This really is testament to how amazingly designed Lego is. I wonder but I can't help but think that you were likely getting quite close to the physical limits of the material in those last few tests

@nathandamgaard3227

2 жыл бұрын

he definitely is. In one of the tests, when he stops it the gear spins the other way a little. That's from the axles twisting up under load, so when the load is removed they act like a spring and spin the gear the other direction

@lucyhartmann2082

2 жыл бұрын

Some time ago I watched a video, by Brick Experiment Channel I think. He used a steel axle for heavier workload

@jacobleeson4763

2 жыл бұрын

@@lucyhartmann2082 steel axle isn’t enough. The axle will just strip the gear and spin without the gear spinning. Need steel gear as well

@siggihero1

2 жыл бұрын

Im really impressed as well, but one of the problems i see. The tesla turbine was far too efficient because no material would hold together at Such high speeds. So i Wonder if he Will be able to break the sound barrier. Pls letme know what you guys think

@fireboat9063

2 жыл бұрын

If he spins it fast enough while spreading all the torque possible, it may be possible to do it before the axles / gear die

Interesting tidbit… the fastest spinning object made by man is/was a tiny ball of silicon dioxide. Scientists got it spinning to 300 BILLION times per SECOND. Crazy.

@Robinxon

2 жыл бұрын

How do you even measure that :D

@AiOinc1

2 жыл бұрын

When will Lego reach this

@GazRsExtremeBrickMachines

2 жыл бұрын

When you’re feeling proud of 100,000 and then you read this lol :)

@RazvanYON

2 жыл бұрын

Do you think how many hp this will pull of?

@GazRsExtremeBrickMachines

2 жыл бұрын

At a guess a lot less than 1 HP lol. Whilst these motors offer great torque as they’re geared down once you add some gearing like here you realise just how weak they are! I guess it’s due to the power supply more than the actual motors themselves though! :)

At these speeds, balance is quite important. I would recommend using a silver/black sharpie instead of reflective tape to get rpm measurements. Also, that tachometer you are using will give inaccurate results if it's not held steady. Try attaching it to a stable platform instead of holding it in your hand.

@rigdigwus

8 ай бұрын

lmao the tape won’t influence shit

@gibbled0

8 ай бұрын

@@rigdigwus Let's say the tape has a mass of 0.1g and has a center of gravity 1mm away from the rotation axis (since it's wrapped around the outside of the tube instead of being a point mass). 100,000 rpm converts to 10472 rad/s so the centripetal force on that piece of tape is (10472 rad/s)^2 * 0.0001 kg * 0.001 m = 10.97 N or 2.47 lbf. Assuming the rod it's spinning on is perfectly balanced, that means this piece of tape is constantly pulling that rod to one side with ~2.5 pounds of force at the tip. That's quite a lot of additional friction to overcome at the bearing interface, not to mention vibration.

@CptEric

8 ай бұрын

@@rigdigwusAmerican moment

@GamingWithNikolas

8 ай бұрын

​@rigdigwus you clearly have no understanding of physics.

@sigmamale4147

7 ай бұрын

@@gibbled0 lol you think lego gears are balanced from factory ?

Well the next logical step is to rig a system to release a propeller at max speed. Imagine the height it could achieve.

@x3onz

2 жыл бұрын

propellers don't really work properly when they spin too fast

@WarChallenger

2 жыл бұрын

@@x3onz true, but you could continuously angle the propellers as they keep going faster. 100k RPM IS a bit much, but with a big enough prop, we can translate the kinetic energy along the blades as they counteract air resistance. The larger the rotor, the more momentum too, so we could see it fly upwards for a while.

@x3onz

2 жыл бұрын

@@WarChallenger actually, you'd need a very small propeller to achieve such high rpm

@sel4785

2 жыл бұрын

The propeller would require a far higher torque as well, even disregarding the weird physics you're gonna have to deal with at those speeds.

@multi-mason

2 жыл бұрын

I think the principle could be adapted to great effect. There nay sayers are just hung up on traditional propellers. A disk similar to a frisbee could be enhanced with some propeller like properties that could be tuned due high rpm. Or maybe something that employed less traditional flight mechanics like the coanda effect…

Assuming you have a disk with a diameter of 10 cm, you would have to reach about 65000 RPM to break the speed of sound, that would be incredibly awesome.... Amazing video by the way, as always.

@GazRsExtremeBrickMachines

2 жыл бұрын

Hey there cheers! I really hope to achieve this! Unfortunately I don’t think the thing spinning can be Lego unless I use a Lego sticker lol :) I think it will have to be something ridiculously light! I’ll add some more motors and definitely try!

