Thanks! I bought the battery and some T9000 glue off of eBay coming to under $30. Was able to replace the battery in 30 minutes. The most difficult part was getting the case apart without marking up the plastic. I have spudgers, but ended up resorting to a sharp kitchen knife like another commenter suggested. I heated it with a hairdryer for about 30 seconds while rotating it around. It took a few tries but I was able to get open.
@themegasalad Жыл бұрын
Great video, saved my buds. You can put the earbud in a water and heat proof plastic bag and then lower the bud and bag into boiling water for a couple minutes to soften the glue instead of a heat gun. Also the contact cleaner isn't needed to remove the battery glue, just use a razor and go really slow so you don't cut the center contact. After that the glue peeled off easily and I was able to use t9000 and just hold the contact down with finger pressure until it dried.
@Jade-St28 Жыл бұрын
This video saved me so much money and frustration. Left earbud had that battery draining issue after the update and it got so bad that it died after 10 minutes playtime. Sony support was no help at all, only citing standard bullshit that it's normal that battery charge may differ between left and right (ya maybe for
@slaxxTB
Жыл бұрын
its about the software, not the batteries... since 1.4.2 they started to drain faster. But usually the right one dies quicker. So its been the last pair of headphones i bought from sony.
@dozieemenike6509
Жыл бұрын
When you replaced it with the zen, did it last?
@Smellslikegelfling
Жыл бұрын
@@slaxxTB I have the exact same issue. I thought it was because I tend to use the right one by itself sometimes. They degrade very quick. I went from having 4 hours to have 2 hours or less in a few months, then finally the right one died completely.
@MonkeyDIvan
Жыл бұрын
Sony is fucking atrocious. In no world should it be acceptable for people to spend upwards of $300 for their earbuds to die so fast. I've been using mine for a little over 1 year, never had any issues and the battery on them were amazing, after the latest firmware updates however I've been facing the same issues as all you people. My leaft earbud will go from 100% to 20% in about 2 hours whereas my right earbud will still be at about 80%. I also noticed the left earbud overrheating when charging. This is genuinely unacceptable, and sadly by now the warranty has expired so I can't ask for any replacements. FUCK. SONY.
@MasterDewey
Жыл бұрын
How long did you have to use the hair dryer on the bud? Mine does not seem to want to open.
@Food-is_Life Жыл бұрын
Wow! You have skills sir. That was precise and smooth the way you took it apart and put it back together. If that was me I would’ve broke it prying the buds apart in the beginning. Lol.
@pdimor9 ай бұрын
Excellent video, i've seen a few others but this one was the clearest to follow. I saw a suggestion somewhere about squeezing the sides after you heat it and that really helped get a spudger in there without gouging it all up.
@uabir8338 Жыл бұрын
Amazing patience and accuracy. Hats off
@0irukalive15 ай бұрын
Thank you for this video! I came here from the walkman blog amaizing article on this battery replacement. Their instructions are great but seeing it in video helps a lot!
@Taganskii Жыл бұрын
благодаря вашей инструкции, заменил батарейки в своих наушниках, спасибо. сони что то сделала, что они умирали за 10 минут со 100% до 0%
@nurzhanorns3305
Жыл бұрын
Подскажите какую батарею поставили взамен старых? Та же проблемы с быстрой разрядкой правого наушника.
@Taganskii
Жыл бұрын
@@nurzhanorns3305 Аккумулятор Varta CP1254 A3
@oranged9122 Жыл бұрын
Thank you for this. i was about to change both of my batteries!
@JumaKevin Жыл бұрын
Thanks for this. Replaced my XM4 batteries and found out you dont really need to remove the small ribbon cable. Mine was too stuck so I ended up carefully removing the battery from below the two ribbon cables and central PCB. Now I can't quite seem to find a perfect glue to hold the two plastic pieces back together! 😂
@NightWarJET
Жыл бұрын
You can try to stick it with T9000 glue.
@abrararifify
Жыл бұрын
Should have listened to you as I ended up ripping my trying to remove it haha
@shabanasayyed643
Жыл бұрын
@@abrararifify so what you'll do now?
@stephensabar1563
Жыл бұрын
How is battery backup after replacing batteries?
@JumaKevin
Жыл бұрын
@@stephensabar1563 My XM4s are like new! Getting full 6 hour sessions with 20-30% charge still left. 12hours total without ANC! I love it!
@SergeCruso Жыл бұрын
Thank you for your video! Was able to repair my dying left earbud!
@dozieemenike6509
Жыл бұрын
Did replacing the left earbuds fix the battery drain issue ?
@SergeCruso
Жыл бұрын
@@dozieemenike6509 it did! I can see the right bud not keeping up but I feel confident to change it when the time comes.
@Decoder7447 Жыл бұрын
Thank you for the tutorial ! I was able to replace the battery on my left earphone.
@HeinekenLasse Жыл бұрын
Thank you sir, following your video I managed to change my batteries
@oyewumiakintomiwa8248 Жыл бұрын
Thanks. Had left bud battery drain issue. This video helped me to change the battery (from aliexpress). Everything is all good now. 🇳🇬
@Will.Tristan
Жыл бұрын
That's good to hear, might have to do the same soon unfortunately. Left side is starting to die quick and Sony might not replace my set since I apparently bought a refurbished pair.
@japanese1763
Жыл бұрын
Mind sharing the battery link from AliEx?
@oricebucket
Жыл бұрын
@@Will.Tristan Does it mean it didnt charge to full?
@Will.Tristan
Жыл бұрын
@@oricebucket it use to charge to full sometimes, then would die within 40 min. I changed the battery now though, same way Yen did in the video. Works great now!
@oricebucket
Жыл бұрын
@@Will.Tristan thanks for the feedback. My problem is that it only charges till 90%. I guess I will change the battery too.
@hkliangming Жыл бұрын
非常感謝你的分享
@BarrosNeto Жыл бұрын
PARABÉNS, MARAVILHOSO (恭喜你,太棒了)😃
@dhomak Жыл бұрын
thanks for the video! very interesting music choice, I have to say! Great, but unexpected
@mrtruch Жыл бұрын
Thanks so much for the video!
@corey7219 Жыл бұрын
I'm curious if the battery in the actual wf 1000xm4 case can be removed easily. I looked at a video on the prior model and the battery is aoldered to the board
@David-rz9dt Жыл бұрын
Hi, could i check what is the pincer with the plastic tips you used? The yellow plastic to remove the contact points internally and finally the cleaner in your red spray? Many thanks
@ej86 Жыл бұрын
I need to do that to my black xm4's it was one of the first batches that had battery issues, mine won't charge to 100%.
@sinill178 ай бұрын
成功了~~ 詳細說明的視頻... 太感謝了... 加油~!! Taiwan (성공했어요~~ 상세한 설명을 담은 영상.. 너무 감사드립니다... 파이팅 대만)
@user-st5rf3hy1r Жыл бұрын
Thanks! It is very help to me!!
@itzikreich Жыл бұрын
Which spudger tools did you use? Can you please share the link?
@wxw4161 Жыл бұрын
Thank you very much. 🙏
@alexanderpopov9801 Жыл бұрын
Hello, could you provide a list of the necessary tools, required to perform this operation? Ideally - an iFixit set, with which one can execute this. :)
@heatherphilips922711 ай бұрын
Great video!! I have now done both sides. The biggest challenge is getting the ear buds open, once you are inside, it's pretty easy with the right tools. The big question. How do we extend the life of these batteries? I'm one of those who charges my iPhone and apple watch ultra to no more than 80-85%, to reduce the wear on the battery's. Unfortunately, I do not think you can set the charging time of the Sony ear buds.
