The 5-minute Process That'll Save Your BMW Engine From Disaster
Автокөліктер мен көлік құралдары
►The oil system is arguably the most important in any engine. BMWs are susceptible to many services that interrupt the oil flow, which can cause oil to drain from critical engine areas. Especially on newer N54 and N55 engines, the brief lack of oil pressure can spell disaster for the bearings and other rotating components. Instead of rolling the dice after a repair, disable the injectors and prime your engine oil system.
00:00 - Intro
00:13 - BMW Engine Priming TSB Overview
02:00 - How to Prime the Engine
03:08 - Wrap-up
SUBSCRIBE: kzread.info?sub_c...
Get free parts from FCP Euro:
www.fcpeuro.com/page/lifetime...
Follow FCP Euro on:
/ fcpeuro
/ fcpeuro
/ fcpeuro
www.fcpeuro.com/
Пікірлер: 109
Gareth you have my respect dude, the before and after is unreal. Well done.
I saw the thumbnail and I just came to comment on how great Gareth looks. You look fantastic, congratulations!
Whoa, totally different Gareth from the one who showed me how to change the oil filter housing gasket on my N54, and water pump. Congratulations to you on achieving such success!
The level of slimming down that's been done is AWESOME!!! Congratulations for keeping it off.. Being Sicilian, it's tough to slow down on Breads and Pasta. LOL!!!!
Congraulations Gareth!!! Love the content from FCP!! 👏
looking great man!!
My dude's lookin' very trim, good job man. Also, great video as always, love from the U.K
Thank you! Just finishing up a big repair and was looking for this exact procedure!
@fcpeuro
Жыл бұрын
You are welcome!
Very valuable info! I wonder how many go without doing that procedure. Many people just don't care or don't know. Thanks!!
Nice tip on removing spark plugs, sounds like the starter isn’t straining at all
I’m about to do this on my n54 has been sitting for over a year , due to being out of state , just replaced timing chain with guide , cam ledge trays also new seals for the camshafts , new front main seal , everything on timing , just gonna keep those coils plugs injectors off , thank you for this , great video!
@fcpeuro
28 күн бұрын
💯👍
Gareth you looking good brodaa thank you for always helping me fix my f32 godbless
Hopefully, theoretically, mostly, and it should. Love it. That SIB replaced by SIB 11 02 20.
Gareth looks amazing!
Gareth, I almost didn’t recognize you. you look great!!!!! We are all proud of you for reaching goals! Now I need to step up my game haha! Have a great day!
To perform a real prelube ,a 20$ bug sprayer can be modified into a preluber and all you have to do is plug it into an oil pressure sender port right before starting. By modify, you basically jamb a piece of hose on the gun and add the needed fitting into the hose and add some clamps. Youll easily get 40-50psi pumping the sprayer by hand , that's plenty.
Is this recommended after the oil filter housing gasket replacement on N20 engine?
How about removing the fuse to oil pump? Or removing the coils and plugs?
No BMWs in the stable now, but this is a great logical recommendation for such low effort. Like NIKE, just do it.
great advice, i saw someone else doing this in a recent video after changing the oil housing gasket and even a prime for the hpfp after replacement, prime the pump so the engine isnt just sitting there looking for fuel...though in that case you dont turn the engine you just sequence the on off button a few times
@fcpeuro
8 ай бұрын
You could follow this procedure to prime the high pressure fuel pump to a degree. The only problem is air is still going to be trapped between the high pressure fuel pump and the injectors. This is only bled out once the engine starts. It's why almost all vehicles running a returnless fuel system stumble briefly on startup or require a few crank cycles to start after a fuel system repair.
Does this apply to all bmws ? I have a 08 E60 and wondering if I should do the same
Necessary to follow this procedure after a valve cover gasket replacement ?
just a heads up, if you have a high mileage car, might consider replacing the starter as well (if you took off the intake manifold for the ofhg job). I learned the hard way...
@idokwatcher2062
Жыл бұрын
just a heads up you might consider replacing the entire engine as well. because it's a BMW. I learned the hard way...
before this SB came out, I've always been in the habit (on any car) of start engine for about 15-30 seconds, shut off and look for leaks. If no leaks, start again, idle 1 minute, shut off and check oil level. Used this method after OPG (last year) on my E90.
@MrTheHillfolk
Жыл бұрын
A bug sprayer can be modified into a preluber,then just plug it in a sender port.
Lol, you spent 1 second explaining how to disconnect the injectors, and 60 seconds explaining how to turn the engine over. Well done!
Good idea to remove the spark plugs to reduce the load on the starter. The engine probably turns over more quickly as well.
wow man thats some weight loss! 🙏
Gareth, looking good. Like you lost 100lbs. How did you do it? (Replacing a N55 in our shop right not for this issue)
thanks for this! I’d assume it applies when changing the oil cooler as well, right?
@fcpeuro
8 ай бұрын
Yes. It would be a good idea to follow this procedure for replacing the oil cooler.
Hi this is Gary from ECS Euro
is that the 850 project filming in the background?