@rs37_

2 жыл бұрын

@@GazRsExtremeBrickMachines Yes, for the spinning thing I would also use something that is not lego, except maybe the lego stickers, that could also be a good idea. It is also important to use as few gears as possible to reduce friction, maybe arrange the motors differently, like the motors in the 1:1 Bugatti Chiron.

@Haagimus

2 жыл бұрын

Found the engineer!

@GazRsExtremeBrickMachines

2 жыл бұрын

I had to use all those gears unfortunately! If I didn’t have 8 yellow input shafts the axles at the bottom would completely twist and break when using the 1:625 ratio. I filmed the assembly after the test and there still is a bit of twisting on those yellow axles(I’m not sure if you can see it on the video but one was bad) The amount of force/torque to move the 625 ratio overwhelms the axles! I’ve seen the Chiron build and I can only think it’s because they’re the PF L motors which have a lot less torque but spin faster. Also most of the gears are in play when the torque is extremely high so friction has little effect especially with the oil etc . However I realised the last 2 sets of gears at the top I could just use a single cog instead of doubling up as that would reduce friction there quite a bit :)

@waldolemmer

2 жыл бұрын

@@GazRsExtremeBrickMachines If you use a long string the tip should reach the speed of sound

"Hey, can you come over?" Not now, babe. I'm spinning at 100k rpm. "My parents aren't home." 5:16

@itsrubesusnotalbesus

2 жыл бұрын

Mf

Amazing! You have really pushed this (in a pure way) to unbelievable levels. I can't wait to see what you do next...

Legends say: The piece that flew away is still spinning to this day

Man, this is some of the best Lego content out there. Always love it when a new Extreme Brick Machine video pops up. I wouldn't have thought it possible to get those kind of RPM, but if anyone was going to show it's possible, it would be you. Thanks for sharing Gaz 👍

@GazRsExtremeBrickMachines

2 жыл бұрын

Hey Lee I really appreciate that thank you! As always :)

Who ever would have thought that you can spin a Lego at 100,000 rpms! Great work!

@GazRsExtremeBrickMachines

2 жыл бұрын

Hey cheers Josiah, after my last test I didn’t think I would do it! Now I reckon 150,000 is possible with a bit more power :)

It’s called precision toolmaking and design I am surprised no plastic melted on the experiment. Well done

i like how you still keep the speed meter focused on the end even tho a high speed lego got launched. that's true dedication

The fact that it can go this fast, with what appears to be only official Lego pieces(unless you are using BuzzWiz motors) is incredible. If you want to go even further, you could mirror this and connect it to the other side. However, if you want to achieve speeds higher than this, you might need heat treated axles or metal axles.

@joachimtheboss5326

2 жыл бұрын

mirroring would result in 2x the torque not 2x the speed. unless the motor torque is insufficient for achieving the required torque that the system needs to achieve the speed limit in which case mirroring would result in sufficient torque for every motor to spin at their maximum speed

@degtyarev708

2 жыл бұрын

@@joachimtheboss5326 The poor motors are seriously struggling for enough torque according to GazR, and the theoretical versus real RPM backs that up. Meanwhile everything else is struggling with too much torque lol. Damn cool just how ridiculously over the top the guy has gotten these things to perform.

I absolutely LOVE gear ratio and high rpm videos, especially with lego, just seeing how far the limits can be pushed. I wish there was a world record leaderboard for this kind of thing, "fastest rpm with lego" to promote competition and push the limit as high as possible. Edit: I'm so excited for trying to break the speed of sound with lego too!! That's such a cool idea

@GazRsExtremeBrickMachines

2 жыл бұрын

Hey there thank you so much I love doing this stuff too :) some competition would be great as well but I feel bad using all these motors if others haven’t got them! The speed of sound challenge maybe a step too far but I can’t wait to try!

@ouzoloves

2 жыл бұрын

definately with different categories (much like speed running games), with lubricant, without lubricant, which motor, how many motors etc.

@declanfitzgerald1005

2 жыл бұрын

I think a competition like that would eventually boil down to who has the best lube and most motors. but i guess you could do motor divs and focus on gear arrangements

@3DPrinterAcademy

2 жыл бұрын

@@GazRsExtremeBrickMachines I'll have to try 100k+ RPM with a 3d printed gearbox, but 20k is already difficult enough!!

