When I hear those three words "Hey there gang..." it just perks up my day, thanks!

I learned one thing today - tung oil isn’t made from tongues. I can sleep happily now

The wood that was replaced by washers didn't just disappear. The bump at the end of the neck is a result of that wood being displaced upwards.if you think about it, it's the path of least resistance. I've never seen this on a guitar before, but occasionally on older Fender basses, particularly ones that have had the end of the fingerboard planed thinner to counter the 'tongue rise' effect.

@OtherTheDave

4 жыл бұрын

Oh that’s an interesting idea!

@chuckyz2

4 жыл бұрын

It didn't show with the notched straight edge and he said the high frets didn't lift. It appears to be a bad setup from the factory or someone leveled the frets around the high one. A lot of people use short leveling sanders or attempt to do just problem areas and not level the board the frets with a sander that is full length. Combined with not using a notched straight edge first before leveling. When you use the nut on the truss to apply tension one way or the other, the ends of the fret board can dive or raise. I was surprised he didn't show us the results after leveling the high frets b4 he put it back together. Also, when leveling with strings off, then stringing it up and adjusting the truss can throw the leveling off ass the wood can bend unsymmetrically. Fenders are pretty good. Mahogany almost always has to be leveled under tension.

@HBSuccess

4 жыл бұрын

Brian Mascarin I think you’re 100% correct. It’s no coincidence the two high frets are directly over the compressed neck wood. Fender’s rosewood cap is not a whole lot thicker than a veneer, it’s not going to add any resistance and neither will two standard fret wires. Owner compounded the problem by continually cranking on the truss rod instead of leveling the frets.

@wrenchhead4378

4 жыл бұрын

Oh shit!!! Yer right!

@carpediem4413

4 жыл бұрын

@@HBSuccess No way..so My JM signature strat had what seemed to be a slight hump in in the heel area (originally had some buzz, and noticed it). I leveled with a fallaway and it seemed to help but still some slight buzzing. Added washers and tightened up that seemed to help for a day or so and relief is back... any suggestions? If it really is soft wood in the truss rod hole does that mean its gonna keep pushing up on the heel area of the fingerboard? , what to do?

Every guy watching this be thinkin' "bet i could get that washer out"

@joebodynobody764

4 жыл бұрын

Just need a bigger hammer.

@Scodiddly

4 жыл бұрын

Magnets.

@jwhite1016aol

4 жыл бұрын

@@Scodiddly thats one of my two thoughts on it as well

@onemanswrld

4 жыл бұрын

Dynamite......

@Monomonmamon

4 жыл бұрын

onemans world that could fix it and also add road worn heavily 👌🏼

What i really don’t understand is the negative feedback some leave here! You’re kind, funny and honest. You invest several hours to release these videos since we all know you could do your jobs much faster if you didn’t have to worry about the video camera etc. but, still, people will dislike it! Unbelievable! I hope that won’t stop you! Wish i could be your apprentice!

Damn those 15 minutes flew by

Nice work as always. I have come across this problem a few times. Last time, I concluded the nut had been replaced with one that didn't have enough thread length. A washer is not a machined bushing, it is punched out of flat stock, so it is rounded on one side and burred on the other. It will flex, and a stack of them will act like a spring. I like the idea of gluing in the the lowest one, but I would respectfully suggest either finding another nut with more thread length, or making one yourself by tapping and cross-cutting a stainless bushing. Another option would be to have a single solid spacer bushing turned by a machine shop. You just supply OD, ID and length, and often a little job like this they will do on the spot. It will take them minutes. If you have a mate with a lathe, it will probably only cost you a six-pack. As for random high frets, this is also not uncommon. I have worked in a guitar factory, and fret wire from different models can get mixed up. I'm not sure how it got past the set up room though! I really like your point about getting a false reading of relief from the high frets. This would be confusing for an inexperienced person setting up their own axe. Thanks for your videos.

