Ini video yg terbaik bro... Di sertakan dgn gambar rajah nya.. Mudah bagiku yg baeu belajar.. Trm ksh bro... Dr malaysia... Bikin lagi bro videonya... Sertakan gambar..

@creativechannelpro371

4 жыл бұрын

Thank you so much bro for your support yes bro my all videos has circuit diagram like this video😊😊😊😊😊thank you thank you

Nice sharing 👍 full watch

@creativechannelpro371

2 жыл бұрын

☺️

Santos São Paulo Brasil perfeito Very Very good fiz com 5200 e1943 muito agradecido ao amigo 👍👍👍

@creativechannelpro371

4 жыл бұрын

Thanks❤️

Super bro

@creativechannelpro371

5 жыл бұрын

Thank you so much 😃😃😃😃😃😃😃😃😃😃😃😃

Sir, Circuit ke bass is exelant sound Allso perfected

@creativechannelpro371

4 жыл бұрын

Thank you so so so much friend

Boht Acha amplifier. Tayar hota hai good

@creativechannelpro371

4 жыл бұрын

Thank you so so much Bhai ji

Super video.

@creativechannelpro371

5 жыл бұрын

Thank you so so much Friend

@creativechannelpro371

5 жыл бұрын

Friend I am your subscriber already thanks friend to visit my channel

@creativechannelpro371

3 жыл бұрын

Thanks bro

@creativechannelpro371

3 жыл бұрын

😅

Very very very very very very good bhai

@creativechannelpro371

4 жыл бұрын

Thank you Bhai AP ki support ka

Hello sir isme volume treble or bass kaise connection kare Pl's batao

Good 👍

@creativechannelpro371

5 жыл бұрын

Thank you so much friend😃😃😃😃😃😃😃😃😃

Wow nice

@creativechannelpro371

5 жыл бұрын

Thank you bro

👍

Very good.

@creativechannelpro371

5 жыл бұрын

Thank you very very much friend

@devairpereira6472

5 жыл бұрын

@@creativechannelpro371 my first amplifier, I go copy tomorrow.

@creativechannelpro371

5 жыл бұрын

Thank you so much friend keep it up

wow nc vedio sir..i like it..

@creativechannelpro371

5 жыл бұрын

Thank you very much friend😊😊😊😊

@justdreamsiu3631

5 жыл бұрын

how many amperes can i put in this mini amp.

@creativechannelpro371

5 жыл бұрын

12 volt 2-3amps good

@justdreamsiu3631

5 жыл бұрын

thank you sir..

@creativechannelpro371

5 жыл бұрын

Welcome friend😃😃

amigo y de cuantos watts es el amplificador, si me guio por las resistencias de entre 100 k y 150 k pienso se trata de un amplificador de 100 watts o 150 watts

How would i turn this into a single channel instead of 2 channel? Thank you for making these videos, they are extremely helpful.

@AstrosElectronicsLab

Жыл бұрын

Remove one pair of transistors B688/D718. I wouldn't use this as a "serious" amplifier.

How to connect volume treble bass this circuit Pl's you make a next video

@creativechannelpro371

5 жыл бұрын

Hello friend friend for trebble bass Have a very different which connect with amplifier Or if you control volume you need a six pin Potential meter

Good

@creativechannelpro371

5 жыл бұрын

Thank you so much 😃

Wenn das klingt so wie es aussieht möchte ich taub und blind sein!!! löten will gelernt sein.lg

@creativechannelpro371

5 жыл бұрын

OK friend😦😃😃 I try next time better Thanks friend for watch my vedio

@schatzi1955

5 жыл бұрын

und der lustige Lötkolben.

@slobodanvukajlovic3275

5 жыл бұрын

@@creativechannelpro371 #sehsj

Its to much destrotion sound. Not clean. But this is good for biginner. Tq for tutorial

@creativechannelpro371

4 жыл бұрын

Thanks friend❤️

May i ask if i use 12vdc battery 7A, what is wattage power output can produce...thanks for sharing....

