hi everyone, today i show some useful tips for those vintage levers that are not quite the same as they were.
Жүктеу.....
Пікірлер: 44
@frankdevaney5156 Жыл бұрын
Patience of a saint. Well done, most enjoyable to watch.
@FrancoDX3 жыл бұрын
Thanks for this video. I enjoy working on old 3 Speeds so it’s always good to see what other people do to get old parts working again. Keep up the good work!
@retrobikestuff760
3 жыл бұрын
Thank you franco 👍
@LeeTanczos Жыл бұрын
brilliant ! always wondered how these worked since I was a kid lol
@The-Armed-Pacifist3 жыл бұрын
What a patient guy. Nice work.
@retrobikestuff760
3 жыл бұрын
Thank you 🙏
@nigelgrant4123 Жыл бұрын
Thanks very much. I'm just refurbishing my dad's 1962 Raleigh Superbe with a four-speed SA FG hub. I'm no expert, so everything's trial and error. I stripped the trigger, cleaned it, and reassembled using two 2BA brass screws and nuts rather than rivets. The bike will get very little use, so the screw shanks shouldn't wear a lot.
@greg1268
Жыл бұрын
I was thinking of doing the same thing! Using small nuts and bolts to hold it together. But maybe not. I just think it would be easier to clean. How has your been working out?
@nigelgrant4123
Жыл бұрын
@@greg1268 I think it's fine, but I've hardly used the bike. I think the screws will last many years.
@richardchiriboga4424 Жыл бұрын
Great video!! So very helpful!!!! Many thanks!!!!
@retrobikestuff760
Жыл бұрын
Your welcome
@peterjanczer8618 Жыл бұрын
I think when assembling the two pins it is important to put the back plate onto a hole and then to press or hammer them into their final position. However, thanks for the instruction!
@johnzehrbach8208 ай бұрын
as a kid, I had one on a stingray with banana seat.
@wilmaw6835 Жыл бұрын
Super to watch, thx a lot!
@retrobikestuff760
Жыл бұрын
Your welcome 👍
@shoeibkhan95642 жыл бұрын
Thank you sir For this shifter restore tips I am also happy
@retrobikestuff760
2 жыл бұрын
Your welcome buddy 👍
@mikehall78063 жыл бұрын
Great video, I just happen to be refurbishing 2 3 speed trigger shifters that I picked up from eBay
@retrobikestuff760
3 жыл бұрын
👍👍👍
@retrobikestuff760
3 жыл бұрын
Thank you 😊 and good luck with your refurb 👍
@antonioteixeira22162 жыл бұрын
Thankiu. Nice. 👍🚴
@Stephen-cd1id3 жыл бұрын
Great vid and knowledge, how did you flatten out the drill bit end pls also how does the new wire fit in :) you keep posting i will keep watching Steve NZ
@retrobikestuff760
3 жыл бұрын
Thanks Stephen for watching, the drill bit sits in place snug so just make sure you get the correct thickness or sand down to make fit, the gear cable are you referring too, if so that goes in at the back of the lever 👍
@johnjusko47892 жыл бұрын
hello mate are the sturmey archer 4 speed hubs still available today in this year of 2021?
@thomasroberts28693 жыл бұрын
Cool video! Do you lubricate the shifter at all?
@retrobikestuff760
3 жыл бұрын
Thank you, occasional thin oil will be fine mate 👍
@selvinjose19632 жыл бұрын
Nice effort 👍, Can I get few numbers of shifters for restoration of my 3&4 speed hubs.
@retrobikestuff760
2 жыл бұрын
Hi thanks What’s your question please ?
@selvinjose1963
2 жыл бұрын
@@retrobikestuff760 I want few numbers of shifters, can you give me .
@jameso26753 жыл бұрын
Hi, Great video. I need to service my 4 sp SA shifter as I suspect the clutch and spring need replacing, it does not hold gear 1. Where can I purchase a new clutch? Can I send this into you for a service?
@retrobikestuff760
3 жыл бұрын
Check eBay for parts although they are hard to find, I’m also after some bits 😂
@retrobikestuff760
3 жыл бұрын
Thanks also 👍
@zolinator3 жыл бұрын
What did you clean the plate it to make it go gold coloured? It's a nice touch.
@retrobikestuff760
3 жыл бұрын
If you use a fine wire wool it will take off the silver, maybe a bit of cutting paste too 👍
@retrobikestuff760
3 жыл бұрын
Thank you 😊
@rixretros3 жыл бұрын
Is there a reason you're not greasing everything up before reassembly ??
@retrobikestuff760
3 жыл бұрын
I’m demonstrating problem solving however lite oiling will suffice 👍
@nigelnightmare41603 жыл бұрын
Why couldn't you bend the spring to make it tighter?
