Would help if there was captions explaining what was actually happening

Moto X4 with Springer Case First time I try to apply/install a screen protector. I tried to follow the instructions, but this thing is simply difficult to install. This was an absolute disaster; it was quite difficult from the beginning. I think some written instructions would help a lot. For some reason when I tried to clean the screen with the supplied cloth, there was some kind of dust all over the screen, which seemed some kind of residual stuff from the clothe (the phone is brand new, I removed the new plastic cover for the first time). I applied lens cleaner and it was much better. Then I think I saw some kind of particle on the sticky side of the protector so I tried to remove it with one of the dust removers (stickers) they provide; I made a mess, the protector immediately got a dirty appearance and I left some fingerprints all over the glue on the protector. I continued to install the protector, it didn’t look that bad, pretty much no bubbles, but the places where I left my fingerprints were quite evident (some dirty appearance). There was a spot where I felt some kind particle under the protector, I couldn’t remove even with Silicone squeeze. Then I decided to remove the protector and give it a second try. This time the results where hideous, lots of bubbles, dirty appearance everywhere, bumps. I think I even left some mark (scratch) with the Silicone squeeze (the fabric on one side of the squeeze got worn out). I will wait for the results until tomorrow, but I highly doubt it will look good.

Tried this. Not bad at all, fits perfect and easy to install. Still, have some dust on the edges because of micro-fiber I used to smooth the edges. Edges better be smoothed with the squeegee or even fingers, then no dust, good there are two pieces of protector

Just installed on s9, worked great, initially worried about edge but wiping repeatedly (a few more times than the video) say 15x per side and it has stuck down well. Be careful with the micro-fibre squeegy as the corner on mine left some channels behind where I worked out some bubbles. They aren't very noticeable and I hope they fade with time... and I always have the other from the package! Initially felt way too sticky but as it has cured (10 minutes) it already feels smoother and similar to a glass screen.

I just applied this yesterday and while it's not as good as GLAStR Curved Tempered Glass....it's better than nothing. It was also easy to apply following the techniques below. My suggestions for improving the technique seen in this video. 1. To avoid fingerprints, wear laboratory type disposable gloves. 2. Take the phone out of the case so that you can properly scrape the cover slip over the edges of the phone. 3. Don't overcoat the cover slip with the spray as seen in this video. First test out the spay stream to see how far away the fine mist is generated. (it's a crude spray nozzle that does not emit an even fine mist). Then hold the cover slip at a distance to only capture the fine mist. 4. After placing the cover on the phone and aligning it...again only spay a fine mist over the top cover. 5. You don't need to draw an imaginary line with the scraper. Simply start in the middle with the scrapper and scrape outwards towards the edges. Work from the middle out towards the edges. DON'T USE TOO MUCH PRESSURE during scrapping. 6. Once the NeoFlex film is snuggly secured, wipe over it starting in the middle and out towards the edges with a dry blue paper towel or felt dry cloth. Lay the phone down and allow it to dry for at least 30 minutes. 7. Give it about 3 hours for the clarity to become 100%. I'm not sure why Spigen didn't make a GLAStR Curved Tempered Glass for the S 20+, however the NeoFlex is better than no protection and the clarity and screen touch sensitivity are as good as if I had no cover on it.

@radite2177

3 жыл бұрын

Hello.. Im about to purchase this product for Huawei P30 Pro. You said the clarity of this protector is good, is there any degradation on color quality or color reproducing? Im afraid of the screen protector will make the quality of the screen reduced in terms of clarity, sharpness and color

@tvc1531

3 жыл бұрын

@@radite2177 Hi Radite, I've not experienced any color degradation on color quality or color reproducing. The good thing about this screen protector is if bubbles start to appear weeks later due to not properly applying it...you can lift the edge until you reach the bubbles and smooth it back down without having to respray it.

@radite2177

3 жыл бұрын

@@tvc1531 thank you for your answer !! :) Purchased today and love it already, the video and your tips really helps me on applying procedure. Color and clarity still awesome too !! Thank you very much and have a nice day !! :D

@dotagamer5925

5 ай бұрын

@spigen .... Please PIN 📍 this comment 😊

I had it on now for my s8, it work wonderful.