That sounded like a dentist's drill towards the end. Not surprising, given those tend to spin at ludicrous speeds as well (seeming speeds in the 180K RPM range). While each mechanism does have a distinct sound due to its own setup, it does seem like speed overrides that past a point. Interesting.

Sulfur hexafluoride at room temp has a very low speed of sound, is somewhat obtainable and safe-ish, plus because it is heavy you could fill a tub and do final high speed test to get an insane mach number out of lego. It is a very potent GHG though, like super mega Godzilla CO2 so use sparingly after maxing in air ❤ chilling below room temp also reduces speed you need/will give even higher mach number. Room temp to -40c with air you only need 88% speed for mach1, Ideally you would run a vacuum to remove ""all"" the air and then just squirt in a tiny amount of SF6 in an industrial cool room to have min drag of gas and be able to get the highest mach number to make the ultimate lego mach record. HYPERSONIC LEGO MACHINE!

@barneymcwhat6241

2 жыл бұрын

an amusing technicality to be sure, but i think it can be assumed that by "breaking the speed of sound" they mean the speed of sound _through air under standard atmospheric conditions_. not that your science is invalid, but this doesn't seem like the sort of channel that would attempt to claim victory by deliberately setting the bar lower :)

5:20 I had to think of that helicopter song.

for reference, a dremel power tool operates at around 25000 rpm. that's CRAZY FAST

@GazRsExtremeBrickMachines

2 жыл бұрын

Hey thanks for that! That’s crazy for a power tool!

@JohnSmith-pn2vl

2 жыл бұрын

not really, actually thats normal for routers etc

@notgray88

2 жыл бұрын

@@JohnSmith-pn2vl Well yes, normal for power tools, not legos.

@slome815

Жыл бұрын

Dremel is 33000 rpm. Routers usually about 18000-25000rpm.

This was an absolutely amazing mechanical engineering and physics experiment! It is just incredible how gear ratios work and how different configurations can affect the way the gear train behaves. Such an amazing video! Thank you so much for sharing this true inspiration! Kind regards, George

@GazRsExtremeBrickMachines

Жыл бұрын

Hey George thank you so much for that :)

@GQNissanPatrol_TD42

Жыл бұрын

@@GazRsExtremeBrickMachines You are very welcome!!!!!

I seen a lot of people do this, but I’ve never had the idea that you could have multiple motors so that it doesn’t strain.

Seeing the growth of those gears at that speed would be really interesting. Nice work.

This is just absolutely crazy. Never thought stuff like this could be made from legos. Bravo!

@jackieglade

2 жыл бұрын

yo

@GazRsExtremeBrickMachines

2 жыл бұрын

Hey hey thank you for watching, always enjoying seeing you reply too :)

@sirrichardpumpaloaf8154

Жыл бұрын

No such word as legos, it’s LEGO

WHY NOT JUST GO FOR 1 MILLION RPM WHILE YOU'RE AT IT?

@Andre.gaming.corner

Ай бұрын

Bro chill. I think it's impossible

“Breaking the speed of sound with Lego” This would definitely be a video I’d also watch.

@giovform

2 жыл бұрын

just make a whip out of lego

Woah... That 23k RPM swablade is gonna cut anything...

@zarro9848

2 жыл бұрын

@K A D Y 📽️ your mum

@FrietjeOorlog

2 жыл бұрын

Not spinning in reverse like that.

@ManOverboard

2 жыл бұрын

The fact that it's edge moves at 312 km/h is impressive, considering it's a lego machine

@mickyr171

2 жыл бұрын

Im more interested in taping an ant to the outer rim, getting it to go super sonic speeds then releasing it back into its colony if it survives lol, it would find walking at normal speed depressing and probably let off some kind of unique pheromone that would disrupt the entire colony, would be an interesting experiment

With paper saw wheels that fast you could probably cut some oak.

@GazRsExtremeBrickMachines

2 жыл бұрын

I will definitely try this with the better drivetrain! :)

Would love to see this on a table saw style design to see if it can physically cut material. Awesome job ☺️

3:45 Not gonna lie, it sound like a thing when a dentist is digging your tooth

In 3:32 the wheel: RIP

@intouchkhaoviset9155

Жыл бұрын

What happened?

@arthur_philyppis

9 ай бұрын

​@@intouchkhaoviset9155the yellow part went to backrooms

That’s so awesome!! What an amazing design! What an amazing design too, as always man keep up the great work!