@skullcrusher_1
11 ай бұрын
I'd recommend when you're home to leave them out of the charging case and turn them off using the headphones app
@kellymoses8566 Жыл бұрын
Interesting song choice
@bluegizmo1983 Жыл бұрын
I approve of the sea shanty music 👍 😂
@ScaverDanTTV11 ай бұрын
Thanks bro another pair saved
@POKEMONHK Жыл бұрын
謝謝分享
@sushiNramen Жыл бұрын
Thank you!🎉
@falconlips54746 ай бұрын
1. You don't need to remove small ribbon from PCB on battery, just use heat and alcohol, carefully peel off PCB from battery and reuse adhesive (careful in case the battery is swollen as it may blow with heat) 2. In my experience using B-7000 glue, the repair didn't work long term as there was not enough adhesion and the buds opened over time, i needed to remove the old seal/adhesive (black tacky stuff) and put the glue in its place. 3. Please not this music 😂
@RenarLostsolo Жыл бұрын
Thank you!
@fio7777711 ай бұрын
Has the update that is causing people issues since been fixed?
@porplay7 Жыл бұрын
You are the best.
@NightWarJET
Жыл бұрын
Thank you
@dondonstudent Жыл бұрын
Thanks much !
@tlaloc5506 ай бұрын
Wow excellent video thanks
@ttllvfsh Жыл бұрын
Bought a secondhand non original set (only realize when i got the set). Sony Service Centre in Johor, Malaysia says if it's original set, HQ does offer one to one exchange of the earbuds for batteries draining issue. I would have had to buy a new set if it wasn't for this video. Thank you so much.
@izizree
Жыл бұрын
Really bro? Malaysia sony centre offers for one to one exchange? But that must be in warranty is it?
@sultanarsakor
Жыл бұрын
I am in indonesia , bought it from overseas which has UAE sales printed. Battery drain after 1 year guarantee expired. How could yo know it is recondition or second hand?
@ttllvfsh
Жыл бұрын
@@izizree even passed warranty unit are entitled, but I supposed only certain batch. You should definitely try your luck if you are having the same problem
@sebastien2498
Жыл бұрын
Just sent mine to HQ for a replacement after a year of ownership, no warranty for free. SONY Customer Service has been great to deal with
@izizree
Жыл бұрын
@@ttllvfsh just got mine changed. they replaced left earbud with a new one. i just realized mine is still under warranty. tq for all the info guys
@Sailor-Moon1985 Жыл бұрын
Please tell me what temperature and what air flow were set on the hair dryer and the warm-up time? This is very important information so that everything is neat!
@NightWarJET
Жыл бұрын
Maintain 80-90 degrees Celsius for about 8-10 seconds, don't blow on the same place for too long.
@christopherchew
Жыл бұрын
@@NightWarJET but i still cant open why?~ alrdy 8-10 sec T.T
@marfusha9325 Жыл бұрын
Thanks ❤
@sokalowy10 ай бұрын
Great job and instructions! But did you mount Varta 3.7V battery in XM4? Not soo good idea. XM4 uses 3.85V batteries. Mounting 3.7 will decrease life of battery and working time for the earphone.
@NightWarJET
10 ай бұрын
The customer has shared the usage time during the test; cp1254 A3 is about 3.5 to 4 hours, and Z55H is at least four to five hours.
@3xxibmw Жыл бұрын
Hi. 1 -What temperature should I set in the hotair? Can you blow with a regular heat gun? 2- Are these ZeniPower Z55H batteries from ali recommendable in your opinion? Great presentation of battery replacement.
@NightWarJET
Жыл бұрын
If you can control the temperature, you can blow it around 80 degrees for nine seconds, and you can search for it on the z55h battery auction website.
@3xxibmw
Жыл бұрын
@@NightWarJET In my hot air soldering iron, the minimum temperature is 100 degrees C, but I can do it. Thank you very much for your answer.
@purpledoge4466 Жыл бұрын
what type of glue you used to keep the battery glue to the contacts and the buds themselves?
@NightWarJET
Жыл бұрын
If the original tape is broken, you can tear it off and replace it with ordinary double-sided tape, and the metal contact piece should be exposed.
@cedricvu1460 Жыл бұрын
What came out of the red straw? Is it a kind of solvent? Wd40? Blake cleaner?
@NightWarJET
Жыл бұрын
530 Electronic Contact Cleaner Spray
@polaxmorrikone48279 ай бұрын
Is it possible to supply VARTA CP1454 A3 The dimensions of CP1454 are 14.1*5.4MM, therefore the marking is appropriate. The fact is that the capacity of the VARTA CP1454 A3 is 40% higher than the original, and accordingly, theoretically, the headset should work longer! Will the VARTA CP1454 A3 fit into the connector, given that the height is the same and the diameter is 2 mm larger?
@cesarledesma9647 Жыл бұрын
Gracias!
@mitchgordon8199 Жыл бұрын
Thanks your video helped o7
@jameswong9776 Жыл бұрын
Amazing work. Thanks a lot! However, would like to know if you have used a bit WD40 for removing battery cap? Thanks again!
Freaking awesome music to go with this! What is it?
@NightWarJET
Жыл бұрын
Wellerman (Sea Shanty)
@PurpleWind Жыл бұрын
and I had a cup of tea under the table and the headphones on the table, and with a sharp movement of the mouse I pushed the earpiece and it fell into the cup, dried it out, although the protection level is ipx4
@bertopaglinawan7137 Жыл бұрын
thanks big help
@Xyanel Жыл бұрын
Question, at 2:10 there is what looks like an adhesive + insulation on the PCB, what can I use to replace that? I didn't force it but I kinda messed it up thats why i'm trying to look for replacement for it. Or would it be ok to install without that?
@NightWarJET
Жыл бұрын
You need to use double-sided tape on that side, and there is a metal contact piece in the middle that needs to be dug a hole, which needs to be in contact with the underlying battery to form a path.
@Xyanel
Жыл бұрын
@@NightWarJET can you recommend a double sided tape? I just want to make sure I got the right one
@NightWarJET
Жыл бұрын
@@Xyanel The main thing is to be sticky enough, 3M commercially available double-sided tape should be sufficient. I myself use a specific 3M model: 9448 tape
@RaGeSpectral Жыл бұрын
I'm struggling to open the earbuds, it should be possible to heat the glue with a hair dryer right? or will i need a heat gun?
@NightWarJET
Жыл бұрын
If you don’t have a heat gun at hand, you can also use a hair dryer instead. Be sure to heat it up, for fear that the internal glue is too sticky, and the parts will be broken when you remove it.
@2003AudiS3 Жыл бұрын
Easier to change than airpod batteries
@NightWarJET
Жыл бұрын
That's right, it's much easier to repair than Apple's AirPods.
@user-zr1zp1zg3v Жыл бұрын
Hi, do I have to use the falcon 530? Or is it possible to do without it? In theory, it needs just a little bit so that it is possible to fix the battery back and so that the contact does not disconnect.
@NightWarJET
Жыл бұрын
The 530 is used as a degumming agent, or you can dig out the battery without using a degumming agent and paste the residual glue back.
@user-zr1zp1zg3v
Жыл бұрын
@@NightWarJET ok, thank you
@mtr2192 Жыл бұрын
May I ask what the point of prying that little thing at 2:57 & 7:57 is? It seems necessary but I'm not sure what it is. Thank you!