@retrobikestuff760
3 жыл бұрын
You can try that, in the past the springs have snapped on me so I avoid it
@truckertom3323 Жыл бұрын
BLNH on the trigger what does that stand for?
@Apheresis
Жыл бұрын
B for Bottom gear (super low) L for regular Low gear- N for normal(direct drive} and H for High gear(overdrive). The sturmey archer story by Tony Hadland is good. Just in case you want to know almost everything. Except 4 speed trigger work.
Пікірлер: 44
Patience of a saint. Well done, most enjoyable to watch.
Thanks for this video. I enjoy working on old 3 Speeds so it’s always good to see what other people do to get old parts working again. Keep up the good work!
@retrobikestuff760
3 жыл бұрын
Thank you franco 👍
brilliant ! always wondered how these worked since I was a kid lol
What a patient guy. Nice work.
@retrobikestuff760
3 жыл бұрын
Thank you 🙏
Thanks very much. I'm just refurbishing my dad's 1962 Raleigh Superbe with a four-speed SA FG hub. I'm no expert, so everything's trial and error. I stripped the trigger, cleaned it, and reassembled using two 2BA brass screws and nuts rather than rivets. The bike will get very little use, so the screw shanks shouldn't wear a lot.
@greg1268
Жыл бұрын
I was thinking of doing the same thing! Using small nuts and bolts to hold it together. But maybe not. I just think it would be easier to clean. How has your been working out?
@nigelgrant4123
Жыл бұрын
@@greg1268 I think it's fine, but I've hardly used the bike. I think the screws will last many years.
Great video!! So very helpful!!!! Many thanks!!!!
@retrobikestuff760
Жыл бұрын
Your welcome
I think when assembling the two pins it is important to put the back plate onto a hole and then to press or hammer them into their final position. However, thanks for the instruction!
as a kid, I had one on a stingray with banana seat.
Super to watch, thx a lot!
@retrobikestuff760
Жыл бұрын
Your welcome 👍
Thank you sir For this shifter restore tips I am also happy
@retrobikestuff760
2 жыл бұрын
Your welcome buddy 👍
Great video, I just happen to be refurbishing 2 3 speed trigger shifters that I picked up from eBay
@retrobikestuff760
3 жыл бұрын
👍👍👍
@retrobikestuff760
3 жыл бұрын
Thank you 😊 and good luck with your refurb 👍
Thankiu. Nice. 👍🚴
Great vid and knowledge, how did you flatten out the drill bit end pls also how does the new wire fit in :) you keep posting i will keep watching Steve NZ
@retrobikestuff760
3 жыл бұрын
Thanks Stephen for watching, the drill bit sits in place snug so just make sure you get the correct thickness or sand down to make fit, the gear cable are you referring too, if so that goes in at the back of the lever 👍
hello mate are the sturmey archer 4 speed hubs still available today in this year of 2021?
Cool video! Do you lubricate the shifter at all?
@retrobikestuff760
3 жыл бұрын
Thank you, occasional thin oil will be fine mate 👍
Nice effort 👍, Can I get few numbers of shifters for restoration of my 3&4 speed hubs.
@retrobikestuff760
2 жыл бұрын
Hi thanks What’s your question please ?
@selvinjose1963
2 жыл бұрын
@@retrobikestuff760 I want few numbers of shifters, can you give me .
Hi, Great video. I need to service my 4 sp SA shifter as I suspect the clutch and spring need replacing, it does not hold gear 1. Where can I purchase a new clutch? Can I send this into you for a service?
@retrobikestuff760
3 жыл бұрын
Check eBay for parts although they are hard to find, I’m also after some bits 😂
@retrobikestuff760
3 жыл бұрын
Thanks also 👍
What did you clean the plate it to make it go gold coloured? It's a nice touch.
@retrobikestuff760
3 жыл бұрын
If you use a fine wire wool it will take off the silver, maybe a bit of cutting paste too 👍
@retrobikestuff760
3 жыл бұрын
Thank you 😊
Is there a reason you're not greasing everything up before reassembly ??
@retrobikestuff760
3 жыл бұрын
I’m demonstrating problem solving however lite oiling will suffice 👍
Why couldn't you bend the spring to make it tighter?
@retrobikestuff760
3 жыл бұрын
You can try that, in the past the springs have snapped on me so I avoid it
BLNH on the trigger what does that stand for?
@Apheresis
Жыл бұрын
B for Bottom gear (super low) L for regular Low gear- N for normal(direct drive} and H for High gear(overdrive). The sturmey archer story by Tony Hadland is good. Just in case you want to know almost everything. Except 4 speed trigger work.
@truckertom3323
Жыл бұрын
@@Apheresis ok thank you.
Try it on with cable
Itu harganya berapa Suwiterny pak