Amazed each time i watch your videos. Thank you for the great information.

Fascinating insight and top notch attention to detail. Great work sir.

Love your videos - great knowledge transfer and your voice is very soothing in an over-excited world. Thank you!

That is top notch guitar tech work! The fret rocker is always your friend. Thank you so much for this video!!!

You make my days better. Lots of love from Alberta

I have learned quite a bit of valuable information from watching both your electric and acoustic videos. Now I feel more comfortable doing fret work on my guitars. Thanks so much!

Superb quality video and craftsmanship, well done!

I have always loved watching your videos you definitely know what your doin your channel is one of the best on youtube

Always enlightening and entertaining to watch a craftsman at work. Cheers from Macleay Island Queensland Australia

My exact issue with high frets solved! Thanks for doing what you do.

Guitars are guitars. Thanks, Ted. Always delightful/satisfying to watch your presentations, regardless of instrument.

A Fender signature MIA.. so much about quality control over there. Great job again, sir.

My John Mayer signature Strat had the exact same neck issue. Without a ton of washers, the neck couldn’t intonate or setup correctly!! Eventually I sold the neck and body - and put the rest of the pickups and hardware in a custom shop neck and body. MUUUUCH better. But no one should have to do that with a JM Strat.

twoodfrd it was the frets all the time but you fixed that thats what counts I enjoyed the video and saw final great results. Thanks for the nice video be blessed with love care and grace.

Your teaching skills are outstanding. Wood does compress. You can run out of thread travel at some point.. But it seems that the fix was the high frets on the end giving extra trouble. Thanks for sharing again.

Very creative and knowledgable fix.

Twoodfrd thanks for noticing my comment I meant every word and more. You fixed the Fender strat electric guitar it was the frets all the time and you fixed the truss rod washers nut or what ever.Thanks for the nice video be blessed with loving care and grace.

Personally I like to add .002" - .003" of "fall away" to the last 5 frets. I find it allows for a bit lower action for the "shredders". It was especially helpful in the 90's with the scalloped fret board craze.

@twoodfrd

4 жыл бұрын

I always build them that way.

Great insights into fret and fingerboard reliefs.

That is shocking for such an expensive guitar.

@valentino3191

3 жыл бұрын

It's nostalgic to use 1950's technology and get all the period-correct look/feel/design...You unfortunately get all the mechanical issues those vintage guitars tend to develop over time also. =[

@j.schaefer5622

3 жыл бұрын

I worked over 15 years as a repairman and have seen all kind of problems on Custom Shop Fender and Gibson Guitars…you wont believe what I saw.

@valentino3191

2 жыл бұрын

I believe you. At the risk of offending some people, I’ll say that vintage designs were good in their respective eras, but I prefer modern truss rods and modern manufacturing processes.

Thanks for this.. very useful. I have something similar happening with a Cabronita I have with a double truss rod. Thought I was imagining it for 2 years

Unpopular opinion: linseed oil smells incredible, as does high quality turpentine. (Painter here)

@wrenchhead4378

4 жыл бұрын

Flax seed oil works very well and also smells great

@Monomonmamon

4 жыл бұрын

I remember sniffing the linseed oil bottle after using it for the first time I used it on my fretboard

@zdcyclops1lickley190

4 жыл бұрын

@@Monomonmamon Raw linseed oil not boiled. Boiled hardens and is a finish. Raw linseed soaks in and slows water movement in the finger board. You put a few drops on, cover the whole board and wipe of the excess. Once a year. Lemon oil is too thin and evaporates.

@christianboddum8783

4 жыл бұрын

A little whiff of acetone is not so bad either XD !!

@patrickdolan.

3 жыл бұрын

Ever had it catch on fire?? Lol

Another master class in how its done right.

Awesome work, love your channel!!!!

