Snowmobile carburetor symptoms and tuning. Sled carbs.

Автокөліктер мен көлік құралдары

Snowmobile carburetors can be tricky? Idle screws and needle jets. Pilot jet plugged? Needle and seat? Carbs can be tricky because the slightest little thing can throw the whole sled out of whack. Ricki takes us through some of the possible symptoms and how to fix them. Most carburetors just need a good cleaning to get that old sled running like a top but knowing what to clean is half the battle. Whether it's at idling or wide open, Ricko explains. GO TO: WWW.DIGIT9.CA
If you're new to our channel, we post videos about snowmobile tuning. Lots of tips and tricks for maintaining and modifying your sled and sled trailer. Mostly just DIY sled stuff for people who like to get their hands dirty or tinker in their garage.
Subscribe to our channel right here: kzread.info?sub_c...
www.digit9.ca
/ digit9sledders
DISCLAIMER: We don't recommend trying anything you see on this channel without contacting your manufacturer or certified sled technician.

Пікірлер: 299

  • @mykolastess2107
    @mykolastess21073 жыл бұрын

    Looks like we’re going to digit 8.0 soon lol

  • @stackzoverheaddoors454
    @stackzoverheaddoors4543 жыл бұрын

    I just bought my first sled a 98 cougar with 2800 miles on it and been sitting for 5 years and your videos lately have been very helpful

  • @DIGIT9

    @DIGIT9

    3 жыл бұрын

    Thx for tuning in ! Glad we can help

  • @trumps-a-hoe
    @trumps-a-hoe3 жыл бұрын

    I've loved 2 strokes my whole life. Been building and tinkering for years but the carburetor was always like a foreign language. I picked up an off road go kart and put the motor off an indy sport 440 on it and thanks to your video I'm able to properly tune the carbs and haul ass. Thanks for breaking down where and how to tune the carb all the way around and not just the fuel/air mixture lol

  • @snowmobile333
    @snowmobile333 Жыл бұрын

    Thank you so much, I am currently working on tuning my 97 polaris indy 500 carb and this was helpful

  • @canadaeast8358
    @canadaeast83583 жыл бұрын

    What a sound your sled got she’s a beast. Good video man

  • @R3D_R41D3R
    @R3D_R41D3R3 жыл бұрын

    Thanks man another vid with good info exactly what I needed to know to fix some bottom end bog

  • @Kwobler
    @Kwobler Жыл бұрын

    Purchased a 600rs trail converted but now i understand why it runs the way it does. And many things i can look at and try now.

  • @gage_g_0250
    @gage_g_0250 Жыл бұрын

    This was so helpful, its been a bit since I've done some work on a snowmobile, let alone owned and rode one. Got myself a 1997 Ultra, didn't hold idle but I got it running and fairly close to being back together. Idles at about 3500 and slowly dies down to a little under 3000, so I think I just gotta turn the air fuel screw out a half turn. Seems to be running lean.

  • @danielschabilion9435

    @danielschabilion9435

    7 ай бұрын

    Should idle

  • @jeffgoodreau694
    @jeffgoodreau6942 жыл бұрын

    Great video, thank you sir

  • @John-fz8uo
    @John-fz8uo2 жыл бұрын

    Working on my first sled. 1985 Polaris Indy Trail 440. I know nothing about motors, so I watched a vid. When I took my carbs apart yesterday, they were caked in hard white stuff. I couldn't even get it all off. I pulled an impressive amount of grass and acorns out of the air box also 😄 still can't get it to start without pouring pre-mix into the spark plug holes. I'm counting on you - subscribing now

  • @DIGIT9

    @DIGIT9

    2 жыл бұрын

    Diaphragms in your fuel pump are probably sticking , dried out ? Get someone to plug the suction side of carbs when you try to start it ! Did you clean pilot jets ?

  • @John-fz8uo

    @John-fz8uo

    2 жыл бұрын

    I'm going to take it apart and do it again because I'm not happy with how I cleaned any of it and I'll do what you recommended. The white stuff in the carbs was/is absolutely baked on and lumpy and I shouldn't have even put it back together. Is a wire brush best to use? Can I let it soak in something?

  • @DIGIT9

    @DIGIT9

    2 жыл бұрын

    Tooth brush and WD 40 works good to get the white shit off , can use a brass wire brush too ! Then brakecleaner to get the rest off ! Still need to pull pilot jet and clean good or replace with new !!

  • @John-fz8uo

    @John-fz8uo

    2 жыл бұрын

    @@DIGIT9 Bought a new fuel pump, the WD40 with the brass brush is best so far. I cleaned the nozzle in each carb, I didn't know it was even there last time - they were that dirty. Just need to clean pilot jet. I noticed that the C clip on both my brass pins were set on the top, so I moved them to the middle. That's all I've done so far today. I would like to empty and clean the gas tank also...then see if she starts?

  • @John-fz8uo

    @John-fz8uo

    2 жыл бұрын

    @@DIGIT9 Well, I had the '85 out for a ride in the yard today, Sir! I'm not 100percent done - it stalls out if I don't keep giving it gas. But, it starts again on the first 2 pulls without me having to dump some fuel into the spark plug holes like I used to. I should focus on the screws on the carbs now?

  • @matthewenerson2095
    @matthewenerson20953 жыл бұрын

    Been building Rmks since 96 before Polaris even made a Rmk. First was the 96 Ultra with a 1 1/2 136😅. Great content! Wish you guys were in the states would love to have a beer eh!!

  • @DIGIT9

    @DIGIT9

    3 жыл бұрын

    Did you say beer!!!!!! We're in.

  • @carsontitford2659

    @carsontitford2659

    3 жыл бұрын

    Was that with the bolt on plastic paddles?

