Tensegrity Model (gravity and tension)
You can not possibly believe this!
Tensegrity is a term that is somewhat difficult to explain in a way that is easily understood without a model to demonstrate. This is an unconventional architectural method that seems to defy logic and is really hard to believe, even once you understand the concept. When I started this project, I had never seen anything like this I didn’t fully understand or appreciate the degree to which this would eventually boggle my own mind. With only screws, string, and wood, you too can create this really neato...thing! Your friends will insist there are magnets, springs, or some type of magic making it work. They will want one.
From what I could find, the first one of these tensegrity structures was first successfully demonstrated by a sculptor named Kenneth Snelson in 1949. There have been many different iterations of this idea since it was first thought of. Mine comes from a very short, and frankly, not very helpful, KZread video that showed the model and a hasty demonstration that barely covers the basics of how to make it work.
This seemed like a terrific, fun, relatively simple, and easy project to put together. It turned out to be quite a lot more difficult than I originally anticipated, so I’m going to show you in hopefully enough, but not too much detail how to make this happen. It’s a really cool piece for your office, a true conversation starter!
I started off with 3/4” square dowels but I’m sure my model could easily be scaled up to be built with 2x4’s (or other material) large enough to make it in to a table for your patio. I might do this in the future if you let me know you want me to in the comments section of this video. Once you’ve decided how large you want your model to be and you’ve made your cuts, all you need is string and screws to hold this thing together and turn your mind upside down.
Cut 6 pieces, all identical in length and size, with 60° angles in opposing directions on either side and align them to make your triangle bases. My side pieces are 6”, measured at the longest part. Cut two more pieces that are the same length as one of the sides on your base and put a 30° cut in the SAME direction on both sides of both pieces. I didn’t do this in my video(I only cut a 30° on one side), but I think in the end, this will give your model a more polished appearance. This will make the top of your upright level with the surface it is sitting on instead of being...well, 30° off, like mine is. Hindsight is 20/20, this is a modification I will make if I build any more of these.
Secure all your pieces together with 1” wood screws after you pre-drill your holes. Mark the holes for your strings and pre-drill those holes and 1/8” deep pockets for your knot heads to sit in. Sand and clean up as necessary. Use a toothpick or baby drill bit to poke your string through your holes. Follow the steps in the video to get your strings set. If you’ve got a better way this can be done, I would love to hear your recommendations.
Stay tuned for the entire life cycle of the monarch caterpillar and butterfly, a video I’ve been working on for over 5 months. I’ll see you soon!
Make sure and show support to the creators you follow by liking, commenting on, and sharing their videos. Every single time you do this, it helps us more than you know, especially small channels like mine. I appreciate your time.
Please follow my commissioned link below to get your discounted Starbond Premium CA glue supplies:
bit.ly/3za17Sl
Instagram: Curtis_Made_It
Пікірлер: 26
Way to go. I would like to be the first and say how cool this would look made of 6x6 rough cedar for the yard. Challenge?
@CurtisMadeIt
4 жыл бұрын
Cy Grindle Thanks for being the first to recommend a large one Cy. Don’t catch me saying challenge: ‘accepted’ too soon, but I’ll try designing something quite a bit bigger than this one. Your challenge has been tentatively accepted though.
That's NEATO!!! Now I want to build one.
@CurtisMadeIt
4 жыл бұрын
Justin Dickinson Make sure you’ve got plenty of time! This one takes a while but is oh so amazing when you get done.
Great idea for Christmas gifts!! Love the video CC!
@CurtisMadeIt
4 жыл бұрын
Cristina Garza Thanks CG! You are the best!
I always enjoy your work and you videos. Keep up the good work, C.Love!
@CurtisMadeIt
4 жыл бұрын
kobby818 Thanks a lot Kobby. People like you leaving comments like this really motivate me to keep going. I really appreciate your time and support, thank you.
I like it. It catches your attention. Cool process bro. Like the dual camera action.
@CurtisMadeIt
4 жыл бұрын
Loop Doc Thanks so much for your continued support Doc, I really look forward to your comments.
Nice! This is a really cool project!
@CurtisMadeIt
4 жыл бұрын
Litter Box Haha! I love you’re user name, that is awesome. Thanks a lot for looking and leaving your comment, I appreciate your time.
Looks like a nice piece that I'd use for a centerpiece. Got me wanting to try it myself! Always nice subtle videos that you make seem really non intimidating to try, keep it up!
@CurtisMadeIt
4 жыл бұрын
Irregularly RegularGuy I appreciate the feedback, compliments, and support Guy, you are the man! I’ll have a BIG tensegrity model coming sometime soon hopefully. It will be big enough to be a table on the patio!
"You never ever cease to amaze me King GOD has skillfully gifted you ||C* Love|| and I am blessed to be able to call you my brother & friend!"
@CurtisMadeIt
4 жыл бұрын
Michael Chaney Thank you my brother Mike. I appreciate your great compliments!
This looks so complicated! So fun to watch it being made! Keep it up! 👏
@CurtisMadeIt
4 жыл бұрын
Taylor Colbert Thanks so much Taylor, my first one was pretty difficult, but once I figured it out, the next batch went pretty quickly. I greatly appreciate your support!
Rad! Thanks for sharing.
@CurtisMadeIt
4 жыл бұрын
Chris Love Thanks for describing it perfectly Love, I appreciate it!
Awesome video.
@CurtisMadeIt
4 жыл бұрын
Danny Fuller Thanks so much D!
thanks a lot! very good video and explanations! subbed.
@CurtisMadeIt
4 жыл бұрын
shadee nicola So glad to hear it Shadee, I’ll make sure and keep the good stuff coming. Thanks for your support.
You will have 1k subscribers before you know it
@CurtisMadeIt
4 жыл бұрын
Starship FPV Thanks Starship, this is going MUCH better than anticipated. I’m going to keep at it and see where it goes.