Hope you guys enjoyed! It would a HUGE HELP to the channel if you save this link as your amazon homepage, so when you shop the channel gets a small kickback: goo.gl/x1ehvA Please consider helping to keep these videos coming. *Parts List Below* : Parts list: 20PSI Propane Regulator - Here is the one I bought: amzn.to/2fsPgsn Here's a cheap numbered drill bit set. I used a #53 but you may need to adjust slightly for your specific setup: amzn.to/2PqoN16 1/4" Ball Valve: amzn.to/2UgOdTI 3/8" FL x 1/4 MIP union (to adapt regulator output to 1/4"): amzn.to/2UfaxNx 1/4" Coupling: amzn.to/2UrxBJa 1 1/4" to 3/4" Reducer: amzn.to/3qk3gIu 1" to 3/4" reducer: amzn.to/3xE3EDP 8" section of 3/4" threaded pipe: amzn.to/3d38Mtz 1/4" x 2" nipple: amzn.to/3iYHE2D 1/4" square head plug: amzn.to/3qguI9L Two 1/4" hose barbs: amzn.to/3xE3egJ 1/4" ID vinyl tubing (if you want to run your burner further away from your tank): amzn.to/3djxTZl

@_AZAZEL_

4 жыл бұрын

Jeff Bezos is smaug dont give him your business.

@troysimon9933

3 жыл бұрын

What modifications would be neccesary, in order to make this design into a "forced air" burner???

@manuelmendonca8482

3 жыл бұрын

@@troysimon9933 with this system you don't need forced air. My furnace melts , Aluminium , Brass , bronze, steel the whole furnace turns white inside. One more thing forced air erodes your crucibles faster.

@harrisoncrane360

2 жыл бұрын

Would it work to drill the nozzle with a 1/16 of an inch bit

This is the cleanest flame I've seen on burner videos. Great job.

I really appreciate the content, super informative. I'm new to forging/blacksmithing. I'm going to give this a try. The one thing I wish you would have clarified is the process of the propane end of the burner. I'm kinda lost on the configuration. Thanks again man.

I made this following your instructions but used a 1/2 cap, 1.5 inch to 1 inch reducer coupling, 1 inch pipe and a 1.5mm hole for the orifice with a 10 pound regulator and it worked very well! Thank you for your contributions to the DIY community! I was just about to give up on making my own burner after my old one with the same regulator failed to produce a blue flame. I think my problem was the amount of airflow in the old system that reused a burner from a furnace with a 1" coupling welded on. I still ordered the new regulator because I want to see how hot I can make it but overall a wild success! Thank you again!

My Grandpa taught me that the three holes in the drill chuck weren't there for convenience and that they were all three supposed to be used when tightening down on the drill bit. After that Drill bits didn't spin nearly as much. great video as always..

@d.faulkner8210

5 жыл бұрын

would not recomend using plastic tubing for a propane supply line,invest in a high pressure hose meant for propane,would be ugly if that plastic tubing melted from the heat while using that burner.nice burner design ,be safe..

@JustinTopp

5 жыл бұрын

I’ve heard that but it never had made a difference in my experience

@rufuscrackle

4 жыл бұрын

Heard that once in the 15 machine shops I worked at. Don't believe it and only that one guy out of a 100 did it.

@-yeme-

4 жыл бұрын

dont see it myself, all three tightening points are turning the exact same part in the chuck. could it make a difference where on that part you apply the turning force? idk. could be that just by taking the key out, putting it back in and tightening again youre making sure the tool is snug in the chuck, whether you use the same hole or a different one

@joeestes8114

4 жыл бұрын

Bugs Bunny thank you! I was going to comment the same thing!

I loved this video - Thanks for the info. I used your plan for making a forge burner but had to use a 30 psi propane regulator to make it work. I live at 8500 ft elevation so I assume thats why. Again thanks!