After watching your videos I am pretty confident in my abilities to open a repair shop. 😁

@minder4u1

3 жыл бұрын

yeah and after 45 years of watching E,R type tv drama's, I am looking for my first patient, for open heart surgery

Hate, hate, hateeeeeee, those truss rods that are in the “wrong end” of the neck! What a pain in the ass! ...LOL... Great Vid! See you at Timmies #1 for a Lg Double Double, eh! :)

@PelleKuipers

4 жыл бұрын

First thought I had as well. There are so many far superior options now making this trussrod completely obsolete.

@danielsgrunge

4 жыл бұрын

Same, it's stupid. But the headstock looks soooo good with no cavity

@Bloodray19

4 жыл бұрын

I am actually building a mustang, i already finished the neck, and I intentionally put the truss rod down there. I really like it

@PelleKuipers

4 жыл бұрын

@@danielsgrunge Then use those wheels at the other end capped off with a piece of wood. That way you can have the best of both worlds.

@maffooo2040

3 жыл бұрын

I really prefer the screwdriver adjustment though, I really wish guitar makers would just drop the Allan key adjustment thing, and put a screwdriver adjustment at the headstock

How odd. Interesting bit of fault finding there and great video too, this is one to remember.

My favorite video making guy dude.

I seem to remember seeing a vid where JM says he does intentionally plane a bit of relief into the middle frets, but I'm not sure if that was done at the factory per his specs. Thanks for another awesome vid.

I learn a lot from your videos, funny thing is that most of the times that you upload a video comes to my hands a guitar with a similar problem and i already know what to do . In this case, a "bow" in the frets. Cheers from Chile

From this video found I had same issue on my Mayer Sig Strat.. and got some ideas: Measured how sunk truss nut was (2mm), cut a 2mm walnut plug out of the Fender truss hole plugs they sell (got all my washers out though). CA glued walnut plug into hole bottom, let dry, added more CA to edges of walnut plug (waxed threads first and avoided getting CA on them by using pipette). Essentially created a solid base for truss Rod nut to push against. I also did a fret level (w/fallaway on upper frets) because the upper fretboard had a slight hump. Also did a heat treatment on neck/fretboard to straighten neck. Left neck in a backbow press for a week or so. Everything’s great now but it took a lot of work to get right. I am guessing the wood under fretboard was pushing up on high frets. If you have a JM strat & get buzzing, probably this is the issue. Awesome guitar & worth all the hassle but what a PITA.

I've just set up a 2008 JM Strat for a friend, and I too had truss rod adjustment problems. To get the neck flat enough, I really had to tighten the nut as much as I dared. All the adjustment happened over just a few degrees of of turn. I must have had the neck off and on again about 10 times before I got the neck bow set up correctly, all the time hoping that the rod didn't snap. Given all the time this type of neck has been made for, you'd have thought Fender would have got it right by now.

I just subscribed to your channel. Let me tell you, your videos are very interesting and also calming to watch. Very cool!

With regard to linseed oil for necks. My stepfather was a cabinet maker/ joiner by trade, 60 odd years of it. A real tradesman. Beautiful work. He taught me about using linseed oil on necks. The trick is mix it 50/50 with mineral turpentine. Use VERY sparingly, and as you say, WIPE IT ALL OFF. If you do that it won't be a worry. All my guitars for the last 55 years, with rosewood fret boards, have had this treatment, once a year. My older guitars woodwork, is in perfect shape. Doesn't stink, and isn't sticky/tacky either.

Nice work Ted and not a solder/sodder in sight. Sad to say that Nigel is now in therapy. We hope he pulls through!

Having done loads of strats, the neck shrinks more than the heel. Same on some acoustics. The heel "bulge" shows up in many strats as they age. There is a lock washer that fits the strat, and can be bent flat with needle nose. I have also come across that same problem, where you can not tighten the truss rod enough. The flattened lock washers fit well and work fine.

I had the same exact issue with a 62 reissue Stratocaster and came to the same conclusion that the wood under the truss rot adjusting nut was soft. After I added the third washer, I sold the guitar.