I error on the side of caution and prime as suggested, but i would love to see a side by side comparison. As others have mentioned, logic follows you should prime after an oil change and if the vehicle sits for extended periods, which almost no one bothers to do. How would both 150k mile N55’s look after a teardown, one primed always, one never? I also wonder if the suggestion has more to do with oil flow to the turbo than excessive rod or main bearing wear.
Following this logic, you should prime your engine after an oil change, because there is pretty much no difference from doing oil pan gasket to an oil change.
@bavarianautotech2096
Жыл бұрын
I am of the same thought!
@mcyeti86
10 ай бұрын
The bulletin says Oil filter housing, even though he said Oil pan. I think that's what he meant
@dorottyarendessy4953
8 ай бұрын
i think the same... sounds like overreacting a bit
@fcpeuro
8 ай бұрын
Not the same. An oil change does not interrupt the oil circuit the same way some of these other repairs will. If the car were to sit for 24 hours with the drain plug off the oil pan and the oil filter housing open, perhaps, but it's not as critical as it is for the oil filter housing, VANOS sprockets, oil pump replacements, etc.
@domkraggp9944
6 ай бұрын
Phew !! Relief.Ive done 2 oil changes on my new to me 435 while oblivious to this.While it doesn't affect oil changes , this is very valuable info for us die hard DIY'ers.Thanks Gareth
Very informative, when I saw your face i had to click this vid i was like ahhhh who is that
Same procedure for N54?
It would be helpful to show how the injectors were actually disconnected. Is it at the injector, at the hpfp? Is the disconnect an electrical or a fuel connection? Etc.
@reggiemhc
8 ай бұрын
Its a connector right by the injector/ spark plugs.. just disconnect them
I guess not clear to this fairly new DIY'er; is this something recommended to a basic oil change?
I pull the fuel pump fuse because I don’t like to mess with those delicate injector wires/connectors.
@johnnyblue4799
Жыл бұрын
There might be some pressure left in the system which will cause the cylinders to be soaked in fuel and dilute the oil film.
@jayparnes
Жыл бұрын
@@johnnyblue4799 pulling the fuse or unplugging the injectors amount to the same thing. Bmw does not specify pulling the spark plugs so I sense that the fuel pressure issue isn’t a concern.
@johnnyblue4799
Жыл бұрын
@@jayparnes I don't think pulling the fuel pump fuse, or disconnecting the injectors is the same thing, unless these run through the same fuse.
@jayparnes
Жыл бұрын
@@johnnyblue4799 they accomplish the same thing: no fuel delivery. Both are acceptable methods.
@johnnyblue4799
Жыл бұрын
@@jayparnes What I'm trying to tell you is that there's fuel under pressure on the fuel ramp and until that's gone, if you fire up the injectors, you'll spray it on the cylinder walls and wash out the oil film that lubes the cylinders until oil gets pumped again behind the pistons. Is that going to cause a lot of damage? Probably not, but why do it if it can be avoided? Dunno, maybe there's another fuse you can remove to stop firing the injectors?
Hi, I’m looking for Gareth?
As someone else mentioned, a little more detail on disconnecting the injectors would have been nice. And I didn't time them, but those "10-second" cranks seemed more like 5 seconds to me.
@fcpeuro
8 ай бұрын
You disconnect the injectors electrically, not mechanically. Simply pull the two pin electrical connector. This prevents the injectors from being able to inject fuel without disrupting the fuel supply unnecesarily.
Do you mean completely take out the spark plugs? Or just unplug the ignition coils?
Gareth can you just take out the fuel pump fuse ?
But on a serious note that goes for any engine. But I know it’s directed to BWM so I get it
Would it be easier to take out the fuel pump fuse?
@fcpeuro
8 ай бұрын
No. And the reason being is the injectors will still fire fuel and start the engine as there is residual fuel in the fuel lines leading to the HPFP which in turn will be pressurized and injected into the engine. Disconnecting the injectors electrically (removing the ability for them to pulse based on crankshaft movement) 100% prevents the engine from starting which is what needs to happen in this procedure.
Do you have to unplug all the injectors. My X5 it's hard to get to number 5 and 6 on a 6 cylinder engine without removing parts. What should I do? Any help?
@fcpeuro
8 ай бұрын
Yes. You do not want the injectors to fire (inject) fuel into the combustion chamber.
Anyone know what vent phone mount that is at 2:00 ???
Hi. Plse advise how to check the oil pressure level without an external oil pressure gauge connected to the engine.
@OGYELLOW
Жыл бұрын
MhD app
@fcpeuro
8 ай бұрын
Any scan tool that can read live data from the DME will be able to show oil pressure.
Did an N52 ofhg. I just pouring a quart of oil back down the housing then the rest of oil added normally. then started it. Did I do that wrong? Anything I can do now? Been driven for 200 miles since
@fcpeuro
8 ай бұрын
Generally, pouring oil into the oil filter housing doesn't do much. A majority of the oil poured into the housing goes through the drain back into the block. N52's do not suffer from problems as outlined where the N55 does. A lot of the N55 issues stem from the variable output pump and generally less oil volume in the entire oiling circuit. You are 100% okay.