@creativechannelpro371

3 жыл бұрын

Bro can not use 7A its too much trasistors can not handle .

@AstrosElectronicsLab

Жыл бұрын

The power output would be the same if it was 12V 7A, or 12V 2A. The amperage the battery can supply is just that, what it can supply, not what the circuit consumes.

@AstrosElectronicsLab

Жыл бұрын

@@creativechannelpro371 wrong. That's not what he asked.

Good Morning, Creative Channel PRO; Congratulations on the video. Very well explained. Please. How many watts is the output to the speakers for each channel? Awaiting. Thankful.

@creativechannelpro371

5 жыл бұрын

Thank you so so much Dear friend sorry friend Wattage is not confirmed I Think 10W - 15W each Channel

@AstrosElectronicsLab

Жыл бұрын

@@creativechannelpro371 doubtful. Assume a maximum voltage of 12V for the supply, and around 6V p-p at the output because of how inefficient this circuit is. If each speaker is 8 ohms, then we take half the peak-peak voltage, which is 3 ^ 2 / 8 = ~1W. This, would be probably closer to being correct.

Very nice . Bhai isme clear sound ata he kya ? Hame v banana hen .

@creativechannelpro371

5 жыл бұрын

Yes but if you use it on low voltage

@rkideatech8735

5 жыл бұрын

@@creativechannelpro371 low voltage means 5volts ?

by running the speakers in series wouldn't that reduce the ohm load on them by half

@creativechannelpro371

5 жыл бұрын

Thanks for your information friend

@AstrosElectronicsLab

Жыл бұрын

Well, no. The positive "rail" is on each positive speaker post making this the "common" rail (most normal single-ended amplifiers use the negative rail as the common). Therefor, the speakers maybe in series with themselves (albeit reverse polarity to each other), but to the circuit they're considered separate.

Sir ye sircuit maxmum 25 mint k bad out metic band ho hats hai Kia Waja hai? Plz

Bhai ye dono transistor check karna bhi sikhav. Malti meter se. Plz.

@creativechannelpro371

5 жыл бұрын

Thanks for your nice comment Friend if transister dead its giving a 001 resistance in all pin 1 and 2 short or pin 1 and 3 short. Or 2 and 3 short etc ☺☺☺☺☺

इसमें 12 0 12 को इस्तेमाल कैसे करें ??या फिर 24 करें या -12 ओर + 12 दोनो दें। या सिर्फ 12 volt।।

If you only need one speaker, is it just half the circuit?

@creativechannelpro371

5 жыл бұрын

Thanks for comment friend if you need 1 channel amplifier you can make only one side

Brother 150k ohm resistor how much watt

@creativechannelpro371

5 жыл бұрын

1/2 watt resisters

Its work but the sound is a little bit low

@creativechannelpro371

5 жыл бұрын

Thank you so so much friend for comment May some reason your amp sound is low Input supply less Speakers Resisters or capacitors values different

HI: HOLA I CAN MAKE IT WHIT ANOTHER COMPONENT BUT SAME VALURE? PUEDO HACERLO CON OTROS TRANSISTORES PERO USANDO LOS MISMOS TRANBSISTORES DE 1000 MF ?' INTENTO REPARAR UN HOME TEATER.. GRACIAS

@creativechannelpro371

5 жыл бұрын

Thanks for Comment friend Friend you can also use Another Transisters to make it but Only Amplifier Transistors working Perfect If you Want to Repair Your Home Theater You can Replace Their Transister to Any other Equivalents transisters

@alexisboadas925

5 жыл бұрын

@@creativechannelpro371 oh thanks for you answer.. now i found this components, sorry for my english XD. but i have one transistor from 1000 mfd of 16v, i can use that? whit out problem. or can use any voltage.. i like sure.