I guess this is a popular and much used design. I've seen dozens of videos through the years that are all almost identical starting with TKOR back in 2016. Great video with everything explained step by step, just like your other videos. As long as you keep making these cool build videos I'll keep watching and sharing.

@ElementalMaker

2 жыл бұрын

Thank you. Yes this is called a Reil burner. Very popular style coined after the man who designed them originally

This content is so good, been binge watching @ElementalMaker for the past week!

I built this in no time . Put a 30 lb. Reg on it . Works like a charm. Thanks ! This will go into a propane tank forge. Just a note ... doesn't seem to need but 10 lbs of pressure , at least for mine .

@adamgravelin3002

2 жыл бұрын

So I made this exact burner, and tried to use it in my propane tank forge but it just seems like it wants more air. Can't seem to figure out how to get it more air either.

I appreciate you, you were so straight forward even I can make one, off to the hardware store.

Well, I started my foundry build and of all the burner designs I looked at, yours is the one I went with. Fired it up and it works fantastic. Now I just need to finish building the foundry itself and I'm all good to go. Thanks

@ElementalMaker

4 жыл бұрын

Nice! Glad it was useful for you!

I built this exactly like he showed on the video. It works great! This bad boy puts out A LOT of heat!! Now I just need to make the forge to put it in. Thanks for the great video!

@ElementalMaker

6 жыл бұрын

Awesome! Glad its working great for you Daniel!

Loved the video! I have made several torches to pre-heat pipe before welding and I always just took an grease zerk and filed the end off, then removed the ball and spring.

@johngaudi8546

4 жыл бұрын

Do what? I can't picture which kind of grease fitting?

@tomt9543

4 жыл бұрын

John Gaudi A zerk is a standard grease fitting! Kind of like the proper name for the thing you inflate car tires through is a Schrader Valve! I love to call it a Schrader valve in general conversation because it gives the false impression that I know much about everything! Ha!

As a mathematician I can tell you that drilling your set screw holes 120 degrees apart would have allowed redirection of the flame down the center line of the burner very to be exceptionally simple.I admire your desire to always use the most efficient methodology for your diy build projects. I always enjoy watching a talented experimentalist in his element. You are like seeing Michael Faraday reborn; without him there would not have been an Edison or Einstein, or a Niagara power station humming with Nicolai Tesla's AC alternators..... Mr. Elemental for a while I thought that you might have been an alchemist like Isaac Newton, but there is no turning lead to gold, alas..... In the meantime carry on with the brilliant production of video material. Bye from Central Texas, USA.

@andrewroberts3187

2 жыл бұрын

That would work, but you would need a very long drill bit and have to line it up on both sides. The way he did it lowers the tolerances.

I’ve watched at least 15 of these on how to make a burner, and I think this one has been the most simplest and comprehensive covering all the unknowns. So after months of trying to decide on the right burner today I started buying the parts, though I AM curious why so many people use the welding tips drilled out yet this one works just fine with a quarter inch plug drilled out with a “60k bit” Which by the way seems to be about 2.65 mm. Hard to find locally but Amazon did have it for about eight dollars in tungsten. Thanks for making it sensible and doable. The flame seems to look right for the square forge I’ll soon weld up. I hope the lack of a Venturi doesn’t impair.

Very nice video Mate. Thanks for that. One of the Best Step by Step descriptions right here. The burner System is very good and Works like you said

Hey, great video!. I'm just wondering how hot this burner is able to get. Cheers.

I actually learned something thank you for the information most informative

I don't know why I waste so much time watching several videos made by several jokers before I end up watching yours. Someday I'll get smart and start at the finish. Your da man

@ElementalMaker

2 жыл бұрын

Thanks for the kind words Rikki

So, I didn't have an 8 inches pipe and I didn't have a #53 drill bit...I tried with a 10 inches and 1/16 orifice with a 0-30psi regulator...this is an inferno! I didn't even try full pressure haha. Thanks for the tutorial, I had an idea of a venturi burner, but it required much more work.

