Thanks for doing this review! We didn't have the guts to risk some CPUs on such a test. I think your application techniques looked reasonable and typical of what most users would probably do, I've also forgotten the sandpaper and I recommended it! Needless to say, I'm disappointed with your results and we'll have to revisit this. Also, I'd not recommend that your viewers use a permanent adhesive in place of a removable grease when possible as you separated these two surfaces with LESS damage than is usual! Thanks again and well keep in touch.

@LinusTechTips

4 жыл бұрын

Hey man thanks! I had a blast with this stuff and enjoyed the heck out of your video about it. Some people seem to be under the impression that we don't like the product but I think they've misunderatood the point of our test. We felt your video already covered its performance compared to other (commercial) thermal epoxy well-enough. Our test was just in response to our community's silly suggestion. For next time maybe I can make this more clear but I though by the time I took a hammer to the CPU it would be clear this wasn't a recommended application for this product!!! - LS Edit: one theory I had (after shooting) was that a much stronger clamp would give me more similar performance by squeezing out more of the excess epoxy. Unfortunately many of the "screw-down" type mechanisms that allow you to fine tune the clamping force are more prone to user-error. I wanted something brain-dead simple (and of course expendable haha).

@Tailslol

4 жыл бұрын

i wonder if you can make some thermal paste with some liquid metal like galium alloys and mineral oil.

@PapiSmerf

4 жыл бұрын

@@LinusTechTips Please do the internet a favor and send the rest of the epoxy over to Gamers Nexus so Steve can do an empirical set of tests on it.

@GreatMelonLord

4 жыл бұрын

@@Tailslol Sounds close to liquid metal minus the mineral oil

@Schradermusic

4 жыл бұрын

@@Tailslol Why not just use the liquid metal used in delidded CPUs?

But does it have a cute picture of a grizzly bear on the packaging? Didn't think so.

@hozairibrahimkhail5995

4 жыл бұрын

How are u so early?

@dukcy7450

4 жыл бұрын

It was unlisted

@nudle6327

4 жыл бұрын

@@CtrliPhones oh god i see what you did there

@seemeethanator1444

4 жыл бұрын

@RITA [FUCK ME] OPEN MY CANAL 🗿

@baukebrouwer5143

4 жыл бұрын

@RITA [FUCK ME] OPEN MY CANAL Are there bots on youtube?

Original title of this video: "Slim Bearded Daddy Shoots Greasy Load All Everywhere - you won't BELIEVE where it landed"

@alexdavison8256

4 жыл бұрын

Xenronnify thx

@lucasgtr7256

4 жыл бұрын

Damn... You made my Day:-)

@spidercubed9718

4 жыл бұрын

sponsored by Durex

@kxhul_ll

4 жыл бұрын

Maybe add gone wrong in brackets

@SuperficialNight

4 жыл бұрын

Im dying

edit: he has bought the license now. thanks! The license you got for OCCT doesn't allow commercial usage and you're using it for clear commercial usage. The OCCT team reached out to you and you have ignored them. What the hell LTT?

@thetrcg

2 жыл бұрын

Liking this for more visibility, let's do our part for the small devs

@xicofir3737

2 жыл бұрын

I want to see if LTT or Linus will even address this, or what argument will Linus use in the next wan show, to explain how what they this is totally legit and using adblocks is wrong.

@pradeepchinna5545

2 жыл бұрын

Well said brother, came here to exactly say this. Using Ad blocker is piracy but this fine.

@PennyStonks420

2 жыл бұрын

Replying to bump

@josemiguelfernandes4113

2 жыл бұрын

bump it up!!!

The syringes have a volume measurement marked on the side for mixing ratios.

@killzone866

4 жыл бұрын

what am i a science man that reads?

@jacobmeader8117

4 жыл бұрын

why doesn't it just come premixed

@EvilSiper

4 жыл бұрын

@@jacobmeader8117 hardens when you mix it

@bradleywhais7779

4 жыл бұрын

@@jacobmeader8117 because its an epoxy. It chemically hardens when mixed.

@Gallagher068

4 жыл бұрын

An Epoxy is two liquids that once mixed become solid and that process typically is irreversible, to sell it premixed would be to sell a syringe full of dry cement effectively. some epoxy manufactures have a work around to this with a double syringe so as you push down on the plunger the correct amount of epoxy liquids comes out both nozzles but that's very likely beyond the scale of what Tech Ingredients can set up

Just waiting for permanent CPU-Cooler combinations to show up on Ebay 🤦‍♂️

@auntiepha8343

4 жыл бұрын

Well played.

@elsasslotharingen7507

4 жыл бұрын

Don't tell Apple, they might enter the desktop market.

@cperka1017

4 жыл бұрын

@Zippydsm Lee As a guy who had to wrestle with his CPU for an hour trying to yank it from the motherboard... I don't

@loganatori6117

4 жыл бұрын

@@elsasslotharingen7507 i might get wooooshed, but apple does have a desktop

@ghausali4278

4 жыл бұрын

@@loganatori6117 r/woooosh

Linus: does that look about 2x the size of the other blob? Linus: ignoring the measurements on the syringes

@igameidoresearchtoo6511

3 жыл бұрын

in the end it shouldnt have performed THIS bad even if the ingredients were missed by half a blob

@greygunner

3 жыл бұрын

@@igameidoresearchtoo6511 Did you notice in both videos the resting temperature was 67/68?

@igameidoresearchtoo6511

3 жыл бұрын

@@greygunner no i didnt thanks for pointing that out i guess

I usually just fill my whole bathtub with thermal paste and completely submerge my whole pc in it. It had yet to exceed -48° i did notice a 92FPS drop due to not being able to see my RGB through the thermal paste, so i made sure to cover the entire bathroom in RGB lights to eliminate FPS loss. 10/10 most effective method so far. Highly recommended.