@creativechannelpro371

5 жыл бұрын

yes friend you can use any voltage

@alexisboadas925

5 жыл бұрын

@@creativechannelpro371 thanks, but i have only one transistor of 16v 1000mf :( its ok whith this? is my last question today XD

@creativechannelpro371

5 жыл бұрын

Friend you can ask any questions on any time Friend I dont understand your Question Because Transisters don't have a Value of 1000mf Transisters only Have a number on it we can find its Values on internet on Capacitor have a Value Like 1000uf 16volt 1000uf 25volt etc Please friend tell me About component

Brother could you tell me how much audio out put power

@creativechannelpro371

5 жыл бұрын

I think 15-20w each channel not confirmed friend sorry for that😃😃😃😃😃

@GMDinolsiand

4 жыл бұрын

I think 6w because it low energy

@creativechannelpro371

4 жыл бұрын

May be friend thanks

@AstrosElectronicsLab

Жыл бұрын

@@GMDinolsiand closer to 1W

mmmmm if i want to use whith a car stereo.. when i connect the remote wire (blue poweer on) and the power 12 volt (red) wire ??

@creativechannelpro371

4 жыл бұрын

Sorry for late reply friend I don't understand your question

@motoapasionados

4 жыл бұрын

​@@creativechannelpro371 EN ESPAÑOL.. SI QUIERO USAR UN APARATO DE ESTOS CON UN CAR STEREO DEBO TENER DOS LINEAS QUE RECIBAN UNA DE 12 VOLT Y UNA DE REM. PARA ENCENDIDO DESDE EL CAR AUDO DONDE Y COMO PONGO EL REM EN UN AMPLIFICADOR CASERO DE ESTOS A 12 VOLT..APARTE DE LOS 12 VOKLTIOS DE FUERZA.. IF I WANT TO USE AN APPLIANCE OF THESE WITH A CAR STEREO I MUST HAVE TWO LINES THAT RECEIVE ONE OF 12 VOLT POWER AND ONE OF REM. TO TURN ON FROM THE CAR AUDO WHERE AND HOW DO I PUT THE REM IN A HOME AMPLIFIER OF THESE AT 12 VOLT. PART OF THE 12 VOLTS OF FORCE ..

@creativechannelpro371

4 жыл бұрын

Friend this amp is not good for car better you buy don't waste your important time

@motoapasionados

4 жыл бұрын

@@creativechannelpro371 why?? the amp its 12 volts like a carstereo...

@AstrosElectronicsLab

Жыл бұрын

You'll destroy the car stereo and for not much gain.

Power of how many wattage

@creativechannelpro371

5 жыл бұрын

Not confirmed but I think 15-20w

@AstrosElectronicsLab

Жыл бұрын

Around a watt

make a clip stereo amplifier with 6 transistors or mosfet

@creativechannelpro371

5 жыл бұрын

Thanks for great idea friend

B688 or D718 ko jyada se jyada kitna volt par chala sakte he??? 40 0 40 par chalega????

@creativechannelpro371

4 жыл бұрын

Bhai ye 40_0_40 =80volts bhai ye boht zada ha use 12 v battery if you have or 12v adapter

@yatinparmar6122

4 жыл бұрын

12 0 12 volt me sound nahi nikal raha he bhai. Thanks for riplay bro.

@creativechannelpro371

4 жыл бұрын

Bhai circuit diagram recheck kro

Sir can I make 5watt 4ohm stereo speaker same with you invention

@creativechannelpro371

4 жыл бұрын

Speaker may burn not good

@AstrosElectronicsLab

Жыл бұрын

I would say the output would be closer to 1W of amplifier, so should be fine. However, there's DC voltage flowing through the voice coil of the speaker all the time being Class-A, therefor the speaker would burn out after time anyway. This is a very BAD implementation of an amplifier. Really should be an output transformer in place of each speaker driver.

I make this circuit but when i turned on there is always humming sound comes from speakers when i use the transformer but when i use smps supply the humming goes. But i want to use the transformer what i do...What was the reason what can i do now..

