I had a Sony LBT-D505 system with an ST-D505 Receiver. It would show the clock flashing 0:00 denoting standby but wouldn’t power up. I followed this guide and changed the big 35V 1000uF electrolytic capacitor for a new Panasonic one. Pushed the power button and it went straight to tuner. Cost £3.45 for a pack of two capacitors and saved the whole system. Many thanks from the UK for sharing your knowledge. I’m most obliged to you.
@waltschannel74653 жыл бұрын
I like the way you used the clue of the standby LED being dim to shorten the troubleshooting.
@12voltvids
3 жыл бұрын
Rule 1 obseeve, look, listen and give it the sniff test.
@alexanderherget63033 жыл бұрын
Of course it is fixed. Excellent. Nicely done! 👍
@taiwanbirdman2 жыл бұрын
Watching your video is informative, entertaining and, addictive!!! Very nice work, Sir!
@ictrepairs69633 жыл бұрын
Nice to see that you always know what you are doing, you really rock dude! I wish I could gain half of your experience.
@12voltvids
3 жыл бұрын
I would hope so. Been doing this almost 40 years now.
@AdrianJayeOnline
3 жыл бұрын
@@12voltvids hahahaha lol
@CrashPilot10003 жыл бұрын
Great Job! And BTW the stereo Cats in the beginning knocked my socks off. They both run the same version of the cat operating system.
@12voltvids
3 жыл бұрын
Stereo.
@zx8401ztv
3 жыл бұрын
CrashPilot1000 , All cats run on " Fuss and food " Ver 1.1 Beta Meow ( Base o.s with hole dig/poo/fill extention ) Selfish modules are also installed, but not always activated :-D
@alexispieltin9379
3 жыл бұрын
Some also have auto tune installed...
@rawr51919
3 жыл бұрын
MeowOS 1.1 :P
@GeorgeGeorge-xj2bc3 жыл бұрын
Capacitors in older electronics dont have a visual damage so you have to check the suspected capacitor with esr meter,personally i have a Thandar TC200 RLC from1993 which measures up to 200uF but has D (dissipation) similar to ESR which was totally unknown this era and can test the capacitors without removing or desolering any pin.Human designed machines with single layer pcb,transformer and analog circuits without any software and other "smart sophisticated" grand b*s.
@leonardosamson50893 жыл бұрын
Nice watching your informative video hoping for more thanks ,,,,,,,,,,,,,,, from the phillippines
@trappn Жыл бұрын
Great video. Sure wish you were the technician trying to diagnose an intermittent main display on a STRDN1080 receiver. This a relatively common problem, but the only video I found was worthless.
@RespawnRestricted3 жыл бұрын
Man you're lucky a good bit of your vids are either Caps or connections nice and simple
@12voltvids
3 жыл бұрын
I guess you didn't see the switch mode power supply go up in flames the other day.
@johnweegenaar73142 жыл бұрын
nice job on a simple fix
@azrinyusoff189 Жыл бұрын
great video as usual....I wish I live near you...i have so many amps, cd players and tape deck that I wish I could send you for repair....
@nickfrench73723 жыл бұрын
Good job in getting that Sony stereo amplifier going,,,very interesting how a capacitor caused the standby power issues,,and it works great after replacing cap,,,and resoldered power transistor too. I wear a led headlamp when it come to needing that much light on soldering repair jobs on electronic circuits. Looks like i see a few exposed wires and terminals on that desklamp,,,are they mains power? Or low voltage? I know it must b real hot there too,,,as I can hear the background noise of the ceiling fan going full speed.
@12voltvids
3 жыл бұрын
It's cooled down a little but it has been hot. I have a headlamp that j use at work all the time but it is a pita in the shop as i am always hitting the camera with it.
@nickfrench7372
3 жыл бұрын
Ok. I guess the camera is mounted on a overhang tripod? As your video recordings are nice and still images.
@12voltvids
3 жыл бұрын
@@nickfrench7372 overhead jib
@nickfrench7372
3 жыл бұрын
@@12voltvids Ah yes,,,i thought it would b on an overhead jib,,,like a crane. Tripod would b getting in the way all the time.
@12voltvids
3 жыл бұрын
@@nickfrench7372 the tripod holding the jib sits next to me. It is essentially 2 tripods strapped together one holds the camera and the other holds the horizontal arm.
@1pilotsteve3 жыл бұрын
My electronics teachers first words were: Everything is battery and ground and 2 always check the power supply... then he showed us how to bypass a hydro meter...