@anxiousearth680

2 жыл бұрын

"My goals are beyond your understanding" lol

@innacrisis6991

Жыл бұрын

make sure to leave some for yourself too, thermal paste is yummy

@Yo-ic2go

10 ай бұрын

I then get in the bathtub to to make sure my body heat isn't increasing the pc temps

I've been summoned.

@krishsatpati2476

3 жыл бұрын

Ahh Yes, Gamers Nexus has Joined the Chat

@daryl2328

3 жыл бұрын

two titans meet... as it was written

@naib1616

3 жыл бұрын

underrated comment

@Lazarosaliths

3 жыл бұрын

I think Steve need to show how to heat up the CPU with a torch, rather than a hot air pistol!!!🤣

@mazda2284

3 жыл бұрын

did you ever test this ?

I feel that disappointment on Linus's face when he realised he had just been dunking on a bad thermal solution for this, and that the narrative wasn't justified.

@biko9824

4 жыл бұрын

Kevin Ruan prolly a yt bot, better not interact with the comment!

This is the best advertising Aqua has had in ages methinks.

@mikejameson7678

4 жыл бұрын

'Don't say "methinks" ever again.' - Peter Griffin

@crimescene25

3 жыл бұрын

People that say methinks are neck bearded, fedora wearing, sword owning virgins.

@0bomberjack0

3 жыл бұрын

@@crimescene25 Wrong. Only chads who made 4 touchdowns in one game and won their team the championship use it.

@ThePeacePlant

3 жыл бұрын

I was looking for a comment to see if someone noticed the CD

@incognito3402

3 жыл бұрын

@@crimescene25 what you got against sword owners, huh? kzread.info/dash/bejne/fISClsmEadW1pNI.html

"I love sciency instructions written for scientists." "Im gonna use this plastic mcdonalds knife ." XD

Linus: Has syringe with cc markings Also Linus: eyeballs it anyway

@RandomFandomOfficial

4 жыл бұрын

Linus never told you about the time he was a nurse and saved the syringes after drawer blood. What?!

@WarthogDoctor

4 жыл бұрын

Came here to say this. Sometimes his cavalier solutions are useful, but sometimes they are just dumb (this being one of those times).

@DarrenC_1024

4 жыл бұрын

for a KZreadr, CC always means Closed Caption.

@ddpwe5269

4 жыл бұрын

@@DarrenC_1024 Funny, I had no problem understand the context on the sentence when using the term 'cc' properly to describe the units on a syringe. The more you know ;)

@MightYoungJoe

4 жыл бұрын

Yeah, Eyeballs @ 11:30, you know what's up, Eh

"You can make this at home" The tool and ingredient: **A factory**

@DumKump

4 жыл бұрын

_And a Laboratory made for gamma scientists_

@LocoMe4u

4 жыл бұрын

+ a short university degree in science later...

@LVRaivo

4 жыл бұрын

Diamond xD

@Jason-mv4go

4 жыл бұрын

I used to fix old overheating xbox red ring off death with artic silver.

@fattud615

4 жыл бұрын

You should have done **Factory noises**

Hey Linus, you gonna pay the dev for a license for that? You're using it commercially. The dev that makes that is one dude. He deserves to be compensated for your commercial use of his software.

@rcbasher101

2 жыл бұрын

Adblock=Piracy Commercial use of software without paying for it=fine Linus=Tool

@matthewboyer4212

2 жыл бұрын

@Tango Crunch defending him?

@SzymonWlazlowski

2 жыл бұрын

This

@draftingish4833

2 жыл бұрын

Wait what software? this is a workbench that won't be used for production? so, using a commercial license makes no sense, they may have a commercial license but choose to do what they do with windows where you they don't activate on every install.

Update: LMG purchased the license, nice LMG you should probably address the issue with the use of OCCT without a commercial license, seems very hypocritical to call adblocking 'piracy' and then abuse a license

@Hypotaksen

2 жыл бұрын

What a bunch of fucking hypocrites. Using a personal license for commercial use when they very well know they should have bought an enterprise license, and then blaming the rest of us for piracy because we don't want to get ads constantly shoved down our throats? Get fucked Linus.

@CyberdriveAutomotive

2 жыл бұрын

@@Hypotaksen Yeah, I was about to unsub for the ad block "pirating" video, but decided against it Now? Yeah, unsubbed

@Rresenden

2 жыл бұрын

@@CyberdriveAutomotive Have a good day sir

@SzymonWlazlowski

2 жыл бұрын

This

@Accuaro

2 жыл бұрын

Also piracy infers to do something illegal, it is not illegal to use AdBlock software.

Finally, a product that Linus can drop without having something bad happen!

@PapiSmerf

4 жыл бұрын

Clearly you've not used much epoxy and learned that it works like buttered bread, where your mixing paper always lands wet side down.

@bingplayz

4 жыл бұрын

@Millson Cleary all of what you said is true 🤣🤣

@dewy341

4 жыл бұрын

Gets glued to the floor

@TJWins225

4 жыл бұрын

And ssd's kinda

@CiDK

4 жыл бұрын

He'll find a way

8:40 if only you had a thermal paste applicator like The Verge!

As soon as you said the bond is permanent, I knew in my heart you were going to sacrifice an FX. Poor Bulldozer!

Please Linus, address the OCCT issue, you are one of the few people on KZread that I respect

@xicofir3737

2 жыл бұрын

That boat sailed sometime ago, with skechy sponsers like Raid: Shadow Legends, Nice Hash, etc. And then there's the pointless tiles, and misleading tumbnails.

@SzymonWlazlowski

2 жыл бұрын

This

@jasonhe54

2 жыл бұрын

@@xicofir3737 Hence why Rain: Shadow Legends was dropped soon after the community complained on WAN show. As for Nice Hash, I believe they addressed them talking about Nice Hash in their Norton Crypto Miner video.