I've watched a bunch of these videos and I found that yours was easiest. Definitely be using your design for a double burner. - the galvanized tip. Im not very fond of getting poisoned

@tikitavi7120

3 жыл бұрын

Yep, that galvy has got to go.

@lx2077bob26

3 жыл бұрын

Just dip it in muratic acid and in seconds the coating is GONE

@Nubby007

2 жыл бұрын

@@lx2077bob26 or just leave it on vinegar overnight, lots cheaper

i ain't livin' yet bro... need that gold plated Allen wrench in my life

I am watching your video for the last time before I go to buy the parts. I am excited and your instruction is easy to follow and I can't wait for MY results....thanks again....Great stuff here

I just test fired my burner based on your design last night. Worked perfectly. Now I can start building my gas forge. I made two changes, however. First was to the end cap. I drilled and tapped it to take a mig tip. The other was to the squared coupler. I used the drill press to put four dinples in where the screws that hold the burner tip assembly can seat themselves. My thinking was that this way I don't have to over tighten in order to prevent the assembly from shifting. Regardless, greatly appreciate you taking the time to research and make a video on the subject. Stay safe. Cheers.

@beshkodiak

5 жыл бұрын

Axel Heinz i like that four dimple idea to hold the gas input. I have used a coal forge for 30 years but now that i live in the woods, propane is easier to get than coal so I am building a new propane forge.

@bunyanforgings7849

5 жыл бұрын

@@beshkodiak My new problem is setting up an efficient ventilation system. On my second test of the forge I set off the CO detector and then the wife (that was scarier). Hope to be using the forge soon. Good luck, Besh.

Hey man, just want to thank you for this video. I have never done anything like this before but I followed your instructions and...OH MY!!! My initial test was incredible. No need to change anything, working just like you said. Sounds like a hot air balloon and my neighbours are getting nervous. lol. THANKS MAN!!!

@ElementalMaker

5 жыл бұрын

Glad to hear it Tom 👍 stay safe and enjoy!

@conquerant8804

4 жыл бұрын

what size bit did you use

@wezerd

2 жыл бұрын

@@conquerant8804 30 thou

That's how we got metric and SAE sizes in our vehicles "I'll use metric since I have some lying around."

@therealjamespickering

3 жыл бұрын

Oh I know all about that. I used to have a Land Rover and it was anyone's guess what manner of bolt had been used.

I'm going to build mine just like this. No mig tip, no threaded damper, just wide open using a 1/16th jet orfice. Great work!

Thanks for making, this is the best and easiest design I could find. Definitely going to make this.

Nice video with the exception your internal flare needs to be black pipe and NOT galvanized. Zinc poisoning can kill you. The galvanized coupler on the back doesn't matter it's not directly exposed to the flame. I know you said you'd probably only use it outside but still, many who watch this wouldn't/don't know that. Stay safe everyone, and be informed.

@ElementalMaker

6 жыл бұрын

Very good point Jay. If KZread still would allow annotations I would make note of that in the video.

@AmericanPiddler

6 жыл бұрын

Jay Cee good sound advice! Care to check mine out? kzread.info/dash/bejne/pm2DzrSBcsvFhNo.html

@ytSaipan

6 жыл бұрын

The amount of zing on the flare will not kill you. As a precaution set it in a wood fire outside for about 20 minutes and the zinc will burn off.

@wonhuanglowsoverylow5000

6 жыл бұрын

Lmao. After the first burn the tiny quantity of zinc will burn off. The threat of zinc poisioning is insignificant compared to the fumes that will come from what is being melted or heated lol

@unmanaged

6 жыл бұрын

en.wikipedia.org/wiki/Metal_fume_fever#Treatment I would not be worried about such a small amount ....

How hot is this burner? You think it would be sufficient to power a gas forge on its own? (able to reach forge weld temps fairly quickly) A lot of guys use two burners, but I am wondering if it is necessary.

