Soft Sartor for 12v Motor and Powersupply!
👉
ordered my PCBs from JLCPCB,as low as $2, try it and register to Get $54 Coupons here:m.jlcpcb.com?from=Shot
-------------------------------------------------------
Gerber (pcb Schemes)👇
drive.google.com/file/d/115pM...
hi friends in this video i will make a simple DC soft Starter device which can save Electrical device from inrush current .As their name implies, soft-starters ramp up the voltage applied to motor terminals over time, thereby limiting the inrush current and power, which significantly reduces heat buildup.
this soft Starter can be used at inverters Powersupply that has large capacitor bank or something.that takes lot of Ampre but this circuit can reduce that current. by 60%
the timing can be changed by capacitor changeing
10uf = 2 second
50uf = 6 second
Пікірлер: 36
Great amazing 💪♥️
Whoa this one is useful for DC motor project
@Electronic_For_You
Жыл бұрын
Yeas 😊
Excellent !! Thank you. Subscribed.
@Electronic_For_You
5 күн бұрын
You are welcome 😊
Pretty impressive my friend...great job on it best wishes 🙌👍🤝🌞😎
@Electronic_For_You
Жыл бұрын
Thanks ♥️
Nice 🔥👌
@Electronic_For_You
Жыл бұрын
Thanks
Very Useful broo 😊👍and does the circuit get hot ?
@Electronic_For_You
Жыл бұрын
No ! Just resistor get warm 😊
@rishad100
Жыл бұрын
@@Electronic_For_You oooh nice 🙂 thanks ❤️❤️❤️
@Electronic_For_You
Жыл бұрын
Welcome You can build it the diagram is given in video Thanks 👌
@rishad100
Жыл бұрын
@@Electronic_For_You 😊👍👍👍👍
Wonderful 👍👍👍
@Electronic_For_You
Жыл бұрын
Thanks ♥️
Thank you! What components can I replace to use it with 24V?
@Electronic_For_You
7 ай бұрын
Replace the Relay
@styrishrodrigues
6 ай бұрын
Only a 24v relay to be replaced? @@Electronic_For_You
I have a project where I need this to work on a 21v system and the power is always connected, the load just cycles itself on/off. Is that possible?
@Electronic_For_You
6 ай бұрын
I think your Powersupply cannot supply enough current
🙂👍👍👍
Doesn't the resistor get burnt?
@Electronic_For_You
Жыл бұрын
No 😊
excelente trabajo. Gracias!
@Electronic_For_You
Жыл бұрын
♥️
Your title most be The Simple DC Soft Starter 12V Circuit
@Electronic_For_You
Жыл бұрын
Thanks bro ♥️
Using this in a zvs driver
@Electronic_For_You
Жыл бұрын
Good idea 👌 But my ZVS never failed at starting
@Luiz_inventor
Жыл бұрын
@@Electronic_For_You but when I conect to batery it makes a lot of sparks
@Electronic_For_You
Жыл бұрын
Yeas it is a good idea 😊 You can use it but carful ithe current not exceed relay current if exceed then change relay
@Luiz_inventor
Жыл бұрын
@@Electronic_For_You ok
@giorgikevkhishvili5204
2 ай бұрын
@@Luiz_inventor I think theres no need for diod there, thats the sparks reason
This is NOT a soft start circuit & does nothing to limit inrush current when the motor actually starts. Your demonstration at the beginning shows this. Also a multimeter is not the correct instrument to measure inrush current due to its response time. The circuit presented simply delays the switching on of the motor for a short period. When the relay actually switches on the load you will still see the same inrush current to the motor. ANOTHER Fail ! 👎👎👎👎👎👎👎👎👎👎
@Electronic_For_You
22 күн бұрын
The motor starts through the resistor then the relay bypasses the resistor, I think I should have used lower valued resistor for proper soft Start