No video
SNS 345: Viewer Submitted Machining Jobs
This week I have a couple small machining jobs that belong to a couple of my viewers. The first is some motorcycle parts for a frame and suspension. The second job is some plastic blocks that is needed for a C-10 restoration. I'll show a little bit of rapid production on that segment.
Paypal Channel Donation: www.paypal.com...
Support though Patreon: / abom79
My Amazon store where I'm adding many of the tools and products I use in my own shop. Amazon.com/shop/abom79
Visit my second KZread channel where you can follow are travels, camping, RVing, cooking, and bbq!
Abom Adventures / @abomadventures
Пікірлер: 190
That plastic milled up beautifully.
I love that Adam is doing projects for Viewers, it would be cool if the viewers could send photos of their finished work in, so we can see the finished product.
@Sconnie470
3 жыл бұрын
The frame is off to the powder coater. When it's done I'll send Adam a pic he can post if he wants.
@tkrabec
3 жыл бұрын
@@Sconnie470 Awesome! I hope your Bike turns out amazing.
@garthbutton699
3 жыл бұрын
I like that idea,other channels show case what subscribers have made.
Hi Adam, thanks for the great content!... I had an idea: it would be cool if you could share some pics or video of your work in the wild after folks get their parts installed. You could have a segment of: hey remember that thing I did a few months back, here it is in action... I would dig that and I imagine many other folks would too! Again, thanks for what you do. Cheers, Morgan
My Dad always said, it doesn't matter what the tolerance is. Make it the absolute best that you can make it, not just because it makes your customer happy, but because it makes you happy and proud of your work.
Delrin is lovely stuff to machine. I was amazed with the surface finish I could get from even the dullest carbide insert. Pretty much perfect! Sadly the same cannot be said for my metalworking generally but live and learn. I always pick up a useful tip from watching your vids. Thanks for sharing.
@railgap
3 жыл бұрын
And its properties are wonderful - it's my favorite engineering resin - it's basically nylon on steroids. As for machining properties alone - See Also acrylic (use slightly soapy water for cutting fluid and SHARP tooling) - you can actually get near-optical results with plain COTS tools! railgap.blogspot.com/2021/05/machining-acrylic.html
@railgap
3 жыл бұрын
Also, Adam's cut-off saw is nicer than my engine lathe, ferpetesakes. ^_^
@bradyoung6663
3 жыл бұрын
@@railgap Thanks for the tip on the soap for cutting acrylic. I like having tricks like that in the pocket.
So nice that at around the 7 minute mark, SNS tradition comes thru.
@SardarTariqMahmood
3 жыл бұрын
kzread.info/dash/bejne/k6Nqo5lylJTAh9Y.html ,
I had him make some parts for the steering racks on some Porsches that I have and they were exact, spot-on, to what I was hoping for. I was amazed at the quality of the work! The price was very fair as well.
@SardarTariqMahmood
3 жыл бұрын
kzread.info/dash/bejne/k6Nqo5lylJTAh9Y.html ,
HEY, the music is back!! I've really missed it! Thank you so much for bringing it back. Love your channel!!!
Love the fold away stop on your saw. I've been racking my brain thinking about spring loaded gizmos or some how hinging something. But that stop is elegant simplicity. and adjustable to different sizes of stock. Thanks for sharing Adam
at last a you tube video of someone who knows what he is doing as a retired toolmaker i cringe at some of the things i see. well done 👌
This comment has nothing to do with this KZread. It has to do with the work you did for Rucker on his Stoker Engine. I followed that you did an extraordinary amount of work trying to help Keith R. I have noticed comments that are negative about the work you did. Unwarranted! You are one of the great machinists.
@SardarTariqMahmood
3 жыл бұрын
kzread.info/dash/bejne/k6Nqo5lylJTAh9Y.html ,
Good work Adam, Remember, it's not what you make. It's how you make it.
Adam, could you add the speeds, feeds and depth of cut when you are machining. It would help all us amateurs out. Enjoyed watching, Thanks.
I can imagine it's nice to have a dimensionality low pressure job like those spacers as a palette cleanser between more demanding work
LOVE milling or turning Delrin. It always machines so beautifully and it still amazes me just how strong it is. It takes plastic to another level.
@EDesigns_FL
3 жыл бұрын
I'm with you. It's always a pleasure to make something from acetal/Delrin/POM ; just different names for the same product. The only thing better is PTFE.
