SprayMax 2K on Outboard Cowling over Yamaha Paint - Awesome Results!
In this video I cover how to restore your outboard cowling with Spray can paint. The key is the SprayMax 2k clear coat. I cover the complete steps including stripping the old decals off (that had been painted over). Links to the products I used are listed below.
The SprayMax 2k clear coat is a great product to get a successful restoration with a smooth High GLoss finish. I've found that this clear coat not only goes well over the Yamaha yamalube paint I used here but will also do well on Moeller, Duplicolor and Rustoleum paints. It seems that it will cover just about any single stage enamel paint with the proper preparation.
If you're interested in the decal company I used, you can visit them at www.outboardgraphics.com. They do excellent work at an extremely reasonable price and I am super pleased at the decals they made for me.
Affiliate Links to Products and Tools used in this Video:
3M Eraser Wheel amzn.to/2Vzf12a
Alternative Eraser Wheel amzn.to/2U2n5bD
DupliColor Primer amzn.to/3hGx0w8
Yamaha 08D Paint amzn.to/3wPmqYp
SprayMax 2K Gloss amzn.to/3i6WG4o
Felt Squeegee amzn.to/36xi7WS
Link to Outboard Graphics Supplier I used in this video:
outboardgraphics.com/
00:00 Introduction
01:00 Removing Decals
01:40 Wet Sanding with 220 Grit
02:00 Items used in Restoration
02:56 Filling in Gouges with Fairing Compound
03:47 Sanding the Fairing Compound
04:10 Masking off the Seal
05:10 Applying Filler Primer
05:36 Wet Sanding Primer with 600 Grit
06:37 Applying Yamalube Color Paint (2 Coats)
08:22 Applying Spray Max 2K Gloss Clear Coat (3 Coats)
10:19 Applying Decals
#cowlingpaint
#outboardpaint
#CowlingRestoration
Пікірлер: 86
One of the most useful videos with timing to apply various coats😀
@ExtremeDIYGuy
3 ай бұрын
Glad you think so! Thanks for the kinds words!
Once again an excellent video. Nice job. It inspires me. I have a 2002 25 hp Yamaha 4 stroke that is faded badly from the sun because a teenager owned the boat before I bought it. I'm definitely going to sand and paint and decal it now.
@ExtremeDIYGuy
Жыл бұрын
Right on, go for it!
Thanks so much for sharing! I am going to do it exactly as you said. Cheers all the best
@ExtremeDIYGuy
Жыл бұрын
Best of luck!
Nice job man. Looks amazing
@ExtremeDIYGuy
3 жыл бұрын
Thank you! Cheers!
Super video on how to get a superb result with cans including all the safety you need plus as is obvious preparation and planning gives the best results. I imagine this could applied to other parts on a boat and would work well for Motorcycle Fairings or Side panels etc. Preparation is key..
@ExtremeDIYGuy
2 жыл бұрын
Glad you enjoyed it!
Man! Came out great.
@ExtremeDIYGuy
3 жыл бұрын
Thanks Zack!
Awesome job 👏
@ExtremeDIYGuy
Жыл бұрын
Thank you! Cheers!
Very helpful video!!
@ExtremeDIYGuy
3 ай бұрын
Glad it was helpful!
Great video!!
@ExtremeDIYGuy
Жыл бұрын
Thanks!
Great video
@ExtremeDIYGuy
Жыл бұрын
Thanks!
I got more out of this cowling paint video than the two main others. You explained everything perfectly and didn't over sand, paint, etc. I've read about it there jobs getting the orange peel on the clear coat - it appears the 2k you use and over lap tech keep that to a minimum...Thanks!
@ExtremeDIYGuy
2 жыл бұрын
Glad it was helpful!
Nice work!
@ExtremeDIYGuy
8 ай бұрын
Thanks!
@timrainger8908
8 ай бұрын
Would clear coating over the stickers help in the longterm?
I know it’s an older video but just wanted to say thank you!! Just finished mine and followed all of your directions. Came out pretty! Just wish the yamalube paint had a wider spray pattern. Not matter what I did I couldn’t make the lines totally disappear. Even after 3 coats of paint. Thanks again!!
@ExtremeDIYGuy
7 ай бұрын
Glad I could help!
@williamperry1462
7 ай бұрын
@@ExtremeDIYGuy update: turns out they sent me one can of 4d in place of all 8d!!! No wonder I couldn’t get rid of the lines!! Ugh. Sand and redo…. Always check the cans! Ugh they looked identical.
Nice job
@chrismendez696
Жыл бұрын
Where can we get the decals thx in avance didn’t see link
@ExtremeDIYGuy
Жыл бұрын
outboardgraphics.com/
Excellent. What grit block did you use to sand the fairing compound?
looks great! good job
@ExtremeDIYGuy
2 жыл бұрын
Thanks!
I used the 3 m wheel on my Yamaha 115 2 stroke decal it works great
@ExtremeDIYGuy
5 ай бұрын
Glad it worked for you!
Are there any issues using 2K which is an acrylic with the Yamalube enamel based paint?
I just purchased a BW. 1985 S.S. 15. The 70 horse cowling and lower unit need tlc. Having watched this video I’m going to redo the cowling,but have you ever repainted the lower unit?
Thanks
@ExtremeDIYGuy
5 ай бұрын
No problem
Great video man! What is that squeegee called that you used to press the water out from under the sticker and where did you get it? Also, what is the mix ratio for the soapy water? Thanks.
@ExtremeDIYGuy
Жыл бұрын
The squeegee came with the stickers. No set ratio, just a light squeeze and fill up with water!