@NightWarJET
Жыл бұрын
Those are the metal contacts of the positive and negative poles, which are raised a little higher to make the positive and negative poles contact better; but be careful, the metal is very soft.
@silent69696969
6 ай бұрын
if i mistakenly broke the negative pole you speak of, can I do a patch (replace the snapped off pole) with some fine copper wire, as long as it touches the pole plate and battery negative side?@@NightWarJET
@user-iv1iv6wz7t6 ай бұрын
Hello!! I saw the video you posted. And I'm a Sony wf 1000xm4 user. May I know the information of the glue used and the name of the battery?
@NightWarJET
6 ай бұрын
Key words, Z55H battery T9000 glue
@sayfhamdi6355 Жыл бұрын
Probably there will be a problem of low power and and less battery life because of the difference between the original and the new ; old : 3.85v , 0.29wh vs varta : 3.7v , 0.2wh 2:28
@propellerhead2000
Жыл бұрын
I wondered about that myself. I've just replaced the dead OEM cells in my buds. They had 163 hours of use. I had no issue with them until firmware v1.4.2. To replace them I used the same Varta 1254 A3 cells used in this video. It turns out that the Varta 1254 A3 is rated 3.7V, 77mAh (0.2849Wh). With "LDAC/DSEE:Off/NC:On" settings applied the right bud shut off at 4h:57m with 3% still left in the left bud. With those settings Sony rates battery life at "max 5 hours". I'm happy with the swap.
@dozieemenike6509
Жыл бұрын
@@propellerhead2000 did the replaced battery hold up?
@NightWarJET
Жыл бұрын
The one in the movie is cp1254a3, although it can be substituted, but the standby time is shorter
@RaGeSpectral Жыл бұрын
I managed to replace the battery on both buds, but the right one now has "white noise" when the NC is activated. Any suggestion on how to fix it?
@NightWarJET
Жыл бұрын
Not sure what is causing this problem,It seems that the motherboard is faulty, have you tried to reset it?
@RaGeSpectral
Жыл бұрын
@@NightWarJET Yes, but it didn't fix it. I've been reading up and this is a very common problem (even with new ones) and they all ended up using warranty. So I guess I got very unlucky with mine and trigger the issue
@kanaan1007 Жыл бұрын
great job! I have a question, in the beginning I have battery drain issue and the battery life only can hold about 10 minutes in maximum, now it's overheating everytime I charge it, will my problem solved with changing the battery?
@NightWarJET
Жыл бұрын
If the earphone gets into water or falls, it will also cause heat. Ten minutes is quite short. You can try to change the battery.
@dac4770
Жыл бұрын
I suggest you ask for a replacement from Sony. Mine also had the same problem, battery drain extremely fast and getting hot when charging in the case, it also drained the case's battery down to 0% in less than 6 hours. After some research, looks like it may be caused by earlier batch of hardware coupled with a problematic software (firmware version 1.4.2 onward). If those really are the cause, I'm afraid replacing battery would not be able to resolve your issue.
At 0.33, what tool is that, you are using to open the earbud? Is that a "modified" tool?
@NightWarJET
Жыл бұрын
You can google metal dismantling stick
@heatherphilips9227
Жыл бұрын
@@NightWarJET Thank you...Ordered. Another question, what is the black glue that Sony uses to hold the battery? FYI, I have successfully removed the old battery from my right earbud, replace with new one (same ZeniPower Z55H 3.85v as stock) and closed it up. Its quite the project!! It helps to have a lighted desk magnifier, heat gun, the "right tools", and the proper glue to get this project moving along, and most importantly, patience..For those of you out there that think this is impossible, its not. Just keep working at it "carefully", and try not to use metal tools, use plastic picks and priers, and it will come apart. Use heat sparingly! I had 3 cups of coffee before I tackled this project (not recommended to drink coffee before taking this task on), as my hands were shaking the whole time..LOL. I am, however curious as to what that black glue / adhesive is, that Sony uses to hold the battery in place.
@mickhead77 Жыл бұрын
what did u blow on the contact on the battery before removing it ?
@NightWarJET
Жыл бұрын
530 electronic cleaner👌
@mister.07 Жыл бұрын
the cause of it was the software or faulty batteries? bc if I replace it and it is the software that damaged the batteries, it will happen again.
@NightWarJET
Жыл бұрын
It is recommended to update the firmware of the earphones first, and try to replace the battery if the battery is still running out. 🙂
@madness13039 Жыл бұрын
can the old battery be taken out without (what i'm assuming is) the alcohol drop?
@NightWarJET
Жыл бұрын
Heat the heat gun along the seam for about 7-9 seconds, use a relatively thin disassembly tool to pry it open, do not disassemble it forcibly if it is not heated enough.
@himmyneutron5769 Жыл бұрын
Is the T900 permanent in case of having to change the battery again?
@NightWarJET
Жыл бұрын
Spray some 530 cleaner and it is easy to disassemble.
@dozieemenike6509 Жыл бұрын
Can I use spirit or nail polish remover as the degumming agent?
@NightWarJET
Жыл бұрын
Avoid solvents that contain moisture or that may melt plastic.
@lQ13l Жыл бұрын
Слишком рано заклеил, надо было включить на проверку . В друг новые батарейки бракованные и не продержатся хотя бы 5 часов
@itachyc.4285 Жыл бұрын
nice video, i ak stuck, i am unable to open them, doent matter how long i heat them (tryng not too long), any advise?
@NightWarJET
Жыл бұрын
After heating, insert the flat blade into the gap to separate the earphones.
@paulbowditch7511
Жыл бұрын
Found best temperature to be 125C
@NADIM_TD Жыл бұрын
Can I use a hair dryer ? Is this battery as powerful as its original battery and it is rechargeable ?? What happens if you use varta CR 2032 battery ?? Please answer me quickly . 😍😍🇹🇩💙
@djwitek8
Жыл бұрын
You are not able to charge CR2032 battery. It's standard lithium battery, you need lithium-ion battery (Varta CP1254 for example) to charge them 😉
@NADIM_TD
Жыл бұрын
@@djwitek8 Okay, I got it. I gave it to a specialist and it was changed.
@cedricvu1460 Жыл бұрын
I can’t find the 530 electronic cleaner, can i replace it with the wd40 cleaner?
@NightWarJET
Жыл бұрын
WD40 will leave a lot of lubricating oil, which is bad. A spray with high volatility and low residue is required.
@tomo100brt Жыл бұрын
After replacing battery, I tried to discharge them, but they are always 100%. After almost 6 hours they are still 100%. It says fully charged. After 6.5 hours they dischargeed. And when I put them to charger case light is green no orange light. What is wrong?
@NightWarJET
Жыл бұрын
Was it normal before replacing the battery?
@hendry8524 Жыл бұрын
Can recommend where i can buy battery international shipping ?
@NightWarJET
Жыл бұрын
You can search in local google, keyword: z55h or cp1254 A3
@libardomm.trasimaco Жыл бұрын
is it possible to do that without a heat gun? maybe with indirect heat from a stove?
@NightWarJET
Жыл бұрын
You can also use a hair dryer
@Dani741 Жыл бұрын
I cannot read properly the nr of the Varta one is CP 1254 but what is the next one A something...
@NightWarJET
11 ай бұрын
A3
@b5a5m5 Жыл бұрын
1:40 What is this liquid and what is it's purpose? It evaporates quickly... Isopropyl?
@NightWarJET
Жыл бұрын
The 530 cleaning agent sprayed in the video.