That Aqua CD gives me serious 90's nostalgia vibes.

@98RandR

4 жыл бұрын

That brought me right back to my childhood

@rimpe

4 жыл бұрын

U and me both

@Nektopoulo

4 жыл бұрын

I guess we're all just barbie girls in the barbie world...

@ric_dk-9520

4 жыл бұрын

but why was it still wrapped?

@MDM242

4 жыл бұрын

90's nightmares....

I thought the title was “Tasting another KZreadr’s thermal compound” and the thumbnail you with chopsticks and the thermal paste on the end

@RandomFandomOfficial

4 жыл бұрын

Does artic mx 4 taste better than noctua?

@yuddpudd

4 жыл бұрын

@Random Fandom Only one way to find out!

@true_neutral3378

4 жыл бұрын

@@yuddpudd try not to die I guess

@weegle.

4 жыл бұрын

I.C. Diamond is the tastiest imo

@orated762

4 жыл бұрын

I know, i feel i was click baited.. but not.

Maybe linus should read the unskippable license agreement on OCCT before having high and mighty opinions on piracy

@SzymonWlazlowski

2 жыл бұрын

This

Wow I'm glad you made a video with Tech Ingredients! Please consider collabs with other science/DIY KZreadrs like Applied Science, Cody's Lab, etc!

Linus using a hammer and screwdriver on the cpu and cooler......When did he start working for The Verge

@aloykatos

4 жыл бұрын

The verge doesn't use screwdrivers, they hope their Swiss army knife has one.

@mdsysltd5573

4 жыл бұрын

At least he did not use "tweezers"

@Napster60

4 жыл бұрын

@@aloykatos They use fake news "zipties" and "tweezers" Gosh guys get it right..

@justsomeguy5470

4 жыл бұрын

@@Napster60 Don't forget the live strong bracelet

@bloonsgaming

4 жыл бұрын

@@justsomeguy5470 And the CPU applicator tool that everybody definitely uses

"Meaning this is more like a thermal epoxy" It literally is sold as thermal epoxy...

@hajmardi3658

4 жыл бұрын

Lmao true

@GlenUren

4 жыл бұрын

That's what I thought, soon as I saw 2 tubes to mix..

@maminparvaresh

4 жыл бұрын

Thanks for pointing this out. Look at Linus's reply to Tech Ingredients on this very video on top and you'll see his response, before reading that reply, I was thinking that it was a new thing made for better performance compared to thermal paste, but it isn't, it is just thermal epoxy and they have marketed as something that performs better compared to OTHER THERMAL PROXIES, I think Linus addressed this poorly, and I'd appreciate it if you could confirm this, because English is my second language and I'm thinking maybe either I didn't pay enough attention or I didn't completely understand his whole statement. Thanks in advance.

@DeosPraetorian

4 жыл бұрын

Some people seem to be under the impression that we don't like the product but I think they've misunderatood the point of our test. We felt your video already covered its performance compared to other (commercial) thermal epoxy well-enough. Our test was just in response to our community's silly suggestion.

@poiiihy

4 жыл бұрын

@@DeosPraetorian bruh use quotation marks or something

Ayo is that OCCT the free or the commercial license version?

I love that artic silver is still like the standard for a decent thermal compound after all these years. Not many things in the pc world stick around so long nearly unchanged.

@XX-121

2 жыл бұрын

nah dude, i use to think the same, i switched to Gelid GC-Extreme and dropped 6-7c off of cured as5 (100% load) AND it doesn't cure, it stays tacky forever. i had a prob removing a cooler that was stuck to the cpu when using as5 and ended up (acidentally) ripping the cpu out of the socket, luckily everything was ok and no pins broke.

seeing linus reading the manual feels like when spongebob read the Bag of Wind manual

@jamberrytastic

4 жыл бұрын

Step 1 Point bag towards CPU step 2 firmly plant feets on ground STEP 3 Instant cooling performance! step 4 PROFIT

Garbage Thermal Paste: 60c Noctua NT-H1 Thermal Paste: 59c okay...

@TechnoMinarchistBall

4 жыл бұрын

It'd probably be a larger difference if the temps got higher.

@joaquinninoortega156

4 жыл бұрын

@@TechnoMinarchistBall its like air cooler and water.

@RetroOkamii

4 жыл бұрын

The cooler was pretty capable for the chip tbh, it'd show more in a lower end cooler, however I think they're probably underestimating the thermal paste that's included with that cooler. Thermaltake's paste isn't *that* bad, not nearly as bad as that generic white paste you can get in bulk from Chinese ebay resellers. Stock thermal paste included on CPU coolers have even come a long ways in recent years.

@000jimbojones000

4 жыл бұрын

Nivea creme = about the same

@joeycooper93

4 жыл бұрын

Air cooler = barely run AIO = 4.9-5.1ghz of bulldozer goodness. My PC when I decided to go with a 9590 a few years ago.

Linus, you are using OCCT software without a commercial license. Please pay the independent dev for his hard work.

@damianmakarowski5323

2 жыл бұрын

Praise

@damianmakarowski5323

2 жыл бұрын

Praise

That's arguably the best Aqua CD you used as a desk. HOW DARE YOU?!

Generally agreed takes: "PC components are sensitive. Handle with care." Linus Sebastian:

@ashto46_playz44

4 жыл бұрын

シロキマl hgfh kulfis el DJ HD GM Bk vu

@thalente8074

4 жыл бұрын

@@anithakandy2852 Jeremy Clarkson: 🥺

@BagheeraRaceGamer

4 жыл бұрын

@@thalente8074 Then proceed to the spanner... ...with a hammer.

Even if this epoxy had PERFECT thermal transfer, it wouldn’t be worth gluing the CPU to the cooler to me.