@AmericanPiddler

6 жыл бұрын

Jake Makes mine is hot enough for a forge check it out! kzread.info/dash/bejne/pm2DzrSBcsvFhNo.html

@ArizonaVaporTrails

6 жыл бұрын

You can check lp gas orifice charts on Google for btu and pressure. Run mine at 22psi and get 250000 btu

@AmericanPiddler

6 жыл бұрын

Jc Polston kzread.info/dash/bejne/pm2DzrSBcsvFhNo.html

@peterzingler6221

6 жыл бұрын

Actually these things work good i work AS a Metall builder\Knife maker in a little shop (2 men) and we got those propan torches Mount in diy furnaces made Form gas bootles ! Its more than enough for blacksmiting hardening and melting brass silber copper and so on

@justinpyle3415

6 жыл бұрын

in the correct envireonment, this temp flame can be used to get to welding temp, however the refractory materials and forge shape have to be pretty efficient. i suggest a dual set up of this, by using the 30psi regulator and adding a tee for a second burner, you wont need as long to get steel to welding temp with two, and it could pretty handily liquify the steel in an efficient forge/ foundry

Made one the other day, used a number 54 drill bit. With a 20psi regulator it rips. Flame is about 12" long and hot as hell. Thanks for the video and parts list, cheers 🍻

I’m curious about how much propane usage you get from this. I appreciate the tutorial and added an air regulator on the jet portion to be able to get a better control on the air flow through the reducer (just a piece of 16 g steel with the corners folded over and a hole drilled in the center with a small slot cut in it and a spiraled wire around the jet to twist open and closed for specific air flow control. But even without the air regulator, it burns through propane at an alarming rate. Would be interested in shooting around a few ideas with you.

What the diamètre you dril the square head plug please?

@TMRYZF

5 жыл бұрын

Thank you tributary House Ltd😉

Ah, yes, the German standard of holding force; guten tight

@ElementalMaker

5 жыл бұрын

My favorite standard as well!

@TrojanHorse1959

5 жыл бұрын

I thought that "gutentight" was German for "virgin?"...LOL!

@ChozoSR388

5 жыл бұрын

@@TrojanHorse1959 Ha!

@treygrubbs2550

5 жыл бұрын

What if your guten free? How tight do you get it then?

@Michel251167

4 жыл бұрын

it is not a German word..aim German..

Hey Elemental , do I need to put a round piece metal on the back end to control flame if its outside and windy ??

so use to seeing the other channels taking a thousand measurements to make sure its center glad to see im not the only one eyeballing things

Love the design (it should be noted that galvanization should not be anywhere near the fire).

@ElementalMaker

5 жыл бұрын

Thanks! And yes zinc and fire generally dont go together. In this case it's all the hardware store had, and it's such an insignificant amount you would need to be huffing it LOL

@lucienkpoikpo9288

5 жыл бұрын

GBEZE

@skeetfontenot4922

5 жыл бұрын

Just soak it in vinegar and then brush off the zinc.

Nice job. I would like to make one suggestion. Use a cordless drill to tap your holes. Generally speaking, people break less taps using a cordless than they do when tapping by hand.

@ElementalMaker

6 жыл бұрын

64t120r thanks for the tip! Oddly enough the only time I've ever broken taps was with a drill LOL. I'm bass akwards though, so that might be why.

@64t120r

6 жыл бұрын

Well . . . go break some. That is funny. I have to say, very good technique then. We get more broken taps when people do it by hand. Either way, I'll have to look through your videos and see what other goodies you have.

@NRDavis-wl8vn

6 жыл бұрын

Try tapping with your Drill Press. Drill hole, remove drill, insert tap. Everything is lined up. Turn and feed by hand or..... Get Tap Spinning, turn off power and feed down. Use to do it a lot in the machine shop for Quick and Dirty Jobs.

@ElementalMaker

6 жыл бұрын

David Dedrick some day I'll rack up the balls to do some power tapping on my drill press. I do it on my cnc mill, but I know there isn't any flex there, where as my drill press isn't super rigid, despite being "Rigid" brand.