Que es el liquido que viene con el protector? Casi se me agota y necesito comprar mas para colocar el otro protector que viene en el paquete

First time buying from Spigen and it applied so well with almost no knowledge on how to put it on. Definately buying from the again when I need to.

The initial bubbles went away after half a day or so, but the screen is not as crisp as without a screen protector, or with a glass protector. Will it be better, or is it the best result from a plastic protector?

Seems so complicated, but I love all Spigen's products.

IMPORTANT NOTE: Remember to apply the squeegee gently. It's completely normal for some white spots to remain after applying the screen, and it needs some sort of 1-2 day curing process. After 1 week, the screen no longer feels soft and rubbery.

Ask me a question: this Spigen screen protector covers the iris led sensor and the S8's proximity sensor. Does this pose any problems during use, such as putting your phone near your ear and the display still on (dialing with your ear)?

My neoflex is on my phone for 3 days now. I can see small dust around the perimeter of the protector. Can I pull it off, and reapply the protector? I'm kinda obsessed about the neatness of my phone.

Just applied this screen protector on my S9... and no problems here... you do have to apply it on with a the case over the phone in order for it to work properly (i used a spigen tough armor case)... follow this video to the tee like i did... the only thing different i did was wait 2hrs... then use the phone till it heats up... like 1440 at 60fps videos...🔥🔥🔥🔥🔥 and the finished product was astounding... even took out the micro scratches all over the screen... dont know why people are having problems with the application... cuz this was my first time applying this type of screen protector... 🤷‍♂️🤷‍♂️🤷‍♂️🤷‍♂️🤷‍♂️

Please review Spigen Kuel OneTap TS36 and explain why it's different/better from AP12T. Thanks!

Just by rubbing the edges, it has created micro fractures that looks like small dots. Also the screen had a micro dot damage prior to the installation and I can see a little dot that didn't go away when trying to re apply the screen.

Applied the second one of these from the 2-pack I got when I got my phone. Following the video made the installation a breeze, and my phone looks brand new again!

I got a small crack area at one corner. I think this solution may not suit me as wet solution may seep into screen right? I looking for protector to reduce further damage

I read peoples reviews on Amazon and they said this wouldn't work with the Tough Armor Kickstand one.

I put it yesterday on my new S9+ and it was perfect!

Worked great. Need to have patience

Just got one for my Note 8. Hope it works out.

WHy is it so hard for these companies to make a curved glass screen protector in 2017???

@deeloii

7 жыл бұрын

LethalPhatGuy The answer is in your question. It is so hard lol

@SpigenWorld

7 жыл бұрын

Sadly, there are many complexities to the matter. The rigid nature of the glass is not only incompatible with curved edges but every phone screen is slightly different in every device so not universally compatible. However, despite the choas, we're currently testing to create the right one so we hope to see you in our social media channels for updates!

@umarraheel9182

7 жыл бұрын

Humans have gone to mars invented AI Robots but can't make a glass protector for curved phones A FUCking glass protector!

@SimmeringPotpourri

7 жыл бұрын

Humans have only sent probes to Mars, several which have failed to make it there successfully and although we have AI (Apply to robots where needed), there really not all that intelligent. So, I suspect when we successfully put people are Mars because we have to escape the AI Robot uprising, curved glass screen protectors will probably be a thing. ;-)

@tonycummings4588

7 жыл бұрын

I had a curved one for the s6 edge and it fitted perfectly, also had one for the gear go which had a curved screen

With these rolled edge phones you need a screen saver built into the case otherwise it lifts at the edges dirt builds up underneath and keeps lifting .

Did he/she put a water spray before applying the screen protector on the phone??

I'm going to hear the music from this video in my nightmares. FML

I have a samsung galaxy s9 plus does this neo flex screen protector will work with my spigen liquid air case..?

will the rainbow effect go away because I just applied mine and it's bothering the help out of me???