@Rugg-qk4pl

4 жыл бұрын

Eh that cpu is worth less than the metal it's made of

@Bloodray19

4 жыл бұрын

Well, actually if you have a cheaper tower cooler, for example my Be Quiet Pure Rock, and I had like a 3600x which'll be powerful enough for a few years, and the epoxy would be absolutely perfect with conducting heat, i'd be gluing it on. For the gained performance, it's not such a bad thing. Heck, I bet for just a little extra you could sell it with the cooler afterwards

@remic2196

4 жыл бұрын

@@Bloodray19 why not spent the surplus price for this epoxy on a better cooler?

@mal2ksc

3 жыл бұрын

If you're going to epoxy on a cooler, then you seriously should think about de-lidding it anyhow.

@IceDragon-fj4vx

3 жыл бұрын

for consoles tho? 😎😎😎🤔

"Serious science" he says as he mixes it on his physical back up of barbie girl.

5:10 You can also quickly warm up the CPU by unplugging the fan.

@hunam3876

2 жыл бұрын

Why go easier route?

@petitkruger2175

2 жыл бұрын

that’s a tech tip

@LULU1422__

2 жыл бұрын

he was increasing ambient temps around the cpu

@anxiousearth680

2 жыл бұрын

@@LULU1422__ So that it heats up, turning the fan off does that as well

These intos are so interesting and well animated I've stopped skipping them.

@amogh3275

4 жыл бұрын

That is so true lol

New Tech Tip : Do not give Linus a hot air gun ever again.

@YTubechangeAccount

4 жыл бұрын

yeah, just stop the fan for a few mins to get it to heat up

I've got those thermal pad's in my laptop now. Based on watching your comparison video for thermal consideration. I like them and they actually help my laptop run about 10 degC cooler.

Pirating software - LTT sleep Using Adblock - Real ISH

Linus: “Andy, what’s gonna happen?” Andy: “Kaboom!” Linus: “Nooo” Andy saying what we all thinking

@berat700_

4 жыл бұрын

Time stamp?

@ahmedshuaib8144

4 жыл бұрын

@@berat700_ 10:08

@berat700_

4 жыл бұрын

@Ahmed Shuaib thank you

@thewriteinpresident

4 жыл бұрын

You’ll make your way… Releasing the Title of God of Pak-Toe does not mean I abandon my people of the plain… For I will always be your King of Angels and Demons, and She will always be The Queen of the Forgotten, The Lost, and those whom did not give into Hatred, Jealousy, Envy, or any of them SEVEN DEADLY SINS… Also, I am no longer The Commander for you must learn to command your selves, your souls, and your symbiots, and the SOLIDS can be guides, or The Solids can work as one with these EVIL SPIRITS and since we know there are TWO Type of Light, we The Society of nonmason will follow the Light of Truth - Justice - Wisdom while the FREE MASON Lodge Members will follow the Dead Light of Lies, Conspiracy, and Collusion...It is said, there is a TIME before the CEMENT Dries, and we are all stuck with the MACHINE PEOPLE and their NEW WORLD ORDER, so I would destroy all 5G Eugenics TIME LOOP Technology and Mechanization before these 192 U.N. FLAGS kill all We The People of the HUMAN RACE… If you want (COVID19) to be gone, and the make it be gone for the Animals do not have to WEAR A MASK unless it is the Muzzle on a raging Animal, and though we Flesh and Blood and Bones People are THINKING Animals in Corporeal Temporal TEMPORARY Carnal Bodies, do you wish to allow FRAT BOYS and FRAT GIRLS to live off your TAXES as Welfare Babies whom always tell you what to do cause their Daddy or Their Mommy is a FREE MASON Judge, City Council, School Board, or Preacher of this or that RELIGION in your home town that also makes them kids of Church People WELFARE BABIES whom live of the Donations and Gifts to Church Tithing to say: We Speak for IN GOD WE TRUST, and we will send you off to WARS to murder other nonmason be they Christians, Jews, Muslims, Hindu, Baptist Shiva and Sunnite, and all the rest.?.?.?.? The no longer give many to any POLITICAL PARTIES or RELIGIOUS ORGANIZATIONS Just as Christ Jesus showed the BANKERS run the CORPORATIONS that run the Religions and the Governments!!! After all, do not the CORPORATIONS Tell you to put on that SLAVE MASK EMPLOYEE, or you will not have a Job???? Do not these CORPORATIONS make the Weapons of Murder for your Military People to kill we the Tax Paying Citizens of our lands be we Dark to light skin no matter our Eye and Hair Color???? Then while should we go to these U.S. FLAG Hollywood to Bollywood TV Commercial ORGANIZATIONS - AGENCIES - ESTABLISHMENT when without our Welfare and Money no COMPANY can push We The People around!!! The CORPORATIONS did not make our FLAT Duel Earth called Mother Heaven and Father Earth, and all things from Perfumes to Gold and Silver to Diamond to Gems to Seeds bring for the things we need without INSPECTION or INSPECTORS saying, I need to Take your Temperature and do a Corona Beer Bat Snake TEST up your nose….. The longer you belong to the STOCK MARKET the longer you remain a SLAVE - Servant - Subordinate to Rapist, Pirates, and Thieves… I have learned many things in my life walk as The Teacher, and Christ Jesus Returned in the Flesh and Blood and Bones of an MORAL MAN with connection to the Esoteric World of the All Mighty Source of all Creation and all Destruction, and that is only a FOOL would want WAR when we can share the land, the sea, and the air as we once did when we were all Tartarian, and these Chaldean had no way to take our land, and air, and seas, but now we find ourselves trapped in THE DAYS OF NOAH over and over while Nuclear ATOM BOMBS caress the ICE WALL of our Celestial Sphere, and Trump and Putin and Xi put 5 Megaton Weapons on Jets and stand alone FLYING DRONES controlled by The EDISON Machine of FORCED LABOR Technology in Santa Barbara CALIFORNIA USA… Johnny Exodice End to the UNITED NATIONS [International Mafia] at mewe.com/i/johnnyexodice [///|||\\\] ++++++++++++++++++++++++++++++++

@leepicgaymer5464

4 жыл бұрын

The Write In President dafuq

“Does that look the same size? Do three more of those” LINUS USE THE DAMN SCALES ON THE SYRINGES! 😂

@blahorgaslisk7763

4 жыл бұрын

He started mixing up such a minute amount that the scales wasn't very useful. If he'd done it all in one go the scales would probably have worked though. From what I saw of the original video from Tech Ingredients they did apply the epoxy much thicker that what Linus did. That's also understandable as the components they used doesn't have a flat smooth surface like the CPU and the Cooler Master HSF, so it has to fill larger gaps and the slightly porous surface on that ceramic resistor.

