Suzuki Swift - Front Brake Disc and Pad Change
Автокөліктер мен көлік құралдары
Suzuki Swift 1.3 (G13BA, Hatchback, 1996)
Suzuki Cultus, Holden Barina, Geo Metro, Pontiac Firefly, Chevrolet Sprint, Suzuki Forsa, Suzuki Amenity, Suzuki Esteem, Maruti Suzuki, Chevrolet Swift, Chevrolet Forsa, Subaru Justy
Brake pad: Textar
Brake disc: Brembo
G10, G10T, G13A, G13B, G13BB, G13K, G15A, G16
Пікірлер: 28
Hey there! I uploaded a new brake replacement video following your suggestions. Check it out! bit.ly/s40rearbrake
Excellent video, thank you
Good job. You might consider some new steps in the future. Clean the hub face with wire brush and add copper paste. Do the same to the screws that hold the disc. Where the pads touch the bracket, clean with wire brush and add a bit of copper paste. Take out the guide pins, clean with clean cloth, check for wear and add silicone paste. Add copper paste to the bracket bolts and caliper bolts. Avoid using a vicegrip to push the brake in. It can damage the rubber boot. That way, no part will ever rust weld or not retract correctly. Keep up the good work!
@LukeModsxd
2 жыл бұрын
Thanks for the tips! I’ll use these methods on the next maintenance
@steve75112
Жыл бұрын
oh be quiet or make your own video
@LukeModsxd
Жыл бұрын
I just made a new video, If you could check it out, it would be awesome! I followed your helpful advices!
@b4tm4nrubin33
5 ай бұрын
@@steve75112the dude has a point. If you don’t grease between the clean hub and new disc it’s gonna rust solid and make job 10x harder to get it off next time
@kuengyal23
2 ай бұрын
He’s doing a dodgy brake job mate lol
gutes video, have a nice day my boy
Thanks Bro. Good video.
GOOD VIDEO
Spray Blaster to the holding screws for 30 min and they will come loose. The two holes on the disk are used to screw in 10mm screws which will press out the disk. No more drilling or hammering the disk.😊
Use an impact driver to unscrew that bolts on the rotors easy
What should be the minimum thickness of old rotors to work on ?
Hi, How is that Riken snowtime tyre? I was womdering to get it for the old little swift, but I was unsure. Thanks for the video, I was watching to check where to put the jackstsands. 👌🏻
Smear a little brake or copper grease on threads of retaining screws then they should nt need drilling out.! Also for peace of mind i would locktite the carrier bolts as u need them to stay tight for safety. And really get a half inch drive socket set much easier and tightens properly.
What’s the part number for the rotors ?
Socket or ring spanner would stop you from rounding nuts 👍
@LukeModsxd
Жыл бұрын
Thank you! Won't forget the info next time!
What size are the disc screws? Cheers
@LukeModsxd
Жыл бұрын
If I remember correctly, they were M5x10 or shorter. Sorry that was a long time ago..
Price
Græse maby 🤔
Price{ disc and pad both}
@LukeModsxd
3 жыл бұрын
If I remember correctly, I paid for the Brembo discs and the Textar pads around €70. Only fronts.
A esos tornillos del caliper les falto apriete pues con esas llaves españolas no sirven para un buen apretón eso es con dado y maneral
Well, I will list you the mistakes you are making. if you want to get better read, pay attention and apply. mistake 1. we never use a spanner on these kinds of screws. we apply a nut And we work with a ratchet. Error 2. The small disc support screws are removed With a special tool, not as you show, this way is for non-owners. error 3. The Textar It always has the special reset support plates in the package, why didn't you use them?? Error 4. The bearing surface of the disc is cleaned and lubricated with copper paste.Error 5. The wheel bolts are tightened with a torque wrench to a specific torque. Suzuki Gives 8.3 nm.This from someone who is getting old.I suggest you start by buying some serious tools.....
@LukeModsxd
11 ай бұрын
Hey man thanks for the feedback. As you can see in the pinned comment I did another brake replacement video, that one was done the right way.