It might be time to invest in a titanium hammer...that was A LOT of hand nailing 😂

@syntaxlies82

3 жыл бұрын

Next time use siding screws. Better for high winds that can rip the roofing nails out

@hsdesignstudio

3 жыл бұрын

@@syntaxlies82 I can see that being an issue in some places, very unlikely here. If we get winds that strong, I am more worried about shingles than the siding.

thanks for sharing your experience

Painting is why I'm here. Once vinyl is installed, you don't have to paint! Yay!

@hsdesignstudio

Жыл бұрын

It does finish off an exterior rather quickly 👍

best siding video

Thank you sir. Now I can do some siding for a client lol

Very informative. Thanks

@hsdesignstudio

3 жыл бұрын

Thanks for watching 👍

@jl9678

3 жыл бұрын

@@hsdesignstudio I'm putting up about 2k sf of vertical siding soon and your information was very helpful. I'll know to take my time putting up the trim

@hsdesignstudio

3 жыл бұрын

@@jl9678 the j channel is definitely the slowest part. Taking time to make the joints and corners line up nicely really brings it all together in the end. Good luck!

Wondering what your thoughts are on installing B&B horizontally? I'm redoing an 8x8 shed and bought left-over B&B (at a very good price) but it could leave me with a lot of waste pieces if I install it vertically. Any cons of going against the grain so to speak as I'm thinking of doing?

I'm planning to build a custom home with 1" of polyiso exterior insulation. Would I just use longer nails to attach to the OSB underneath? If I did strapping or rainscreen it would have to be horizontal to attach board and batten and I don't think horizontal rainscreen is recommended? Do you have any suggestions?

Looking to put up something similar on my cabin, I didn't quite see how you did the corners. Is there a special corner piece? Great video BTW, don't assume people are not interested 😉

@hsdesignstudio

3 жыл бұрын

Thank you! I did my corners a little differently, in that I used PVC trim instead of vinyl siding specific corners. You can see exactly how I did this in the previous episode here: kzread.info/dash/bejne/ZniOpdBmhKXSnNo.html

Where did you get the black siding? I can’t find it anywhere 🙃 I can’t find matching siding with J channel. Any help?

What is the vinyl cutter you used?

What is the name of the dark gray color looking vertical siding?

Great video. What size nail and nailing pattern/spacing did you use for nailing the siding?

@hsdesignstudio

3 жыл бұрын

Thanks. I used a standard roofing nail, spaced roughly every 16".

Would you need to install horizontal/diagonal strapping? How are you getting all those nails into studs? Are they all going just straight into the aspenite?

@hsdesignstudio

3 жыл бұрын

They are into 1/2" OSB. Siding screws are another option with more bite. However this garage is in a very sheltered location and high winds ripping the siding off are not a concern of mine.

I'm about to do a very similar install. I'd love to see how you transitioned the vertical board and batten and the horizontal siding. Any chance we can see it up close?

@hsdesignstudio

3 жыл бұрын

Hey Michael- I just used back to back J-channels of the various colours. They are running vertically, so I didn't see the need for a drip edge. Is your transition side to side or top to bottom?

@michaelwood218

3 жыл бұрын

@@hsdesignstudio Makes sense, I thought that's what I saw in a quick glimpse from another video. Thanks!

Nice going …. Question I have a slightly curved wall on one side of the house do you think board and batten would work around the curve?

@hsdesignstudio

Жыл бұрын

Depends on the material and the curve. But if you are using vinyl, it would work.

Which siding is this? Brand?

At 5min32sec where you finished the back wall of the garage, was there a j-channel along the top of that siding? Is j-channel needed there before you can start the peak section of siding?

@hsdesignstudio

3 жыл бұрын

Yes- There is one on top of the bottom board and batten, then a drip ledge, then the bottom j channel for the peak area. I use j channel anytime the siding ends. It hides the unfinished end.