@TimSheehan

4 жыл бұрын

@@blahorgaslisk7763 look at the scales on the syringes @ 1:00 there's no sane reason for not using at least that much out of that whole syringe, also the larger amount you use makes the measurement error relatively smaller so you'll be getting closer to the recommended 1:3 ratio for an accurate test

@csgas0

4 жыл бұрын

@@vola-2899 tech ingredients replied to this video and said the application looked OK

Cool to see you testing the Thermal paste from Tech Ingredients. You should probably ask them for some speakers to test too. They did some interesting work on refrigeration. Would be interesting to see a collaboration on high spec homemade cooling setup.

“Oh wow, that’s bent” cracked me up

"No harm, no foul" CPU literally had bent legs after that pullout.

@fuzziestsock

4 жыл бұрын

Well linus isn't known for his amazing pullout game.

@grn1

4 жыл бұрын

After doing something like that my CPU I replaced it and the MOBO* granted I know for a fact the CPU pins were bent to hell and back and there's no way I was going to go through and individually bend back each and every one. *Just in case there was a loose pin or something in the old one I didn't want to fry a new chip.

I'm gonna be honest with you Linus, about your beard. You're pulling it off really well, really suits you surprisingly.

@astonedcanadian533

4 жыл бұрын

It's his covid beard.

@TreblebullFPV

4 жыл бұрын

@@astonedcanadian533 Well Covid best be around forever... Otherwise we willl go back to: Linus grow a bread.

@hardergamer

4 жыл бұрын

As I wanna be Linus Iv grown mine as well...

@joanneswyckmans5921

4 жыл бұрын

A grew a beard months before anyone started to do that around me. Even the King (who is not around me, and I dont personally know or so) started to do it after me.

@Cinnabuns2009

4 жыл бұрын

respectfully disagree.

I love Tech Ingredients! So glad you did this!

Linus, I'm older then you and you've helped me with a lot of great tips, learned a tremendous amount from you on these videos. They being said, you should immediately pay for your copy of OCCT, and publicly apologize, do a video on why these things matter. If it's good enough fur you to use in these videos, it's definitely good enough to cough up the cash for.

@xicofir3737

2 жыл бұрын

At least I hope LTT acknowledged it in the next wanshow.

@puzzlejinx

2 жыл бұрын

@@xicofir3737 Linus is a known scumbag, do you really think he gives a shit?

@supra107

2 жыл бұрын

He has a legal obligation to pay for that software, he runs a business. It's not a garage project anymore where he could maybe get away from this.

@TT-zt3gq

2 жыл бұрын

@@supra107 Absolutely agree.

@tiromandal6399

2 жыл бұрын

@@puzzlejinx Not about you no tofu meatloaf.

Remember, Linus, just tell the inventory guys it was like that when you got it.

@shayan296

4 жыл бұрын

Hahahahah lmao

@stefanejegod8644

4 жыл бұрын

Linus: "No YOU broke it!"

I loved the glossing over how the “garbage” thermal paste was only 2 degrees off what the quality one did 😂

@leakingamps2050

4 жыл бұрын

This *was* on a CPU that throttled at a fairly low temperature. I've had CPUs that didn't throttle till 95 C, which is where the real difference would show up.

@Alobster1

4 жыл бұрын

This isn't thermal paste. This is thermal epoxy. They aren't intended for the same use cases. There is a reason thermal paste doesn't normally glue your heatsink to your cpu, because it doesn't have to. Thermal epoxy is for when you can't attach a heatsink conventionally.

@1014p

4 жыл бұрын

Well the performance paste didn’t throttle.

@Jehty21

4 жыл бұрын

Do the test again after a year or so. Most likely then "garbage thermal paste" would be way worse at that point.

@GtsAntoni1

4 жыл бұрын

Wrong CPU, and two degrees on air just for paste means a lot. When you have a delidded CPU under water, paste starts to matter a lot more.

I love the GD-900 at 4.8 Wk, i put it on all my computers, laptops and even the video cards. Stable and cheap! One 30 Gram bottle about $6-10. Also like all the top better ones too for a few degrees cooler but much more expensive and anything around 4-5 Wk will do a good job and you can see your laptop run cooler and fan slower even though you see around the same temp running. noticeably less heat coming from fan area. These sort of tests, you have to lock off the fan speed and throttle or it will adjust and you could see all same temps. Another channel tried thin to thick applications and found the temps come out about the same although you should aim for a thin even coat in theory. Loved your channel and all the advice and testing you do is a great help.

this reminds me that I still need to get an aftermarket cooler for my AM3+ board's northbridge. cpu temps are never bad when it's being pushed, but that dang northbridge really heats up just before a crash.

The Tech Ingredients channel deserves some extra attention, they make refreshingly informative content on a variety of subjects.

@oldbatwit5102

4 жыл бұрын

But can you trust it after watching this?

@MontyChimera

4 жыл бұрын

Yes! I absolutely love that channel, it was great to see this on LTT even if it wasn't amazing.

@spakecdk

4 жыл бұрын

@@oldbatwit5102 Linus compared it against thermal greases and not thermal epoxys, so the comparison isn't fair.

