Today we swap in a set of Rhino 2.0 rear axles on a 2018 RZR turbo. Different years and models should be the same.
Жүктеу.....
Пікірлер: 16
@akjason47343 жыл бұрын
Some great tips and tricks in this video thank you!
@utvoutlaws6652
3 жыл бұрын
Thanks for the support 👍
@ThorRider00224 жыл бұрын
Great video!! Good explanation!!
@utvoutlaws6652
4 жыл бұрын
Thanks :) dont forget to subscribe for more videos moving forward.
@ahmadtlaib83424 жыл бұрын
u do good job my friend
@USAIII-bs9cj Жыл бұрын
Thanks for the tips on the install, I just put 2 new Rhino 2.0 rear axles on my '16 1000XP about a week ago and I love 'em....hate to critique but you should have stuffed a rag or something in your diff opening while you were grinding....ok rant over,,,continue,,,🙃
@tpaulmusic2 жыл бұрын
Where is the best location to jack it up? I’m currently in the process of removing an axle… the trailing arm likes to sway. Lol I’m thinking about moving the jack to the back middle but wasn’t sure what the most secure spot is.
@utvoutlaws6652
2 жыл бұрын
So we normally take a block of wood and put it on top of a floor jack and jack up from the center on the skid plate near the front or rear of the machine and then you can get it up enough to take the tires off and peel everything apart Hopefully this helps thanks for watching
@Posibrian3 жыл бұрын
Some limit straps would be best if you're jumping it.
@utvoutlaws6652
3 жыл бұрын
A couple vids later we installed just that. Thanks for watching!!
@rodneybrown11223 жыл бұрын
Did you have to take off your skid plate to swap out your axles?
@utvoutlaws6652
3 жыл бұрын
No we didn’t Thanks for watching
@cscheidt13 жыл бұрын
So how are they holding up?
@utvoutlaws6652
3 жыл бұрын
Perfect so far!! It seems the key is not to stay on the throttle when landing off a jump.
@cscheidt1
3 жыл бұрын
@@utvoutlaws6652 Ya, that seems to be pretty much typ. of any axle. I was just wondering if these rhino 2.0's are really any better than OEM.
Пікірлер: 16
Some great tips and tricks in this video thank you!
@utvoutlaws6652
3 жыл бұрын
Thanks for the support 👍
Great video!! Good explanation!!
@utvoutlaws6652
4 жыл бұрын
Thanks :) dont forget to subscribe for more videos moving forward.
u do good job my friend
Thanks for the tips on the install, I just put 2 new Rhino 2.0 rear axles on my '16 1000XP about a week ago and I love 'em....hate to critique but you should have stuffed a rag or something in your diff opening while you were grinding....ok rant over,,,continue,,,🙃
Where is the best location to jack it up? I’m currently in the process of removing an axle… the trailing arm likes to sway. Lol I’m thinking about moving the jack to the back middle but wasn’t sure what the most secure spot is.
@utvoutlaws6652
2 жыл бұрын
So we normally take a block of wood and put it on top of a floor jack and jack up from the center on the skid plate near the front or rear of the machine and then you can get it up enough to take the tires off and peel everything apart Hopefully this helps thanks for watching
Some limit straps would be best if you're jumping it.
@utvoutlaws6652
3 жыл бұрын
A couple vids later we installed just that. Thanks for watching!!
Did you have to take off your skid plate to swap out your axles?
@utvoutlaws6652
3 жыл бұрын
No we didn’t Thanks for watching
So how are they holding up?
@utvoutlaws6652
3 жыл бұрын
Perfect so far!! It seems the key is not to stay on the throttle when landing off a jump.
@cscheidt1
3 жыл бұрын
@@utvoutlaws6652 Ya, that seems to be pretty much typ. of any axle. I was just wondering if these rhino 2.0's are really any better than OEM.