Even after reading other peoples negative comments I still thought I would give these screen protectors a try, especially as Sigens cases are great. I could not be more disapointed. After 3 days I have removed the protector due to the lack of clarity the protector has, the orange peel effect and all the micro scratches it has picked up in a short space of time. I will be going back to Samsungs original screen protectors and I recommend not buying these ones.

@fetterchinese24

4 жыл бұрын

Where can i buy original screen protectors?

@rduivestein

4 жыл бұрын

@@fetterchinese24 Amazon or Samsungs website

Can this be removed and reapplied say, 3 days after installation? Or only before the adhesive sets?

Looks like a marvellous product! Are there any other cases that are within my budget (£10) that work well with this Spigen screen protector? Thank you 😊

I feel down. I'm now on my fourth screen protector and have been putting in on with the Spigen case but days later it always starts to pull away in the bottom left corner. I feel like I need a microscope to do it correctly :(

Do you put the wet side down, surely this can't that difficult to show?

What kind of liquid is used here?

What's the difference between this neo flex and the neo flex HD or are they the same thing

Life makes so much more sense now! Put the phone in the case and then apply the protector....

@randomescu

4 жыл бұрын

Ill put the most phone-covering case i own for best guidance

@hella6892

4 жыл бұрын

Sarcasm!? It makes no sense to me at all - it makes the application even worse because now u wont see the edges of your screen anymore AND all the excess liquid will run between the phone and the case. I think the did trat so people buy their covers too!.. Not cool spigen

@withmygoodeyeclosed

4 жыл бұрын

@@hella6892 The phone is water resistant.. just wipe it dry afterwards. I just installed this one on my S9 and it was very easy to do so. And Spigen is allowed to make screen protectors that fit their cases. It's pretty hard to make a universal screen protector because of the curved edges and not all cases wrap around the edges the same way.

@hella6892

4 жыл бұрын

@@withmygoodeyeclosed i know..^^ think about it twice maybe you get it. Im not interested on those spigen screen protectors anyway..;) i have installed a much better protector for months and no need for a spigen ... !

@hella6892

4 жыл бұрын

@@withmygoodeyeclosed but if you need a camera lens protector go with spigen. These are superior to all the other lens protectors;)

Spigen, is this screen protector compatible with Spigen Tough Armor case ?

Does it work with all cases or just cases made by spigen

Will this be available for the new Moto G Stylus? Also is Spigen going to be making a Rugged Armor case for the Moto G Stylus? I've had one of those great cases on my last 3 phones

Very disappointed. Love the cases, but jesus, this was difficult. After the first protector stretched out after pushing the air bubbles out, i applied the second one only the the same thing to happen. Now I have a distracting rainbow streak through the middle of my screen due to the stretch. The actual action of moving air bubbles that popped up after application stretched the protector!

Is this screen protector compatible with the Spigen S8 Slim Armor CS case?

Is this better than tempered glass and prevent drop?

After to put the neoflex screen protector in which time i can use the cell phone?

Will it peel of if my phone gets wet?

the tempered glass i bought from spigen,everything is fine except the center part, "rainbow/ghost " which i cant take it away even by pressing the part outside the tempered glass.

Any idea how to clean the dust stuck underneath? Its sticking so damn hard to the adhesive

Is there one for the galaxy a8+?

What exactly is that chemical

My Neo Flex HD for Galaxy S10+ came with 2 protectors in one box. The first one expanded before even 1 year. Just applied the second one, hopefully it would last longer.

@noorahmadlondon

Жыл бұрын

so, hows the screen protector looking now?

Hoy se la he puesto a mi movil y el acabado es perfecto, otra ventaja es que mientras está húmeda puedes cuadrarla lo más derecha posible en la pantalla.. me ha gustado 👍like

@maria12308

2 жыл бұрын

Y0

It is compatible with ultra hybrid case?

Will it break out after months on its own ?

im running out of the water applier, can i change it with tap water?

Matte or clear?

estan disponibles esos screen para galaxy s6 edge en colombia??

what is the liquid you use ?