@creativechannelpro371

4 жыл бұрын

This because of high amps . Better if you use 5 volt and At least 1amp supply. Low amp better result please try. You can Use Voltage regulator to reduce transformer Amps . 7805 or 7809 . Thanks for comment

@manuyadav6696

4 жыл бұрын

@@creativechannelpro371 i am using 12v 3.2 amp transformer with 5408 bridge rectifier , 4700uf 25v capacitor... I have also try 2 amp transformer and .5 amp transormer , .5 transformer is useless. But in.5 amp transformer the humming sound is coming but that high

@creativechannelpro371

4 жыл бұрын

Yes see High amps high humming sound bro its better if you use low amp supply If you have normal USB charger just cut any USB cable and use Charger as power supply.

@manuyadav6696

4 жыл бұрын

@@creativechannelpro371 ook thanks ...but the problem is this if i use low amp transformer the bass is almost gone only low sound comes

@creativechannelpro371

4 жыл бұрын

Yes bro I know . This amplifier good for normal use only. I use this circuit at least 6 months with my PC . USB Power

what is the maximum watts of this simple amplifier?

@creativechannelpro371

4 жыл бұрын

15_20watt each channel bro

@AstrosElectronicsLab

Жыл бұрын

@@creativechannelpro371 approximately 1W, bro. Unless you actually measured it with an oscilloscope, don't assume.

Alternate for B688 please , i dont have that handy

@AstrosElectronicsLab

Жыл бұрын

Any power transistor with a Hfe of around 160, collector voltage in this low powered instance is irrelevant, but you'd want a collector current capability of around 5A should do. So, TIP-35C/TIP-36C, 2N3055/MJ2955 for example.

It gives humming soung. How to resolve?

@creativechannelpro371

5 жыл бұрын

Friend try it on 5volt

@AftabAlam-jz7jr

5 жыл бұрын

Phir bhi arahi hai .. mne 688 ki jgh 778 lagai hai

@creativechannelpro371

5 жыл бұрын

Bro its works well But I don't. Many friends say me its burn the speakers but bro its working fine when I make this please bro check yours resisters value

@creativechannelpro371

5 жыл бұрын

I think its give very low humming sound may I not noticed that Sorry for that my friend

Brother Is this amp more powerfull than before you showed the amplifier using d718

@creativechannelpro371

5 жыл бұрын

Yes brother more powerfull than previous vedio😃😃

Bro. when my amplifier playing sound is low and normal it is repeating.. why like this bro?

@creativechannelpro371

4 жыл бұрын

What sound repeating bro if you need help can WhatsApp +601169439048

@TheMediaPlus

4 жыл бұрын

Thank you bro

que voltaje es el capacitador

@creativechannelpro371

5 жыл бұрын

Any voltage capacitor

Cuantos watt de potencia?

@creativechannelpro371

5 жыл бұрын

Friend can you explain me in English language

@estebancayeita6508

5 жыл бұрын

@@creativechannelpro371 ???

@creativechannelpro371

5 жыл бұрын

I think friend at least 10w not confirm sorry for that friend

@creativechannelpro371

5 жыл бұрын

Welcome friend😃😃😃

capacitor volt

@creativechannelpro371

5 жыл бұрын

Thanks for comment friend any volt of capacitor work 1000uf

Suhu hot..

@creativechannelpro371

2 жыл бұрын

Mean

Gan kok suara pnya ku serak.... ap'y yg salh pdahal udh ak ikut'n smua

transistor pnp / npn ? pleace replay 🙏

@creativechannelpro371

4 жыл бұрын

sorry friend my Yt not show your comments late reply B688 pnp and D718 npn

amplificador de 100 watts por canal

this circuit gives approximately 14W, according to the analysis of the circuit in Multisim, but it is distorted when it has an input greater than 100mVp.

@creativechannelpro371

5 жыл бұрын

Friend thanks for your great information😃😃😃

@creativechannelpro371

5 жыл бұрын

Yes friend may be distorted but not feel to much

@AstrosElectronicsLab

Жыл бұрын

That's because it's not biased correctly. And, if I'm not mistaken, this is a Class-A amplifier; DC power shouldn't be running directly through the voice coils of the speakers.

