team associated RC10GT clutch upgrade with the BuG
Жүктеу.....
Пікірлер: 75
@TruggyDriver696 күн бұрын
That's why we upgraded to the MIP clutch shoes back in the early 90's.
@thebug4046
6 күн бұрын
Absolutely! Sadly no longer made
@TruggyDriver69
5 күн бұрын
@@thebug4046 luckily I got about 6 or 7 of them nip.
@cousineddie74445 ай бұрын
I had a MIP 4n1 with inserts and no springs back in the 90's. Motors were much hotter back then so you needed all the bite you could get.
@thebug4046
5 ай бұрын
Last time I've seen one of those clutches was like 2 years ago on ebay for like 160 Canadian lol
@cousineddie7444
5 ай бұрын
@@thebug4046 That sounds about right. They were originally like $40-45 in the late 90's. It was tough to justify the cost upfront unless you knew someone else that had one. Same with the 360 Stinger kit. It was tough to spend $110 on that back then, but it came with a rear shock tower, and the balance and throttle response benefits were awesome. It's a shame the market is so thin now on Nitro stadium trucks.
@thebug4046
5 ай бұрын
@@cousineddie7444 i remember it man. We were like dam that's expensive. Until you look at it now and it's like 8x more 😂
@BigD_RC Жыл бұрын
Listen closely....lmfao that was hilarious
@michaeltaylor19859 ай бұрын
MIP clutch was the way to go back in the day with these.
@thebug4046
9 ай бұрын
Absolutely!
@stevebarr9604 Жыл бұрын
Those clutches look similar to what I use on my glow powered helicopters!
@russl3632 Жыл бұрын
lol!... the intro just knocked down your social credit score by a half point
@thebug4046
Жыл бұрын
And I absolutely could care less 🤣
@4wheelRCaddict
Жыл бұрын
All the info and you get off on that… whew internet must be a rough place for ya russ
@SlickTrickRC Жыл бұрын
Loving your videos guy. I'm learning a lot about nitro engines from you. I have a hoi savage21 that I bought used and refurbished and I just put a bigred in it. Loving my savage. Love your Content also. Good stuff. 👍
@thebug4046
Жыл бұрын
Thanks for watchin brother 🍻
@VinnyOkeefe
9 ай бұрын
Hey the bug what Allen head wrenches do you use
@speedgears1236 Жыл бұрын
Thanks for the video Bug404. I like the GT.
@thebug4046
Жыл бұрын
Thanks for watchin
@ronniesrc Жыл бұрын
Your videos are awesome and you sound older than you actually look I watched your live video you did just a little bit ago thanks for doing the videos you do
@thebug4046
Жыл бұрын
Haha thanks for watchin! 🤘🏻🍻💯
@stevebarr9604 Жыл бұрын
I ran those sh 6cc gas engines this evening and they run amazing with pump gas but they don't like that expensive stuff in the cans that is non ethanol! They have a weird looking glow plug though with a taper and no copper washer! Still trying to get the carburetor adjustment on the echo blower but those Amazon tools didn't work for me unfortunately!
@thebug4046
Жыл бұрын
Yeah they won't really run very well on Canfield because it's not gasoline it doesn't create the same catalytic effect as it's not the same kind of product
@robsrcinsanity1220 Жыл бұрын
Great video bro 👍🏻🍻
@thebug4046
Жыл бұрын
Thanks buds!
@bullmangotti Жыл бұрын
Classic video, and your funny as hell!
@thebug4046
Жыл бұрын
Thanks for watchin! Glad you enjoyed it! 🍻🤘🏻
@hpiedsavageed7608 Жыл бұрын
yeah I'm also taking a lil break with RC trucks for a lil while. Because of work and other stuff. BUT KBN! ;)
@thebug4046
Жыл бұрын
It's been quite difficult for me because of my work schedule so crazy I haven't really had any time to do it but things are starting to slow down a little bit which is good
@cyclonerc1625 Жыл бұрын
Kick A$$ vid. Thank's for Sharing Bug 🍻
@thebug4046
Жыл бұрын
Anytime! Thanks for watchin
@a2rc Жыл бұрын
Is the thing-a-mabob that makes the truck steer left and right a servo? LoL or something else? Also that head make the engine look wayyyyyy better! Looks like she has tons of compression and ready to go🔥💪🏻. Cant wait for a running vid. Thx Bug
@thebug4046
Жыл бұрын
Is hopefully tomorrow or the next day
@samsonight2721 Жыл бұрын
I'm running the sh slide version on my megatech .16 no complaints here 👌
@thebug4046
Жыл бұрын
Nice!