@col3760
8 ай бұрын
@@fcpeuro perfect, thanks for the reply.
Shoot I did an oil filter housing job on my N55 without knowing this. Next time I guess
Recommended after oil change?
@tjshire
Жыл бұрын
I believe he said in the video that this procedure is recommended for any service "beyond" an oil change.
Isn't the reason for this the use of oil pressure assisted chain tensioners? With no oil inside the chain may become loose enough that it can jump timing, something that usually isn't possible.
@memyselfandIist
Жыл бұрын
Nope, air can make its way into the passages. On the N55, the tensioners are screw in, not oil pressure based.
Is this something that should be done after oil changes?
@OGYELLOW
Жыл бұрын
I would. Absolutely. The amount of oiling issue these have is stupid
@jayparnes
Жыл бұрын
Only if you’re one of those people who like to drain their oil overnight to get every….last…drop. This only applies to services that allow the oil to drain down for an extended period, about 45 minutes minimum.
Will this procedure be the same for an N54 engine?
@memyselfandIist
Жыл бұрын
N55 was the first that this was necessary. So no, N54 doesn’t need this process, unless fresh rebuilt or sitting a long time
@earthdaypinetrees8
Жыл бұрын
Oh thanks, even if the oil lines are opened?
3 years ago a had an OFHG (oil filter housing gasket) done on my 335xi by Winslow BMW of Colorado and they didn’t prime the engine a seized the engine. Took 0 responsibility.
@jonn9103
6 ай бұрын
I never know what to think with these stories because I hear them primarily with BMW owners. From a mechanical perspective it makes 0 sense since oil is designed to leave residual matter on the metal parts in order to mitigate metal to metal contact on start up. This is why a car can sit months at a time with almost all of the oil drained and be started up without seizing. When you change this gasket you literally still have residual oil all over the rest of the critical internal parts. Only thing I can imagine would be some sort of air pocket causing an issue and even that seems improbable. If so, seems like dropping a little oil into the oil filter housing would eliminate that risk.
You don’t have to hold the start button down?
@fcpeuro
8 ай бұрын
No.
Why not just pull the fuel pump fuse or relay? and quite frankly the motor is still dry when it is spinning without starting. I don't know if any of the code readers will read oil pressure without engine running. It would be good if you could read the pressure while the motor was turning over. It is a shame there is not way to run the oil pump while the car is off?? That would be the best scenario
Hmmm. I wonder if the guys at the small shop I go to know this. Something tells me they don't.
Absolutely terrible. Cannot believe that with electronic Oil Pressure this is needed.
Disconnecting the spark plug coils has nothing to do with compression.
@danmccarthy206
Жыл бұрын
@K M removing the spark plug would allow air to escape. Disconnecting the coil does not "release compression" . Someone needs to go back to school.
@danmccarthy206
Жыл бұрын
@K M i could have sworn he said wire, but he did say plugs. That makes sense now.
@bavarianautotech2096
Жыл бұрын
Exactly! That is why this is really NOT any kind of "5- minute process" for priming the oil system!
@fcpeuro
8 ай бұрын
We removed the spark plugs in this video to be gentler on the original starter motor (you can hear the engine freewheeling when cranked). The procedure from BMW outlines the need for an external power supply. We recognize that most DIYers are not going to have an external power supply, may have a weak battery, or a weaker starter motor. Removing the spark plugs from the cylinder head allows the engine to crank freely with no added resistance from compression which saves the starter motor + battery. It's an alteration to the procedure which takes into account not everyone is going to have the necessary equipment to do this "by the book".
This surely is a valuable tech-tip but it is certainly NOT a "Five Minute Process" as the title suggests! ... not if one removes spark plugs!! Me thinks a 10Amp Starter/Charger should be satisfactory toward aleviating battery discharge?
@kenendres8865
Жыл бұрын
The signal to the spark plugs was disconnected. Not the plugs them selves.
@bavarianautotech2096
Жыл бұрын
@@kenendres8865 Ken, Gareth did actually say he removed the plugs in order to facilitate not having the starter operating against compression in the cylinders! ... removing spark plugs is a laborious and time-consuming task!
@fcpeuro
8 ай бұрын
This is a quicker process if the spark plugs are not removed. The process as outlines by BMW does not require removal of the spark plug. In the interest of the car in question we wanted to be easy on the starter motor and battery. The starter not having to crank the engine against compression for a prolonged period of time is a choice we made (also doing other work at the same time). A good battery and providing ample cool down time in between cranks (plus a good external power supply) avoids the needs to remove plugs.
Thank You. Only training I've received was from "domestic ONLY mechanics" aka rednecks
This is all wrong. You prime by injecting oil through the oil pressure sensor thread using a manual pump or mechanic's syringe. Cranking does nothing.
+1
He looks like he lost 100 pounds
Ah yes, the procedures that exist and nobody follows. Also everyone that dont follow them do say that "bmws are sh1t". What a coincidence.
Man stop eating them burgers