@katgant

3 жыл бұрын

@@hsdesignstudio thank you! This has been really helpful!

@philwesa1766

3 жыл бұрын

@@hsdesignstudio try flashing the lower channel with a drip cap then re-start the horizontal siding using a starter strip you need a small space to lock the siding up but even with drilling holes the j won't get full of crud. Nice job mixing the textures.

I'm having a new home built and shopping for siding. What brand did you use in this video? I like the look of it. Thanks!

@hsdesignstudio

3 жыл бұрын

Hey Todd- This siding is Timbercrest Board & Batten by Abtco. The specific color is called Manor.

@toddk4115

3 жыл бұрын

@@hsdesignstudio Thanks man! Nice. I"m trying to find information on the width of each piece? Certainteed has most colors in 7" and some colors in 8". Mastic doesn't say what their widths are on board and batten vinyl. I guess I'll call these places up and email them, etc. thanks!! Plus some board and batten vinyl looks a little cheesy imo but not yours.

@hsdesignstudio

3 жыл бұрын

@Todd K No worries at all 👍 I believe each piece had a 7" exposure, plus roughly 1 inch for the tongue and nailing strip. I've installed a fair amount of vinyl siding, and I was really satisfied with this one. I've even had a few people walking by ask if it was metal siding because it doesn't have the "cheaper look" some vinyl can have. Good luck!

The j Chanel has holes to let water out but it hits cmu block and makes it into foundation. How to prevent it from that

@hsdesignstudio

2 жыл бұрын

The j channel shouldn't sit on foundation. It should hang over the edge so any water drains outside the foundation.

Where is the critical info? Where did you start from? Did you use a starter strip? Why did you install a J channel adjacent to your corner mold when it has an inherent indent to start your first strip? How did you butt J channel corners? How would you seam vertical to horizontal vinyl?

@hsdesignstudio

3 жыл бұрын

Thanks for watching. It isn't meant to be a how-to video. It's part of our Garage series building a garage from start to finish. But to answer some of your questions: I used J-channel at the corners because in the last episode you would have seen that my corners aren't using vinyl siding corners, but instead a PVC trim (I prefer the aesthetics of this). As for starter strips, every manufacturer has slightly different instructions. Some suggest an actual purchased starter strip, others suggest just cutting off the 'groove' from a piece of siding and using that. I don't think there is an inherently wrong place to start an install. As long as you move in a continuous direction, the install should go smoothly. I discussed my transition from vertical to horizontal in another comment, but I just used side-by-side J-channels.

@shug2795

3 жыл бұрын

@@hsdesignstudio Got it. Ok...I was going to do exactly what you suggested. Thanks for your timely response. God bless.

@hsdesignstudio

3 жыл бұрын

@@shug2795 no problem, good luck 👍

What brand of vinyl floor cutter did you use?

@hsdesignstudio

2 жыл бұрын

It's Bullet Tools

I have this same color and siding. After just a couple weeks of being installed it has circles and wrapped in areas. Have you had this issue with this color?

@hsdesignstudio

Жыл бұрын

None whatsoever- it still looks brand new. The tall black wall even faces straight south and gets the direct sun.

I’m looking for black vinyl board and batten can’t find it anywhere? Where did you find yours? Please🙏

@hsdesignstudio

3 жыл бұрын

This is Timbercrest Manor by Abtco. I bought it at Home Depot 👍

@brookbandeen4999

3 жыл бұрын

And abtco is cheap/crap vinyl!!!

Where did you get that b/b?? I'm considering doing my cape cod in this style. :)

@hsdesignstudio

3 жыл бұрын

This is actually from Home Depot. The manufacturer is Abtco- timbercrest board and batten.

@logan214

2 жыл бұрын

What color from them?

@logan214

2 жыл бұрын

NeverMind - just found it - Manor

Any update on how it held up

@hsdesignstudio

Жыл бұрын

The siding? It’s been great- no issues whatsoever. But I didn’t expect any, it’s vinyl siding after all.