@markirving6397

4 жыл бұрын

spakecdk except that tech ingredients claimed it was better than arctic silver which is a thermal PASTE

@MrSopuli3

4 жыл бұрын

@@markirving6397 artic silver thermal epoxy is available on amazon uk

"This video is brought to you by AORUS" **Uses ROG motherboard**

@LocoMe4u

4 жыл бұрын

ROG is so crap aswel

@Sun6935

4 жыл бұрын

Do not quote on me on this, but I do not believe I ever saw Aorus during AM3 and AM3+ time period. Asus/ROG, Gigabyte(Not Aorus) and AsRock was pretty much the standard for those builds back in the day.

@jonaslinter

4 жыл бұрын

Sponsor and Content are separated

@xray5984

4 жыл бұрын

@@LocoMe4u What's bad about ROG? Also, *as well, and Louie never claimed AORUS is bad, so "as well" doesn't make sense. What is your favorite?

@louiefriesen

4 жыл бұрын

Xray Gaming thx. Under A Bridge Too Far, I think that ASUS, Gigabyte, ASRock and MSI are all great motherboard manufacturers. If you think ROG and AORUS suck, well then you don't need to get one if you don't want. I currently use an AORUS motherboard, and it works great. I'm generally neutral when it comes to buying a motherboard. I get what fits the budget, has the features I want, and has good reviews.

10:21 Linus: "Now I hate this. When you've got one dirty finger from what you were doing before and you've got to wash your whole hand." Me: Just take the glove off...

@bmoneymasta

4 жыл бұрын

It's a sexual joke i think

You should do a follow up showing how long each one takes to heat up, and how quickly they cool down.

Linus turned from a baby straight into a werewolf

@andrive

4 жыл бұрын

*werewolf Edit: c'mon man, I know it's a typical spelling issue, but I'd rather point it out so he learns how to properly spell it and stop spelling it wrong in the future. I myself am not a native speaker too. That's how we learn...

@firzt0

4 жыл бұрын

@@andrive cmon man, this is a global platform. basing from the name, he might not even be a native english speaker. dont be that guy

@geodacs

4 жыл бұрын

@@andrive he isn't. He is a WAREwolf, get it. NVM.

@darkomilosevic1659

4 жыл бұрын

@@geodacs as the guy above said this is an international platform. Dont be that guy. Nemoj biti taj lik

@cosmiclive4437

4 жыл бұрын

@@darkomilosevic1659 He... He was making a joke about the warehouse... C'mon man don't be that guy.

From "Hot Garbage" to "included generic stuff". That concluded quickly.

@clipsedrag13

4 жыл бұрын

lmao respectably after the end result

1:50 I like how the "inferno" CPU was the one I used to use lol, can confirm. Even with a big fat Noctua cooler it still got too toasty.

Bro I had my speakers at full when you started announcing the sponsor

As a danish guy, I have to question the still-sealed Aqua CD... And the fact that Linus used it as a ...well "dispossable" piece of film. Also, that's their debut album!

@littlefrank90

4 жыл бұрын

You should see what he did to his Cartoons' cd!

@zjostedt

4 жыл бұрын

Yeah, It would probably hold a bigger value than that PC to a collector :/ At least eventually.

@jakobhansen5477

4 жыл бұрын

Jeg er ikke sur.. jeg er skuffet

@mitchellhish2941

4 жыл бұрын

I loved that album when I was a kid. Ahhh the memories!

@alexandrecouture2462

4 жыл бұрын

Barbie girl...

2:10 Been a while since I've dragged the old Crosshair IV out of mothballs .... um I''m currently still using it to watch your video's.

@kennysboat4432

4 жыл бұрын

It’s like Linus takes older hardware for granted!

Wow. You really put that stuff on the best album of 1997.

hey that "included garbage" is actually the best out here since it is free :)

@greygunner

3 жыл бұрын

Best point made!

“When you got one dirty finger from what you were doing before” Hold up....

@headphone_

4 жыл бұрын

I've been holding up for 25 minutes now Can I now stop

@shitpostcentral8744

4 жыл бұрын

RJK7 no

@headphone_

4 жыл бұрын

@@shitpostcentral8744 my fingers starting to hurt :(

14:37 at least we get another clip to add to Linus Drop Tips..

That Aqua CD from our childhoods.. with Dr. Jone blessings!

That is the best use of an Aqua album I have ever seen.

Linus struggling to separate cpu and cooler 11. 1M subscribers "JUST DROP IT"

Anyone else going to comment on the Aqua Album he’s doing this on? Doctor Jones is deep within my childhood for some reason.

@whitewillow0

4 жыл бұрын

my imediate reaction was nooooo not on the Aqua album.... yeah its one of my guilty pleasures

@lordmmx1303

4 жыл бұрын

:D haha, same here. Doctor Jones. also Barbie Girl. still rockin till today

@Lupoalberto12It

4 жыл бұрын

It's looking for this comment!

@pvtpain66k

4 жыл бұрын

Happy boys and happy girls will be. Mmm, yeah, so haaaaaapy.

@zeldamaniac3188

4 жыл бұрын

Roses are Red was my favorite

I used thermal epoxy on my LSI 9260-8i raid card, glued the smallest water block I could find, which was a small 1"x1" one from Koolance. Card got so hot it shut my system down on air, afterwards it was getting the warmer water AFTER passing through the cpu + gpu, and it always stayed nice and cool. Under heavy system load it stays in the 50's. It's still glued on and running great 10yrs later lol

Glad to see that the noctua paste I get with my cooler is pretty much the best option

Tech Ingredients? I'm subscribed to them and they make some cool stuff! It's good to see them featured. EDIT: I would like to add that I use thermal epoxy on mounting heatsinks to the Raspberry Pi. I use regular thermal paste and epoxy, mixing them together at about a 60/40 ratio (60 being paste). It does way better than the thermal tape they come with. Thermal adhesives are used in situations where you need really good conductivity AND you need the heatsink to stick as there are no other mounting options. No one should be blasting Tech Ingredients for his creation and findings, and neither should anyone blast LTT.

