One of the most detailled instructions I have seen so far on building stairs! Thanks for uploading! Perhaps you can add a video on how all parts are finally assembled - if you would have that... Thanks a lot for this video!
@CMCraftsman Жыл бұрын
A trammel works great for marking your inside points to make sure you’re marking every point the same for both stringers.
@hoseinm92423 жыл бұрын
everything explained very clearly , very useful video . thank you so much
@carpentryjoinerywiganleigh9846
3 жыл бұрын
Glad it was helpful!
@zbigniewczaykowski51411 ай бұрын
There is a specific slightly dovetailed stair housing router cutter that should be used with that jig , not a straight cutter.
@scottwright388
8 ай бұрын
7°
@davidbarry7052 Жыл бұрын
This method is great.
@Sirjohnwilliamuk3 жыл бұрын
After watching thid video will definetelly use the 4 inch screw method instead. kkk Craftermanship excellent, time to build 5 months kkk
@TheToolnut
Жыл бұрын
🙄🥱
@georgeglz Жыл бұрын
What angle did you use for the template when marking out the stringer?
@carpentryjoinerywiganleigh9846
Жыл бұрын
UK building regs part K states stairs to be 42 degrees. The overall rise and overall going is divided by how many treads and risers wanted (within building regs max/ min amount) and pitch template made.
@georgeglz
Жыл бұрын
@@carpentryjoinerywiganleigh9846 Cheers, I'm making a set of 3 stairs for my school project.
@thedentons50
4 ай бұрын
Great video I’m a site joiner but need to make one … do I use a frame square and mark my 220 tread by my 186mm rise to get the marking the margin template
@hermenegildorodriguez68763 жыл бұрын
el espiche debería sobrepasar toda la espiga y morder o atravesar el pie¡¡
Пікірлер: 16
One of the most detailled instructions I have seen so far on building stairs! Thanks for uploading! Perhaps you can add a video on how all parts are finally assembled - if you would have that... Thanks a lot for this video!
A trammel works great for marking your inside points to make sure you’re marking every point the same for both stringers.
everything explained very clearly , very useful video . thank you so much
@carpentryjoinerywiganleigh9846
3 жыл бұрын
Glad it was helpful!
There is a specific slightly dovetailed stair housing router cutter that should be used with that jig , not a straight cutter.
@scottwright388
8 ай бұрын
7°
This method is great.
After watching thid video will definetelly use the 4 inch screw method instead. kkk Craftermanship excellent, time to build 5 months kkk
@TheToolnut
Жыл бұрын
🙄🥱
What angle did you use for the template when marking out the stringer?
@carpentryjoinerywiganleigh9846
Жыл бұрын
UK building regs part K states stairs to be 42 degrees. The overall rise and overall going is divided by how many treads and risers wanted (within building regs max/ min amount) and pitch template made.
@georgeglz
Жыл бұрын
@@carpentryjoinerywiganleigh9846 Cheers, I'm making a set of 3 stairs for my school project.
@thedentons50
4 ай бұрын
Great video I’m a site joiner but need to make one … do I use a frame square and mark my 220 tread by my 186mm rise to get the marking the margin template
el espiche debería sobrepasar toda la espiga y morder o atravesar el pie¡¡
bastante chapucero
No