@shaneagnew3733 Жыл бұрын
What is the adhesive used? Need a eu equivalent
@NightWarJET
Жыл бұрын
Try T9000 Glue
@daniellr2232 Жыл бұрын
Hello, I'm trying to solve the battery drain issue, my right earbud dies in 20 min. Do u know what caused this problem? And if I change the battery, Can this problem appear again? I'll wait to your answer Thanks for the video, I didn't see another video on yt explaining how do this.
@NightWarJET
Жыл бұрын
If the earphones have been used for several years and feel that they are prone to run out of power, you can try to change the battery.
@wingken40 Жыл бұрын
熱風應該用多少溫度吹?。謝謝指導。太多苦主了
@NightWarJET
Жыл бұрын
熱風槍調90 吹7-8秒
@DuckHugh
Жыл бұрын
@@NightWarJET 吹過頭會怎樣~
@NightWarJET
Жыл бұрын
@@DuckHugh 炸給你看😏
@DuckHugh
Жыл бұрын
@@NightWarJET 那麼誇張!
@7993mick Жыл бұрын
What are you using to seal it back up?
@NightWarJET
Жыл бұрын
Glue with T-9000 glue, pay attention to the amount, avoid glue overflow
@kennethralph1592
Жыл бұрын
@@NightWarJET if you use T-9000 and would need to replace the battery again in the future would you still be able to access it? or would it work like super glue that once you use it you can no longer separate it?
@JohnChua-rh8ge
Жыл бұрын
@Kenneth Ralph u can don't add glue but beware of waterproofing. The left over adhesive should be sufficient if u do not have glue
@10Gidi Жыл бұрын
like number 999 :)
@user-ti6dt1gp9d Жыл бұрын
👍
@djwitek8 Жыл бұрын
What kind of glue did you use?
@NightWarJET
Жыл бұрын
T9000 glue
@TheWalkmanBlog Жыл бұрын
Top work, good to see a proper battery replacement video. question, what kind of battery life are you getting with the varta? it has less voltage and less capacity than the Z55H, is it a significant difference?
@NightWarJET
Жыл бұрын
Specification: CP1254: standard voltage 3.7V, standard capacity 77MAH, diameter 12.1mm, height 5.4mm, weight 1.6g Z55 (1254) 65mAh-75mAh m.zenipower.com/cn/page.html?id=61
@TheWalkmanBlog
Жыл бұрын
@@NightWarJET which cp1254 battery are you using? the A4 version? Since the A3 version is not 77mAh, but ~60mAh. at 3.7v, the batteries might not last as long, not earbud listening time. but the actual life of the battery since you are overcharging it to 3.85v with the case. While it may not be that much of a difference, if a problem arises with 3.7v battery being overcharged too much, it might damage the battery and cause it to explode. Not ideal situation.
@NightWarJET
Жыл бұрын
@@TheWalkmanBlog Most of the headphones I have repaired are A3 version, otherwise they are H55
@NightWarJET
Жыл бұрын
@@TheWalkmanBlog Explosion should be unlikely, unless the charging overcurrent protection of the circuit board is broken
@japanese1763
Жыл бұрын
Dude, I am gonna try your link to downgrade the ver. Before i do this. Thanks for sharing in your blog
@PhongNguyen-uq5rn Жыл бұрын
"Bluetooth device 2 replaced" announce when i touch sensor function after I replaced battery for left. I tried factory reset but that announcement still occur
@NightWarJET
Жыл бұрын
Clean the connecting seat of the upper cover and the lower cover with cotton dipped in a highly volatile detergent, and then re-connect it. I'm afraid that you broke some part during the disassembly process.
@apurbaadhikary8479 Жыл бұрын
Bro from where i can purchase battery for model WFLS900 N..and battery model pls?
@NightWarJET
Жыл бұрын
You can find it on the auction website, keywords: model battery
@BigBoss-gb4cx Жыл бұрын
What glue should we use to make it possible to take it apart if needed next time?
@NightWarJET
Жыл бұрын
You can try B-7000 or T-9000.
@LL-lh7om
Жыл бұрын
@@NightWarJET Hello, AWESOME video! Can I also use a t-7000 glue? Is it the same as a t-9000 or b-7000?
@cedricvu1460 Жыл бұрын
Is the glue conductive connecting the pcb to the battery?
@NightWarJET
Жыл бұрын
That black glue is non-conductive
@cedricvu1460
Жыл бұрын
The glue you put around the earbud is non conductive too right?
@electricblueeyes Жыл бұрын
I already change mine, all is well but still it's not charging, it's the right earbud where there is no battery drain issue, I just switch the buttons on the app to make it have noise canceling now it's not even charging even I change the battery, please help
@NightWarJET
Жыл бұрын
Excuse me, is it the left earphone or the right earphone that cannot be charged? What is the problem before replacing the battery?
@electricblueeyes
Жыл бұрын
@@NightWarJET before I replace the battery of the right earphone it's all okay, until I change the button of it to have anc because as we all know the left earbud have the anc button, I change it because the left earphone is already having battery problem, so back to the right earbuds I change it and now working I think I will be sending it to some third party fixer thanks for the reply
@C.I.A_Unclassified Жыл бұрын
What size battery can I use to replace this as well as the charging case?
@NightWarJET
Жыл бұрын
Either cp1254 a3 or Z55H can be used on WF-1000XM4.
@apurbaadhikary8479
Жыл бұрын
Bro which battery I should use for WF-LS900N? And from where can I purchase it? Alibaba or Amazon..pls help bro
@@NightWarJET Can I use varta cr 2032 ? Please tell me
@traze2k4 Жыл бұрын
What was the fluid you used to remove the board section from the battery?
@NightWarJET
Жыл бұрын
The one on the video is 530 electronic cleaner.
@patriayvida694 ай бұрын
You put in a 3.7v battery, it had a 3.85, the customer is going to come in 1 month to tell you that his battery died again
@grahamtilley3628 Жыл бұрын
What glue did you use?
@NightWarJET
Жыл бұрын
4:54 T9000 glue
@nathanielangelojancamacam7584 Жыл бұрын
Do i need to fullt charge the battery after replacement. My right earbud is not on but it has charging indicator when i put it on the case. Please help
@NightWarJET
Жыл бұрын
Use a three-purpose voltmeter to measure the voltage of the battery. If it is above 3.5 V, it should be able to start the machine. Check whether it is reversed. The metal contact piece cannot be touched. It needs to be adjusted.
@nathanielangelojancamacam7584
Жыл бұрын
Thank you for the reply. Apparently when i glued the earbuds the motherboard was not properly intact so I had to open it again
@burackbb
10 ай бұрын
mine is flashing when you put them into the case too but not turning on after i unplug them. so did you open it again and checked the connections?
@nathanielangelojancamacam7584
10 ай бұрын
@@burackbb yes i have to re open it and re aligned all the part and connection. Working like a charm now
@burackbb
10 ай бұрын
@@nathanielangelojancamacam7584 ok i will try that
@paulbowditch7511 Жыл бұрын
Used a hot air gun to open 3 ear buds. First tried 100C but not luck in opening. Tried 150C which was too hot and started melting the plastic. Found 125C was about right. From experience be careful as easy to pull apart too far and pull the ribbon cables out of their sockets. Anybody experience of alternative types of battery to fit as the originals are quite expensive.
@paulbowditch7511
Жыл бұрын
I've opened a few more since last post and would suggest lower temperature around 115C. Does anybody know the reason why Bluetooth not pairing is beginning to happen with these buds?