@MaethorDerien

4 жыл бұрын

Yeah, that was exactly the use case I was thinking of is on something like a Pi where regular paste won't work well. The other option is thermal adhesive tape/pad which is much much worse than this. What would be interesting is to see a third party test vs arctic alumina which is the general competing product. Thermal epoxy isn't really that expensive though so I am not sure why he claimed it was expensive, I definitely wouldn't want to try making it myself though for the low cost of it.

That Aqua CD. That's my childhood in a CD case! ❤️😁

@realgeekay

4 жыл бұрын

me too. one of the first CD's I had as a kid.

@jacintomalfavon1491

4 жыл бұрын

As a kid, this & my Chumbawamba cassettes were the first I ever bought at Sam Goody on my way to rent a movie at Blockbuster 🤣🤣 Crap I'm old!!

I love the unopened Aqua cd as the mixing surface

Fun scrolling through new comments of this year old video. Very cool.

Tfw when Linus eyeballs measurements INSTEAD OF READING THE AMOUNT ON THE SYRINGE

10:16 Linus sounded like Unbox Therapy for a moment there

@theciponnescus

4 жыл бұрын

Agree

@deancadry3795

4 жыл бұрын

100%

@TheAlphaZulu

4 жыл бұрын

OMG, yes. I came to the comments section just for this.

that spiral cooler looks super neat! id shove that in my box

Your hair looks SO MUCH BETTER when it’s longer like this and not like a short, gel’d up middle schooler circa 2003. 😝

When you compete with Cryonaut and Gorilla Glue at the same time

@RichardGrim

4 жыл бұрын

Cryo glue

Linus: uses Aqua cd as mixing pad. Aqua cd: My oh my, do you wanna tell me why?

@Samvitch

4 жыл бұрын

I paused the video just to confirm my eyes hadn't played a trick on me hahaha

@andrewmurray1550

4 жыл бұрын

@@leocompany BARBIE girl!

@KylerJones

3 жыл бұрын

I'm just laughing at the fact that they had an Aqua CD just laying around in the office

@shaunbaltes8862

3 жыл бұрын

@@Samvitch i did too

@shaunbaltes8862

3 жыл бұрын

@@KylerJones and the fact its been sealed in there for over 20 years haha

Before he even said the processor I was thinking to myself "This sounds like a job for the FX series!"

@sovietbear3024

4 жыл бұрын

My first build had an FX and an r9 270x innit. Too bad the PSU/Mobo died in the move. Miss the ol' space heater. Still kickin around just wont post. Seriously though, my teenage bedroom was always like 5-10F hotter than any other room in the house.

@logan_page

4 жыл бұрын

@@sovietbear3024 I've got a PowerMac G5 with two dual core cpus, and it is litterealy equivalent to a space heater.

@ErksDemos

4 жыл бұрын

@@sovietbear3024 My first build also had an FX 8320 and a r9 270x xD, the GPU and the mobo died, but the CPU it's still working haha, and yeah my bedroom was way hotter than any other room.

@SyphistPrime

4 жыл бұрын

@@sovietbear3024 I ran an FX 6300 and 2x R9 270x CPUs in XFire. The thing seriously kept me warm in the winter when I would play GTA IV until 1-2 am. Now it is my high school best friend's wife's computer. The thing refuses to die despite changing hands 2 times now. The only changes it has had is it has an SSD now and I removed 1 GPU because of XFire support slowly dying. For what it's used for, the thing still runs well. I'm impressed it's still useful nearly 7 years later, especially knowing the FX line.

Its a two component adhesive, so its only on its purposed effectiveness when its hardened, just like the 2k-adhesive we use for threaded rods.

1:51 "The FX-8150, that was known for being an absolute inferno of a chip" Me on FX-8350 on stock cooler:

@butter5694

4 жыл бұрын

Same but I got the cooler master ml240r. It's dope for $80 and I don't go over 50°c

@YTubechangeAccount

4 жыл бұрын

@@butter5694 Yeah, I got a cheap $20 cooler with 4 heat pipes and a 80mm pwm fan and dont get past 52c until its 85f+ in my place at 4.3ghz (4.0ghz quad core in the summer)

@TinchoX

4 жыл бұрын

Pfft peasants: FX-9590 @ 4.7 Ghz (Stock speed) with an aftermarket cooler - Still hits like 69ºC under heavy load, and I've seen max of 76ºC

@martyflysandwich6810

4 жыл бұрын

Me too! But not stock cooler. FX-8350 on water cooling clocked at 4.8 GHz on all cores since it was new. Temps never over 60C.

@d3c0y39

4 жыл бұрын

Just upgraded from an 8350 50-54c in summer, 280mhz fsb 17.5x multi, 1.392v, 4.76ghz on water.

"Oh wow....that's bent." Best Linus Quote in awhile

Yessss I wanted to see how it would perform!!!!!

Is that OCCT purchased for commercial use?

15:03 Of course! Good old FX never dies!

4 жыл бұрын

True dat. 8.1Ghz

@CheekyChan

4 жыл бұрын

If I had a penny for the amount of FX and AM3 chips I was able to get working again I'd be swimming in a tub of psuedo copper zinc coins.

We're early, boys!

@LinusTechTips

4 жыл бұрын

What is this? Don't make me start spamming "last time I was this early, Snazzy still used a MacBook" crap on ur videos now! 😂😂

@ethcam8

4 жыл бұрын

@@LinusTechTips that is bruh moment

@Shaddow798

4 жыл бұрын

@@LinusTechTips no balls you wont

@code-grammardude5974

4 жыл бұрын

Yes

@ClassicSkye

4 жыл бұрын

@@LinusTechTips Lol

that cooler though, looks like something that would go in a jet

@exwarx3375

4 жыл бұрын

Ikr

That Aqua CD you mixed the thermal/epoxy on is a classic! you monster!

