kg values up to V3's lodcells max, but also mixes of shorter springs, to see if I can create some stable progression or better feel that way. Not too worried by progression though - this can be set in software if the spring will feel right. I envy your pedals - who wouldve ever thought that a hall sensor can make a comeback? xD @@chepilevski

@chepilevski

8 ай бұрын

@@MntRprznt I’m eager to see your impressions man and see where you will end up 😃 About the position sensors, they have bad reputation because the old potentiometers worked really bad and ware not consistent but the new magnetic hall sensors are really precise and nothing can go wrong with them! Then we are all to be blamed making that load cell and muscle memory such a huge myth where in reality there is no real muscle memory but only automated movements which are not just in pressure but also movement and can be perfectly polished in our brains 😃

Main problem of pedals for years, that 90% of enthusiasts don't have load-cell pedals. Real problem - in real life brakes fade, overheat under pressure and while jumping around and stepping on pedal drive does not have to mind angle precision. Solution is simple and elegant - soon for many manufacturers ;) (ffb)

Thank you for offering the solution to this "problem" in the video. However, I do feel like you're exaggerating a little bit, with costing "a lot of time". In most cases, you would actually prefer the progressive slight release of the brakes as you bleed off, which would make you faster. And regarding realism, it might not be 100% realistic, but then again, there are also no external forces such as bumps on the road, affecting your leg/foot on the brake pedal as your whole body is shaking and the G forces under braking in the real car. So this minimal change of brake power under the "same" input and the irregularity is so minor that I don't think it should be stated as a shortcoming of the pedals, especially since there are way more issues in the software of the sims we love. With that being said, I respect your opinion and love your reviews. :)

@chepilevski

9 ай бұрын

Sure it won’t matter much for some corners but it is worth for everyone checking how there pedal performs as I have seen some elastomers doing really bad job 🙈 This problem will matter for long braking distances mostly and is important to have the full control instead . But anyway, I have to point out this issue and people can decide if worth doing something about it or use it as it is 🤛

@-racingfan2014

9 ай бұрын

I like that the active pedals have gforce effect now that simulate the pedals coming to you during braking or moving away from you under acceleration.

@chepilevski

9 ай бұрын

@@-racingfan2014 wow, that’s crazy 💪

Just wondering, can you fit that cube controls wheel to a Simagic alpha mini wheelbase?

Thanks for the efforts. Great explanation and I learned a lot. A few points though: Before that, I sometimes cannot sound nice although I want to, sorry in adcance: 1- The "relaxation" only affects the strength measured, but NOT THE STRENGTH FELT IN YOUR LEG? interesting. You confirmed that the relaxation does NOT affect the position of the pedal due to becoming softer (only repeating this info to tell that I hear what you said). 2- The issue is significant for you sim racers. I did my calculations, you stay on the brakes for hundreds of meters (remember 150-100-50 marks) which means you use the brake for seconds and regardless of trail braking or anything else in the whole world, you simply need an authentic signal that conveys your input with fidelity in order to control the car. 3- This is not an issue for me, as I am so different from you guys (but this is a totally different topic). I am a realism and immersion geek. I do not do setup tricks or basically anything that I don't do in real life. You all think you are Max Verstappen. I am a simple guy who drive sh* boxes on race tracks. I humbly consider myself as a hard core car enthusiast and a skilled precise driver, yet, never have I ever in real life reached this razor edge laser sharp braking. I do not even understand why the car sometimes doesn't stop in real life because it can be dirt, oil, wind, pads temperature, tiny pump, slight difference in platform stabilization, ABS activation, oil pipe elasticity or simply me thinking I braked in the same point while not (in short: real life is not what you think, you do not fight same as hard and you do not search for a tenth of a second). I use sims to race road cars, cruise, drift, truck, fly...etc I don't want to be super fast in iRacing like you and then not able to drive any other sim or in real life. In other words, you guys are much better and faster than me, but let's move to some more interesting points (to you), hopefully. I digress. 4- I'll discuss the solutions you mentioned and some I suggest (not really, just food for thoughts). One of your suggestions was springs because they're stable which is a great idea, but I WOULDN'T choose it, simply because the progressive feel in the elastonomer feels more realistic to me which is the point of sim racing. Another suggestion of yours was hall sensor (or angle sensor). THIS POINT IS ABOUT TO MAKE ME CRAZY. My brain can't just decide. Let me start from the start, in real life, the pressure ( more accurately the force) of our foot makes the rotors pads push proportionately. So a load cell is realistic and fair because it makes the sim accurately deliver our input to the brakes, but given the issue you raised, let's discuss angle sensors; after learning what you explained about the elastonomer being progressive (increasing, none linear) in resistance, still measuring the angle can be 100% realistic ONLY IF either the brake is set up exactly like the real car (active pedals) or if the software had a very accurate algorithm to convert the pedal distance to force (again because the relationship is not linear and it's stiffer and harder to move the more the pedal is depressed). This is so convoluted and so hard for me to think about. 5- Finally, since you are the only sim racing KZreadr to do the effort of thinking, experimenting and teaching us (I'm serious, other KZreadrs mostly want to be little boys playing games while people donate to them), I hope you continue your tests and come with a part 2 video where you explain to us why are spacers and other accessories useful to help this inherit physical features in the elastonomers??? Do full hydraulic pedals have this issue (I think the more expensive ones measure the brake fluid pressure or movement or something). You mentioned in a comment that hydraulic accessories help calm down the elastonomer but does this mean slowing it down hence making the whole brake less responsive for sim racing? Do pneumatic have a similar issue? 6- Thanks. Sorry for the long text. You don't need to read it, it was crazy, lol.

Mate i'm so exited ! This week i'm gettin paid and i will purshace my P1000 or P2000 idk still but anyway it's time let's gooooo !

@chepilevski

9 ай бұрын

Those are existing time bro 🤩💪

So what you're saying is we all need active pedals! Fantastic! I just need them to release a more affordable version. :3

@chepilevski

9 ай бұрын

I’m very happy with the Simagic haptic solution man particularly for the money! Simucube tech is insane but way too expensive for most of us 🙈

The Honda Fire Blade has an ABS system that has the brake leaver disconnected from the break circuit. The feeling of the break leaver is supplied by a piece of rubber in the master cylinder. So Honda seem to have solved this problem.

@chepilevski

8 ай бұрын

😃

I remember I've started seeing some manufacturers start to make more medium to higher end pedals with stronger springs than usual and some people were praising many pedals using springs wich I found quite surprising but I tought, if it works, it works! I used to be very curious about upgrading from the fanatec V3s to the Simagic pedals with the motors but I'm afraid they will shut down support really quick for them like they did for the Simagic M10.

@chepilevski

9 ай бұрын

I don’t think Simagic will stop the support for the pedals as they don’t upgrade those any soon as they did with the DD bases

Excellent vídeo! Bought Simagic P2000 pedals = problem solved!

So here is an extreme example to see if I got what you're saying: I pressed the brake pedal too hard, in fact I floored my brake pedal to the floor, my tyres lock up, I should release some load off my brake pedal but I won't bother, because I know the elastomers will get soften soon so my braking force will weaken, hence my tyres will soon start rotating again.

I bought some springs today to mix and match with my Heusinkveld sprints see how it goes a great shout by the way 😉

@chepilevski

9 ай бұрын

Let me know how it goes buddy and what springs have you got 🤛

@pinpoint_uk

9 ай бұрын

@@chepilevskiof corse

Are there any ideas about the Fanatec CSP v3 and their behavior with the Performance Tuning Kit Elastomers ELADUR? Do they decrease in resistance too? Are there custom springs available as replacement? Thx!