@NRDavis-wl8vn

6 жыл бұрын

But.... Think of making a Video of trying the process. Scrap length of Aluminum and say a 1/4-20 tap. Not really necessary to keep everything locked down super tight. When you drilled out the Brass Plug you let it float a bit. In tapping that "float" is o.k. Just keep downward pressure and with no power you can stop the chuck by hand it you need to. Still have to back it out by hand but much faster than hand tapping both ways. In joy!

Thanks for the video. Very instructive. I do have a couple of questions if you don’t mind answering.1. How long will a 20# propane tank run using this burner?2. Is there any value in being able to control air flow too? Or enhance it?3. Is there some reference you would recommend to getting a deeper understanding on why this works as well as it appears to? Right now it all seems like a black art and would like to understand the science behind it.

I've watch multiple design for a forge burner, this is by far the best design. thank you for sharing.

@ElementalMaker

6 жыл бұрын

HYDROGENTEK I appreciate the kind words! Thanks for checking out my channel!

Minute 8:07 YEAH! SHAMELESS KY PLUG!! LOVEIT!

@ElementalMaker

6 жыл бұрын

Si Vis Pacem Para Bellum KY and plugs usually go together in another way butt I'm not quite sure how to break it to you.

@KendrasEdge757

6 жыл бұрын

ElementalMaker that’s cool, I’m not judging you, you’re into what you’re into. You don’t need to explain it to me!

Little bit of motor oil in a squirt can does wonders when drilling... The final build is bad-ass, though. Great work

@suzukiclaus3028

4 жыл бұрын

SparksFly vd40 ;)

@robertidenya1432

4 жыл бұрын

He did say a little KY jelly would do the trick 😊

@japudjuha

3 жыл бұрын

@@robertidenya1432 saving that for the spare nipple ;-)

@robertidenya1432

3 жыл бұрын

@@japudjuha hehehe

Best burner flame i have seen out of 10 KZread builds.. good work!

@ElementalMaker

4 жыл бұрын

Thanks!

@dooleyknoted5951

3 жыл бұрын

I concur! Plus, it's a better design than most commercial burgers available!

Great video and very straightforward. I just built mine and couldn't be happier

Very nice burner You have built here. However, you should not use the Teflon tape in the BLUE package, it is for liquid, like water. They make Teflon tape especially for gas pipe with a YELLOW outer ring. Be aware, be safe.

@joshavant4386

5 жыл бұрын

Thats not true at all. You can use blue ptfe tape for gas. No problems. If anything skip over the ptfe tape and use dope.

@sliderdrago8189

5 жыл бұрын

Colour usually determines thickness. Check approvals for your jurisdiction. But as Josh said. Use the dope man. I dont know anyone who uses tape for gas or oil.

@joshavant4386

5 жыл бұрын

@@sliderdrago8189 in my jurisdiction, once the pipe hits a certain size, you use both. I thinks it's after 1 1/2 inch.

@capt.craiglehrke4395

4 жыл бұрын

Seriously folks remember the build is an occasional use forge burner outside or in a shop. I wouldn't worry about what teflon tape to use unless I was hooking up a stove, furnace or water heater in the house.

@JonJon501

3 жыл бұрын

Don't need any of that.. its low pressure!

I have limited experience, but it looks to me that videos like this almost always show the burner burning beautifully in the open air. They rarely show how the burner performs in an enclosed furnace without additional air to support the flame. That is the question. Does the burner draw enough air for a strong and efficient flame in an enclosed furnace?

@DetailingJourney

2 жыл бұрын

It does

Very simple and easily attainable design. Saved me a bunch of time designing and scavenging the parts stores!

@ElementalMaker

6 жыл бұрын

Bs6.0pstroke_ 28 glad it was helpful for you! Thanks for checking out my channel!

Dude what a great video beat I've seen, your the man! I appreciate the knowledge. Thanks

Can use a MIG welder tip instead of drilling-out that tiny hole in that pipe-nipple cap.