I needed 2 cans of colorcoat to get the same result. Why that is i dont know
Any tips for painting the aluminum lower part of a yamaha? I have a small bit of corrosion bubbling underneath the paint on the seams
@ExtremeDIYGuy
Жыл бұрын
Use a similar technique as you would on the cowling, but I would fix the corrosion first.
thanks for posting. question, i am in the process of refinishing my yam f150. I am getting dust from over spray landing on the top painted surface. i am thinking need to wet sand that before additional coat. How did you deal with that?
@ExtremeDIYGuy
8 ай бұрын
First I would figure out why you are getting overspray, I didn't have to deal with that. But if you have overspray, you will have to sand it down between coats, I would go with the finest grit possible that will do the job without damaging the underlying coat.
goog job
@ExtremeDIYGuy
2 жыл бұрын
Thanks!
I let my base color dry for 3 days. Would I need to wet sand before applying the 2k clear since I waited so long?
@ExtremeDIYGuy
Жыл бұрын
Sticky question, If it were me, I would put another coat of the base color on after a light sanding and then put the 2k on over that. I'm pretty sure if you put 2k on over cured paint that it will craze.
Followed your video with my 90 2 stroke yam and after sanding and wiping it down I went to the primer and the cowling won't take paint in 4 or 5 spots. Any ideas? Its sanded down to the fiberglass in those spots too and the paint just dissipates after spraying and its white behind it.
@ExtremeDIYGuy
3 ай бұрын
I would try a different primer. Perhaps a specialty primer that is made for or compatible with fiberglass.
Gday mate i have to do this to my cowling i just checked out the price on amazon au 107.00 for the 3m wheel im gonna try the heat gun and if it dont work ill chew em off .
@ExtremeDIYGuy
2 жыл бұрын
Save your teeth! Amazon has quite a few knockoff wheels for a lot less!
Awesome video. Did you do any other wet sanding of the Yamaha paint or clear coat that wasn’t filmed?
@ExtremeDIYGuy
Жыл бұрын
That would be cheating lol. So nope, All the work is covered in the video.
@crewmax4240
Жыл бұрын
You're an artiste, man.
@Army4Runner
Жыл бұрын
@@ExtremeDIYGuyI’m going to try your method on my outboards. Wish me luck!
How did you match up the decals to the original placement?
@ExtremeDIYGuy
Жыл бұрын
I eyeballed it and took pictures of the original to guide me
Did you have much orange peel texture in the clear?
@ExtremeDIYGuy
2 жыл бұрын
Nope, perfectly smooth.
What’s the difference between the 04D and 08D paint because I have the 04D paint and I’m not sure if I should use it. I have the same engine as you.
@ExtremeDIYGuy
Жыл бұрын
I'll be honest, that confused me as well and I honestly cant remember which was for what. I would try 04d on a test piece and see if it works. I think they are similar enough in appearance that no one would really be able to tell the difference.
@kurtmead2066
11 ай бұрын
To figure out what color your motor is, look at the part number for a part like the bottom cowling. It will end in 4D or 8D for the correct color.
What do you think about using spraymax 2k over total boat wet edge to paint the hull on a 13 whaler?
@ExtremeDIYGuy
Жыл бұрын
I wouldn't It will probably dissolve the wetedge. I would just use a two part poly like Interlux perfection instead
@ChristianJohnsons
Жыл бұрын
@@ExtremeDIYGuy awesome thanks. Couple more questions. What brush do you recommend for roll and tip? Also how much paint is really needed to do bottom side of a whaler? 1 quart? 1 gallon? Trying to get all my supplies together. Your videos are awesome btw! I’ll be rewatching them again and again as I go.
@ExtremeDIYGuy
Жыл бұрын
Badger hair brush if you can get it, Jamestown distributers have a good selection. If your rolling Interlux perfection, you can thin it to 12-15% and roll it with a foam roller without tipping, it will settle into a nice glossy finish,
Do you have a link available for those decals?
@ExtremeDIYGuy
4 ай бұрын
outboardgraphics.com/#
Im re painting my Yamaha 50 Four stroke now . Where’s the best place to get decals . Yamaha dealership wants like $175
@ExtremeDIYGuy
Жыл бұрын
kzread.info?event=video_description&redir_token=QUFFLUhqbFlnbzF1T2VKYXRIM3M3ZkpFZFhtcHdRMVIxd3xBQ3Jtc0ttbTlwcWczUERUbnBqU3BfQTdBYUNZcEN2SzBWeUtSLVhnZk95YVQ2UHZrMEw4SllzblQ1SnZfVEtSVHNEdXhJSF9kNVNKbFVLQ2JwMGt3Z0k4aGo3MEpONEFicDdGUjF3b3R2WUtoYmp5Znk3eFUzcw&q=https%3A%2F%2Foutboardgraphics.com%2F&v=3ACBs4FGJ1A&html_redirect=1
You mentioned a link to the UK decal manufacturer. Is that available?
@ExtremeDIYGuy
2 жыл бұрын
Hi, yes, I just updated the description and added the link there, outboardgraphics.com/
@kirthall269
2 жыл бұрын
@@ExtremeDIYGuy Thanks, got it. Thanks for the video, it was exactly what I was looking for. I followed your steps on my Yamaha 150 and it came out better than I expected. Thanks again.
@ExtremeDIYGuy
2 жыл бұрын
@@kirthall269 Thank you I'm glad it was helpful to you!
What do you think of putting clear over the decals?
@ExtremeDIYGuy
2 жыл бұрын
I thought about it but the folks that make the decals advised against it.
@bobbell5928
2 жыл бұрын
@@ExtremeDIYGuy Glad I asked. Thanks
No sanding after base coat?
@ExtremeDIYGuy
Жыл бұрын
Only after the primer
Wow that's amazing work! Can you repaint my 90 Yamaha? 😊
@ExtremeDIYGuy
11 ай бұрын
I'm afraid not, sorry!