@GazRsExtremeBrickMachines

2 жыл бұрын

Hey Easton thank you as always! I enjoyed this one and I’m so glad people are watching a big portion of the video too! It still surprises me! But you had faith from the start lol :)

@eastonchristensen3601

2 жыл бұрын

@@GazRsExtremeBrickMachines I knew you were going to blow up, I mean you had 1 thousand subs when I started watching your vids, and they where all amazing and so well done, I knew it was going to explode, and it definitely did, and will continue on, great job!

@GazRsExtremeBrickMachines

2 жыл бұрын

Thanks again :) I do like the way it’s progressively building up! Sometimes a viral video can do channels more harm than good weirdly. I’ve learnt recently it can be a bad thing having a lot of subscribers if only a small percentage watch regularly as they lower your click rate making it hard for any video to do well! When you originally said 100,000 subs I never believed it was possible in my wildest dreams so thank you :)

@eastonchristensen3601

2 жыл бұрын

@@GazRsExtremeBrickMachines your literally so close!!! It’s crazy!

That sound is absolutely terifying, I was so not ready for that. I was no joke having to grab my chair everytime it got to high rmp

I’ve built a 1:39 hand crank gear assembly, but this, this is amazing

This is absolutely fantastic! You’re taking Lego to the next level. Very well done. 👍

@GazRsExtremeBrickMachines

2 жыл бұрын

Oh thank you so much! I’ll keep on pushing it :)

I feel like having it built as a tower, all the wheels are pressing with their entire weight on the parts bellow them, resulting in high friction. Can you turn it horizontal? And use a high speed grease.

@GazRsExtremeBrickMachines

2 жыл бұрын

Hi, Everything free spun so smoothly and when you spun it fast the device actually lifts up due to the forces at play which takes any load off those bottom cogs. I totally understand where you’re coming from though but in person you would see :) you actually have to pin it down like I did with those two outer beams to stop it floating up! It’s weird lol I’ve done other tests with these devices sideways and the big problems is there’s more load on the axles going downwards into the beens which then creates serious friction welding! Check my other rpm test to see. I used silicone lub, also WD40 and 5w 30 engine oil which gave the best protection 😀

Bro it's amazing, many many thanks to u for all your effort ☺️☺️👍👍

Wow. Great video and I am honestly surprised the plastic did not fly apart due to friction and centrifugal force at that speed.

Wow those gears turned into a rocket there for a second! Thank goodness you where using lubricant otherwise I’d ont think the lego would’ve survived Can’t wait for the speed of sound project! Keep it up!😎👍👌

@GazRsExtremeBrickMachines

2 жыл бұрын

Cheers Nick as always! if I’m honest the axles still didn’t hold up well lol. I had fun doing this, the sound was mad in person! 😀

100,000 rpm equals to around 1,666 revolutions per second. The French: pathetic.

Finally i see a person actually going for it with spinning things fast with technic legos.

Honestly thankyou for the sound warning! 👌

I think you may have won the Lego rpm war with this one Gaz. That was brilliant, dangerous, ground and Lego breaking all at the same time. Glad you had gloves on, and glad you made the video & uploaded so we can all see how much mad engineering went into it. Did you film then reverse it? 👍🍺🇬🇧.

@GazRsExtremeBrickMachines

2 жыл бұрын

I never thought of that Carl, I rebuilt it again lol. And cheers appreciate it! My only wish was the sound of the big white rim would have come across in the video! It was deafening! But it came across as the quietest!😀🍺

@carlbModels

2 жыл бұрын

@@GazRsExtremeBrickMachines it was a sound I understood from my brushless kit. It's a sound that says power. How did the "bearing" surfaces stand up to the torque at the motor end, and the power at the top end? Yeah build something and then dismantle on film and everyone thinks You're even more of a genius builder! I need a beer, have been hooning and it's errrr, hard work! I saw a rev machine that Colin Furze did, that launches a tyre. I bet if you did they with Lego it would fire it miles 👍🍺🇬🇧

@GazRsExtremeBrickMachines

2 жыл бұрын

I’ll check that out Carl I did try the tyre launch but struggling to make a video of it. It was pretty crazy, it hit the wall and literally climbed up it! Then back down and half way up again with rubber left on the wall! Everything was in perfect order other than the last axle(every run damaged at 1:625) and I damaged the two beams holding it in place. Btw hooning? New to me! The more I do on KZread the more beers I need 🍺🍺😀

All you would need is to add something with a radius of 4cm and the tips would be above Mach 1. For comparison the fan of a turbofan jet engine spins around 2000-3000rpm, even the turbopumps on the RL-10 rocket engine only spin at 40000rpm (it is expander cycle though so low mass flow means low speed pumps). Nonetheless. This is fast

What amaze me the most is the precision of lego blocks. Slight disproportion would ruin the whole construction at this speed.