@n.b.customtackle2017

6 жыл бұрын

Scott Fain yes

@yesdeere1376

6 жыл бұрын

What size, .025?

@Bspstroke_

6 жыл бұрын

YesDeere13 .060 would be the same as his. I'm sure .045 would work, you could use a torch tip file set to widen the hole.

I believe "Blueblock" for fitting joints as opposed to teflon tape.

@TheIrishdriven

3 жыл бұрын

Or the yellow tape

Excellent video, great project. Thanks so much, I will definitely do it.

@ElementalMaker

5 жыл бұрын

Glad you enjoyed Ruben 👍

Great video , What would happen if you added a little compressed air would you need a 20psi valve?

It cuts to commercial right when you're lighting it "And then he died"

It is a mistake to hold a object in your fingers/hand when drilling. I have seen so many accidents caused by holding with fingers/hand.

@JustinTopp

5 жыл бұрын

Lana yea I agree. I drilled into my finger by holding it in my hand too close. Had to get stitches wasn’t fun

@timothycasey6877

4 жыл бұрын

He also states never touch a spinning chuck.... Then proceeds to stop a spinning chuck by hand twice...

Now need to do a giant "garage heater" version! Would be awesome to see what you'd come up with

Great build, EASY to follow instructions! LOVE THE VID, love the humor! Always been interested in black/bladesmithing...just bought first anvil (Hay Budden) 160 pounder! Gotta start somewhere! Now the forge and burner! This vid is perfect, THANK YOU! Greetings from Salem, Oregon! Keep up the GREAT work! SUBBED! 👍👍

@ElementalMaker

4 жыл бұрын

Thank you!

@mystbourne3432

4 жыл бұрын

That’s a hell of a place to start. Good find.

5:17. Thank you for filing correctly.

That "cheap steel" is in fact ductile iron or malleable cast iron. You can tell by the chips when you are drilling it. Steel will spiral, even with a dull bit. Cast will give a granular chip just like the ones you got. Home Depot doesn't normally carry steel fittings as they cost more and few if any would ever know the difference. A better way to mount your burner gas jet might been to have used a 1 1/4" pipe plug with a hole drilled in the centre big enough for your gas jet to go through. Since the pipe plug has a 4 sided boss cast onto it you just drill and tap one hole to retain your gas nozzle. To get your air flow just drill 4 or 5 suitable holes through the plug around the boss. Much stronger and less likely to fall apart.

@marcandrei8061

6 жыл бұрын

Norman May no one cares smartass

@TheChoncho212

5 жыл бұрын

You can also tell it's cast be the mold marks on the side.

@willchoate7072

5 жыл бұрын

You do know steel can be cast, just because something has casting marks doesn't mean it's not steel. The chips or spirals is accurate.

Very cool. I just made one like yours but with a 5 psi regulator from a turkey fryer (I’ll get a bigger one, but I had it on hand) and it actually works well. The flame it puts out is about 2/3-3/4 what yours does. It should be enough for my small forge.

I have found that when drilling soft metals it is much better to grind the cutting surface of the bit to a - 5 to 10 degree angle as to the face you will avoid the catching or grabbing effect at the end of your drill as it punches through. What is happening is as you go through the end of your cut the face angle vs the cut angle are too inclined and the softer metals tend to let the drill dig in too quickly. If you reduce the angle of attack it will not tend to pull in as the surface begins to punch through the last portion of your cut therefore reducing the likelihood of your tool ceasing at the end of the punch. Good vid and thanks for filling me in on the foundry. keep it up.

"So many nipples, unbelievable" :D Great video mate. And not just because the nipples tho.

You say to not touch a "spinning chuck" but you touch it everytime to stop it!!!