I have just applied the product today, it is amazing I would definitely recommend. There are however a few bubbles around that edges that appear to be multicoloured probably dude to the adhesive, do these disappear after a period of time?

@Cali_MD

7 жыл бұрын

GrayGamingPS4 yes, the liquid drys and disappears. I have had the screen protector on two weeks now and there is no problem. I had a slight liquid bubble at first, but it went away in a day.

@yapolloable

2 жыл бұрын

it doesnt disappear thats the nature of TPU screen protector. For mine it has bubbles forever, you can completely remove it. Garbage product.

But there's still bubbles under the screen. And it gives it the look of having plastic over the screen. Not comparable to glass screen protectors.

Don't take any notice of the negative comments. Easy to install and fantastic results. You've done it wrong if you've not got good results. Highly recommended.

@Alwaysgotthemunchies

6 жыл бұрын

Alan Docherty using liquid is an easy install pfffft ok

@CaptainKostaZ

5 жыл бұрын

Lies it gets dirt

@MrBaracu

5 жыл бұрын

Andrew Li Liquid is bullshit. I saw so many videos of it and it do nothing.

@Alwaysgotthemunchies

5 жыл бұрын

MrBaracu I have a zagg. It was $50 for the privacy protection glass. I’ve bought it 4 different times because it’s so good. Wouldn’t use anything other than the zagg. So easy to put on too

@pasteman

5 жыл бұрын

yeah really nice summary, if the result is bad, the fault is yours.

I ordered this and I didn t get the spray from step 5. Is a mistake or I should order it from somewhere else? Can somebody explain?

This is a good screen protector. What liquid is that? Is it just water?

If you have bubbles wrinkles or any other defects you probably installed it wrong. I received mine yesterday and it is hands down the best screen protector I've used so far. It has only been a couple of days so I'll keep y'all informed if anything goes wrong but it's looking solid. Fun installation too 😁. Oh and by the way I have the spign neo hybrid case

@rikysunshine

6 жыл бұрын

What about the condition now? I have the new Samsung s9 and I don't know if put a screen protector or keep it without...

@crispydosaa

6 жыл бұрын

Update?

@FMFvideos

Жыл бұрын

@@crispydosaa the phone exploded

how to remove the dust that stuck inside the screen protector...i tried to use dust remover does not work...use tha spray not working also...

Thanks, that was really helpful!

For all those who has air on the edges, just warm it up a little with hair dryer and smooth.. Very easy to install ;)

@ToonKuijpers1

3 жыл бұрын

Seriously saved my entire application, thanks.

@Monsieurbreizh

2 жыл бұрын

@@ToonKuijpers1 j

whats inside the adhesion solution? theres not enough in the bottle to make up for mistakes, might have to make my own

This is a great product.

One question... Can i use normal water? My spray was empty after three uses. I don't know why but this was not enough spray for one protector so how can it be enough for two?

@MrBaracu

5 жыл бұрын

Hello? No support?

@simelekeme

3 жыл бұрын

Me too

I would like the name of the case that is demonstrated with the installation of the neo flex please!!!!!!

I got 2 today both was bad, 1 had dirt on it, The other one is outside The Phone on the edge so its peeling off on s20...

Thank you

Better than glass?

seems nice, too bad they do not ship to Cyprus :|

What's the difference between neo flex and neo flex HD on your website? Does it fit on the Liquid Air?

@SpigenWorld

6 жыл бұрын

They're both the same and both definitely remain case-friendly with all our cases.

peel off and redo part was catered for me right lmaooo

idk if mine is a fake tbh....the packaging is different ...maybe its 2018 packaging differs i guess....

Is it okay to use water instead of that spray?

Im ordering this today for my S9. Suggestion: use thin, mulated on hand rubber or silicone gloves.

@marknadin8183

4 жыл бұрын

suggestion: make a DIY spray solution with just distilled water. Idk why Spigen added cleaning stuff to thier solution (it does nothing in fact...)

this is a great screen protector but it's really hard to install it. They did say you can redo it if you mess it up but by the time i took it off it had dust and fingerprints on the sticky side so messed it up. Get someone with accurate and steady hands to do this for you. Great for scratch protection. Once again Spigen saves the day.