@nathanedmonds97964 ай бұрын
What spur/clutch bell combination have you found worked really good for the rc10gt I have a trx pro .15 as well
@thebug4046
4 ай бұрын
Same stuff as in the video
@wesleymorgan7894 Жыл бұрын
I got one mine back and another one
@David-069 Жыл бұрын
Hi Bug404 you know the pilot shaft you was on about well the part number for these is kyosho ab14 there on ebay.
@thebug4046
Жыл бұрын
Sweetness thanks for the heads up! 🍻
@David-069
Жыл бұрын
I’ve found the pilot shafts fit alot of different small block engines with the standard cranks.👍🏻
@joedoran699411 ай бұрын
Awesome vid whats the clutch part number I've got hold of the clutch nut bell and have a flywheel on the way i brought a traxxas clutch but looks diffrent too yours best way to explain it is a slightly bigger then the clutch in the MIP kit with the spring on the front i do have a mip clutch and fly wheel but its too small so i can't start the engine with my starter box with the conventional engine mount i have seen a trinity engine mount but the dudes on ebay are charging hundreds for em an this clutch idea was way cheaper
@thebug4046
11 ай бұрын
Hey man thanks for watching and it's just the standard Traxxas clutch. It's all going to look different then the MIP stuff. All Traxxas parts i believe it's the same clutch as a tmaxx 2.5 or rustler nitro sport
@joedoran6994
11 ай бұрын
@@thebug4046 awesome how well does the traxxas clutch grip I've also seen a hot racing 3 shoe kit I've got a spare clutch nut somewhere which is for my rs4 but has a groove for the springs too sit in might be something I'll experiment with the gt sometime be cool too somehow get a 3 shoe in there
@thebug4046
11 ай бұрын
@@joedoran6994 If it can pull a tmaxx with a modified 3.3 it will last in an rc10gt haha
@mbdulka9 ай бұрын
Throw a square up in there ... else good vid! 🙂
@thebug4046
9 ай бұрын
Thanks for watchin!
@Greenbear39 Жыл бұрын
🏁 I was wondering would it be possible to use a slipper clutch eliminater on that same engine and rc10gt2 chassis (black pan ) for a drag build. 🏁
@thebug4046
Жыл бұрын
Probably
@Greenbear39
Жыл бұрын
After the fact would it still benefit me to still do the upgrade that you did?
@thebug4046
Жыл бұрын
@@Greenbear39 if you can get the parts sure
@km4lkx497 Жыл бұрын
My revo keeps burning through clutch shoes... not even a gallon through it. Oof.
@thebug4046
Жыл бұрын
You running in tall grass?
@km4lkx497
Жыл бұрын
@@thebug4046 On asphalt mostly. I think it's due to a bad batch of springs or something from traxxas because post mortems reveal that the springs break and trash the clutch bell too. I am going to be buying a metal clutch kit for it soon. All my other traxxas clutches are what shipped from the factory.
@Moggmodels23 Жыл бұрын
Brilliant video mate great info 👍👌
@thebug4046
Жыл бұрын
Thanks for watchin!
@duanesapp49147 ай бұрын
I have tried this on my Rc10gt black tube and I had to move the motor out 3.5 mm/.125in to get the pinion and spur to line up. Have you had is issue?
@thebug4046
7 ай бұрын
Weird. No I haven't had that problem on my blue pans 🤷🏻♂️
@4wheelRCaddict Жыл бұрын
I missed it I guess but what flywheel did you use? Heard it’s just a traxxas clutch
@thebug4046
Жыл бұрын
Traxxas 2.5 flywheel
@4wheelRCaddict
Жыл бұрын
Appreciate that!!
@thebug4046
Жыл бұрын
@@4wheelRCaddict no worries buds 🤘🏻🍻🍍
@JMBlank1 Жыл бұрын
Hello bug, What is the part number for that flywheel? I need do to this for 2, RC 10s!! Thank you, JB
@thebug4046
Жыл бұрын
Just the factory Traxxas 2.5 3.3 flywheel is all you need
@dlaforce1963 Жыл бұрын
No spring on this clutch?