Imagine a lego rc car with this as the gearbox

damn, I sense some torque! Have a feeling about 27 motor 42099

@Athens69420

2 жыл бұрын

Hey GaZR, the bots are all around here in the comment section please report them.

@GazRsExtremeBrickMachines

2 жыл бұрын

Haha imagine that! I am planning a 40 motor Truck soon! :) I think I’ve removed most now! I don’t get how normal comments can get spammed by KZread but not these!

@Athens69420

2 жыл бұрын

@@GazRsExtremeBrickMachines I'm speechless now. 40? 40?! 40?!!!!!! FR🤯😱

@GazRsExtremeBrickMachines

2 жыл бұрын

It will be quite powerful lol. The plan is to pull a car or my nieces on a trailer! :)

@Athens69420

2 жыл бұрын

@@GazRsExtremeBrickMachines BREAKING NEWS: Man build electric pickup by legos appear that it is cybertruck's main competitors.

I'm curious as to how fast one of the big gears would have to be spinning to shatter due to centripetal force. Like shattering a CD

@thatguyalex2835

2 жыл бұрын

Reminds me of the Slo-Mo Guys. :) They destroyed a CD using centripetal force.

@jefftank3300

2 жыл бұрын

@@thatguyalex2835 Exactly!

@thatguyalex2835

2 жыл бұрын

@@jefftank3300 Mid 2010s nostalgia right there (2015). Lol...

The facets of the design are not only brilliant for gauging the mahine but also a testament of beauty in engineering.

@GazRsExtremeBrickMachines

Жыл бұрын

Oh wow thank you very much for the comment :)

You are so positive, I love your builds! You deserve a like and a subscribe!

YOU HAVE ACHIEVED THE IMPOSSIBLE!!!!!

@heathb4319

2 жыл бұрын

If it was impossible...he couldn't achieve it. Just food for thought. He as actually achieved the not yet accomplished. ;)

Looks like I got what I wished for :D I hope you didn't get hit by the flying lego pieces.

@GazRsExtremeBrickMachines

2 жыл бұрын

😀 I actually took some care this time! Eye protection etc! It was quite intimidating especially that old white wheel! The sound was deafening but it didn’t fully come across on the video :)

Amazing! I want more of this stuff 😛 I have subscribed 👍🏻

I do sometimes query why I seem to waste so much time pursuing trivia of late. The someone comes along and roundly clears my conscience completely thus removing all self-doubt...

The dc motors inside of these lego motor can spin about 15000rpm itself There will be a lot of power loses. Motor power > geared down into 300rpm >geared up to 100000rpm. (Sorry for my bad English)

@GazRsExtremeBrickMachines

2 жыл бұрын

Oh great I didn’t know that! Thank you for the info :) Your English is good too!

1:09 The nearest and the farthest gears do nothing as they are not connected "upstream". 6:19 Reaching the speed of sound at 102,465 rpm = 1700 rps it will take a disk with circumference of about 20 cm i.e. diameter of 6 cm. You might have already achieved that.

@gnashr4366

2 жыл бұрын

At 1:09, dont the nearest and furthest gears help to distribute the torque as they are connected to the system with tiny gears?

@user-oh2kt8lf6g

2 жыл бұрын

@@gnashr4366 You are right. I just watched slow motion of the assembly process and noticed there were two axis stubs visible atop of the traverse bar.

It's amazing that the plastic doesn't melt, the parts must actually get extremely hot with this fast rotation!

My man’s gonna reinvent electricity

It's over 100.000!

Maybe you could try fitting that in a vacuum?

@BHARGAV_GAJJAR

2 жыл бұрын

Good point it will spin even faster perhaps in vaccum.

@GazRsExtremeBrickMachines

2 жыл бұрын

I’ll have to check out bricks video to see how he did! A good future project :)

I've never been afraid of a LEGO Technic machine before like I was while watching this video.

Dentist: "It won't hurt." The drill in my mouth:

It needs to launch a beyblade.

I have never feared Legos before this video. It felt like it might explode at the end. 👍 for an awesome video!

That is very sweet! I was waiting for it to melt and fuse together at any second. To bad you don't my day's Legos. Lets see you open and close a little green door a hundred thousand times a second! Never stop learning!

