Thank you - worked perfectly, saved me a fortune.

@lauren-issimo2428

3 жыл бұрын

Hey how long did this hack last before needing to do it again

I stuck a folded up carrier bag & jammed it where the ripped seal is- The carrier bag completely maintained tight position throughout wash & held every single drop of water in!!! Quickest hack for night b3fore Xmas Eve anyway!!! :)

@praguecr4006

5 жыл бұрын

Way to go! I hope your solution lasts as long as you need it to!

Thanks for the tip! I am doing my third wash after repairing the gasket with Sugru and it is still dry.

I bought a hydroseat flange fixer for toilet install at lowes. It has a blue rubber gasket. Simply cut a smal piece of rubber off with scissors to cover the insidr opening where seal is missing and attach with electrical tape. Voila! No more leaks. I do keep a small piece of psper towel between the drum and washer door. Its been dry for months. Keep the flage on hand im case that piece needs to be replaced in the future but my repair has lasted 8 months. I dont overload the washer. This fix takes less than 5 min and most of that time was finding my scissors.

Still working? I bought a used LG washer and I was thinking that inside hoses are leaking, but later figured out it is a hole on the gasket which drips a lot of water in the floor from the bottom of the washer. Thank you for the video.

My tears have all been in the same spot. I'm on my third door seal 🤦‍♂️. I'll try this

@praguecr4006

2 жыл бұрын

Good luck! Tears (from the eye) and tears (of the gasket) have the same spelling in English… I hope you no longer have either!

Thank you, that stuff looks and acts like JB weld I use JB weld a lot but didn’t even cross my mind to use it for my seal Gonna try it out. Thanks again

I didn't understand What product did you use?

I worked in the repair business, a single strand of hair will cause a leak. If anything you should have kept all the glue on the inside and not on both sides, but glue will leak through unless patched.

Checking in to see how it hold / if there's any mold grown after a good 1.5 years..?

@praguecr4006

4 жыл бұрын

No mold!

Do not waiste youre money on Sugru. This will not hold for long and the rubber will be the same after 2-3 washes . Sugru will not hold unfortunatelly

Little bit confused. Looked like you did the same thing twice? Thanks.

@praguecr4006

4 жыл бұрын

This was my first ever project with Sugru - had I stopped messing with it around 4:15, I would have been done... just after that I say "oops" as I accidentally pull the pieces apart & then have to do the repair one more time (after which I say "I'm going to stop messing with it" - so that I don't pull it apart again!). Hope that helps. :)

Thanks for posting this. I have an almost identical tear in mine tonight, culprit was the metal end of a tape measure, and will give this product a go. I have a bosch front loader and don't think I have finger strength to replace the seal and trying to avoid the £80 plus call out fee plus parts.... See the part is 10-20gbp.

@praguecr4006

6 жыл бұрын

scaussie75 if I can do it, you can do it! Good luck!

@jeffzest8393

4 жыл бұрын

@@praguecr4006 Did not work for me, and I used a lot more than you. Perhaps I have a door problem too? But tear and leak both at 6:00.I wonder why the torn area and now "fixed" area is always at 6:00?

@praguecr4006

4 жыл бұрын

Probably gravity... as the drum spins the clothes can’t go up past around 10 o’clock, so they fall down to the 6 o’clock position - and once in a while I guess they pull the gasket away from the door.

@jeffzest8393

4 жыл бұрын

@@praguecr4006 Makes sense....and that is always where the tears occur. I am going to try again and see if leaks a second time. I have two packets left, and if still leaks may put on inside/back. But perhaps another problem? I did ask about this on a pay site called "Just Answers" I subscribe to and response by two techs was as follows: "Hi my name is Nathan and I am sorry to hear you are having an water leak on your washer, if the door seal is torn then the only solution is to replace the door seal. I am only telling you what I have found after many years of experience, glue might work for awhile but it is not the correct repair. If you want to take a chance of a damage floor because of a door seal then use the glue. You will not have to replace the door only the seal." and the other said: "The seals are specially made fro such appliances with proper fitting to prevent leaking. A glue will most certainly not prevent leaking and it doe not matter how strong it is. I have seen the product you mentioned and the problem will not be fixed by this product. You will have to buy a new pair of seals that will totally fix the problem. Other than that, you will only make a temporary solution with such glues and the problem will occur again." Hold long since your repair? Curious why you had leaks the first two times but not after that? Thanks. Cute child : )

@scaussie75

4 жыл бұрын

I second what the responders say. Sugru did not work for me. I could not replicate the exact thickness for the repair to seal and create the right suction. And i was pretty accurate. Sugru just didnt work to thinness required to replicate which is essential. It did stop some of the leak and was slower and I was ok with this. Stiff joints and lack of strength in hands stopped me replacing seal myself. I loved the product but not for washing machine seals.