Really Fender? A John Mayer Signature with those issues? What are we now, Gibson?

@Monomonmamon

4 жыл бұрын

Michael Marsh Even john's Black1 had issues lol the wiring was not soldered fender didn't took care of him + his deal with fender made him play only fender which I guess he hates since he loves using other brands 🤦🏻‍♂️

@taotuhao5969

4 жыл бұрын

@@Monomonmamon Are you talking about the Kinman harness that eliminate soldering? I had read that the solderless system was reliable. I guess not?

@Monomonmamon

4 жыл бұрын

@@taotuhao5969 I do not know alot about soldering, all I know is John Mayer said his Black1 was unsoldered when it was delivered from the fender directly lmao

@bee.normal

4 жыл бұрын

There's a bunch of "green" (soft) necks from Fender, mostly basses, mostly with the truss rod nut on the bottom (like this one) and mostly made in Mexico. Nothing new.

@Les537

4 жыл бұрын

I bought a new player's model strat over the winter, buttercream. The first 3 frets buzzed. I had to give a brand new guitar a resurface. It plays great now. The gibson SG i bought last year came with 2 dead on arrival tuners and a few other issues. They are both great guitars now, but I should learn to buy in stock flavors instead of ordering blind, because each is different.

Imagine the damage that could have been inflicted from a couple of high frets were someone less experienced been charged with handling this job! Those frets would probably have been ground down to almost nothing chasing the phantom neck bow, great catch!

Love this guitar. I'll have one someday!

I would have turned a spacer on the lathe equal length to the stack of washers and used that with one lock washer. It's crazy to stack that many lock washers together.

@chuckyz2

4 жыл бұрын

I doubt he reused the lock washers.

@twoodfrd

4 жыл бұрын

I did not reuse the lock washers.

@stratocaster1greg

4 жыл бұрын

Always nice to own a lathe or 2.

@tenlittleindians

4 жыл бұрын

@@stratocaster1greg I have 4 and 3 of them are cnc.

@HBSuccess

4 жыл бұрын

stratocaster1greg ....especially a metal cutting lathe where you can whip out truss rod slugs on demand lol. That’s Jerry Rosa territory.

Friday afternoon job from Fender.

@thestuffmikedoes2309

4 жыл бұрын

David Noble this made me lol

I made my own lemon oil by soaking shredded clementine and lemon rind in baby oil. It's pretty amazing how brand new it makes fretboards look after a couple of soaks and vigorous scrubs with a tooth brush until there is no more visible dirt coming off of the board onto the cloth, and it smells really nice. I have a little over 200ml of it left and it should last me years. The toothbrush method seems to work really well, wiped off after with a microfiber cloth.

Thanks I learned something. thanks again

Just discovered your channel, interesting problem with a mushy truss rod. The multi washer problem looks like it might be similar to a related albeit very different issue when shimming mountings on industrial machines. The rule is never more than 3 shims - or they will act like a spring. I think if you replaced most of the stack of washers with a solid spacer then the mushiness will go away. BTW - love your work! Excellent videos

@matimaui

Жыл бұрын

more than 3 washers would act like a spring? how so?

@andydavis3494

Жыл бұрын

@@matimaui se Rob Mods comments below

Or... if that rod does break some day, you might get a router and a piece of walnut and make a skunk stripe on that neck, then insert the new rod, like they do at the factory. Just a thought. I've never done that. The last neck that had a broken truss rod went into the garbage. Just got a new neck -- bolt on, of course. I'm enjoying these electric guitar repairs. They're fun. Great diagnosis of the issue, and a nice, clean repair. Informative and entertaining, as usual.

@OtherTheDave

4 жыл бұрын

I _think_ I saw them take the fret board off a neck to get at a broken truss rod once on the stew mac channel.