4:45 The sound of lego motors humming in harmony

3:32 haha you got scared! So did I :D

@GazRsExtremeBrickMachines

Жыл бұрын

😂

Damn! I'm really amazed as to how those Lego gears can take-on all those rpms without breaking!

i do want to ask, among the many projects you've done, which has broken the most componets?

5:08 Bayblade! Let it rip!

@Unknowntraveler302

Жыл бұрын

The final evolution of Pegasus

The real hero is the reflective tape that didn't get yeeted to oblivion during the test.

I remember I got a Lego technic set when I was like 9, since it wasn't compatible with my regular Legos it immediately went to the bottom of the toy box, periodically watching your videos makes me regret that, and not joining robotics class in 6th grade lol, and not taking computer class in Jr high, and not joining the stem course in high-school, and all my other life choices lol

really great Thanks for taking the time to make the video and share it

@GazRsExtremeBrickMachines

Жыл бұрын

Hey there thanks for the lovely comment, means a lot cheers :)

This is for someone who finds the sound of the motors humming so satisfyyingggg……..😂

I can't be the only one that's tempted to touch it while it's spinning at max speed

bro will never stop until he reaches 1.000.000 RPM

I would have thought the spinning force would have split the gear apart, but it held up. I remember splitting oranges by spinning them as a kid. All that juice moves to the outside and boom, it splatters everywhere. lol. Not a lot, but still had to clean up.

Man, what? When I was a kid, I don't remember these kinds of advanced pieces. I've seen you do things with things that I didn't know existed in Lego.

its funny how you can see the lego sawblades teeth bend down because of the centrifugal force. it really shows how fast this thing is going considering that’s a relatively thick piece of plastic

amazing that those plastic's hold up against the friction

The Ultimate Beyblade launcher! LOL 😁😂 All jokes aside, I am _seriously_ impressed with these Lego gears! The fact they didn't just immediately strip each other of their teeth, or just fracture right off the axles is astonishing!! Way to go Lego quality control 👍

The noises coming off of this thing are terrifying.

You were so preoccupied with whether or not you could, that you didn't stop to think if you should

Add propeller to the top and measure how much thrust each one does

In a very rare circumstance, 6 minutes well spent on KZread.

I'm amazed at the lack of a bigger explosion. Lego plastic is amazing quality

Is it just me or does anyone also love the sound of the motors struggling? It sounds like some kind of an ICE in a train I don’t know where I got that comparison but it just sounds like it...

I believe the reason the hub dropped down on the Axle at max rpm was the centrifugal force was so great it caused the ID of the hub to expand outward losing grip on the Axle

Figured it’d sound like a Honda at 3 am. Not disappointed. 😁😁😁😁 Thank you!

Since you mention wanting to break the sound barrier: Afair the aerodynamic forces start to become a problem already at mach 0.8 (so it would be good to do it in a vacuum). Apart from that, even the load from just holding together whatever you are trying to spin might be too much for plastic. It's not even easy to replace the plastic by steel or aluminium, since steel is quite heavy, so while the it can take more stress, it also has more mass that pull outward. So yeah, be carefull with this, because whatever you try to spin is prone to rapid unscheduled dissassembly - so take some protective measures for that event. We designed something for a research setup that needed to spin with 60 - 90k RPM, so yeah, I know what I'm talking about. Also: This is more or less the regime where turbopumps (vacuum pumps) are operating. Amazing machines ^^

"Hello Doctor" "What happened to your fingers sir?" "I cut myself on Legos"

I was like yeah right when I saw the title, and ended with holy shit, WHAT THE HELL that is so awsome!

Absolutely Amazing!!! Now use this lego wheel to create another saw which can cut through even harder stuff

I love watching engineers with wayyy to much freetime

6:02 it went to 24,275 on the bar which meant it was actually 121,375 rpm

Cool video. Do you use a lubricant at all? The friction/heat must be significant - how do you stop the plastic from melting?

@GazRsExtremeBrickMachines

8 ай бұрын

Hi Chris, yes I used some oil every run on the last axle. Without it starts to melt at around 15-20,000 rpm depending on the load. It got quite messy lol

Nuts how much the saw blade sounds like a genuine table saw

love these types of videos

Anything spinning that fast and comes apart is going to be lethal!

the yellow wheel: nah imma disconnect ill brb

speed of sound... he woke up and said "i am become death, the destroyer of Legos"

The fastest RPM is 600 million and that is just mind blowing. 2013, scientists at the University of St. Andrews made headlines by propelling a tiny sphere to a record-breaking 600 million rpm (revolutions per minute). This new object out-spins that by a factor of 100.Sep 10, 2018