BT 135 transistor amplyfaier kiss banaya please help me

@creativechannelpro371

5 жыл бұрын

Welcome friend but it not amp transister so plz tell me other all transisters you have i check for you Tell me plz

Hamre comment pe 500 likes do hum is ki photo reveal krein ge apne channel pe

How can this be a stereo amp when 2 spekers r in series? It mayaswell be 1 speaker with half the ohms 2, 8ohm spekers in series makes 4 ohms 1 channel at least make a 2 channel amp and not 1 bridged channel

@creativechannelpro371

5 жыл бұрын

Thanks friend for your information😃😊😊

@evbobdemon6994

5 жыл бұрын

@@creativechannelpro371 hello friend you are most welcome

@creativechannelpro371

5 жыл бұрын

Thanks😃

@AstrosElectronicsLab

Жыл бұрын

They're not in series. The positives of the speakers form the common rail. In this case, it's positive that's common, not negative. And, yes. I know the common rail on the input side is negative; it's just the positive is common to the speakers, not the amplifier.

im try this circuit at home my speker burn out

@creativechannelpro371

5 жыл бұрын

Oh no what happen

@creativechannelpro371

5 жыл бұрын

Friend how much input current

@creativechannelpro371

5 жыл бұрын

Speaker ohms

@creativechannelpro371

5 жыл бұрын

Friend very sad friend dead Sorry friend But friend I use this circuit but my speakers not burn Tell me about your circuit Input voltage Input amps Speakers ohms

@AstrosElectronicsLab

Жыл бұрын

That's because DC runs through the voice coil of the speaker all the time the amplifier is running. No speaker will last long with DC running through it.

How watt?

@AstrosElectronicsLab

Жыл бұрын

Around 1W my guess would be judging by its topology after I drew it out correctly on paper so I could see what was going on. It's a basic two-stage Class-A amplifier with very low efficiency and badly biased (distorted).

Voy jalab !voy jalab

@creativechannelpro371

4 жыл бұрын

Bro pls speak English

Can I use 12 volt car battery sir

@creativechannelpro371

5 жыл бұрын

Sir it depend on your battery amps I think 12 volt battery burn this

@jbaudiosmoga

5 жыл бұрын

I got success sir it's play on car battery, and I attached with treble bass circuit, now is very clear and loud voice

@jbaudiosmoga

5 жыл бұрын

I used 1941 and 5198 transistor in this circuit

@creativechannelpro371

5 жыл бұрын

Very nice sir👍👍

@basilemori8996

5 жыл бұрын

@@jbaudiosmoga hi pls can I have your Volume, Bass and Treble circuit and how you connected it to the Amp?

It work, but the sound is so bad and the speakers can burned. Basically it work because is the base. But needs a driver transistors and more resistens and capacitors. The sound is so bad and the problem of burn the speakers.

@creativechannelpro371

5 жыл бұрын

Thanks for your information friend you can use this amplifier on low volages no chance to burn speaker friend may be its your circuit problem or components is not working perfectly

@AstrosElectronicsLab

Жыл бұрын

@@creativechannelpro371 DC is going through the speaker at all times. Any speaker will be destroyed after time. An output transformer would solve that issue. This is Class-A, so the "150k" resistor should be chosen so that half the supply voltage appears between +V and where the negative speaker terminal is. This should clear up the distortion. You're probably looking at a resistor value closer to 1M.

Sir, main ne DVD ki suply ka circuit lgaya hai jes main 12v our 5v ko connect Kia hia Bluetooth k lay 5v our amplifier k lay fix 12v

@creativechannelpro371

4 жыл бұрын

Great

Would it be 1000uf 16v Capacitor?

@creativechannelpro371

4 жыл бұрын

Yes friend 1000 uf any voltage

@mehmetceliksu4562

4 жыл бұрын

@@creativechannelpro371 Thank you. I have a question. Can I connect 200w 4por 4 speakers? If I connect, do I connect in series or parallel?