@ElementalMaker

6 жыл бұрын

bob sunderland do way I say not what I do LOL

@seanogr8044

4 жыл бұрын

Do as I say not as I do 😆😆😆😆😆

@manuelmendonca8482

3 жыл бұрын

@@ElementalMaker Old hands or professional always touch the chuck we know what we are doing through years of experience and mistakes.

Just out of curiosity, do you happen to know what the btu of this burner build is and approximately how many lbs per hour does it use?

What is the minimum psi needed for you to run it at optimum power? I assume not more than 10?

For everyone worried about the galvanized coupler. IT'S BEHIND THE FLAME. therefore it's not burning

When drilling, tighten your chuck in two places or more... lessen the likelihood of the bit loosening.

@senatorjosephmccarthy2720

4 жыл бұрын

Yep, tighten all three.

@FPChris

4 жыл бұрын

And use cutting oil

I built this, and it works great, except I built a 2 burner system. I used a Mr heater high pressure regulator. It gives 20 PSI, and it's more than enough to run both burners. So I would assume the one you used would also be plenty for a 2 burner system.

Good show as always, thanks for sharing!

Why do you sound like AvE :D

Not bad. Unfortunately you cannot run this type of burner with forced induction. I used a tee and brought my propane into the side of the tee and used a .6mm mig tip for a nozzle. Super efficient and runs way longer on way less gas. No brass needed in my setup either. Everyone copies Majestic or Diamondback forges. Those need about 30 psi of propane to get up to forge welding temperature, mine achieves the same temp at 6 psi. I run mine at 3 psi for forging. Also...as stated, zinc will kill you. BBQ regulators have enough psi....but are low flow regulators and will not work. Get one from Suburban Propane or a Propane supply outfit.

@ElementalMaker

6 жыл бұрын

What are you using to provide the forced induction?

@jmbstudio6873

6 жыл бұрын

This little blower motor works great! www.zoro.com/dayton-blower-75-cfm-115v-045a-3016-rpm-1tdp3/i/G2510164/feature-product?KW2&gclid=EAIaIQobChMI18a3qIbQ1wIVlddkCh3AlwXwEAAYAyAAEgKU1_D_BwE&gclsrc=aw.ds

@jmbstudio6873

6 жыл бұрын

This is the burner I made. facebook.com/media/set/?set=a.1794002967556385.1073741831.1692028454420504&type=1&l=5fb7f4a34f

@jeffbobold

6 жыл бұрын

Studio 68 the FB link you posted isn't working for me. Do you have a video anywhere that shows your set up?

@6969smurfy

5 жыл бұрын

Studio 68 would have link to seen your burner, but I dont do that BS facebook ch!t no more....

hey! do you think theres a way to modify this design to make a forced air burner out of it? im using it just plain as is and the flame is burning super rich at times but other times it gets roaring along nicely. I know its not a regulator or gas jet issue (checked those a million times lol) and would like to try forced air without re building a brand new burner

Thanks to your video i made this single torch for my foundry and a 2 burner torch for my forge.

I thought for a second that I play AVE vid:D

@milos_radovanovic

4 жыл бұрын

I didn't believe it wasn't him until I tried pitch correction and couldn't get a perfect voice mach.

hehehehehehe he said "nipple" hehehehehehehe

@hypothalamusjellolap8177

4 жыл бұрын

It seems K Y gelly is the ticket.

Having some fun when showing laymen how to make a homemade torch makes it entertaining.. I learned from this, Thank you

@ElementalMaker

2 жыл бұрын

Thank you very much Francesco

Nice! Simple and functional

Watching you work is painful.

@atrumblood

6 жыл бұрын

We've been spoiled by watching AvE and This Old Tony. Lol

@WayneEarls

6 жыл бұрын

Machinist nightmare. but it worked.

@monkeyship74401

5 жыл бұрын

Probably painful for him too...

@rudawgs5418

5 жыл бұрын

Haha.....someone is gonna be miss digits soon...and NO I don't know how to make sandwiches...haha

I built one from the plans, works great, I have the stuff here to build a second one, hopefully I can get started on it soon!