  • @dysfunctionalee3395
    @dysfunctionalee33954 ай бұрын

    Hey my friend great video my problem is with my 1992 arctic cat wildcat, it has the black magic pipes, it runs amazing in -20 but the minute the weather warms up and it’s only -3 snowmobile is Boggie and doesn’t have enough power to take off. Do I have to take the carburetter apart to put a different jet in or do I just adjust the setscrew

  • @triplehelper6944
    @triplehelper6944 Жыл бұрын

    New pickup filter and line. Hose from pump to block is clear and I can blow air through it. Thanks for the ideas.

  • @DIGIT9

    @DIGIT9

    Жыл бұрын

    Check the needle and seat in carb , might be stuck shut , not allowing fuel into float bowl ?

  • @curthazlett595
    @curthazlett5953 жыл бұрын

    My cousins boosted 670 carbs had super worn slide bores so worn it was wild

  • @thatmodshop7160
    @thatmodshop71603 жыл бұрын

    Digital 8.5 lol good video well explained!

  • @zakksrage
    @zakksrage3 жыл бұрын

    That’s a sweet sled stand

  • @chadstenback1221
    @chadstenback12213 жыл бұрын

    Sure miss the days of the triples, such a distinct sound:)

  • @carsontitford2659

    @carsontitford2659

    3 жыл бұрын

    The good ole days of ultras, storms, Mach z, t cats and zrt’s 👌🏽👌🏽

  • @olleahlnas299
    @olleahlnas299 Жыл бұрын

    I tried for long now to get my -1975 Aktiv 600 with rotax 503 to run better, it only runs on 1/2 to full throttle, no idle, swapped the carb to a new mikuni (before it was tillotson) and it runs better but not good. Any ideas? Greetings from Sweden🇸🇪

  • @terryroberts2357
    @terryroberts23572 жыл бұрын

    i have a 98 artic cat 340 that won`t start unless i prime it by taking plugs out and giving it a shot of mixed gas . when its running it seems fine but as soon as it stops cant get it to start even if its warmed up

  • @tom-ehill2713
    @tom-ehill27136 ай бұрын

    Just had this 86 Yammi 540 Xlv carb super soaked! Sat up three years. Right ski froze tight. Fixed! Still runs hesitant off no choke! Have to gun it actually! New parts wont work. Jet seat is metal. Newer sleds are neoprene now😢

  • @walterw4770
    @walterw47703 жыл бұрын

    Very impressed by the video. I'm tempted to do a carb cleaning myself. I have taken my 1994 indy 500 in now a few times, and the 1 carb keeps flooding. He told me the last time that he replaced the needles. Any suggestions what I should try next?

  • @danraby4344

    @danraby4344

    3 жыл бұрын

    Sounds like you need a float adjustment

  • @DIGIT9

    @DIGIT9

    3 жыл бұрын

    something may be wrong with needle and seat !

  • @cjnedeau3338

    @cjnedeau3338

    Жыл бұрын

    @@danraby4344 Polaris don’t have float height adjustment

  • @nicholasbrehm7838
    @nicholasbrehm78382 жыл бұрын

    I am perplexed by my Sled. Carbs are new and look perfect, float set correctly, float needle cleaned and checked. Doesn't leak when parked or pulled with kill switch on. Two things I did. I used a smaller fuel line from tank to fuel pump (used 1/4" vs 3/8" stock). Also up'd vaccum line size from case to fuel pump. Do you think that would be enough to increase pressure to the carb when running to force fuel past the float needle?

  • @DIGIT9

    @DIGIT9

    2 жыл бұрын

    No ! Not sure what your problem is , not enough info ! Whats it doing or not doing ?

  • @wtfbuddy1
    @wtfbuddy13 жыл бұрын

    Nice video - out west you must have a different meaning for SMEGMA in your carb, but yes clean it out lol. Cheers

  • @monotheis6889
    @monotheis6889 Жыл бұрын

    I'd really like to get a closer look at that stand she was up on, so I could build one myself for my dad.

  • @DIGIT9

    @DIGIT9

    Жыл бұрын

    Now adays , almost cheaper to buy one ? Princess Auto, Amazon ?

  • @Smackvttv
    @Smackvttv3 жыл бұрын

    Digit 8 channel coming soon

  • @DIGIT9

    @DIGIT9

    3 жыл бұрын

    LOLOLOLOLOLOL......it was very close to Digit8! That's funny man.

  • @gerardjones7881
    @gerardjones78813 жыл бұрын

    the pilot jet you held at the 30 second mark, is it supposed to be clear from end to end too.? Seems a silly question but I'm doing a new to me mikumi carb on an old abused skidoo and theres no light coming through, wire will not pass end to end. I believe that pilot jet is also known as an emulsion tube, the fine holes atomise the air fuel mix. Also, theres 2 adjustable jets on the outside, small one is idle mix ?, it was 1 1/2 turns out. But theres a larger one and it was 3 1/2 turns out, that seems a lot. This is my first sled, I got a real klunker but it was very cheap, guy said it used to run good but now will not stay running. Bowl had grit and little bits of crap and varnish. I run it through a hot ultrasound bath, sprayed with carb cleaner, ran wire through every orifice and blew it out with air. Its ready to go back in, just curious about that adjustable jet, it has knurling so its obviously meant to be adjusted without tools.

  • @DIGIT9

    @DIGIT9

    3 жыл бұрын

    Pilot jet yes but if its the one from the float bowl , no !

  • @DEVUNK88
    @DEVUNK882 жыл бұрын

    what is that slender tube next to the pilot jet? It slides into a hole in the bowl? what is its purpose?

