Hi. This would have been a very useful video if you left all the tidbits for later and got to the crux of the video which is to show how you actually cut the plastic without cracking it. I don't think very many people are looking to cut holes in plastic for the same reasons you do. Ok, box cutter, razorblade sharp. Got it! Finally. I would have started video with that boxcutter as a necessary item for this DIY.

@BenjasUberHobby

4 жыл бұрын

Thank you very much for the feed back. This is very good advice!

@eciv2006

4 жыл бұрын

Kumari Karandawala lol

1 yr later its coronavirus time. I need a grow stand to supply me with microgreens and lettuces for salad daily. Cant afford drill and hole saw. Got the knife and followed your directions, thanks a lot.

So good cutting hole ...

Hey man, thanks for the tips. Sorry about all the hate. I think the video was really helpful

@BenjasUberHobby

5 жыл бұрын

Thank you means a lot.

Great video buddy at least you gave it a go. Unlike the begrudgers who disliked the video. Keep up the great work 👍💪

So did you really cut a hole or was this a hole waste of time?

Why so many dislikes ? I think it is a cool video. Keep going on man

@BenjasUberHobby

6 жыл бұрын

Thanks for the encouragement :) No idea why so many dislikes. Maybe has to do with to many parts or maybe the # of times I say umm :) like a noob. Maybe because I did not use a hole saw. Who knows. I'm fine with it :) Only 13 dislikes for 2779 views I will take that every time :) I had no idea that it had so many dislikes but my videos are not top quality and I know it. I do the best I can do and most people are happy with that :) The other normally leave :) But thank you for your encouragement! It is nice to have someone stop by and tell me to keep on going :) My community is GREAT! They support me through thick and thin. I subbed to your channel. I really liked your intro video. It is all about being yourself and being special :) Thank you!! You brightened my day :)

I used a rail compass with a wood ruler. one side had the pint to center - the other was adapted to hole a sharpened finishing nail I cut the hole half way from the front and then from the back - you get a perfect hole - tears in the holes would rip in the heat of the sun...

@BenjasUberHobby

6 жыл бұрын

Thanks for the info. Ya I had trouble with this lid but the container did a little better but there were still issues.

I tried this a long time ago and was too inefficient. I also tried melting a circle with a soldering iron instead of buying a hole saw but was also too slow. However, probably more accurate and faster than cutting a hole. I will probably have to invest in a hole saw.

@BenjasUberHobby

6 жыл бұрын

Yes I don't make that many but i broke down and bought a 18 piece hole saw from harbor freight for less than $20. Says it works with wood and plastic. Looked up the one I bought and it is $16.99 but I feel wherever you buy it they are worth the money. Also get the hole saw started then reverse the drill and it cuts through it much smoother with less clean up :) Thanks for stopping by :)

Awesome mate ,everyone needs to accept it as a basic guide(hence tips and tricks) instead of a "I DO THIS NOT THAT,YOU SHOULD'VE DONE THIS NOT THAT"make your own video if that's the case.Just remember no matter how good you are, SOMEONE out there won't think so.

@BenjasUberHobby

5 жыл бұрын

Thanks for the feed back :) and pointing out some good points :)

What.t did you use this for? I guess I’m a little confused

What do you to cut the plastic lid???

Hole bore saw...... they come in 1.5 and 2 inch.

How did you make the hole Huhh

@80cardcolumn

5 ай бұрын

8:22 Um I er um and uh uh used um a razor blade knife uh um

I need this because I'm cutting a Mermaid Tail Out off This

@BenjasUberHobby

6 жыл бұрын

That's cool :) What are you going to use the Mermaid tail for?

@charisseng6431

4 жыл бұрын

Ana the loner1 ew a girlish girl

@reikinnie7045

4 жыл бұрын

@@charisseng6431 why are you judging someone

he used scissors to cut holes?

@BenjasUberHobby

5 жыл бұрын

I used a razor blade knife

Good video but I can to know how to cut hard plastic not how to prepare it

Get a protractor next time saves you time.

please make the video shorter. Exclude any unnecessary details.

@BenjasUberHobby

6 жыл бұрын

Thank you very much for your feed back and taking the time to comment.

@The_Joker_

3 жыл бұрын

That’s a tad impossible dude, video is what it is. Get used to it.

Please make the video shorter. ( no hate this vid was useful :)

@BenjasUberHobby

4 жыл бұрын

Thank you for the feed back :)

@charisseng6431

4 жыл бұрын

Benja's Uber 1337 Hobby you’re welcome :)

Flip the net cup over, follow the edge with a felt tip. This isn't rocket science, if you accidentaly put a hole 1/4 inch off from the others, the plants won't know or care. Less OCD.... and an actual video where you CUT the lid!

Less use of the "word" umm

@BenjasUberHobby

4 жыл бұрын

TY.

@ucanleaveyourhaton

3 жыл бұрын

@@BenjasUberHobby , ignore the unsolicited feedback... I don’t have a problem with your video 👍🌈

Thanks for the video. But it is too much information. Just go ahead and cut it, that's what we came for

@BenjasUberHobby

5 жыл бұрын

Thank you for the feed back :)

Um um um

@ucanleaveyourhaton

3 жыл бұрын

You try doing a better job then !

Too many talking bro it's irritating

@BenjasUberHobby

4 жыл бұрын

Ty for the feedback.

@eciv2006

4 жыл бұрын

King Edward Gallenero Say man, you’re trying to talk shit but can’t even type a sentence that make sense. “Too many talking” wtf does that even mean?

Waist of time

Waste of time