@SergeCruso
Жыл бұрын
@@paulbowditch7511 I could see the bud I repaired but no audio so I did the factory resets (hold touch pads for 10 secs, and open and close case 10x until blinking red light and then kept it closed until it showed green)
Пікірлер: 322
Thanks! I bought the battery and some T9000 glue off of eBay coming to under $30. Was able to replace the battery in 30 minutes. The most difficult part was getting the case apart without marking up the plastic. I have spudgers, but ended up resorting to a sharp kitchen knife like another commenter suggested. I heated it with a hairdryer for about 30 seconds while rotating it around. It took a few tries but I was able to get open.
Great video, saved my buds. You can put the earbud in a water and heat proof plastic bag and then lower the bud and bag into boiling water for a couple minutes to soften the glue instead of a heat gun. Also the contact cleaner isn't needed to remove the battery glue, just use a razor and go really slow so you don't cut the center contact. After that the glue peeled off easily and I was able to use t9000 and just hold the contact down with finger pressure until it dried.
This video saved me so much money and frustration. Left earbud had that battery draining issue after the update and it got so bad that it died after 10 minutes playtime. Sony support was no help at all, only citing standard bullshit that it's normal that battery charge may differ between left and right (ya maybe for
@slaxxTB
Жыл бұрын
its about the software, not the batteries... since 1.4.2 they started to drain faster. But usually the right one dies quicker. So its been the last pair of headphones i bought from sony.
@dozieemenike6509
Жыл бұрын
When you replaced it with the zen, did it last?
@Smellslikegelfling
Жыл бұрын
@@slaxxTB I have the exact same issue. I thought it was because I tend to use the right one by itself sometimes. They degrade very quick. I went from having 4 hours to have 2 hours or less in a few months, then finally the right one died completely.
@MonkeyDIvan
Жыл бұрын
Sony is fucking atrocious. In no world should it be acceptable for people to spend upwards of $300 for their earbuds to die so fast. I've been using mine for a little over 1 year, never had any issues and the battery on them were amazing, after the latest firmware updates however I've been facing the same issues as all you people. My leaft earbud will go from 100% to 20% in about 2 hours whereas my right earbud will still be at about 80%. I also noticed the left earbud overrheating when charging. This is genuinely unacceptable, and sadly by now the warranty has expired so I can't ask for any replacements. FUCK. SONY.
@MasterDewey
Жыл бұрын
How long did you have to use the hair dryer on the bud? Mine does not seem to want to open.
Wow! You have skills sir. That was precise and smooth the way you took it apart and put it back together. If that was me I would’ve broke it prying the buds apart in the beginning. Lol.
Excellent video, i've seen a few others but this one was the clearest to follow. I saw a suggestion somewhere about squeezing the sides after you heat it and that really helped get a spudger in there without gouging it all up.
Amazing patience and accuracy. Hats off
Thank you for this video! I came here from the walkman blog amaizing article on this battery replacement. Their instructions are great but seeing it in video helps a lot!
благодаря вашей инструкции, заменил батарейки в своих наушниках, спасибо. сони что то сделала, что они умирали за 10 минут со 100% до 0%
@nurzhanorns3305
Жыл бұрын
Подскажите какую батарею поставили взамен старых? Та же проблемы с быстрой разрядкой правого наушника.
@Taganskii
Жыл бұрын
@@nurzhanorns3305 Аккумулятор Varta CP1254 A3
Thank you for this. i was about to change both of my batteries!
Thanks for this. Replaced my XM4 batteries and found out you dont really need to remove the small ribbon cable. Mine was too stuck so I ended up carefully removing the battery from below the two ribbon cables and central PCB. Now I can't quite seem to find a perfect glue to hold the two plastic pieces back together! 😂
@NightWarJET
Жыл бұрын
You can try to stick it with T9000 glue.
@abrararifify
Жыл бұрын
Should have listened to you as I ended up ripping my trying to remove it haha
@shabanasayyed643
Жыл бұрын
@@abrararifify so what you'll do now?
@stephensabar1563
Жыл бұрын
How is battery backup after replacing batteries?
@JumaKevin
Жыл бұрын
@@stephensabar1563 My XM4s are like new! Getting full 6 hour sessions with 20-30% charge still left. 12hours total without ANC! I love it!
Thank you for your video! Was able to repair my dying left earbud!
@dozieemenike6509
Жыл бұрын
Did replacing the left earbuds fix the battery drain issue ?
@SergeCruso
Жыл бұрын
@@dozieemenike6509 it did! I can see the right bud not keeping up but I feel confident to change it when the time comes.
Thank you for the tutorial ! I was able to replace the battery on my left earphone.
Thank you sir, following your video I managed to change my batteries
Thanks. Had left bud battery drain issue. This video helped me to change the battery (from aliexpress). Everything is all good now. 🇳🇬
@Will.Tristan
Жыл бұрын
That's good to hear, might have to do the same soon unfortunately. Left side is starting to die quick and Sony might not replace my set since I apparently bought a refurbished pair.
@japanese1763
Жыл бұрын
Mind sharing the battery link from AliEx?
@oricebucket
Жыл бұрын
@@Will.Tristan Does it mean it didnt charge to full?
@Will.Tristan
Жыл бұрын
@@oricebucket it use to charge to full sometimes, then would die within 40 min. I changed the battery now though, same way Yen did in the video. Works great now!
@oricebucket
Жыл бұрын
@@Will.Tristan thanks for the feedback. My problem is that it only charges till 90%. I guess I will change the battery too.
非常感謝你的分享
PARABÉNS, MARAVILHOSO (恭喜你,太棒了)😃
thanks for the video! very interesting music choice, I have to say! Great, but unexpected
Thanks so much for the video!
I'm curious if the battery in the actual wf 1000xm4 case can be removed easily. I looked at a video on the prior model and the battery is aoldered to the board
Hi, could i check what is the pincer with the plastic tips you used? The yellow plastic to remove the contact points internally and finally the cleaner in your red spray? Many thanks
I need to do that to my black xm4's it was one of the first batches that had battery issues, mine won't charge to 100%.
成功了~~ 詳細說明的視頻... 太感謝了... 加油~!! Taiwan (성공했어요~~ 상세한 설명을 담은 영상.. 너무 감사드립니다... 파이팅 대만)
Thanks! It is very help to me!!
Which spudger tools did you use? Can you please share the link?
Thank you very much. 🙏
Hello, could you provide a list of the necessary tools, required to perform this operation? Ideally - an iFixit set, with which one can execute this. :)
Great video!! I have now done both sides. The biggest challenge is getting the ear buds open, once you are inside, it's pretty easy with the right tools. The big question. How do we extend the life of these batteries? I'm one of those who charges my iPhone and apple watch ultra to no more than 80-85%, to reduce the wear on the battery's. Unfortunately, I do not think you can set the charging time of the Sony ear buds.
@skullcrusher_1
11 ай бұрын
I'd recommend when you're home to leave them out of the charging case and turn them off using the headphones app
Interesting song choice
I approve of the sea shanty music 👍 😂
Thanks bro another pair saved
謝謝分享
Thank you!🎉
1. You don't need to remove small ribbon from PCB on battery, just use heat and alcohol, carefully peel off PCB from battery and reuse adhesive (careful in case the battery is swollen as it may blow with heat) 2. In my experience using B-7000 glue, the repair didn't work long term as there was not enough adhesion and the buds opened over time, i needed to remove the old seal/adhesive (black tacky stuff) and put the glue in its place. 3. Please not this music 😂
Thank you!