  • @louis-philippest-jean2166
    @louis-philippest-jean21663 жыл бұрын

    I have a 1991 Polaris indy 500 l/c, and i’m having a hard Time tuning the carbs. I’ve rebuilt the entire fuel system from the strainer in the tank, fuel pump, both carbs have been toroughly cleaned, rebuilted with kits and sync’ ed, and it Stills starving for fuel from idle to to top end, but if i only adjust the enricher (choke) so it is slighly pulled, it runs like a Champ. I’ve checked both crank seals , They does’nt seem to be bad, but vaporizing brake cleaner around them is not an exact science. I’ve checked compression, 110 on both sides. It is like my 20th sled, bought it to pull the sleigh with the kids around the house and it is by far the sled that give me the most intense headaches 😂. I was thinkin’ about putting 300 mainjets in place of the stock 280’s. i Also have bigger pilots jets to play with.

  • @DIGIT9

    @DIGIT9

    3 жыл бұрын

    try raising the needles

  • @mountaincat2001
    @mountaincat20018 ай бұрын

    Miss seeing you r videos. Can you make a video on carb fuel pump testing please

  • @DIGIT9

    @DIGIT9

    8 ай бұрын

    We will add it to the list ! Thx for the recommendation !

  • @samuellamont8539
    @samuellamont8539 Жыл бұрын

    I have several 3 cylinder snowmobiles. Commonly known to foul a plug or 2 until engine is warmed up. Any tips on syncing 3 carbs. I use a meter that reads the air coming in through the throat of the carb and it helps a ton, but what do you do to really dial them in perfect?

  • @DIGIT9

    @DIGIT9

    Жыл бұрын

    Takes alot of time and a good ear !

  • @JJJ12W
    @JJJ12W2 жыл бұрын

    Question I just rebuilt my carb ( Mikuni VM 34-229) for my Ski Doo Citation 4500 (377 Motor), everything has been replace except the floats and throttle slide. It has new fuel pump, new fuel lines, new intake gaskets, motor has 120 psi both cylinders. new Spark Plugs and wires, good spark. I have not changed the coils or done anything with the points. I had it running after for 10 minutes after lots of tinkering with both the idle and air screw. Then I took it for a 5 minute drive worked great shut it off and loaded it up in the truck unload it in m y garage and now it won't start again. I set everything back to factory settings as per the Citation Manual and I still I can not get to stay run. It will start runs for 10 seconds or less then dies, if you cover the air intake with your hand you can get to run a little longer but as soon as you remove your hand and open the up the throttle it dies. Not sure why it won't staying running, Is it starving for fuel or air? Not sure what I should adjust as everything I have read says put the air screw to the manual setting and leave it alone. Any help or ideas would be great.

  • @DIGIT9

    @DIGIT9

    2 жыл бұрын

    Sounds like fuel problem ! Did you check the pickup screen in the fuel tank ?

  • @brendongreen8008
    @brendongreen8008 Жыл бұрын

    I got a question I have a 1996 polaris indy 500 it don't idle at all

  • @darcy32171
    @darcy32171 Жыл бұрын

    I`m messing with an oldie:1980 El Tigre 6000. Put all new gaskets/seal/pistons/rings in it. Had it running last fall then wouldnt start over winter. I just recently pulled the carbs and soaked them. Everything is spotless, all new fuel lines, filter. Dual Mikuni fuel pump is clean. It only runs on one cylinder. I pulled the float bowl drain on the suspected cylinder and it was bone dry. Where should I start to look? I`m at my wits end with this machine. Thanks.

  • @DIGIT9

    @DIGIT9

    Жыл бұрын

    Needle and seat might be stuck ?

  • @brandonburge9981
    @brandonburge99813 жыл бұрын

    I have a 1998 arctic cat zr 500 and it idles fine but bogs and sputters at around 4000 rpm, the sled is set up to be a drag sled and the clutch don’t engage tell 5000 rpm, I have a fully rebuilt motor and have tryed almost everything I can, any advice would be greatly appreciated, love your videos, that’s a sick sled you got

  • @DIGIT9

    @DIGIT9

    3 жыл бұрын

    Sounds like a lean spot ! Try raising the needle , dropping c-clip !

  • @brandonburge9981

    @brandonburge9981

    3 жыл бұрын

    @@DIGIT9 thank you for the advice, I’ll try giving her more fuel, really appreciate the reply! Have a great day man

  • @dennislorden3142
    @dennislorden31423 жыл бұрын

    I got a jag 440 bogs after holding it wide open for more than about 5 seconds choke seems to help it come out of the bog, I replaced fuel pump cleaned both jets new needle valve bypassed petcock, I’m wondering if it’s maybe the screen in the tank is clogged?

  • @DIGIT9

    @DIGIT9

    3 жыл бұрын

    You got air bubbles in fuel lines ? Ya check filter in tank ! Raise needles in carb !

  • @davidsdetailingco.9635
    @davidsdetailingco.96353 жыл бұрын

    Just a question, on my artic cat jag single carb, there is not change when adjusting the small idle screw and only a small change when adjusting the big one, is the the result of an air leak somewhere else or??

  • @DIGIT9

    @DIGIT9

    3 жыл бұрын

    ya could be ? Dirty Carb ? Crank seal leaking ? carb boot cracked ?

  • @bigrach123
    @bigrach1232 жыл бұрын

    I know this is an old video but I have a 97 polaris 600 triple that I put an epi clutch kit in at the end of last season. Now all of the sudden I'm not running past 7500 rpm, whereas I was getting up to about 8300 last year. Should I be adjusting my carbs?

  • @DIGIT9

    @DIGIT9

    2 жыл бұрын

    Did it ever run 8300 with the EPI kit ? If not put your old kit back in and try it !