Very good job & high quality finish. Also with machines well adjusted makes work easy
Nice work, it was something simple but with due attention and precision. I look forward to your next video on Saturdays !! Greetings
It has to be good to have Adam in your hometown. You know it's going to be a job well done
Congratulations Abom79 on a very well produced machining video.
Nice work on the editing adam good to see you trying new ideas to be a machinist and a videographer and editor lol cant be easy. A+
Thank you for sharing. Watched and very much enjoyed.
Face mill gave a perfect finish. Squaring them reminded me a form tool I was to make from supplied ground blanks (HSS) . They were 3 degrees out of square. I had to grind two sides square before I could even start because they wouldn't fit right in my vice . As you may have guessed they were made in China.
Those are riser blocks to raise the bed floor on the C10 when you lower the body... I have a couple of those trucks...
The nylon looks like perfectly machined, pure carbon block. Interesting stuff!
Well darn, you finally made something I could. I would have made the spacer blocks on my table saw and drill press. BUT I would have needed two lengths of stock cause one would have been goofed on. Great video's!
Good to see some small production runs/repeat work, nice mill stops there👍
Thanks for helping you're fans. Great show
Little bit of super glue will keep them align till you clamp. Simple little trick.
Nice work on the high speed footage Adam
Another good one. I like it when you’re doing simple operations, just do it, no need to talk when it’s not necessary.
Them blocks are the squarest thing on this planet
Those OSG helical taps are the best. I have a boat load of them and they are really great for tapping just about any material as they remove the chips out the back.
Be great to see photos with the parts fitted in applications of the stuff you do mate.
Also from Wisconsin. Sounds like you mean “Wan-Naw-Key” (Waunakee) ?
@mradtke66
3 жыл бұрын
@m9 ovich nope. I’m closer to Waunakee 😉
@BigJsgarage
3 жыл бұрын
I'm also from Wisconsin. I'm in Milwaukee.
Как всегда бесподобная работа 👍👍👍👍👍👍👍👍👍
The cutting operation on the band saw was really cool in high speed! 👍💪🙏
Hi Adam, how about an SNS where you talk about how you clamp pieces both on a fixture and direct to table and how the angle of clamps is determined. Thanks for the great videos.
done with a blindfold and one hand tied behind his back...your experience makes it look so easy.
Would be interested in how that plastic holds up under the weight of the bed.
I want that band saw ha. If you could see the state of the one I use at work, twists and turns all over the place, but to be fair it still makes big bits of metal into smaller bits of metal.
Spacer block guy: "The dimensions aren't critical" Abom79: "Fabricate to within ±0.002".
I miss Stella; I hope to see a new pup in your future.
With that stop method you are guaranteeing the amount of material removed is the same but the overall material length may be different for each piece.
@kindabluejazz
3 жыл бұрын
The first outside stop was just set to square the one end, always taking just a small arbitrary amount off. Then he used a stop on the other side (long rod going through the vice) when he was milling to length.
@tylerakerfeldt7220
3 жыл бұрын
@@kindabluejazz there was no second stop when milling. Please give a time stamp where you can see what you’re talking about.
@kindabluejazz
3 жыл бұрын
@@tylerakerfeldt7220 at 16:24 he is using a stop on the outside end. At 16:35 he is using one on the inside (and you see the outside one still on the mill table). You don't see him using the inside stop for milling to length, but you can presume he did and just didn't show it. Besides, he said the size is not critical, and his pro level band saw is already extremely accurate. Despite your lack of confidence, he knows what he is doing, and did whatever was needed to be done.
@tylerakerfeldt7220
3 жыл бұрын
@@kindabluejazz outside stop was for killing and the inside stop was very clearly for drilling the hole position. It’s not a lack of confidence, I’m just stating what I see as a fact given the information in the video.
@kindabluejazz
3 жыл бұрын
@@tylerakerfeldt7220 He used a stop to get the right length of each piece during the cuts on the bandsaw at 11:57. He even mentions that. It's likely that all he was doing on the mill was a saw-cut cleanup pass of a few thousandths. My main point was that you felt a need to judge his process, when he in fact knew and did exactly what he wanted.
I’ve been wondering if you machinists ever run the cutting tool into the chuck very often. Seems like it would be very easy to do.
@k4kfh
3 жыл бұрын
IMO, much easier to bump into the vise or a fixture on the mill than to bump into the chuck on the lathe. Especially drilling, it's all too easy to just kiss the side of a parallel or something on the mill.
I’m wondering if that spring loaded centre would be a good beginner machining job. Seems pretty easy to make.