Where can I buy this style siding. SOMEONE PLEASE HELP

@hsdesignstudio

2 жыл бұрын

This was actually just bought from Home Depot. Its Timbercrest Manor by Abtco.

Will black vinyl warp over time from heat?

@hsdesignstudio

3 жыл бұрын

That's a great question, and I guess time will tell. However, I think if it is installed correctly, allowing for the expansion and contraction of the siding, there shouldn't be any warping.

@stevewagner998

3 жыл бұрын

@@hsdesignstudio thanks for such a quick response. I was just curious because I looked into painting vinyl a dark color one time but they said the heat would cause issues. Maybe since yours comes from the factory that color it's different. Any ways looks great and hope to see updates! Good luck!

I like this color. But the manor color on there website look like a brown. Your color look like a deep blue gray. It’s beautiful

@hsdesignstudio

2 жыл бұрын

Definitely a deep slate-like black. I picked it based off the color sample chip and not the website photos.

Where can I order vinyl board and batten siding?

@hsdesignstudio

3 жыл бұрын

Most major home reno stores carry it/special order it, as well as many smaller local building shops. This was ordered from Home Depot.

What color grey is this???

@hsdesignstudio

2 жыл бұрын

Color/name is Manor. Its actually dead black in person. I have all the material info in another comment.

What color is that or name of the color

@hsdesignstudio

3 жыл бұрын

It is Abtco Timbercrest siding in the color Manor

What model of bullet vinyl cutter? They very in price.

@hsdesignstudio

2 жыл бұрын

Its the 9 1/2" EZ shear (I believe). This one was about $275 CAD

@michaelpeters1719

2 жыл бұрын

@@hsdesignstudio Thanks. I am doing vinyl siding and vinyl floor so it's worth the money.

@hsdesignstudio

2 жыл бұрын

Definitely is worth the money. It has saved me so much time during installation.

What color is that grey??? Thanks

@hsdesignstudio

3 жыл бұрын

It is actually black 👍- Abtco Timbercrest siding, colour is called Manor

@mikeoverholt5125

3 жыл бұрын

Really thanks, looks grey and that's the color I'm going 👍🍻🤛

you don't own a chalking for your botton J?

Is it black, I looked it up and the color sample doesn’t look black but your video looks black

@hsdesignstudio

3 жыл бұрын

It is a decent black, but not dark dark black. Next to say a black downspout (aluminum), it looks more dark charcoal. Black is a tough color as lighting and other blacks can really change how it is perceived.

@syntaxlies82

3 жыл бұрын

@@hsdesignstudio cool. I was leaning towards a certainteed that is similar but I think I’ll have to get a sample of each to compare. The internet sample of the one you did looks almost brown but obviously in your video it is blacked

@hsdesignstudio

3 жыл бұрын

@@syntaxlies82 definitely not brown- more like a slightly faded black when seen against a sharp true black

Didn't show how to start, finish under windows or stop at end.

@hsdesignstudio

3 жыл бұрын

It is not meant to be a tutorial on installation- there are plenty of 'how to's' already on KZread. This is part of a series following a garage build, and if people learn a thing or two along the way, then that's a bonus.

You might as well have had the camera across the street. Way too much of your presentation was too far away to be helpful to a DIYer trying to learn the process of installation. You need closeups. For instance cutting and fitting the J-channel. . All you did was say it was time consuming - show why. Also way too many wide shots of you on the ladder swinging a hammer. You’ve got to rethink your whole presentation style. My 2 cents!

@hsdesignstudio

2 жыл бұрын

Thanks. It's also not a how-to video, plenty of those out there.

@executivesteps

2 жыл бұрын

@@hsdesignstudio Well, reading the comments it sure seems a lot of viewers have “how to” questions? Anyway thanks for replying.

@executivesteps

Жыл бұрын

@U Betcha Consult a calendar. Halloween is still a month away.