@twoodfrd

4 жыл бұрын

@@OtherTheDave It can be done, especially on a "slab board" like this. The curved veneer boards would be very tricky to get off and put back on.

@perihelion7798

4 жыл бұрын

@@OtherTheDave Yeah...I believe that was set-neck guitar, however. With a bolt-on neck it's possible to route out the channel, but I've never tried it. Maybe cheaper just to buy another neck.

@OtherTheDave

4 жыл бұрын

Perihelion77 I went looking for the video. If this is the one I was thinking of, it wasn’t a set neck, it was a neck-through... even better! 😁 kzread.info/dash/bejne/h6Ou3NunoZzOgMo.html I know these stewmac videos are at least half ads for stuff they sell, but some are just plain interesting. They did one about a ceramic guitar!

Conjunctival forceps!! LOL! (I love your tools...)

I agree with you on the lemon oil vs linseed oil.

I love .011, I set all my guitars to it. I like the feel but also in my not so broad experience the guitars seem to ring out acoustically better when the relief is above .010.

Very clever fix.

FWIW I use walnut oil on fretboards. Won’t get gummy like linseed and won’t attack inlay and binding glue like lemon oil. Ran across it totally by accident. I was out of everything else and my niece had some walnut oil her purse. Why I have no idea.. but she did so I tried it. Worked great so that’s my go to now. 😂. Still using the same jar she gave me 3-4 yrs ago.

another job well done.

rewatching.. "I even tried a vacuum cleaner" kills me. I love this video lol

Guirian fret file... you're old school. I like that

Great video - I have the exact same guitar and exact same symptoms - Great guitar but neck won't hold relief and upper frets buzzing. Did a fret level and added fallaway but eventually goes back to buzzing due to too much relief. Had 3 washers in there but removed two and now a single washer compressed into the truss hole wood. Can't get last washer out. Concerned and what should I do - did this fix last? Other options? Thanks for any advice. UPDATE: Got all washers out. Cut a Fender walnut truss hole plug to match depth of sunk nut (2mm) & wick glued side edge of plug with thin CA glue (avoiding the rod). Worked great. Doing this fix (and fretboard heat & lengthy flatten jig press treatment to reset wood memory + fret level) fixed my guitar neck. Took a lot of work and fiddling. Thanks for the video & inspiration to fix this issue.

Thanks very much for the tips and the opportunity to learn. Thumbs up to crush a troll.

I've heard the ski jump at the end from shims too.

@Riverdeepnwide

4 жыл бұрын

Yes I've seen that develop over time, especially when too much torque was applied on the screws in softer woods. If the shim is placed between the screws (at frets 20/21) that can be avoided. But really it's difficult to deform properly dried hard maple in a short distance like that.

I have had a local luthier work on my guitars, I had him do something called fall away. The last 5-6 frets are lower than the other frets, since I never play the highest notes on the fretboard.

Glad you fixed it. If I were to have to extract the washer, I would have put a very thin layer of superglue on the face of a small metal tube and stuck that to the washer. If that failed, I would drill two opposing pilot holes with the smallest drill bit I have, then screw two long thin screws into the washer to pull it out.

Good catch!

I have exact same guitar.. neck problem on mine. have heard of a few others online which have twisted or humped necks.... mine had terrible buzz on upper frets... so I did a fallaway... but the damn thing won’t hold the action stable... I flatten using truss adjust (very snug) & added washers.. won’t hold and action gets high after a few weeks. PITA... there must be a defect on these.. bad wood, etc. I think what’s happening is wood near nut is compressing and forcing up under rosewood at uppermost frets.

You can thin linseed oil down. You don't have to slather it on with a paint roller. Also, the smell is lovely.