Has the update that is causing people issues since been fixed?
You are the best.
@NightWarJET
Жыл бұрын
Thank you
Thanks much !
Wow excellent video thanks
Bought a secondhand non original set (only realize when i got the set). Sony Service Centre in Johor, Malaysia says if it's original set, HQ does offer one to one exchange of the earbuds for batteries draining issue. I would have had to buy a new set if it wasn't for this video. Thank you so much.
@izizree
Жыл бұрын
Really bro? Malaysia sony centre offers for one to one exchange? But that must be in warranty is it?
@sultanarsakor
Жыл бұрын
I am in indonesia , bought it from overseas which has UAE sales printed. Battery drain after 1 year guarantee expired. How could yo know it is recondition or second hand?
@ttllvfsh
Жыл бұрын
@@izizree even passed warranty unit are entitled, but I supposed only certain batch. You should definitely try your luck if you are having the same problem
@sebastien2498
Жыл бұрын
Just sent mine to HQ for a replacement after a year of ownership, no warranty for free. SONY Customer Service has been great to deal with
@izizree
Жыл бұрын
@@ttllvfsh just got mine changed. they replaced left earbud with a new one. i just realized mine is still under warranty. tq for all the info guys
Please tell me what temperature and what air flow were set on the hair dryer and the warm-up time? This is very important information so that everything is neat!
@NightWarJET
Жыл бұрын
Maintain 80-90 degrees Celsius for about 8-10 seconds, don't blow on the same place for too long.
@christopherchew
Жыл бұрын
@@NightWarJET but i still cant open why?~ alrdy 8-10 sec T.T
Thanks ❤
Great job and instructions! But did you mount Varta 3.7V battery in XM4? Not soo good idea. XM4 uses 3.85V batteries. Mounting 3.7 will decrease life of battery and working time for the earphone.
@NightWarJET
10 ай бұрын
The customer has shared the usage time during the test; cp1254 A3 is about 3.5 to 4 hours, and Z55H is at least four to five hours.
Hi. 1 -What temperature should I set in the hotair? Can you blow with a regular heat gun? 2- Are these ZeniPower Z55H batteries from ali recommendable in your opinion? Great presentation of battery replacement.
@NightWarJET
Жыл бұрын
If you can control the temperature, you can blow it around 80 degrees for nine seconds, and you can search for it on the z55h battery auction website.
@3xxibmw
Жыл бұрын
@@NightWarJET In my hot air soldering iron, the minimum temperature is 100 degrees C, but I can do it. Thank you very much for your answer.
what type of glue you used to keep the battery glue to the contacts and the buds themselves?
@NightWarJET
Жыл бұрын
If the original tape is broken, you can tear it off and replace it with ordinary double-sided tape, and the metal contact piece should be exposed.
What came out of the red straw? Is it a kind of solvent? Wd40? Blake cleaner?
@NightWarJET
Жыл бұрын
530 Electronic Contact Cleaner Spray
Is it possible to supply VARTA CP1454 A3 The dimensions of CP1454 are 14.1*5.4MM, therefore the marking is appropriate. The fact is that the capacity of the VARTA CP1454 A3 is 40% higher than the original, and accordingly, theoretically, the headset should work longer! Will the VARTA CP1454 A3 fit into the connector, given that the height is the same and the diameter is 2 mm larger?
Gracias!
Thanks your video helped o7
Amazing work. Thanks a lot! However, would like to know if you have used a bit WD40 for removing battery cap? Thanks again!
@NightWarJET
Жыл бұрын
I use falcon 530 to remove glue.
你好,想請教一下。 1) 1:39 和 7:21 噴的是什麼液體? 2) 4:55 出現的紫色膠水是普通萬用膠還是怎樣的專用膠水? 3) 補回膠水的步驟中,膠水是圍繞蓋邊還是蓋頂塗抹? 剛好右耳的電池故障需要更換奈何是平行輸入不獲保養只能自己動手,苦惱之際幸見此片,還望片主指教。
@NightWarJET
Жыл бұрын
1. 530電子清潔劑 2.T-9000 3.耳機入耳的那側,塗膠用T-9000膠水,注意用量,避免膠水溢出
@NightWarJET
Жыл бұрын
4:52有示範怎麼上膠
@Matthew-jl1ly
Жыл бұрын
成功更換,右耳再次滿血復活了。
@wxw4161
Жыл бұрын
感恩分享,左電池正快速衰竭中,過些時日就照此片更換,再次感謝🙏。
Freaking awesome music to go with this! What is it?
@NightWarJET
Жыл бұрын
Wellerman (Sea Shanty)
and I had a cup of tea under the table and the headphones on the table, and with a sharp movement of the mouse I pushed the earpiece and it fell into the cup, dried it out, although the protection level is ipx4
thanks big help
Question, at 2:10 there is what looks like an adhesive + insulation on the PCB, what can I use to replace that? I didn't force it but I kinda messed it up thats why i'm trying to look for replacement for it. Or would it be ok to install without that?
@NightWarJET
Жыл бұрын
You need to use double-sided tape on that side, and there is a metal contact piece in the middle that needs to be dug a hole, which needs to be in contact with the underlying battery to form a path.
@Xyanel
Жыл бұрын
@@NightWarJET can you recommend a double sided tape? I just want to make sure I got the right one
@NightWarJET
Жыл бұрын
@@Xyanel The main thing is to be sticky enough, 3M commercially available double-sided tape should be sufficient. I myself use a specific 3M model: 9448 tape
I'm struggling to open the earbuds, it should be possible to heat the glue with a hair dryer right? or will i need a heat gun?
@NightWarJET
Жыл бұрын
If you don’t have a heat gun at hand, you can also use a hair dryer instead. Be sure to heat it up, for fear that the internal glue is too sticky, and the parts will be broken when you remove it.
Easier to change than airpod batteries
@NightWarJET
Жыл бұрын
That's right, it's much easier to repair than Apple's AirPods.
Hi, do I have to use the falcon 530? Or is it possible to do without it? In theory, it needs just a little bit so that it is possible to fix the battery back and so that the contact does not disconnect.
@NightWarJET
Жыл бұрын
The 530 is used as a degumming agent, or you can dig out the battery without using a degumming agent and paste the residual glue back.
@user-zr1zp1zg3v
Жыл бұрын
@@NightWarJET ok, thank you
May I ask what the point of prying that little thing at 2:57 & 7:57 is? It seems necessary but I'm not sure what it is. Thank you!
@NightWarJET
Жыл бұрын
Those are the metal contacts of the positive and negative poles, which are raised a little higher to make the positive and negative poles contact better; but be careful, the metal is very soft.
@silent69696969
6 ай бұрын
if i mistakenly broke the negative pole you speak of, can I do a patch (replace the snapped off pole) with some fine copper wire, as long as it touches the pole plate and battery negative side?@@NightWarJET
Hello!! I saw the video you posted. And I'm a Sony wf 1000xm4 user. May I know the information of the glue used and the name of the battery?
@NightWarJET
6 ай бұрын
Key words, Z55H battery T9000 glue
Probably there will be a problem of low power and and less battery life because of the difference between the original and the new ; old : 3.85v , 0.29wh vs varta : 3.7v , 0.2wh 2:28
@propellerhead2000
Жыл бұрын
I wondered about that myself. I've just replaced the dead OEM cells in my buds. They had 163 hours of use. I had no issue with them until firmware v1.4.2. To replace them I used the same Varta 1254 A3 cells used in this video. It turns out that the Varta 1254 A3 is rated 3.7V, 77mAh (0.2849Wh). With "LDAC/DSEE:Off/NC:On" settings applied the right bud shut off at 4h:57m with 3% still left in the left bud. With those settings Sony rates battery life at "max 5 hours". I'm happy with the swap.