Thank you Adam I always enjoy watching your videos videos I am from South Africa
I think it was you who said to cut the waste length only after the first tapping *op.* In case your tap tool breaks, then you have material to remake *that* end. Basically, you cut your chances of complete loss by 50%. Just sayin'.
@BigJsgarage
3 жыл бұрын
Marcos Mota That would be correct if you were doing power tapping but in this case he was doing it by hand
Original mounts were sawn wood. Adam squares and blocks all sides to +/- .001” 😂
@SardarTariqMahmood
3 жыл бұрын
kzread.info/dash/bejne/k6Nqo5lylJTAh9Y.html ,
Adam , I like the old formatt . the high speed machining kinda negates why I am watching ! Great work though .. I still ENJOYED !!
Nice video Adam, I like that you sped it up through the repetitive bits. Reminds me of Jimmy. Hopefully if the dude with the shaft and gussets is welding to that shaft he knows it’s 4130 and how to do that properly. If he’s building bike frames I’m sure he has that figured out.
It's good. You're editing from the viewer's perspective. (We're impatient and spoiled.) You really kept it moving! (Not that every video needs to be like that)
From the thumbnail ..I thought that Motorcycle part was actually a modern version of Architectural paper weights to hold down plans
Rad, love seeing an Abom upload. =)
i had no idea you did viewer jobs! :D interesting.....
@brandon2076
3 жыл бұрын
i don't know how one gets in touch with him about it or how he goes about taking jobs. But there's no way he'd have the time to be able to do all the jobs his viewers would have for him, so i bet it's exclusive to some degree
Great little project 👍😎🇬🇧
Great video 👍 like the video edit.
Hello Adam, An entertaining video tonight... looking forward to your next video (No 1,000). Take care. Paul,,
What I wouldn't give to have a machined set of two hole pins made by Adam.
Pretty ASMR filming there. Fun to watch.
Estamos acompanhando, quero ver o final.
Lots of Mechanical Music today. The fine combination of fast motion and your natural production rhythm
Awesome job .👍I like the setup 🔥. plastic leaves burr lines most of the time.👌iam glad you could leave good finish .🌟Ken Machine NC 😊
Did you ever showcase your spring centre you use? be cool to see how you made it Adam
Great content thanks for sharing
Nice work Adam. Really want me some spiral flute taps.... Next project - Chamfer tool like Stefan's @ GTWR or Tom @ Oxtools
Nice work Adam. Great video. Thank you for sharing.
Hey Adam, Just wanted to say hi from Norway, and thanks for making these videos. They are pure therapy for me. I get so relaxed (and educated) while watching. I've been a long time sub on your channel. Can I ask your age? How old are you? Thanks again and cheers from Norway. 👍🏽
@SardarTariqMahmood
3 жыл бұрын
kzread.info/dash/bejne/k6Nqo5lylJTAh9Y.html ,
love your new camera. great video
1:42 a drawing without the centerlines hurt
@enricorossi5996
3 жыл бұрын
Especially see the holes drew without a partial section.
@11:51 that wet/oil stone! I need one of those! Well, I WANT one! Keith Rucker has restored a few...
@ronaldhorne5106
3 жыл бұрын
They still sell them new. Norton 3 stone IM-313 @ $200 ea., three stones, holder with top, and a pint of Norton honing oil.
On the shaft part I was wondering how you held the +- .010 length. I can do it but it takes a bit of a effort.
Had a little chuckle at the pronunciation of Waunakee, should be more like "wahnah key". There's tons of fun videos on youtube of people attempting to pronounce Wisconsin cities. :)
@gregseales3943
3 жыл бұрын
I live in Pewaukee WI and yes many hard to pronounce. :-)
@51ubetcha
3 жыл бұрын
I wonder how they would pronounce Oconomowoc, Menomonee Falls, Waukesha, etc.😊
Looks great Adam thanks for sharing with us. Adam, have you ever done a video of making a cast iron skillet or dutch oven smooth inside to get rid of the pitting from the mold when the casting is done? Thought I had seen one once but was unable to find it in your videos. Fred. 🙏🏻🙏🏻👍👍👏🏻👏🏻👋👋
@SardarTariqMahmood
3 жыл бұрын
kzread.info/dash/bejne/k6Nqo5lylJTAh9Y.html ,
Thanks Adam
Muito bom com sempre trabalho com precisão! Abraço do Brasil!
Can you give a heads up on the HY-PRO spiral flute tap set? Looked at all my local suppliers & not one carries HY-PRO in a set like the one at 19:30 point of the video. Just let me know where I can get a set exactly like those. Thanks & very good video.