Will be making this! Thanks for the video

@ElementalMaker

5 жыл бұрын

Your very welcome Terry! Good luck on your build!

Hey great video excellent work, I build it almost identical, it works but the flame is pretty yellow? Any tips to fix that? What size drill bit did you use for the 1/4 inch plug, maybe my hole size is to big? I tried drilling ant tapping for a mig tip but now it doesn’t work at all🤨

Just finished making a modified version of this. Instead of buying the regulator and other propane fittings, i bought a $35 basic weed burner and cut the flare off the end. Comes with a 10 foot hose, dial valve and squeeze control. Just file the edges and slightly enlarge the tip hole for better flow. Great video tho!

So does the flame end of the reducer have to be the size you have or can it be any size or is smaller better?

Awesome build, love it.

@ElementalMaker

4 жыл бұрын

Thanks Scott 👍

What size drill bit did you use for the brass plug and also what’s the reason for the reducer at the end?

Almost perfect! If you used a dye on the 2" nipple and extended the threads you could cut a piece of metal drill and tap it to fit those threads and then you will have an air control valve! Or get a nipple with longer threads .

COOL! thank you for sharing this. Now I had better get busy in build mine.

Wow, that was pretty simple, wish I would have watched this last night, could've saved me some cabbage. 🖖😎⚒

Would a brass coupling work as well as the galvanized coupling?

All I got was a yellow and blue flame and the 20 psi regulator is non adjustable... how far inset is the brass cap nozzle inside the reducer... propane tank is kinda low... I'm hoping that's all it is... the only thing I did different was put 1/8 plate over the 1 1/4 end with a center hole drilled for the nipple to slide through so I could center and tac weld it.... the plate has symmetrical holes drilled in it for oxygen flow... but yellow flame center blue and not a lot of pressure... I'd really like to get my forge going... any advice bud?

Good instructions, as a long time machinist I recommend Wiha Allen wrenches, but , Bondhus are a decent 2nd to them.

Great video I've watched a few videos now on this subject. They all have made it so complicated. Yours however right to the point and easy to follow. So thanks.

@ElementalMaker

5 жыл бұрын

Thanks Chris! Glad you found it informative!

So I just got the regulator and hooked everythin up and tried it out and it would not stay lit I’d put my lighter up to it and it roads but as soon as I take it away the flame goes out the only thing I did different is my pipes maybe 6” and maybe the hike in the plugs a bit bigger any suggestions on how to fix it?

@Kamal_AL-Hinai

5 жыл бұрын

Brandon Casey when this happens with me usually the wind is blowing. So might have to do something with the wind

What size drill bit did you use for the propane tip? In the brass pug?

That's what I needed to see. Thanks

Bonjour, merci pour le partage, je voulait commander sur le site toutes les pièces pour fabriquer le bruleur, mais il ne livre pas en France,

@smithy1578

4 жыл бұрын

Oui

Funny I came across your video as I am just abought to build a propane forge myself but out of a 20 gallon craftsman air compressor tank, do you have a video of how you ended up mounting the burner in your forge? . thanks for the informal video as I will be using this idea!

Today .. I make this ! I will let you know how it turns ! Semper Fi from Maine !

Woooohhh, de 5 videos que he visto éste es el que más me ha gustado, gracias, nada de flama amarilla

My flame doesn’t seem to be strong enough, and i don’t know why. I followed the instructions closely and have the 20psi regulator, but it doesn’t “roar” like the forges i’ve used at other places. Any thoughts?

Great video, thank you! When will you be building the forge? I built a coal forge last month and having fun with it but its messy smelly and take a large commitment of time to use, Im looking forward to seeing how you do it, I really like the burner design, do you think with a 30lb regulator and dual burners you could get to forge welding temps (2200F + - ) ? Thanks again for the informative video.

@joandar1

6 жыл бұрын

Matt, this may help, Cheers from John. Australia. en.wikipedia.org/wiki/Gas_burner