  • @markjordan9357
    @markjordan9357 Жыл бұрын

    How do you clean the main jets on the carb you pictured. My 1992 wildcat 700 is running not very smooth this year.

  • @DIGIT9

    @DIGIT9

    Жыл бұрын

    We have vids that explain the procedure !

  • @Brownie79
    @Brownie793 жыл бұрын

    Ok I got one for ya. I was given a 96 Polaris XLT RMK. It sat for long time I pulled carbs ultrasonic cleaned em. Ran awesome. So I found some pipes for it Pro 5 pipes no silencer so I just straight piped it. I put 190 jets in it and 480Q0 needle jets. Deleted oil injecton Mix my own oil 40:1 gutted air box. Low altitude 4k runs like a bat out of hell. Higher like 6500-8000k at 20F idels great, boggey low rpm have to choke it to get past it then it screams. Dropped needle clip one still same.It has ACCS. Ideas??

  • @DIGIT9

    @DIGIT9

    3 жыл бұрын

    smaller pilot jet , more air screw

  • @Mogachaffe
    @Mogachaffe3 жыл бұрын

    how often have replaced your needles, jet tubes on your snowmobiles over the years? Ive never replaced mine just cleaned them thoroughly 2x a year typically. ive always wondered if i would notice a tuning difference or butt dyno on my sled if i fully rebuilt my carbs.

  • @DIGIT9

    @DIGIT9

    3 жыл бұрын

    Every 5 yrs or so ! I like my sled to run top notch ALL THE TIME !!

  • @Mogachaffe

    @Mogachaffe

    3 жыл бұрын

    Yea you sure do. Been following ya for a few years and watching you pull the plugs out after a long pull and think, wow he’s running on the edge but probably has a pretty good idea how close he can get without melting down.

  • @kapptinhook
    @kapptinhook3 жыл бұрын

    I just got a Polaris Indy 600 sled triple. I think it's an 87 LOL going to pull the carpet apart make sure they're all clean. Apparently the engine was just redone been sitting outside for a couple years. Any suggestions on where to get parts BC Canada. Thanks bro

  • @DIGIT9

    @DIGIT9

    3 жыл бұрын

    Rec Supply , saskatoon sk

  • @northernstoner962
    @northernstoner9622 жыл бұрын

    I have a 2001 or 2004 Yamaha sxr 500 runs perfectly fine but if it drops like 10 degrees it doesn't want to start and it sometimes has a issue of blowing spark plugs when going over half throttle trying to figure it out but kinda stumped

  • @DIGIT9

    @DIGIT9

    2 жыл бұрын

    Clean carbs , pilot jet may be plugging ? Change fuel filters too !

  • @KadenBakerr
    @KadenBakerr3 жыл бұрын

    Hey there,I recently bought a doo 600rs,problem is it idles very high around 5500rpm wondering what could be causing this issue?

  • @DIGIT9

    @DIGIT9

    3 жыл бұрын

    What yr ? Carbureted ? EFI ?

  • @user-ib4lw1bi5x
    @user-ib4lw1bi5x3 ай бұрын

    What could be going on with my carb if I’m losing top end power it runs great to about 20 miles and hr and then nothing it like Boggs

  • @jaymrunner1155
    @jaymrunner11553 жыл бұрын

    hey bud !!! I have a Mountain Magic ski-doo summit x! any idea where to find specs on CPC carb and Paragone clutch??

  • @DIGIT9

    @DIGIT9

    3 жыл бұрын

    Well CPC is still in business , give them a call on the carbs , Paragons are tricky, call Ken at Mtn Magic , 780-266-7477

  • @jaymrunner1155

    @jaymrunner1155

    3 жыл бұрын

    @@DIGIT9 sounds good thank you for the info👍👍

  • @joeswartzack2350
    @joeswartzack23502 жыл бұрын

    I have a 96 bearcat 340 FC. Rebuilt carb, new fuel pump , lines, gas and plugs. It starts, goes like a rocket but will not idle. It seems the air screw has almost no effect when adjusting. The idle screw is wound all the way in for it to try to idle...but I still have to feather the throttle to keep it from quiting when the sled is stopped. Any ideas?

  • @DIGIT9

    @DIGIT9

    2 жыл бұрын

    Does it have reeds ? Cracked or broken ! Or pilot jet plugged

  • @ricklauragessler4508
    @ricklauragessler45082 жыл бұрын

    How do you fix throttle hang? I’m tuning a 2001 XCR800 and the idle loves to hang around 2500-3000 after it revs.

  • @DIGIT9

    @DIGIT9

    2 жыл бұрын

    Check that slides are not damaged , check and lube throttle cable ! Also , check crank seals and carb boots ! Could be suckin air !

  • @willycoolman6432
    @willycoolman64323 жыл бұрын

    Best way to tune idle? I have an 07 rmk 600 ho and I've been working on getting the carbs set up. Last guy had it set for high elevation so I had to return it to my settings for 0-2000ft. I get reading plugs for mid and full throttle but I'm in the dark a bit on idle tuning. BTW these carbs on my sled have a idle fuel screw not an idle air screw. Any help is appreciated.

  • @DIGIT9

    @DIGIT9

    3 жыл бұрын

    Are carbs sync’d ? Sometimes those slides crack causing issues !

  • @willycoolman6432

    @willycoolman6432

    3 жыл бұрын

    @@DIGIT9 I guess I mean off the crack not necessarily idle rpm. Ill check the carbs out next time I have em out but the idle chills out right around 1650-1750 rpm with no idle swings or hang. I just want to know the best way to adjust the idle mixture to make sure I'm not too lean or rich and for good response. A tuning video series might be awesome I'm sure there are a Lotta guys out there like me.

  • @DIGIT9

    @DIGIT9

    3 жыл бұрын

    Then Adjust fuel screw till it works good !