@12voltvids
3 жыл бұрын
Well that would be an old analog meter. Try that now and see how fast someone is out to check it. Smart meters not only report consumption but they also monitor voltage drop. Have a voltage drop on your drop, that isn't being reported as consumption then something is wrong. It could be a bad termination, but the resulting arcing would be detected by the meter, or a loss of power. (to ground or by theft) Either way, a voltage drop that isn't explained by consumption is going to trigger an alarm, and a crew will come out to check. Neighbour works for BC Hydro and was telling me they nabbed a bunch of people that bypassed the meter when the smart meters went in.
@BadMoCo Жыл бұрын
Hello Sir, are you still around making repairs on things like this? I have a Sony 5.1 Stereo Model STR-DE685 and up until recently everything was fine except the center speaker channels that didn’t send out sound. Well a day ago the unit went out and would not display anything. I press power button and can hear the first click and little orange lights turn on but are also dim, but nothing else goes on and no sound, not even the display. Your video seems like I could make the same repair, but I’m not quite understanding which one you switched compared to my unit. I have a multimeter and decent skills, but unfamiliar with the exact way to test it. Not sure if you’re familiar with my unit or if you’ve done this before too. I’d like to get this unit working again and I wasn’t worried about the center channels as much. However if I can fix this I’d love to speak with you. Im not as experience as you, yet I’m sure with a little help maybe I can make the swap like you did here and get it going again. That second click and relay isn’t hitting and the first click is definitely working. I even opened the little cap and can see the click over and contact, but after that nothing other than dim orange lights. My uncle who use to help us with these things passed away and he was the only one I knew that could do this. If you’re still tinkering with things let me know I’d like to be in touch. If you’re in Colorado even better! Lol. Hope to hear from you maybe we can make a new video with your assistance. It seems like it should be easier than it is, I’m just lost on how to diagnose the exact one to swap. Seems like the Same exact problem in a way. Who knows. I can send you pics or a video of my own if it would help. I read Sony has problems like that typically and are easier fixes than not. Prior to this the unit seemed to work pretty well. At worse case scenario, maybe I could send it to you to take a look at. Hoping we can figure this out ahead of that step. Thanks so much for you video it seems helpful, Im just stuck now and it definitely sounds like the same area of issue. Thanks!
@annierenard59543 жыл бұрын
thank you for this video
@mrnmrn13 жыл бұрын
Wow, new feature. Stereo meow in the intro :)
@bones007able3 жыл бұрын
I had one of those...mine was the silver version .... the miniature momentary buttons also fail ... had to replace about everyone on the front panel ....
@Natures_Intentions3 жыл бұрын
Nice easy fix. Thanks for uploading the video.
@12voltvids
3 жыл бұрын
Nice and easy when YOU KNOW WHAT YOU ARE DOING!
@zx8401ztv3 жыл бұрын
I was really supprised that the 1000uF went so low on a linear supply. Switchmodes normally do that, dam switchmodes.
@12voltvids
3 жыл бұрын
You learn something new every day.
@Jared-C2 жыл бұрын
Alright, so I'm working on a Sony STRAV880 right now, and it does something a bit similar. Powers on, stand by light turns on, but nothing really after that. If I leave it plugged in for awhile, I can hear a relay clicking on the back board when I try to change the input (phono, to tape, etc) but that's it. Could I be looking at something similar where the stand by isn't supplying enough power to the rest of the board?
@12voltvids
2 жыл бұрын
Standby is only for remote circuit.
@Jared-C
2 жыл бұрын
@@12voltvids Ah okay. (this is my first time attempting to repair things like this, so I'm still learning a lot. I did start to look through the path after the power supply board and did find a blown resistor. Couldn't see all the stripes on it so I looked it up in the repair manual and ordered some. We'll see how it goes. If it blows again I'll keep digging.
@sh0t7343 жыл бұрын
You ve finnaly updated the intro in stereo cat
@12voltvids
3 жыл бұрын
Was bored and they seemed to be the same duration and sure enough they were. Now to add the other cats to i had have a "bonheiman raphsody" meow.
@haraetsuseb2147 Жыл бұрын
Sony STR-DG520 wont turn on please help
@Nkhosi_Betting Жыл бұрын
Hello Sir . I a Sony Amplifier with no power at all, not even standby light, where do I begin repairing this unit ( DIY )??