...plus I love the smell of linseed oil. I use it on bare wood guitars and ukus and although it takes forever to cure all woods and even metals like it as a thin organic protective layer. I have made about a hundred different instruments, including shakuhachi and didgeridoos using linseed oil as a seasoning and protective substance. When bamboo, for instance, is rolled and heated over a propane stove linseed oil seeps into the heated wood, inside and out. Poor people love linseed oil. Linseed oil can be applied over and over over the years and will eventually even form a thin and flexible layer of goodness.

You should go to Lee Valley and pick-up their 4pcs picks kit... It will set you back about 20 clams (if memory serves me right) but comes in super handy in those cases where you need to grab something (or dig a doggone washer) at the bottom of a hole..

A lot of people do not understand a 1/4-20 nut and bolt at 1 (one) ft.lb. t. will put over 200 psi. on the washers. The glue will just brake. And I hate to troll a master like this guy.

I suspect the compression on that bottom washer may have caused the wood to act like a clamp onto the washer as the downward tension pulls in the surrounding wood to clamp the edge of the washer, 2 possible attack methods there would be to somehow score around the washer with a very fine blade but due to the access size and restrictions you risk a actual blade breaking and staying wedged in plus you would have to make the tool to do it, my chosen method however would be to drill and tap the washer and then use a machine screw to remove the washer, this way very large upward forces can be applied with little risk of causing damage, although the drilling is the risky part and its a weigh up to whether it is really a big issue if it cannot be removed. I am primarily an Electrical Engineer and its that engineering side of me that gets my interest in videos like this, nothing better than to see a professional take in what has become firewood and through skill and experience restore it to a full working guitar.

Diagnostic genius

I have a nice 78 Tokai, and the trust rod rattles on the open A string I used spring washers that won't come out, the big problem is that I used stainless steal washers that do not mix with the carbon steel truss rod over time it might rust. The rattle is still there.

I have gotten that high fret at the high end of the fret board when I use a two way rod to remove back bow.It happens a lot for me.

Three tone sunburst became two tone. I like a very yellow in the center.

I've seen them dress the last four or six Frets up by the body ... grinding lower to create more relief down there on the neck ... your thoughts ??? I know you didn't do it ... I saw you knocked down just the 2 high ones ... love your channel ... thanks ... Dave ...

I have exact same guitar and the neck is giving me fits. After checking with a notched straightedge, it appeared to have a hump near 12 fret. I leveled frets with a fallaway. Seemed slightly better. Still some string buzz, action a bit high. Added washers and retightened and it initially seemed better.... but pulled the guitar out after a couple days and it seems the relief is back...ugh what a PITA guitar. Wondering what to do now? Soft wood may be the issue in the truss rod pocket? Gonna recheck the neck. Wish someone made a spacer instead of adding a ton of washers. how to harden up soft wood that is compressing?

I would say you'd think by about the 4th washer you'd want to get it professionally repaired however it seems they did one better and sold it on reverb or to guitar center.

Now that’s a true luthier word... “Flumixed”. Def. Confusing, Hard to believe, just freakin strange... 😂

@TheQakman

4 жыл бұрын

Buddy Martin Thanks for the definition. That’s the first thing I was wondering. Lol

@goodun2974

4 жыл бұрын

I believe it's properly spelled as "flummoxed". Great word, I use it frequently. Especially as I age....

@budandbean1

4 жыл бұрын

good 'un I’m pretty sure you are correct... I’ve never been much of a spel’er....

@goodun2974

4 жыл бұрын

@@budandbean1 , perhaps I can spell flummox because it's so close to "lummox", a term for a big guy who's maybe not so bright.....like my 120 pound Anatolian Shepherd. I sometimes refer to him affectionately as "dunderhead" or "lummox" when we take walks together; upon meeting the dog for the first time right after we adopted him, my favorite veterinarian said " He is the perfect dog for your family, because hes just a big doofus". Isn't language fun?!

@budandbean1

4 жыл бұрын

@good 'un 👍🏼 Too funny...

