Spindle Replacement - Boat Trailer. Tie Down Engineering Eliminator 3500 lbs Torsion Axle.
Жүктеу.....
Пікірлер: 19
@breid19662 жыл бұрын
Outstanding video! It's exactly how I have replaced these in the past. Excellent explanations and not just the how but also the why. Too bad other DIYers don't make their videos the same. Thanks bunches for sharing!
@CNArea51 Жыл бұрын
I just removed my spindle and I am installing the new one right now... Anti Seize and 100 ft LB OK I'm doing it Thank You C.K. Excellent process ...
@fv_Haymaker4 жыл бұрын
Thank you. Very straight forward video. I have the same axle on a my home-built boat trailer.
@rogerfl2007 Жыл бұрын
Great video, i did mine today. tomorrow i will do the replacement of other side. thanks
@sarahfox8685 Жыл бұрын
I find it easy to get the keys out by putting the nose of the pliers through the loop on the Carter key and tapping the pliers
@marvinbordelon5278 Жыл бұрын
Thank you. Excellent video.
@phiday47603 жыл бұрын
Wow.
@brod123132 жыл бұрын
Also, should the hole in spindle that shoots out the grease from zerk fitting be on top? Bottom? Doesn't matter??? Ty
@yogi799
2 жыл бұрын
i do not believe this makes any difference
@jesusgarciaponce7467 Жыл бұрын
Dónde puedo conseguir un eje de ésos
@TheSilverSurfisher3 жыл бұрын
This vid became more so.....uh.........pornographic around three-eighths of the way through (@ 11:10)... c'mon I can't be the only one to be twisted enough to notice...his demeanor and voice/accent/commentary.... the visuals....no? ...okay, I'm terrible. LOL!!! Great Video only one of its kind...that shows tapered spindle install- so thanks so much!
@randyb94834 жыл бұрын
Is that #84 spindle?
@yogi799
4 жыл бұрын
I've seen them go by so many different names, it was extremely confusing. took me a week to verify what i needed. I think the answer is YES, but the place i bought it from (and many others) call it: ELIMINATOR 1750 SPINDLE, PART NUMBER 80324. that said, they go by another p/n as well. very confusing.
@brod123132 жыл бұрын
When trying to put 100 foot lbs, the whole damn spindle spins inside on me!??? Any suggestions
@yogi799
2 жыл бұрын
you talking tightening or loosening, from the outside or inside of the wheel? more context/details pls. are you changing your spindle or just removing castle nut etc.
@yogi799
2 жыл бұрын
you must be talking about 12:34 when i am installing castle nut at the back after new spindle was inserted. make sure the castle nut spins freely on the spindle, that is #1. any friction will cause spindle to spin too. Next make sure the spindle was inserted as tight as possible into the hub.
Пікірлер: 19
Outstanding video! It's exactly how I have replaced these in the past. Excellent explanations and not just the how but also the why. Too bad other DIYers don't make their videos the same. Thanks bunches for sharing!
I just removed my spindle and I am installing the new one right now... Anti Seize and 100 ft LB OK I'm doing it Thank You C.K. Excellent process ...
Thank you. Very straight forward video. I have the same axle on a my home-built boat trailer.
Great video, i did mine today. tomorrow i will do the replacement of other side. thanks
I find it easy to get the keys out by putting the nose of the pliers through the loop on the Carter key and tapping the pliers
Thank you. Excellent video.
Wow.
Also, should the hole in spindle that shoots out the grease from zerk fitting be on top? Bottom? Doesn't matter??? Ty
@yogi799
2 жыл бұрын
i do not believe this makes any difference
Dónde puedo conseguir un eje de ésos
This vid became more so.....uh.........pornographic around three-eighths of the way through (@ 11:10)... c'mon I can't be the only one to be twisted enough to notice...his demeanor and voice/accent/commentary.... the visuals....no? ...okay, I'm terrible. LOL!!! Great Video only one of its kind...that shows tapered spindle install- so thanks so much!
Is that #84 spindle?
@yogi799
4 жыл бұрын
I've seen them go by so many different names, it was extremely confusing. took me a week to verify what i needed. I think the answer is YES, but the place i bought it from (and many others) call it: ELIMINATOR 1750 SPINDLE, PART NUMBER 80324. that said, they go by another p/n as well. very confusing.
When trying to put 100 foot lbs, the whole damn spindle spins inside on me!??? Any suggestions
@yogi799
2 жыл бұрын
you talking tightening or loosening, from the outside or inside of the wheel? more context/details pls. are you changing your spindle or just removing castle nut etc.
@yogi799
2 жыл бұрын
you must be talking about 12:34 when i am installing castle nut at the back after new spindle was inserted. make sure the castle nut spins freely on the spindle, that is #1. any friction will cause spindle to spin too. Next make sure the spindle was inserted as tight as possible into the hub.
It's 2019 ever hear of cordless drivers?
Wow.