@tomt9543
3 жыл бұрын
Amazon, MSC, Fastenal...... Google is a wonderful thing!
@robertginther9248
3 жыл бұрын
@@tomt9543 Tried Google, Amazon, Msc.; none of them have that exact set. If you find them, can you send me a link? I want that exact set. Thanks, Bob Ginther BAE.
GREAT JOB, GREAT VIDEO, [ BACK TO WORK ]...
Hey Adam!! Loving the content, esp you and Abby’s trips. Was wondering how to get in touch with you to see if you would be interested in making some square thread lead screws. Let me know!! Thanks brother!
What about the key ways in the drawing? Did I miss that?
@lukamadunic8534
3 жыл бұрын
There is no key way in the drawing. It is threaded hole. Drawing is not very good
@Orxenhorf
3 жыл бұрын
Those were the tapped screw holes in the ends showing through.
I need more Fireball Tools stuff 👍👍
Can't say I'm a machinist but when someone says somewhere around that "measurement" I know it will be smack in the middle of what they asked. Probably a pro tip for you when you ask for a job to be done.
I would have put 3-4 of those blocks in at a time and probably messed them up.
1st .. well i'll be.. another SNS excellent! hope your va cay went well !
Those gussets look more like plasma cut than waterjet cut... ?
Nice work.
Wonder how the tools feel about cutting through the plastic in the second job. "Wow, that was easy .. didn't hardly give up a fight at all." "Yeah, I drilled through those blocks fast. Are we getting sharper, or was that an easy job?" :) Thanks Adam, great work as always.
I bought a tap from an aircraft surplus and it was marked 10x32 but man that was a big #10 to me. Naturally it was a Metric 10 but with 32 threads. Strange.
@SardarTariqMahmood
3 жыл бұрын
kzread.info/dash/bejne/k6Nqo5lylJTAh9Y.html ,
@samuraidriver4x4
3 жыл бұрын
You sure it wasnt 33.87 tpi? M10x0.75 is pretty standard metric fine thread and works out to 33.87tpi.
@perrylocke6037
3 жыл бұрын
It is a 10-32 helicoil tap. So it makes a 10-32 that is about .050 bigger and a helicoil insert is inserted and a perfect 10-32 is inside.
waunakee - won a key
It doesn't matter at all, but if you're trying to pronounce Waunakee, it's pronounced similarly to "want a key." Satisfying video as always. ;)
@rossfudd256
3 жыл бұрын
Without the t. "wan a key", but good try to Adam, a lot of people pronounce it that way when they first see it.
I hope you are well compensated by your friends for these projects. They get a professional product and should pay that. Enjoy the videos
@SardarTariqMahmood
3 жыл бұрын
kzread.info/dash/bejne/k6Nqo5lylJTAh9Y.html ,
@millomweb
3 жыл бұрын
The comment: "I had him make some parts for the steering racks on some Porsches that I have and they were exact, spot-on, to what I was hoping for. I was amazed at the quality of the work! The price was very fair as well." suggests he charges a fair price.
Ooh didn't realise you took on viewer jobs, how much do you charge?
Thank you very much for the nice video. Stay Safe and healthy.
In other news, Rocket Lab faces its second launch failure in less than a year...
@rodney2294
3 жыл бұрын
Yeah not a good look!
@abom hey how can i get a hold of you i have a small project its a part for my father in law hes not able to do much anymore but loves his tractor and i needs a pump shaft any way you could help ? I know your busy much love
The print shows a key way slot. Was it not needed or did I miss something?
@charliepolen
3 жыл бұрын
The features you seeing are the tapped holes. The drawing shows hidden lines.
@easternwoods4378
3 жыл бұрын
Just drill and tap both ends. But it does look like a keyway
@johnlennon335
3 жыл бұрын
It looked like a key way but it was the detail of the tapped hole in cross-section view.
@howardmerrill1969
3 жыл бұрын
@@charliepolenOk I see that now thanks.
Aaah yes, big rock candy mountain, good ol' Crackmaster-Carr.. Almost as bad as the homeless despot. Almost.
Who you callin an acetal?
Why did one piece fit tighter than the other when they were milled at 3/4" in the same operation?
@chrisnorth3458
3 жыл бұрын
burr on hole or shaft, tolerance on the diameter of the shaft, wear on the lower part of the end mill
I'd like to see you make a custom machine that you will use.
How do you set pay scale for odd jobs ?