@12voltvids
Жыл бұрын
Did you check the fuse
@Nkhosi_Betting
Жыл бұрын
@@12voltvids all the fuse have continuity
@12voltvids
Жыл бұрын
@@Nkhosi_Betting transformer primary.
@Nkhosi_Betting
Жыл бұрын
@@12voltvids there is 230v, but not on secondary ( small transformer next to rectifier )
@Nkhosi_Betting
Жыл бұрын
@@12voltvids the bridge rectifier has no voltage at all, DC or AC, nothing, is that normal??
Пікірлер: 50
I had a Sony LBT-D505 system with an ST-D505 Receiver. It would show the clock flashing 0:00 denoting standby but wouldn’t power up. I followed this guide and changed the big 35V 1000uF electrolytic capacitor for a new Panasonic one. Pushed the power button and it went straight to tuner. Cost £3.45 for a pack of two capacitors and saved the whole system. Many thanks from the UK for sharing your knowledge. I’m most obliged to you.
I like the way you used the clue of the standby LED being dim to shorten the troubleshooting.
@12voltvids
3 жыл бұрын
Rule 1 obseeve, look, listen and give it the sniff test.
Of course it is fixed. Excellent. Nicely done! 👍
Watching your video is informative, entertaining and, addictive!!! Very nice work, Sir!
Nice to see that you always know what you are doing, you really rock dude! I wish I could gain half of your experience.
@12voltvids
3 жыл бұрын
I would hope so. Been doing this almost 40 years now.
@AdrianJayeOnline
3 жыл бұрын
@@12voltvids hahahaha lol
Great Job! And BTW the stereo Cats in the beginning knocked my socks off. They both run the same version of the cat operating system.
@12voltvids
3 жыл бұрын
Stereo.
@zx8401ztv
3 жыл бұрын
CrashPilot1000 , All cats run on " Fuss and food " Ver 1.1 Beta Meow ( Base o.s with hole dig/poo/fill extention ) Selfish modules are also installed, but not always activated :-D
@alexispieltin9379
3 жыл бұрын
Some also have auto tune installed...
@rawr51919
3 жыл бұрын
MeowOS 1.1 :P
Capacitors in older electronics dont have a visual damage so you have to check the suspected capacitor with esr meter,personally i have a Thandar TC200 RLC from1993 which measures up to 200uF but has D (dissipation) similar to ESR which was totally unknown this era and can test the capacitors without removing or desolering any pin.Human designed machines with single layer pcb,transformer and analog circuits without any software and other "smart sophisticated" grand b*s.
Nice watching your informative video hoping for more thanks ,,,,,,,,,,,,,,, from the phillippines
Great video. Sure wish you were the technician trying to diagnose an intermittent main display on a STRDN1080 receiver. This a relatively common problem, but the only video I found was worthless.
Man you're lucky a good bit of your vids are either Caps or connections nice and simple
@12voltvids
3 жыл бұрын
I guess you didn't see the switch mode power supply go up in flames the other day.
nice job on a simple fix
great video as usual....I wish I live near you...i have so many amps, cd players and tape deck that I wish I could send you for repair....
Good job in getting that Sony stereo amplifier going,,,very interesting how a capacitor caused the standby power issues,,and it works great after replacing cap,,,and resoldered power transistor too. I wear a led headlamp when it come to needing that much light on soldering repair jobs on electronic circuits. Looks like i see a few exposed wires and terminals on that desklamp,,,are they mains power? Or low voltage? I know it must b real hot there too,,,as I can hear the background noise of the ceiling fan going full speed.
@12voltvids
3 жыл бұрын
It's cooled down a little but it has been hot. I have a headlamp that j use at work all the time but it is a pita in the shop as i am always hitting the camera with it.
@nickfrench7372
3 жыл бұрын
Ok. I guess the camera is mounted on a overhang tripod? As your video recordings are nice and still images.
@12voltvids
3 жыл бұрын
@@nickfrench7372 overhead jib
@nickfrench7372
3 жыл бұрын
@@12voltvids Ah yes,,,i thought it would b on an overhead jib,,,like a crane. Tripod would b getting in the way all the time.
@12voltvids
3 жыл бұрын
@@nickfrench7372 the tripod holding the jib sits next to me. It is essentially 2 tripods strapped together one holds the camera and the other holds the horizontal arm.
My electronics teachers first words were: Everything is battery and ground and 2 always check the power supply... then he showed us how to bypass a hydro meter...