@thebug4046
Жыл бұрын
Yup it on the clutch just hard to see in the video
@danieldicarlo8676 Жыл бұрын
Do you have a the part number for the clutch shoe?
@thebug4046
Жыл бұрын
Clutch shoes for a Tmaxx
@danieldicarlo8676
Жыл бұрын
@@thebug4046 tra4146X?
@thebug4046
Жыл бұрын
@@danieldicarlo8676 i believe so. Basically all Traxxas stuff used the same clutch
Пікірлер: 75
That's why we upgraded to the MIP clutch shoes back in the early 90's.
@thebug4046
6 күн бұрын
Absolutely! Sadly no longer made
@TruggyDriver69
5 күн бұрын
@@thebug4046 luckily I got about 6 or 7 of them nip.
I had a MIP 4n1 with inserts and no springs back in the 90's. Motors were much hotter back then so you needed all the bite you could get.
@thebug4046
5 ай бұрын
Last time I've seen one of those clutches was like 2 years ago on ebay for like 160 Canadian lol
@cousineddie7444
5 ай бұрын
@@thebug4046 That sounds about right. They were originally like $40-45 in the late 90's. It was tough to justify the cost upfront unless you knew someone else that had one. Same with the 360 Stinger kit. It was tough to spend $110 on that back then, but it came with a rear shock tower, and the balance and throttle response benefits were awesome. It's a shame the market is so thin now on Nitro stadium trucks.
@thebug4046
5 ай бұрын
@@cousineddie7444 i remember it man. We were like dam that's expensive. Until you look at it now and it's like 8x more 😂
Listen closely....lmfao that was hilarious
MIP clutch was the way to go back in the day with these.
@thebug4046
9 ай бұрын
Absolutely!
Those clutches look similar to what I use on my glow powered helicopters!
lol!... the intro just knocked down your social credit score by a half point
@thebug4046
Жыл бұрын
And I absolutely could care less 🤣
@4wheelRCaddict
Жыл бұрын
All the info and you get off on that… whew internet must be a rough place for ya russ
Loving your videos guy. I'm learning a lot about nitro engines from you. I have a hoi savage21 that I bought used and refurbished and I just put a bigred in it. Loving my savage. Love your Content also. Good stuff. 👍
@thebug4046
Жыл бұрын
Thanks for watchin brother 🍻
@VinnyOkeefe
9 ай бұрын
Hey the bug what Allen head wrenches do you use
Thanks for the video Bug404. I like the GT.
@thebug4046
Жыл бұрын
Thanks for watchin
Your videos are awesome and you sound older than you actually look I watched your live video you did just a little bit ago thanks for doing the videos you do
@thebug4046
Жыл бұрын
Haha thanks for watchin! 🤘🏻🍻💯
I ran those sh 6cc gas engines this evening and they run amazing with pump gas but they don't like that expensive stuff in the cans that is non ethanol! They have a weird looking glow plug though with a taper and no copper washer! Still trying to get the carburetor adjustment on the echo blower but those Amazon tools didn't work for me unfortunately!
@thebug4046
Жыл бұрын
Yeah they won't really run very well on Canfield because it's not gasoline it doesn't create the same catalytic effect as it's not the same kind of product
Great video bro 👍🏻🍻
@thebug4046
Жыл бұрын
Thanks buds!
Classic video, and your funny as hell!
@thebug4046
Жыл бұрын
Thanks for watchin! Glad you enjoyed it! 🍻🤘🏻
yeah I'm also taking a lil break with RC trucks for a lil while. Because of work and other stuff. BUT KBN! ;)
@thebug4046
Жыл бұрын
It's been quite difficult for me because of my work schedule so crazy I haven't really had any time to do it but things are starting to slow down a little bit which is good
Kick A$$ vid. Thank's for Sharing Bug 🍻
@thebug4046
Жыл бұрын
Anytime! Thanks for watchin
Is the thing-a-mabob that makes the truck steer left and right a servo? LoL or something else? Also that head make the engine look wayyyyyy better! Looks like she has tons of compression and ready to go🔥💪🏻. Cant wait for a running vid. Thx Bug
@thebug4046
Жыл бұрын
Is hopefully tomorrow or the next day
I'm running the sh slide version on my megatech .16 no complaints here 👌
@thebug4046
Жыл бұрын
Nice!