@dozieemenike6509
Жыл бұрын
@@propellerhead2000 did the replaced battery hold up?
@NightWarJET
Жыл бұрын
The one in the movie is cp1254a3, although it can be substituted, but the standby time is shorter
I managed to replace the battery on both buds, but the right one now has "white noise" when the NC is activated. Any suggestion on how to fix it?
@NightWarJET
Жыл бұрын
Not sure what is causing this problem,It seems that the motherboard is faulty, have you tried to reset it?
@RaGeSpectral
Жыл бұрын
@@NightWarJET Yes, but it didn't fix it. I've been reading up and this is a very common problem (even with new ones) and they all ended up using warranty. So I guess I got very unlucky with mine and trigger the issue
great job! I have a question, in the beginning I have battery drain issue and the battery life only can hold about 10 minutes in maximum, now it's overheating everytime I charge it, will my problem solved with changing the battery?
@NightWarJET
Жыл бұрын
If the earphone gets into water or falls, it will also cause heat. Ten minutes is quite short. You can try to change the battery.
@dac4770
Жыл бұрын
I suggest you ask for a replacement from Sony. Mine also had the same problem, battery drain extremely fast and getting hot when charging in the case, it also drained the case's battery down to 0% in less than 6 hours. After some research, looks like it may be caused by earlier batch of hardware coupled with a problematic software (firmware version 1.4.2 onward). If those really are the cause, I'm afraid replacing battery would not be able to resolve your issue.
大哥,你太厲害了! 在開外殼時你是用熱氣去除粘膠,但是在取出電池的蓋子時卻用Falcon,請問用吹風機而不用Falcon可以嗎? 謝謝!
@NightWarJET
Жыл бұрын
指的是開蓋還是取出電池的環節?
@oeshoe
Жыл бұрын
@@NightWarJET 電池的環節,你是用Falcon,但是我住在美國還真的沒看過Falcon,所以問用吹風機吹電池的環節會不會有同樣的效果。如果在兩個禮拜前有看到你的視頻,我就可以到你門市請你幫忙,可惜已經回美了!
@NightWarJET
Жыл бұрын
@@oeshoe 其實只要拆機手速快,其實不用再次加溫,用撬棒就能把電池摳起來,因為不太建議直接加熱內部,有電池有機板,風險高
At 0.33, what tool is that, you are using to open the earbud? Is that a "modified" tool?
@NightWarJET
Жыл бұрын
You can google metal dismantling stick
@heatherphilips9227
Жыл бұрын
@@NightWarJET Thank you...Ordered. Another question, what is the black glue that Sony uses to hold the battery? FYI, I have successfully removed the old battery from my right earbud, replace with new one (same ZeniPower Z55H 3.85v as stock) and closed it up. Its quite the project!! It helps to have a lighted desk magnifier, heat gun, the "right tools", and the proper glue to get this project moving along, and most importantly, patience..For those of you out there that think this is impossible, its not. Just keep working at it "carefully", and try not to use metal tools, use plastic picks and priers, and it will come apart. Use heat sparingly! I had 3 cups of coffee before I tackled this project (not recommended to drink coffee before taking this task on), as my hands were shaking the whole time..LOL. I am, however curious as to what that black glue / adhesive is, that Sony uses to hold the battery in place.
what did u blow on the contact on the battery before removing it ?
@NightWarJET
Жыл бұрын
530 electronic cleaner👌
the cause of it was the software or faulty batteries? bc if I replace it and it is the software that damaged the batteries, it will happen again.
@NightWarJET
Жыл бұрын
It is recommended to update the firmware of the earphones first, and try to replace the battery if the battery is still running out. 🙂
can the old battery be taken out without (what i'm assuming is) the alcohol drop?
@NightWarJET
Жыл бұрын
Heat the heat gun along the seam for about 7-9 seconds, use a relatively thin disassembly tool to pry it open, do not disassemble it forcibly if it is not heated enough.
Is the T900 permanent in case of having to change the battery again?
@NightWarJET
Жыл бұрын
Spray some 530 cleaner and it is easy to disassemble.
Can I use spirit or nail polish remover as the degumming agent?
@NightWarJET
Жыл бұрын
Avoid solvents that contain moisture or that may melt plastic.
Слишком рано заклеил, надо было включить на проверку . В друг новые батарейки бракованные и не продержатся хотя бы 5 часов
nice video, i ak stuck, i am unable to open them, doent matter how long i heat them (tryng not too long), any advise?
@NightWarJET
Жыл бұрын
After heating, insert the flat blade into the gap to separate the earphones.
@paulbowditch7511
Жыл бұрын
Found best temperature to be 125C
Can I use a hair dryer ? Is this battery as powerful as its original battery and it is rechargeable ?? What happens if you use varta CR 2032 battery ?? Please answer me quickly . 😍😍🇹🇩💙
@djwitek8
Жыл бұрын
You are not able to charge CR2032 battery. It's standard lithium battery, you need lithium-ion battery (Varta CP1254 for example) to charge them 😉
@NADIM_TD
Жыл бұрын
@@djwitek8 Okay, I got it. I gave it to a specialist and it was changed.
I can’t find the 530 electronic cleaner, can i replace it with the wd40 cleaner?
@NightWarJET
Жыл бұрын
WD40 will leave a lot of lubricating oil, which is bad. A spray with high volatility and low residue is required.
After replacing battery, I tried to discharge them, but they are always 100%. After almost 6 hours they are still 100%. It says fully charged. After 6.5 hours they dischargeed. And when I put them to charger case light is green no orange light. What is wrong?
@NightWarJET
Жыл бұрын
Was it normal before replacing the battery?
Can recommend where i can buy battery international shipping ?
@NightWarJET
Жыл бұрын
You can search in local google, keyword: z55h or cp1254 A3
is it possible to do that without a heat gun? maybe with indirect heat from a stove?
@NightWarJET
Жыл бұрын
You can also use a hair dryer
I cannot read properly the nr of the Varta one is CP 1254 but what is the next one A something...
@NightWarJET
11 ай бұрын
A3
1:40 What is this liquid and what is it's purpose? It evaporates quickly... Isopropyl?
@NightWarJET
Жыл бұрын
The 530 cleaning agent sprayed in the video.
What is the adhesive used? Need a eu equivalent
@NightWarJET
Жыл бұрын
Try T9000 Glue
Hello, I'm trying to solve the battery drain issue, my right earbud dies in 20 min. Do u know what caused this problem? And if I change the battery, Can this problem appear again? I'll wait to your answer Thanks for the video, I didn't see another video on yt explaining how do this.
@NightWarJET
Жыл бұрын
If the earphones have been used for several years and feel that they are prone to run out of power, you can try to change the battery.
熱風應該用多少溫度吹?。謝謝指導。太多苦主了
@NightWarJET
Жыл бұрын
熱風槍調90 吹7-8秒
@DuckHugh
Жыл бұрын
@@NightWarJET 吹過頭會怎樣~
@NightWarJET
Жыл бұрын
@@DuckHugh 炸給你看😏
@DuckHugh
Жыл бұрын
@@NightWarJET 那麼誇張!
What are you using to seal it back up?