@12voltvids
3 жыл бұрын
Well that would be an old analog meter. Try that now and see how fast someone is out to check it. Smart meters not only report consumption but they also monitor voltage drop. Have a voltage drop on your drop, that isn't being reported as consumption then something is wrong. It could be a bad termination, but the resulting arcing would be detected by the meter, or a loss of power. (to ground or by theft) Either way, a voltage drop that isn't explained by consumption is going to trigger an alarm, and a crew will come out to check. Neighbour works for BC Hydro and was telling me they nabbed a bunch of people that bypassed the meter when the smart meters went in.
Hello Sir, are you still around making repairs on things like this? I have a Sony 5.1 Stereo Model STR-DE685 and up until recently everything was fine except the center speaker channels that didn’t send out sound. Well a day ago the unit went out and would not display anything. I press power button and can hear the first click and little orange lights turn on but are also dim, but nothing else goes on and no sound, not even the display. Your video seems like I could make the same repair, but I’m not quite understanding which one you switched compared to my unit. I have a multimeter and decent skills, but unfamiliar with the exact way to test it. Not sure if you’re familiar with my unit or if you’ve done this before too. I’d like to get this unit working again and I wasn’t worried about the center channels as much. However if I can fix this I’d love to speak with you. Im not as experience as you, yet I’m sure with a little help maybe I can make the swap like you did here and get it going again. That second click and relay isn’t hitting and the first click is definitely working. I even opened the little cap and can see the click over and contact, but after that nothing other than dim orange lights. My uncle who use to help us with these things passed away and he was the only one I knew that could do this. If you’re still tinkering with things let me know I’d like to be in touch. If you’re in Colorado even better! Lol. Hope to hear from you maybe we can make a new video with your assistance. It seems like it should be easier than it is, I’m just lost on how to diagnose the exact one to swap. Seems like the Same exact problem in a way. Who knows. I can send you pics or a video of my own if it would help. I read Sony has problems like that typically and are easier fixes than not. Prior to this the unit seemed to work pretty well. At worse case scenario, maybe I could send it to you to take a look at. Hoping we can figure this out ahead of that step. Thanks so much for you video it seems helpful, Im just stuck now and it definitely sounds like the same area of issue. Thanks!
thank you for this video
Wow, new feature. Stereo meow in the intro :)
I had one of those...mine was the silver version .... the miniature momentary buttons also fail ... had to replace about everyone on the front panel ....
Nice easy fix. Thanks for uploading the video.
@12voltvids
3 жыл бұрын
Nice and easy when YOU KNOW WHAT YOU ARE DOING!
I was really supprised that the 1000uF went so low on a linear supply. Switchmodes normally do that, dam switchmodes.
@12voltvids
3 жыл бұрын
You learn something new every day.
Alright, so I'm working on a Sony STRAV880 right now, and it does something a bit similar. Powers on, stand by light turns on, but nothing really after that. If I leave it plugged in for awhile, I can hear a relay clicking on the back board when I try to change the input (phono, to tape, etc) but that's it. Could I be looking at something similar where the stand by isn't supplying enough power to the rest of the board?
@12voltvids
2 жыл бұрын
Standby is only for remote circuit.
@Jared-C
2 жыл бұрын
@@12voltvids Ah okay. (this is my first time attempting to repair things like this, so I'm still learning a lot. I did start to look through the path after the power supply board and did find a blown resistor. Couldn't see all the stripes on it so I looked it up in the repair manual and ordered some. We'll see how it goes. If it blows again I'll keep digging.
You ve finnaly updated the intro in stereo cat
@12voltvids
3 жыл бұрын
Was bored and they seemed to be the same duration and sure enough they were. Now to add the other cats to i had have a "bonheiman raphsody" meow.
Sony STR-DG520 wont turn on please help
Hello Sir . I a Sony Amplifier with no power at all, not even standby light, where do I begin repairing this unit ( DIY )??
@12voltvids
Жыл бұрын
Did you check the fuse
@Nkhosi_Betting
Жыл бұрын
@@12voltvids all the fuse have continuity
@12voltvids
Жыл бұрын
@@Nkhosi_Betting transformer primary.
@Nkhosi_Betting
Жыл бұрын
@@12voltvids there is 230v, but not on secondary ( small transformer next to rectifier )
@Nkhosi_Betting
Жыл бұрын
@@12voltvids the bridge rectifier has no voltage at all, DC or AC, nothing, is that normal??