@Go-nb9jz

2 жыл бұрын

I creased mine ☠️☠️

@cp136934

2 жыл бұрын

@@Go-nb9jz me neither :(

I used all the spray how to get a new spray only what is the spray substance?

Used all my spray for first dcreem protector. Whats the best sub

@Spigen: Whats the reason for putting a Spigen case on before installation? Please let us know. For me it makes no sense at all..

@Rex-cq1hp

4 жыл бұрын

It’s for better alignment

Mine has really bad rainbow effect.

Do you have a screen guard for samsung m31s

Not sure I did this the right way.. there are still bubbles + the spray goes on the side that goes on the screen? How can that be possible? Im confused

Perfect

After reading all the negative comments I almost returned the neo flex, but since there are 2 in the package I decided to try it anyways. As for the application of it, It was EASY! I did everything they did in this video except I did not put it in a case first. I just got my new S9+ so I left protector on back and didn't take original plastic protector off front until I was ready to apply the neo flex protector. So far its been 12 hours, all small bubbles have disappeared. The edges of the protector sealed quickly and as it appears now, does not look like they will lift. I will come back after a few days to update on how its working after using phone with case.

@Alwaysgotthemunchies

6 жыл бұрын

Melissa Renee I don’t believe you. I think you work for spigen and just said a fake review

@wmw0702

5 жыл бұрын

It's been 4 months now, and you haven't been back yet(?).

@MrBaracu

5 жыл бұрын

Yeah 4 months...

@FrancisNadal7

5 жыл бұрын

6 months... are you dead?

@jeneralgod

5 жыл бұрын

I think shes dead boys

Thank you for making these tutorial videos, they make it much easier for me to know how to use the product as a new customer.

is it okay after touching fingertips are gets there easily ?

What happens if i put the phone in water ?

I ordered some just now, but wet installs doesn't seem like a good idea really. What is the solution made out of?

@Dyscrasia

4 жыл бұрын

Cum

@WXYKE

3 жыл бұрын

@@Dyscrasia I support this message

@Dyscrasia

3 жыл бұрын

@@WXYKE LMAO my comment from a year ago still going

@WXYKE

3 жыл бұрын

@@Dyscrasia yup. First time I broke my phone (through the fucking screen protector by the way) read this, and it's definitely cum.

Is it UAG Friendly.?

Which Spigen case is this?

Is it easy to be scratched?

damn. i spent an hour just for this

get a screen protector for your samsung s8 and s8+ because the screen get scratch easily i got a deep scratch and dont know how i got it

How can i rwturn this Things There was dust already sticking to the protector!!!!

@marknadin8183

4 жыл бұрын

that's your fault. use a room where there's no dust (well, not literally). i.e. a steamed room helps

Thanks for making such a great screen protector. Just put my 2nd one of these on, I love the wet system of putting on, it's so simple and after a week it's all cleared up and looks fantastic, I wouldn't use anything else 👍 perhaps just needs a warning that children would need help to install as it may be a child who wants to put this on their phone and would require assistance. Besides that all good 👍👍👍👍

@marknadin8183

4 жыл бұрын

Don't use the included solution (spigen spray bottle.) It contains glass cleaning stuff which does nothing at all. Just use water (distilled) spray instead. It will do the same job if not better cause then you can spray much more without worrying about emptying the spigen bottle.

@noorahmadlondon

Жыл бұрын

@@marknadin8183 are you sure? are you 100% sure that the solution given is the exact same thing as water?

@____REX

Жыл бұрын

@@noorahmadlondon Yes. With distilled water, feel free to spray everywhere on your phone and the film as much as you like, allowing you to position the film on your phone correctly and EASIER. With the included bottle, you can't literally spray everywhere. And if you made a mistake (I.e. film got your fingerprint or whatever) the included bottle will be less than half... Remove the excess water and dry everything with microfiber cloth. May take hours for the water to completely dry.

I have a problem to apply screen protector on huawei p40 pro. Please help

Boi i cant put my xase back one and its a spigen one