Always a joy to watch, I have some catching up to do with your vids .. I am thinking of doing the trailer in reverse, .. turn the flat bed into a box van .. or / and make a new bed from scratch, and increase my trailer fleet .. Great vids and commentary Teri, you are a star.

@TeriWilde

4 ай бұрын

I enjoy building these truck and I like telling people what I do 👍

@RCmodeleng

4 ай бұрын

And you succeed on both counts, your expertise and experience applied to your methodical approach is inspiring, the commentary second to none. well done and keep it up, most appreciated. @@TeriWilde

Your videos are some of the best I've found for Tamiya Trucks - thank you , and have subscribed.

These videos have been so awesome keep them coming!

@TeriWilde

3 жыл бұрын

I'm glad you've enjoyed it as much as I've enjoyed building it.... I just need to get to the RC clubs and run it with the other 3 movies trucks. hopefully before I start the next one.

@rcjackiemack728

3 жыл бұрын

@@TeriWilde would be great to. It'll be a great movie truck photo

Nice work well done looks good 👍

Hi Teri, thank you for sharing with us the lights for the trailer. I’m in the middle of building the Scania R620, MFC-03 and Ive got a trailer too. I’m looking at perhaps even running my own wiring loom for the lights, especially as there are only 4 LED’s. As Jeremy Clarkson would say, ‘how hard can it be’ 🤣😂. Great insight to how to build a trailer too. Subbed too. Take care, keep well and all the best 😉😊😉

@TeriWilde

2 жыл бұрын

I have drawn a diagram showing the MFC outputs for the trailer light socket and plug. "How hard can it be" usually ended up being a disaster for Jeremey Clarkson if I remember right... 🤣

Ms Teri....... I GOOFED!! 😐🙄. I did NOT fit the LEDs through that rubber donut, before running the Wires, including side Running Lights, fitting the LEDs in the Bumper, fitting the Bumper and sticking the floor down!! 😭😳😵 I'm NOT pulling it all apart. This might call for some ingenuity..... OR guesswork! Right, I'm not even sure I want to stick that big, odd coloured plug on my finished, Lacquered, BLACK Front Panel anyway. I used your trick of fitting the Trailer Light Socket in the "Diamond Plate" Panel in front of the 5th Wheel. 😉👍👍 Thanks! So much better than on top of the Sleeper, which just looks DAFT to me.😵 I had also JUST done what you did with the Rear Tandem Axle - moved it back one hole! Great Minds? And I'm only done with the Bottom Panel.... But I used RTV Silicone in the panel grooves. Not only stopped the rattles, but also keeps the side Rails from pulling outward! I believe that I may leave the side Panels loose. It's a 70's Trailer.... It NEEDS some rattles!! 😂😜 Oh, and I like that "patina" Bumper. Adds character, AND it was the 70's... Drivers didn't much bother with their Trailers - and likely BASHED a Loading Bay or three!!! LOL! One question (only because I forgot the other six!!), have you ever tried fitting the Mud Flaps directly to the Bumper wire covers?? Thank you Teri! Again, quite informative.

@TeriWilde

3 жыл бұрын

I haven't tried fitting the mud flaps to the wire covers but I think I'm going to use some rear flap hangers from a Tamiya kit for this trailer... I'll see how I like it when it's driving around as to whether I'll fit mud flaps to it or not. and I once built a trailer and forgot to fit the rubber bung in the font panel so I just fitted a rubber grommet and then covered it with a small box. On my BJ McKay and Snowman trailer I fitted a home made fake reefer unit which covers that hole, not sure if you can see it in my Dayton wheel videos but the trailer lead come from the bottom of the reefer unit.

@CarminesRCTipsandTricks

3 жыл бұрын

Hey.... If the bog standard Tamiya Flap Hangers work, I'd rather go that way. It would look much better. We are thinking alike!! 😊 I'm making a Refrigerator Unit for my Trailer out of Plastic Sheet. I also made an Air Reservoir Tank, rolling Plastic into a tube, and using scrap Buggy Headlight Covers for end caps!! 😁

@TeriWilde

3 жыл бұрын

@@CarminesRCTipsandTricks I've checked my spares box today and I have 2 brand new sets of hangers, I'm going to look at fitting them to the trailer this weekend... 🙂 I'll also showcase reefer too... 👍

Hello, great trailer and great vid and love your channel very beautiful looking to pick one up like yours as well but in the process of building a cabinet for it, would you kindly be able to measure the dimensions length width and height of it of hauler and trailer from head to toe so I know how big to make my cabinet? Thank you

Simple but effective

@TeriWilde

3 жыл бұрын

keeping it simple is sometimes more than enough 😎

def fit the mud flaps and was it to early to put the chrome lady badges on them? what about useing the molotow chrome pen on the bumper this is by far a easyer build than the reffa trailer ....man that thing is like building the truck itself. i need to take mine apart at some point as i put the coupler release on the wrong side so i just taped it on until i can screw it down

@TeriWilde

3 жыл бұрын

I'm not sure what year the chrome lady mudflap weights came out. But I will leave them blank until I can think of a cool and relevant logo to put on them

Hello, you did not mount the chrome fenders?

@TeriWilde

Жыл бұрын

the American trailers in the 70s didn't have the chrome fenders, just mud flaps, which is why I left them off. plus they don't fit after I moved the axles back ½inch.

Put a little bit of tamiya grease onto screw before you put it in

Hi mate great video where do you get you leds from. Do they have built in resistors also what volt do they work at I want to add leds to my mfc would these work.

@TeriWilde

Жыл бұрын

I use added 5mm Red LEDs that I got from my local electronics store, no resistors used... it's just a simple straight swap. I did a little video of the change a while ago → kzread.info/dash/bejne/eHygyplwo5POh6w.html