That Aqua CD brought back a lot of childhood memories xD

Me listening to Anthony pick the Noctua paste with zero hesitation. "A man of culture!"

@Quettesh

4 жыл бұрын

And there was little difference between that old crap included with the cooler and the Noctua. MX-4 is basically the same and cheaper. Don't be a fanboy when it makes you pay more for no benefit.

@iluvleo

4 жыл бұрын

​@ジョージ様 and the MX-4 could cure corona

@thewriteinpresident

4 жыл бұрын

You’ll make your way… Releasing the Title of God of Pak-Toe does not mean I abandon my people of the plain… For I will always be your King of Angels and Demons, and She will always be The Queen of the Forgotten, The Lost, and those whom did not give into Hatred, Jealousy, Envy, or any of them SEVEN DEADLY SINS… Also, I am no longer The Commander for you must learn to command your selves, your souls, and your symbiots, and the SOLIDS can be guides, or The Solids can work as one with these EVIL SPIRITS and since we know there are TWO Type of Light, we The Society of nonmason will follow the Light of Truth - Justice - Wisdom while the FREE MASON Lodge Members will follow the Dead Light of Lies, Conspiracy, and Collusion...It is said, there is a TIME before the CEMENT Dries, and we are all stuck with the MACHINE PEOPLE and their NEW WORLD ORDER, so I would destroy all 5G Eugenics TIME LOOP Technology and Mechanization before these 192 U.N. FLAGS kill all We The People of the HUMAN RACE… If you want (COVID19) to be gone, and the make it be gone for the Animals do not have to WEAR A MASK unless it is the Muzzle on a raging Animal, and though we Flesh and Blood and Bones People are THINKING Animals in Corporeal Temporal TEMPORARY Carnal Bodies, do you wish to allow FRAT BOYS and FRAT GIRLS to live off your TAXES as Welfare Babies whom always tell you what to do cause their Daddy or Their Mommy is a FREE MASON Judge, City Council, School Board, or Preacher of this or that RELIGION in your home town that also makes them kids of Church People WELFARE BABIES whom live of the Donations and Gifts to Church Tithing to say: We Speak for IN GOD WE TRUST, and we will send you off to WARS to murder other nonmason be they Christians, Jews, Muslims, Hindu, Baptist Shiva and Sunnite, and all the rest.?.?.?.? The no longer give many to any POLITICAL PARTIES or RELIGIOUS ORGANIZATIONS Just as Christ Jesus showed the BANKERS run the CORPORATIONS that run the Religions and the Governments!!! After all, do not the CORPORATIONS Tell you to put on that SLAVE MASK EMPLOYEE, or you will not have a Job???? Do not these CORPORATIONS make the Weapons of Murder for your Military People to kill we the Tax Paying Citizens of our lands be we Dark to light skin no matter our Eye and Hair Color???? Then while should we go to these U.S. FLAG Hollywood to Bollywood TV Commercial ORGANIZATIONS - AGENCIES - ESTABLISHMENT when without our Welfare and Money no COMPANY can push We The People around!!! The CORPORATIONS did not make our FLAT Duel Earth called Mother Heaven and Father Earth, and all things from Perfumes to Gold and Silver to Diamond to Gems to Seeds bring for the things we need without INSPECTION or INSPECTORS saying, I need to Take your Temperature and do a Corona Beer Bat Snake TEST up your nose….. The longer you belong to the STOCK MARKET the longer you remain a SLAVE - Servant - Subordinate to Rapist, Pirates, and Thieves… I have learned many things in my life walk as The Teacher, and Christ Jesus Returned in the Flesh and Blood and Bones of an MORAL MAN with connection to the Esoteric World of the All Mighty Source of all Creation and all Destruction, and that is only a FOOL would want WAR when we can share the land, the sea, and the air as we once did when we were all Tartarian, and these Chaldean had no way to take our land, and air, and seas, but now we find ourselves trapped in THE DAYS OF NOAH over and over while Nuclear ATOM BOMBS caress the ICE WALL of our Celestial Sphere, and Trump and Putin and Xi put 5 Megaton Weapons on Jets and stand alone FLYING DRONES controlled by The EDISON Machine of FORCED LABOR Technology in Santa Barbara CALIFORNIA USA… Johnny Exodice End to the UNITED NATIONS [International Mafia] at mewe.com/i/johnnyexodice [///|||\\\] ++++++++++++++++++++++++++++++++

So is ad block piracy but piracy isn’t piracy or what’s the deal Linus?

To soften epoxy, use the heat gun to heat up the parts. At some point it'll get soft enough to separate the parts. I don't think it'd be hot enough to damage the CPU, though it'd be way above acceptable running temperatures.

Hey, i actually had that same music CD when I was a kid lol

@pernielsen3445

4 жыл бұрын

Danish group, Aqua :D

@StaelTek

4 жыл бұрын

I had a VHS tape of them

@samratmitra1

4 жыл бұрын

Yes the CD stood out 😄

@samueltornberg

4 жыл бұрын

I still have it in a box somewhere :)

@acidrazor

4 жыл бұрын

ok boomer

Watching him hammer a CPU even an old one hurts my soul.

@SyphistPrime

4 жыл бұрын

I think he presumed it would've been dead after yanking it out of the socket twice. Still, that kind of tech gore hurts.

@Secondarian

Жыл бұрын

@@SyphistPrime Bulldozer deserves it.

LTT video: and this video brou- Me: *TAPPING SCREEN CONSECUTIVELY*

Dyson should invent a device with the ability to clean a single finger at a time.