  • @nathanhobbs9334
    @nathanhobbs93342 жыл бұрын

    I have a 1996 skidoo skandic 380. I cleaned the carburetors put a new fuel pump on. It idles fine and mid-range. No top-end unless you pull the choke. Advice?

  • @DIGIT9

    @DIGIT9

    2 жыл бұрын

    Do a plug test ! Should tell you if its lean or fat ! Hold wide open for 5 secs , hit kill button , roll to stop and check plugs ! Im guessing you are lean ? Bigger main jet ?

  • @31viper1
    @31viper1 Жыл бұрын

    Of a 1992 grand touring formula 583 just cleaned the carbs in it and it starts up but it seems like it's flooding itself when it take sprag plugs out I'm just wondering is there anything I'm doing wrong and when I drive the square plugs put them back in and fires backup runs soon as you give the toddler it's bugging up I just want to know if there's anything I can do to fix that

  • @DIGIT9

    @DIGIT9

    Жыл бұрын

    Drop the needles one

  • @danielreehoff9598
    @danielreehoff95983 жыл бұрын

    Great video. I just totally rebuilt the carbs on my 02 polaris exsp- now my clutch side cylinder isnt getting fuel. I have spark but no gas. Any suggestions what i did wrong on rebuild of carbs?? (I rebuilt with carb kit and everything seemed spotless and perfect on rebuild.)thx!

  • @DIGIT9

    @DIGIT9

    3 жыл бұрын

    Needle and seat might not be letting fuel into carb ?

  • @danielreehoff9598

    @danielreehoff9598

    3 жыл бұрын

    anyway to test that off the sled? visual inspection all looks good. thx

  • @DIGIT9

    @DIGIT9

    3 жыл бұрын

    @@danielreehoff9598 any fuel in gas line to carb ?

  • @danielreehoff9598

    @danielreehoff9598

    3 жыл бұрын

    @@DIGIT9 yes fuel to carbs. one line feeds both.

  • @DIGIT9

    @DIGIT9

    3 жыл бұрын

    Gonna have to take carb apart and redo !

  • @aidencourneyea6434
    @aidencourneyea64343 жыл бұрын

    I have a 1997 mxz 670 and I want to run a jaws pipe what jetting do you recommend

  • @DIGIT9

    @DIGIT9

    3 жыл бұрын

    depends on how tight they are and where you are riding , but prob 2-3 sizes over stock

  • @daveg2199
    @daveg21992 жыл бұрын

    Hey Ricki Happy New Year!! 🎆 I’m having trouble with my 99 Indy 500 carbs. They are both clean as a whistle everything stock Chokes are set correctly 3/4 out on air screws Slide bottom out at 7/32 Idle screws at 1/4 Both slides have wear spots from screw I used drill bits to set. All New fuel lines New plugs When Ice cold it starts on 3rd pull but I have to immediately start fiddling with the choke and the throttle to keep it from dying, for a few seconds, then it will idle off choke but high around 3000. Once we’re off and running it’s sharp and fast but when I stop it’s idling still very high around 2500 to 2800. Then if I shut it off hot for even 30 seconds to a minute it won’t start without choke and multiple pulls Plus wide-open throttle and throttle pumping to get it to start. Then once it’s idling hot When I hit the throttle it bogs completely out Unless I pump the throttle To keep it from bogging out then I can run Out of the hole and it’s fine again back to fast and high idle. Not looking for a race just a reliable family sled. Please let me know what you think. Thank you.

  • @DIGIT9

    @DIGIT9

    2 жыл бұрын

    Try 1.5 turns out on air screw

  • @DIGIT9

    @DIGIT9

    2 жыл бұрын

    Your slides may be set too high still ? At WOT , slide should have 1/8 -1/4" of play !

  • @daveg2199

    @daveg2199

    2 жыл бұрын

    @@DIGIT9 thank you I’ll try that! Out in the shop today👍🏼

  • @DIGIT9

    @DIGIT9

    2 жыл бұрын

    Ya , almost sounds lean , drop slides a bit with idle screw first then try air screws

  • @daveg2199

    @daveg2199

    2 жыл бұрын

    @@DIGIT9 ok will do!

  • @torrianoblossey1185
    @torrianoblossey1185 Жыл бұрын

    I have 600 triple xlt my third carb slide won't come all the way done so I can re tune them im bottomed out in the throttle cable screw on idle screw backed all way off and slide still not all the way down any suggestions?

  • @DIGIT9

    @DIGIT9

    Жыл бұрын

    Check the throttle cable box or the slide itself , where cable goes into slide ! Something is getting hung up !

  • @isaacbeauchamp9038
    @isaacbeauchamp90383 жыл бұрын

    Do i have to tune my fuel to air mix if i use a ggb can, cause my sled sputters at WOT, but is fine when i use stock silencer

  • @DIGIT9

    @DIGIT9

    3 жыл бұрын

    Not a big fan of the GGB cans ! Call them and find out ?

  • @isaacbeauchamp9038

    @isaacbeauchamp9038

    3 жыл бұрын

    Thanks

  • @petergrzela8691
    @petergrzela86913 жыл бұрын

    Got a 97 mountain max 700 and runs pretty damn well but would like it to be perfect ;) some days it’s extremely hard starting especially not being ran for a couple of days but will start right up next morning one pull in the cold after being ran the day before, and fouls plugs like crazy I’m not to familiar with tripples but I’ll burn just around a tank of oil to a tank of gas on it not sure if any of this is normal or not since I’m much more familiar with older twins

  • @petergrzela8691

    @petergrzela8691

    3 жыл бұрын

    Also doesn’t want to idle have the idle set to around 2000- 1800 rpm which is probably high but only way I can get it to idle

  • @danielschabilion9435

    @danielschabilion9435

    7 ай бұрын

    Nah that’s about right

  • @skostro100
    @skostro1002 жыл бұрын

    Lost my air box. Can I put a air cleaner on her. Would it work or will I need some major adjustments? Been running with nothing on carb. So far no problems, but I know it won’t continue.