Almost got away with it. But my landlord watched my video

thanks

Well, I used the product. Not as artfully as you, but the washer still dripped from the bottom of the glass. The seal had a couple tears similar to yours. Curious that you stated you still had leaks the first two loads. Any idea why? Maybe I did not put on right; however, I used several packets. I will have to examine later tonight (too hot to go in the garage right now!) Thanks!

@TheBigTimeBoiler

3 жыл бұрын

You ever get it fixed?

@jeffzest8393

3 жыл бұрын

@@TheBigTimeBoiler I bought a new washer. wanted $370 just for seal....if also door or other problems additional $$. I wonder if I put too much on, or just means product does not work or that problem was beyond seal.

@TheBigTimeBoiler

3 жыл бұрын

@@jeffzest8393 that's what I'm dealing with. Wondering if I am putting to much on. I'm actually moving and leaving behind washer with house at last minute. I've dealt with the little leaks for like a year but trying to make it nicer for new owners. I just bought a new seal tho but may have them deal with installation of it

@praguecr4006

3 жыл бұрын

@jeff no idea why I had leaks the first two times, but mine is a combination washer/dryer. It’s a condensing dryer (not forced air) - but I wonder if the little bit of heat plus vacuum was enough to correct any imperfections

Did you some more at the back or were you just using finger pressure? Thanks!

@praguecr4006

4 жыл бұрын

Finger pressure did a good job squeezing some material out the cracks. I added a bit in the back just to reinforce everything (but only because I had some Sugru left over)

👀 Ahoj, toto video je super, moc se mi líbí 👍 perfektní tvorba 👧🏻

@praguecr4006

6 жыл бұрын

Děkuji mnohokrát! 😃

Any ideas if a I have rip/tear on the bottom part not at the edge. More in the middle like a line tear. Any help is appreciated.

@praguecr4006

Жыл бұрын

Depending on how the tear “lays” - it may or may not leak - good luck!

do more vids

Will this work if the piece is missing altogether

@praguecr4006

4 жыл бұрын

Irene Henry depends on what you mean. Sugru can be molded to replace missing parts, but it will be a lot more complicated than what I showed in this video

@irenehenry4767

4 жыл бұрын

@@praguecr4006 worked great thanks very much

@epiphgd4302

Жыл бұрын

@@irenehenry4767 any luck with your fix?

What we can use in India what do we call this product

@praguecr4006

Жыл бұрын

Sugru calls itself “moldable glue”

Is this really works?

Did it work? Same thing happened to my new one😭😭

@praguecr4006

6 жыл бұрын

Yes! So far, so good...

I use uhu glue

@praguecr4006

6 жыл бұрын

Cool! I hadn’t heard of Uhu glue! I’ll try to find some and test them head-to-head :)

Is Sugru mould resistant, any signs of mould since this video was posted?

@praguecr4006

6 жыл бұрын

No signs of mold or mildew... As with any front load washer, remember to leave the door open to prevent things from growing...

@lingfromhongkong

6 жыл бұрын

Many thanks - I've just given this a go and waiting for the Sugru to set now!

@praguecr4006

6 жыл бұрын

I hope your project was as successful as mine!

@scorpionak841

6 жыл бұрын

Ling Li did it work?

@lingfromhongkong

6 жыл бұрын

yes, it worked a treat!

How did this hold up?

@praguecr4006

Жыл бұрын

Way beyond my expectations - still have not bought a new seal to replace the one I patched.

@eugeniolettere5414

9 ай бұрын

Do you still have the same washing machine?

@epiphgd4302

9 ай бұрын

@@eugeniolettere5414 done my own a while back. First time I did it didn’t hold though I’d be sure this was because I bought a split pack of sugru from eBay and it didn’t have the best before date on it/ didn’t cure properly. Second time I done it was 6 months ago using the proper bought from Amazon stuff and it’s held up perfectly. Let it cure for at least 2 days before using the machine. Longer if the machine is in a cold place and you’re applying it thick. Edit: the machine has been used at least 20 times a month for past 6 months on hot/ medium/ cold washes at high spin too. Highly recommend sugru!

Nice tutorial Bro's 👍✔😃 Regards from Europe from my channel

Keep your door closed

@praguecr4006

3 жыл бұрын

Agree - but that’s how you grow mold!

I'm more concerned that your son is biting the washing machine

@praguecr4006

6 жыл бұрын

Believe me - I was concerned too! Between Sugru & baby gates, we've been able to fix the situation :)

@isaacakhigbe5677

6 жыл бұрын

PragueCR 😂

@elle9633

3 жыл бұрын

Lols

Didn't work it was a lie.