@mehmetceliksu4562

4 жыл бұрын

@@creativechannelpro371 I'm sorry if I'm writing mistakes in the texts I use google vorticity from turkey

@creativechannelpro371

4 жыл бұрын

@@mehmetceliksu4562 thanks for comment friend yes work on all speakers no matter parallel or series

@mehmetceliksu4562

4 жыл бұрын

@@creativechannelpro371 Thank you very much, good evening my friend

Pcb

@creativechannelpro371

5 жыл бұрын

Friend I make this circuit without PCB

@AstrosElectronicsLab

Жыл бұрын

Why would you want a PCB for a junk implementation of an abomination this is supposedly supposed to be, called an "amplifier"?

Voleem botton logulator

@creativechannelpro371

5 жыл бұрын

Thanks for comment friend yes friend I not add volume controller because I don't have a 6 pin potential meter in stereo amplifier 6 pin potential meter is used

Audio ohms

@creativechannelpro371

5 жыл бұрын

Audio or speaker ohms

a cuatin only costs 2Us$

ខ្ញុំចង់មើលឱយបានច្រើននិងចង់ធ្វើតាម

I think it’s easier to build a computer lol

@creativechannelpro371

5 жыл бұрын

😄😄😄😆 Yes you are right

@engridkrasniqi36

5 жыл бұрын

Creative Channel PRO ok it’s easier to fucking buy it 🐒💯🥴

Rigestor 150k ohom wate kato

@creativechannelpro371

5 жыл бұрын

Any wattage work friend

Suena mas sucio y distorcionado

@creativechannelpro371

5 жыл бұрын

Thanks for Comment friend If you use 5volt supply no distortion come

Out power..?!!

@creativechannelpro371

4 жыл бұрын

sorry for late reply friend wattage not conform

@creativechannelpro371

4 жыл бұрын

15-20w may be

Bhai tera soldring iron bht bekaar hai new leele

@creativechannelpro371

5 жыл бұрын

Sahi kah rahay ho bhai ab menay new LA lia ha

Cara não tem grana para usar um ferro de solda bom.... Que merda em

سر سرکٹ تو بلکل اے ون ہے لیکن ایک مسلا آرہا ہے کہ سرکٹ جب گرم ہو جاتا ہے تو کام کرنا چھوڑ دیتا ہے اس کا کیا حل ہو گا

@creativechannelpro371

4 жыл бұрын

Supply ka current kam rakho

@sunnysunnylovely4234

4 жыл бұрын

Pani dal k thanda karlo

ខ្ញុំសូមអរគុណលោកច្រើនដែលបានបង្កើតកម្មវិធីនេះ

@creativechannelpro371

5 жыл бұрын

Friend plz explain me in english language

Severely distorted.

This is very weak

@creativechannelpro371

5 жыл бұрын

Sir I use this Amp I know its not to powerful but not very weak Thanks for comment

@mgh8286

5 жыл бұрын

@@creativechannelpro371 thank you. Can you introduce an electronic circuit that lets you set the fan according to the temperature?

@creativechannelpro371

5 жыл бұрын

OK friend thank you

Very bad design. You don't run DC thru the speakers! It's not even a real push-pull design. Instead the npn / pnp transistors is connected in a strange series / paralell configuration. A lot of these on KZread these days. If you love your speakers, don't build this crap. If you want to build an amplifier, get a decent schematic, or buy a kit on Ebay or elsewhere..

@creativechannelpro371

5 жыл бұрын

Thanks for your information friend Friend I also use this amplifier its not dangerous for speakers If you are using 4ohm speaker its dangerous Plz use 8ohm Speaker

@creativechannelpro371

5 жыл бұрын

Friend you Can use it on 5volt work 100% without problem

@BigTrouble324

5 жыл бұрын

It's probably not powerful enough to blow your speakers. Anyway, bad design. I can build a 300W amp for $50 on Ebay, instead on wasting money on something that is useless.

@creativechannelpro371

5 жыл бұрын

I know friend its better to to buy amp from eBay OK friend I try better next time thank you

@creativechannelpro371

5 жыл бұрын

OK friend Sorry for my Bad soldering and sorry for That if you not like this amplifier design