@NightWarJET
Жыл бұрын
Glue with T-9000 glue, pay attention to the amount, avoid glue overflow
@kennethralph1592
Жыл бұрын
@@NightWarJET if you use T-9000 and would need to replace the battery again in the future would you still be able to access it? or would it work like super glue that once you use it you can no longer separate it?
@JohnChua-rh8ge
Жыл бұрын
@Kenneth Ralph u can don't add glue but beware of waterproofing. The left over adhesive should be sufficient if u do not have glue
like number 999 :)
👍
What kind of glue did you use?
@NightWarJET
Жыл бұрын
T9000 glue
Top work, good to see a proper battery replacement video. question, what kind of battery life are you getting with the varta? it has less voltage and less capacity than the Z55H, is it a significant difference?
@NightWarJET
Жыл бұрын
Specification: CP1254: standard voltage 3.7V, standard capacity 77MAH, diameter 12.1mm, height 5.4mm, weight 1.6g Z55 (1254) 65mAh-75mAh m.zenipower.com/cn/page.html?id=61
@TheWalkmanBlog
Жыл бұрын
@@NightWarJET which cp1254 battery are you using? the A4 version? Since the A3 version is not 77mAh, but ~60mAh. at 3.7v, the batteries might not last as long, not earbud listening time. but the actual life of the battery since you are overcharging it to 3.85v with the case. While it may not be that much of a difference, if a problem arises with 3.7v battery being overcharged too much, it might damage the battery and cause it to explode. Not ideal situation.
@NightWarJET
Жыл бұрын
@@TheWalkmanBlog Most of the headphones I have repaired are A3 version, otherwise they are H55
@NightWarJET
Жыл бұрын
@@TheWalkmanBlog Explosion should be unlikely, unless the charging overcurrent protection of the circuit board is broken
@japanese1763
Жыл бұрын
Dude, I am gonna try your link to downgrade the ver. Before i do this. Thanks for sharing in your blog
"Bluetooth device 2 replaced" announce when i touch sensor function after I replaced battery for left. I tried factory reset but that announcement still occur
@NightWarJET
Жыл бұрын
Clean the connecting seat of the upper cover and the lower cover with cotton dipped in a highly volatile detergent, and then re-connect it. I'm afraid that you broke some part during the disassembly process.
Bro from where i can purchase battery for model WFLS900 N..and battery model pls?
@NightWarJET
Жыл бұрын
You can find it on the auction website, keywords: model battery
What glue should we use to make it possible to take it apart if needed next time?
@NightWarJET
Жыл бұрын
You can try B-7000 or T-9000.
@LL-lh7om
Жыл бұрын
@@NightWarJET Hello, AWESOME video! Can I also use a t-7000 glue? Is it the same as a t-9000 or b-7000?
Is the glue conductive connecting the pcb to the battery?
@NightWarJET
Жыл бұрын
That black glue is non-conductive
@cedricvu1460
Жыл бұрын
The glue you put around the earbud is non conductive too right?
I already change mine, all is well but still it's not charging, it's the right earbud where there is no battery drain issue, I just switch the buttons on the app to make it have noise canceling now it's not even charging even I change the battery, please help
@NightWarJET
Жыл бұрын
Excuse me, is it the left earphone or the right earphone that cannot be charged? What is the problem before replacing the battery?
@electricblueeyes
Жыл бұрын
@@NightWarJET before I replace the battery of the right earphone it's all okay, until I change the button of it to have anc because as we all know the left earbud have the anc button, I change it because the left earphone is already having battery problem, so back to the right earbuds I change it and now working I think I will be sending it to some third party fixer thanks for the reply
What size battery can I use to replace this as well as the charging case?
@NightWarJET
Жыл бұрын
Either cp1254 a3 or Z55H can be used on WF-1000XM4.
@apurbaadhikary8479
Жыл бұрын
Bro which battery I should use for WF-LS900N? And from where can I purchase it? Alibaba or Amazon..pls help bro
你好,想請問一下: 網路上看原廠配的Zenipower Z55H 3.85v這顆電池太難找了,買得到的幾乎都是3.7v的,這一點點電壓差距使用上會有什麼明顯差異嗎? 另外假如沒有熱風槍,用一般吹風機代替不曉得可不可行?溫度是否足夠把它拆開?
@NightWarJET
Жыл бұрын
差一點點是沒有感覺的 吹頭的吹風機就能用了,感覺吹上去有點溫熱就可以了,吹太久會融化.
@bs96tom
Жыл бұрын
@@NightWarJET 感謝回答,近期逛巴哈影音板一堆人的wf-1000xm4用久了都出現嚴重電池衰退問題,還沒過保的還可以去找sony客服處理,過保了就只能自己找看看有沒有坊間的維修站在修、或自己買電池來DIY維修。 雖然我的還沒出現這狀況,但保固期快過了,電池本來就是消耗品,假如想要延長耳機使用壽命總有一天會需要換,我很喜歡這耳機的聲音,假如哪天它的電池真的不行了也是會希望可以換電池繼續用。 另外充電盒的電池可能也同樣會有壽命問題,不過充電盒似乎比較沒那麼精密,拆裝難度應該會比較低。
Can I get an Amazon link to the battery you used?
@NightWarJET
Жыл бұрын
You can search with this keyword: varta cp1254
@NADIM_TD
Жыл бұрын
@@NightWarJET Can I use varta cr 2032 ? Please tell me
What was the fluid you used to remove the board section from the battery?
@NightWarJET
Жыл бұрын
The one on the video is 530 electronic cleaner.
You put in a 3.7v battery, it had a 3.85, the customer is going to come in 1 month to tell you that his battery died again
What glue did you use?
@NightWarJET
Жыл бұрын
4:54 T9000 glue
Do i need to fullt charge the battery after replacement. My right earbud is not on but it has charging indicator when i put it on the case. Please help
@NightWarJET
Жыл бұрын
Use a three-purpose voltmeter to measure the voltage of the battery. If it is above 3.5 V, it should be able to start the machine. Check whether it is reversed. The metal contact piece cannot be touched. It needs to be adjusted.
@nathanielangelojancamacam7584
Жыл бұрын
Thank you for the reply. Apparently when i glued the earbuds the motherboard was not properly intact so I had to open it again
@burackbb
10 ай бұрын
mine is flashing when you put them into the case too but not turning on after i unplug them. so did you open it again and checked the connections?
@nathanielangelojancamacam7584
10 ай бұрын
@@burackbb yes i have to re open it and re aligned all the part and connection. Working like a charm now
@burackbb
10 ай бұрын
@@nathanielangelojancamacam7584 ok i will try that
Used a hot air gun to open 3 ear buds. First tried 100C but not luck in opening. Tried 150C which was too hot and started melting the plastic. Found 125C was about right. From experience be careful as easy to pull apart too far and pull the ribbon cables out of their sockets. Anybody experience of alternative types of battery to fit as the originals are quite expensive.
@paulbowditch7511
Жыл бұрын
I've opened a few more since last post and would suggest lower temperature around 115C. Does anybody know the reason why Bluetooth not pairing is beginning to happen with these buds?
@SergeCruso
Жыл бұрын
@@paulbowditch7511 I could see the bud I repaired but no audio so I did the factory resets (hold touch pads for 10 secs, and open and close case 10x until blinking red light and then kept it closed until it showed green)
可唔可以搵你換電?😂 可以既話收費如何?
@NightWarJET
Жыл бұрын
若是在台灣,可以在底下連結詢問喔👌