  • @DIGIT9

    @DIGIT9

    2 жыл бұрын

    They make snow filters for that ! Reg air cleaner will make it run fat and boggy !

  • @triplehelper6944
    @triplehelper6944 Жыл бұрын

    Got a 89 Polaris sport 340. It won’t start unless I use wd-40 in carb. New pickup line and new fuel pump. Clean carbs. Runs great once is starts with help. What’s the top 3 things u would check

  • @DIGIT9

    @DIGIT9

    Жыл бұрын

    First , check the pickup/filter in the fuel tank , then check hose from engine block to fuel pump , make sure all hose connections are tight !

  • @DIGIT9

    @DIGIT9

    Жыл бұрын

    If it idles and runs after you use WD-40 to get it going then you have a pilot jet , air screw issue ?

  • @DIGIT9

    @DIGIT9

    Жыл бұрын

    Also check needle and seat , might be stuck ? Choke may need to be adjusted too ? When sled is running , pull choke lever half way , if sled starts to idle down , then choke is good !

  • @nathanburroughs2646
    @nathanburroughs2646 Жыл бұрын

    Nice cut up hand aye 😂🤙

  • @stevebean3512
    @stevebean3512 Жыл бұрын

    77 jag 2000, runs good but seems a bit boggy off the start . Not sure if its tunning rich or something else

  • @DIGIT9

    @DIGIT9

    Жыл бұрын

    Try clutching !

  • @Nte-wn3sp
    @Nte-wn3sp Жыл бұрын

    I dont know if you will awnser since the videos been up for a year but my 1998 skidoo formula 500 will idle fine and go fine but when im going up hill,in deep ish snow, or have someone on with me it will bog down and not want to move but if when i let it idle for about 20 seconds she will have her power again until i do one of the things again

  • @DIGIT9

    @DIGIT9

    Жыл бұрын

    Clutchs need to be cleaned and new springs put in primary and secondary, new belt is a good idea too !

  • @Nte-wn3sp

    @Nte-wn3sp

    Жыл бұрын

    @@DIGIT9 ok thanks

  • @gavincdog2999
    @gavincdog29993 жыл бұрын

    Thanks man i am getting a hat i am exited.

  • @DIGIT9

    @DIGIT9

    3 жыл бұрын

    BOOYAH!

  • @nikolutkauskas5126
    @nikolutkauskas51263 жыл бұрын

    Any ideas why I’m getting horrible gas mileage when I’m supposed to get 20+ easily? 1983 John Deere trailfire that I’m restoring

  • @DIGIT9

    @DIGIT9

    3 жыл бұрын

    no such thing as good gas mileage in a vintage sled !! period !!

  • @trevorhenry7056
    @trevorhenry70563 жыл бұрын

    I’ve got a 97 vmax 600 twin with twin pipes. Has a bog at 40 mph then when you hit the throttle it’ll bog for a good couple seconds then take off like a raped ape. Jetting up 1 size and needle in the .5 position. Been running that way for a couple thousand miles. What do you think could be the issue?

  • @stevechristiansen9037

    @stevechristiansen9037

    2 жыл бұрын

    If it has choke plungers check the bottoms for indents if they are indented (you will see a ring ) replace them because they are not getting a good deal and are allowing gas to pass through or your needle and seat is gummed up and not allowing enough gas to go pass through to keep up with your engine at high RPM

  • @jamiebouchard9862
    @jamiebouchard98623 жыл бұрын

    Will I need to retune my 96 formula 3 if I change from an air box to pod filters?

  • @nathanorchard4705

    @nathanorchard4705

    3 жыл бұрын

    You probably should due to the increase of air flow your new pod filters will give you.

  • @DIGIT9

    @DIGIT9

    3 жыл бұрын

    Absolutely !!

  • @DIGIT9

    @DIGIT9

    3 жыл бұрын

    Pods are not a great idea if your lake running !

  • @jamiebouchard9862

    @jamiebouchard9862

    3 жыл бұрын

    @@DIGIT9 I’ve got the air box and it’s all together. The sled sat with gas for 6yrs and the carbs were the worst I’ve ever seen. Slides were corroded to the bottom of the carb and all the jets were corroded shut. I cleaned em and got it going but it seems to be weak on the center cylinder. At idle u can hear the pipe loading up and it begins to foul the plug. Bought a harbor freight compression tester. 40psi in all 3. Junk. Bought the $39 compression tester at oriellies and it’s 90psi around. This weekend I’m going back to buy the $49 tester cause I know it’s better than 90psi. Plus, it seems the 3 wouldn’t be exact if I had a low compression issue. Chances seem unlikely that all 3 have dropped to exactly 90

  • @DIGIT9

    @DIGIT9

    3 жыл бұрын

    Might have to clean carbs a few times to get all the shit out of them ?

  • @pablosixtyseven5028
    @pablosixtyseven50282 жыл бұрын

    hi rick, are you going for digit 8? or 7 ?

  • @DIGIT9

    @DIGIT9

    2 жыл бұрын

    I'll stay at 9 , thx !

  • @josephgillespie6108
    @josephgillespie61082 жыл бұрын

    I got an arctic cat 550 out of a 1998 panther and I put it in a fourwheeler but For some reason it idles perfectly but when I give it any throttle it bogs way down and just before it dies if I hit the choke it comes alive again. It’s stock besides a 2.5 degree timing key and I’m 99% sure it’s the carbs but don’t know enough about how to tune them. Thoughts?