What spur/clutch bell combination have you found worked really good for the rc10gt I have a trx pro .15 as well
@thebug4046
4 ай бұрын
Same stuff as in the video
I got one mine back and another one
Hi Bug404 you know the pilot shaft you was on about well the part number for these is kyosho ab14 there on ebay.
@thebug4046
Жыл бұрын
Sweetness thanks for the heads up! 🍻
@David-069
Жыл бұрын
I’ve found the pilot shafts fit alot of different small block engines with the standard cranks.👍🏻
Awesome vid whats the clutch part number I've got hold of the clutch nut bell and have a flywheel on the way i brought a traxxas clutch but looks diffrent too yours best way to explain it is a slightly bigger then the clutch in the MIP kit with the spring on the front i do have a mip clutch and fly wheel but its too small so i can't start the engine with my starter box with the conventional engine mount i have seen a trinity engine mount but the dudes on ebay are charging hundreds for em an this clutch idea was way cheaper
@thebug4046
11 ай бұрын
Hey man thanks for watching and it's just the standard Traxxas clutch. It's all going to look different then the MIP stuff. All Traxxas parts i believe it's the same clutch as a tmaxx 2.5 or rustler nitro sport
@joedoran6994
11 ай бұрын
@@thebug4046 awesome how well does the traxxas clutch grip I've also seen a hot racing 3 shoe kit I've got a spare clutch nut somewhere which is for my rs4 but has a groove for the springs too sit in might be something I'll experiment with the gt sometime be cool too somehow get a 3 shoe in there
@thebug4046
11 ай бұрын
@@joedoran6994 If it can pull a tmaxx with a modified 3.3 it will last in an rc10gt haha
Throw a square up in there ... else good vid! 🙂
@thebug4046
9 ай бұрын
Thanks for watchin!
🏁 I was wondering would it be possible to use a slipper clutch eliminater on that same engine and rc10gt2 chassis (black pan ) for a drag build. 🏁
@thebug4046
Жыл бұрын
Probably
@Greenbear39
Жыл бұрын
After the fact would it still benefit me to still do the upgrade that you did?
@thebug4046
Жыл бұрын
@@Greenbear39 if you can get the parts sure
My revo keeps burning through clutch shoes... not even a gallon through it. Oof.
@thebug4046
Жыл бұрын
You running in tall grass?
@km4lkx497
Жыл бұрын
@@thebug4046 On asphalt mostly. I think it's due to a bad batch of springs or something from traxxas because post mortems reveal that the springs break and trash the clutch bell too. I am going to be buying a metal clutch kit for it soon. All my other traxxas clutches are what shipped from the factory.
Brilliant video mate great info 👍👌
@thebug4046
Жыл бұрын
Thanks for watchin!
I have tried this on my Rc10gt black tube and I had to move the motor out 3.5 mm/.125in to get the pinion and spur to line up. Have you had is issue?
@thebug4046
7 ай бұрын
Weird. No I haven't had that problem on my blue pans 🤷🏻♂️
I missed it I guess but what flywheel did you use? Heard it’s just a traxxas clutch
@thebug4046
Жыл бұрын
Traxxas 2.5 flywheel
@4wheelRCaddict
Жыл бұрын
Appreciate that!!
@thebug4046
Жыл бұрын
@@4wheelRCaddict no worries buds 🤘🏻🍻🍍
Hello bug, What is the part number for that flywheel? I need do to this for 2, RC 10s!! Thank you, JB
@thebug4046
Жыл бұрын
Just the factory Traxxas 2.5 3.3 flywheel is all you need
No spring on this clutch?
@thebug4046
Жыл бұрын
Yup it on the clutch just hard to see in the video
Do you have a the part number for the clutch shoe?
@thebug4046
Жыл бұрын
Clutch shoes for a Tmaxx
@danieldicarlo8676
Жыл бұрын
@@thebug4046 tra4146X?
@thebug4046
Жыл бұрын
@@danieldicarlo8676 i believe so. Basically all Traxxas stuff used the same clutch
@danieldicarlo8676
Жыл бұрын
@@thebug4046 thankyou
@thebug4046
Жыл бұрын
@@danieldicarlo8676 no worries
🙈🤣🤣🤣🤣