My favorite line, “I even tried a vacuum cleaner”

On your previous strat video ... I thought , I wonder if Dan Erlickman can play like that ..., great ending to a learned a lot from that video. Your humour is quite good too. Where do you get the thin super glue ? Cheers Alberta Dave

Is it okay to use clear mineral oil for fretboard conditioning? I've been using it for a while and like it very much, it doesn't build up or anything. I just wanted to know if it's okay

@Les537

4 жыл бұрын

I've been using mineral oil on my 97 les paul forever and it has aged without issue over many cold, dry winters. I hit my rosewood boards about 3 times a year, mostly over winter. No cracking, shrinking, discolouring, decomposing or junk build up. No problems ever.

that reminds me to not pay TOP dollar for guitars. it.s just bullshit. Love your channel!

@r33sus8

3 жыл бұрын

yeah i dont think i would ever go to high in price unless it was from a luthier working on one guitar at a time, mass produced just spend enough to get some quality parts and set up your self.

@p0pr0ck3t

3 жыл бұрын

or if you're going to spend 2,000 usd on a guitar support a small company instead of these neolithic corporations who've forgotten quality control!

I was wondering of it was possibly not a factory bodge, but the fret level situation makes me pretty sure it's factory. Spring washers? I also hear there's quite a lot of 'green' wood in recent Fender guitars... They also got prosecuted in the EU for price rigging recently. Oh dear

Not sure why the two lock washers are included in that stack. They will be “mushy” until they get loaded to the point of flattening. Also, about gluing them to each other and to the side of the truss rod hole, before compressing. Have you considered using a small bushing / spacer instead of the washers? There are various sizes / combinations of ID, OD and length. Seem like a solid stainless steel cylinder would perform more consistently than a stack of machine bolt washers and lock washers.

In fact, it is perfectly normal for the nut thread to be short and the nut itself to be made of a harder material than the truss rod... The typical trouble with "classic" anchors, I never seen before with two-way-action truss rods.

I like the electric stuff, too

Could you have glued something to the stubborn washer to pull it out? Maybe two small metal dowels?

@trym2121

4 жыл бұрын

Possible but can you accurately glue two metals together without including the wood in such tiny and narrow hole?

I have an 89 Les Paul that has a lift in the fretboard where it meets the body, I'm afraid of what the fix might be but I gotta ask.

@twoodfrd

4 жыл бұрын

If there's enough fret height it's not too big a job to dress them down.

this is some high end stuff when you think about it

I suspect the original owner cranked that rod tighter till he heard a pop and stopped. Then they added washers till it became obvious a new neck was needed so they sold it to guitar center or on reverb.

Pain in the ass truss rod design.

Yay new vid

I made a joke to my wife immediately, who was sitting next to me while I watched; then you said, "Have fun with that sentence."

First hit the like button and then we go on wach video 😎🎸👍

The only thing l might have tried to get that last washer out might be a couple quick blasts with compressed air. I might have given it a few squirts of air to see if it might get behind the washer and float it out. An extra minute or two of effort, that probably wouldn't work. But itd keep me awake at night wondering...

This could have worked or made things worse if it didnt but I'd likely have tried it and hoped for the best lol. So I'm thinking you get two metal rods that have a flat flush surface on the end. Mix up some two part steel reinforced epoxy (JB weld) and put a little on the tip of each rod then push each rod into the washer on either side until it bonds/cures. Then pull gently on either side slowly working out the stubborn washer. BUT then you have to find a solution for the original issue and building up washers with ca glue to build a bond with the wood not only is a solution but it negates having to get the final stubborn washer out. So I can completely understand why Twoodfrd went with that approach. My idea would certainly be risky cause if it didnt work I imagine the whole fretboard would have to be removed. So again just an idea but I fully understand why such an approach wasnt taken.

For sure those split lock washers have no business adding vagueness to the adjustment! Granted I work in a machine shop but I’d have made a brass spacer of the right height vs a stack of washers. Of course with them all bonded together that should remove any movement in the stack