  • @DIGIT9

    @DIGIT9

    2 жыл бұрын

    Take the timing key out of it !

  • @josephgillespie6108

    @josephgillespie6108

    2 жыл бұрын

    @@DIGIT9 it was the same before I put the key in

  • @DIGIT9

    @DIGIT9

    2 жыл бұрын

    You forgot to mention that ! Have you cleaned carbs lately ?

  • @josephgillespie6108

    @josephgillespie6108

    2 жыл бұрын

    @@DIGIT9 yeah I think I found my problem though one of my choke plungers is probably 2mm lower then the other one

  • @DIGIT9

    @DIGIT9

    2 жыл бұрын

    That doesnt help !!

  • @kenknutson4684
    @kenknutson46845 ай бұрын

    Great video! I know this is an older video and not sure if you're up reading comments but I have a 1995 Arctic Cat Puma w a 340 in it. When I started it up this winter it would run for a bit then die. I would have to hold the throttle wide open to get it to run and if I let off on the throttle it would die. It keeps on flooding. I've cleaned and replaced all the parts in the carb, new fuel pump, fuel filter, cleaned the tank and put new plugs in. I've adjusted the new choke to 1/8" when pulled up. Air screw is 1 - 1 1/2 times out and idle screw is about the same. I'm perplexed??!! Any thoughts?

  • @DIGIT9

    @DIGIT9

    5 ай бұрын

    Did you clean or replace the pilot jet ?

  • @kenknutson4684

    @kenknutson4684

    5 ай бұрын

    Yup. Cleaned it first then replaced it. Same result both times. Flooding

  • @DIGIT9

    @DIGIT9

    5 ай бұрын

    Needle clip in middle location ? Almost sounds like your needle is stuck ?

  • @DIGIT9

    @DIGIT9

    5 ай бұрын

    Your choke may be stuck open too ?

  • @DIGIT9

    @DIGIT9

    5 ай бұрын

    Are you sure its flooding or running out of fuel ?

  • @lewismartin7037
    @lewismartin70376 ай бұрын

    How do you know how far open the slides are supposed to be when down against the stop screws.

  • @DIGIT9

    @DIGIT9

    6 ай бұрын

    Slides should be 1/8-1/4 " from top cover when wide open !

  • @lewismartin7037

    @lewismartin7037

    6 ай бұрын

    Thanks, what about space when all the way closed?

  • @DIGIT9

    @DIGIT9

    6 ай бұрын

    The idle screw should just touch the slide when all the way down , thats your starting position , then adjust from there !

  • @adamarnold2075
    @adamarnold20753 жыл бұрын

    Where did you get your bar riser setup?

  • @DIGIT9

    @DIGIT9

    3 жыл бұрын

    Custom made !

  • @TeeBagMaster19
    @TeeBagMaster192 жыл бұрын

    I have a 98 XLT, and it bogs at bottom end but screams from mid to top????

  • @DIGIT9

    @DIGIT9

    2 жыл бұрын

    Lots of issues there , air screw could be turned out a bit , new belt , new springs in clutch’s , bad gas ?

  • @trevorcreed2342
    @trevorcreed23423 жыл бұрын

    What can I do fix my sled fouling plugs over and over.

  • @petergrzela8691

    @petergrzela8691

    3 жыл бұрын

    Got the same problem with my 97 mountain max 700

  • @petergrzela8691

    @petergrzela8691

    3 жыл бұрын

    Ik triples are known to foul out plugs but every 100 to 200km or so plugs are shot

  • @DIGIT9

    @DIGIT9

    3 жыл бұрын

    check oil pump , make sure your running the right plugs , check compression

  • @michaelhoobler7520
    @michaelhoobler75203 жыл бұрын

    What about the nylon washer under the. C clip on Needle ??? Is that factory or ad on ?

  • @DIGIT9

    @DIGIT9

    3 жыл бұрын

    Factory

  • @michaelhoobler7520

    @michaelhoobler7520

    3 жыл бұрын

    Do u need them or not really i know it will change the hight some

  • @michaelhoobler7520

    @michaelhoobler7520

    3 жыл бұрын

    Do u need them or not really i know ot will change the hight some??

  • @DIGIT9

    @DIGIT9

    3 жыл бұрын

    Ya keep that washer if you can !

  • @michaelhoobler7520

    @michaelhoobler7520

    3 жыл бұрын

    Thanks ricko u are the man

  • @jeffauger8142
    @jeffauger81422 жыл бұрын

    Hey just cleaned my carb on skidoo and now I’m having problems with the sled reving way high I tried adjusting air idle nothing and my fuel air screw nothing

  • @jeffauger8142

    @jeffauger8142

    2 жыл бұрын

    I checked the floats I don’t think they got stuck… what could be my issue … or what should I adjust, the sled is almost wide open when starting

  • @DIGIT9

    @DIGIT9

    2 жыл бұрын

    What yr sled ? What kind of carbs ? Sounds like your slides are hung up or in backwards !

  • @jeffauger8142

    @jeffauger8142

    2 жыл бұрын

    It is 94 skidoo tundra 300 was a stuck needle wasn’t seating properly , looks like it’s fine now running good “, I do have a question about adjusting to spec what should my air/fuel set screw be at !

  • @DIGIT9

    @DIGIT9

    2 жыл бұрын

    Air screws usually start at 1.5 turns out !

  • @kendalmouritsen5385
    @kendalmouritsen53852 жыл бұрын

    Sorry in advance for this rather long comment but anyways, I have a 1998 Polaris Indy 500 liquid cold and it has a really bad bog on the low end I had the motor board out 20 over on each cylinder rebuilt the top and new pistons new gaskets new rings etc. it has 130 psi compression per cylinder but it still has a bad bog I replace the pilot jet sizes by going one size bigger messed with the choke settings the nut on the top of the carburetor and the main jets did not change those but it still has that bog any suggestions?

  • @DIGIT9

    @DIGIT9

    2 жыл бұрын

    Does it still bog with sled on a stand , back end lifted ?

  • @DIGIT9

    @DIGIT9

    2 жыл бұрын

    What type of gas you running ?

  • @kendalmouritsen5385

    @kendalmouritsen5385

    2 жыл бұрын

    Running 89 with oil mixed In as this is the first tank with the new rebuild

  • @kendalmouritsen5385

    @kendalmouritsen5385

    2 жыл бұрын

    @@DIGIT9 I have not tried that yet

  • @DIGIT9

    @DIGIT9

    2 жыл бұрын

    Check compression when warm , if its below 120 , use 87 octane ! Not sure how much oil you put in tank but that will cause a bog as well ! Have you cleaned clutchs and put new springs in ?

  • @RichardBrown-be3fm
    @RichardBrown-be3fm2 жыл бұрын

    Where do you get the carb air filters? I am having issues finding them.. thank you!

  • @DIGIT9

    @DIGIT9

    2 жыл бұрын

    Last set I got on Amazon !

  • @RichardBrown-be3fm

    @RichardBrown-be3fm

    2 жыл бұрын

    @@DIGIT9 copy. I bought a set on there and they were not at all what they were supposed to be. Must have been just bad luck. I will look again. Thanks for your time..

  • @DIGIT9

    @DIGIT9

    2 жыл бұрын

    Have to double check your measurements , plus check part #s with K & N !

  • @RichardBrown-be3fm

    @RichardBrown-be3fm

    2 жыл бұрын

    @@DIGIT9 understood. Yeah the flange measurement was on. Unfortunately they sent me carburetors that were mushroom shaped instead of fairly parallel and perpendicular to the sled if that makes sense. The farther away they got the bigger the filter was and they hit on each other. But yes, I will do what you said and check it out.

  • @DIGIT9

    @DIGIT9

    2 жыл бұрын

    Think the part # I used was 0800 ?

  • @dirtyfacegeorge9938
    @dirtyfacegeorge99383 жыл бұрын

    I got me a Greasy triple too, 😂

  • @mountaincat2001
    @mountaincat20013 жыл бұрын

    I wanted to be the first one to say thank you

  • @DIGIT9

    @DIGIT9

    3 жыл бұрын

    You're very welcome! Thanks for watching.

  • @THS033
    @THS0332 жыл бұрын

    My sled has a studder in the low end and a bad bog when accelerating, once it gets past about 7000 rpm it takes off like a rocket. It also gets insanely bad fuel mileage. Like 3 km per litre

  • @DIGIT9

    @DIGIT9

    2 жыл бұрын

    Try cleaning clutchs and new springs !

  • @THS033

    @THS033

    2 жыл бұрын

    @@DIGIT9 will do, thanks!

  • @jeremymartin1566
    @jeremymartin15663 жыл бұрын

    Nice video , lol on all finger comments .... Jeremy M

  • @DIGIT9

    @DIGIT9

    3 жыл бұрын

    thx Bud !

  • @williamedwards7315
    @williamedwards73152 жыл бұрын

    For cleaning your pilot Jets one small strand of copper wire

  • @calebcragun6191
    @calebcragun61916 ай бұрын

    I am working on my first snowmobile, and it has a double idle. I am not sure what is causing it. I have cleaned carbs multiple times, There is fuel to the carbs, I have checked for crankcase leaks with starter fluid, The exhaust pipes are clear, (someone before me swapped it for twin pipes) Air box is clean Could it be caused by a very rich(or lean) condition? Thanks!

  • @DIGIT9

    @DIGIT9

    6 ай бұрын

    What is a double idle ?

  • @calebcragun6191

    @calebcragun6191

    6 ай бұрын

    @@DIGIT9 It will idle at 1500 when I start it, if I rev it past 2600 it will idle at 2600. I can get it to come down to 1500 by using the choke. I suppose it could be a hanging idle. It only happens at certain air screw and idle screw mixtures. I was turning the air screw in and a bog off of idle was getting smaller and smaller until it was almost gone, then I decided I wanted it to idle higher, so I turned the idle speed screw in and the double (or hanging) idle came back.

  • @DIGIT9

    @DIGIT9

    6 ай бұрын

    Try raising the needle ! Your starving it now ! Air screw should be 1-1.5 turns out !

  • @calebcragun6191

    @calebcragun6191

    6 ай бұрын

    @@DIGIT9 I'll try raising the needle, I have it in the middle position now because when I took it apart, the e clips were broken. When does the needle come into action? Right when the slide comes up from resting on the bottom of the carb? Thanks!

  • @DIGIT9

    @DIGIT9

    6 ай бұрын

    Needle has affect from 1/8 throttle and up , but also affects idle a bit !

  • @jasonmunguia3219
    @jasonmunguia3219 Жыл бұрын

    My snowmobile bogs down when I give it gas it's a1980 Yamaha exciter 440 runs and idals but bogs down and dies. When I give her gas .

  • @DIGIT9

    @DIGIT9

    Жыл бұрын

    New belt and clutch springs , clean carbs , new plugs , check compression !

  • @davidyonker7224
    @davidyonker72243 жыл бұрын

    I've got a 1993 Polaris Indy XLT with pipes. New to us but don't know any history. Cleaned carbs, new gas. Idels ok with a random backfire. Give it gas and bogs down and backfires. Any suggestions

  • @DIGIT9

    @DIGIT9

    3 жыл бұрын

    also check the safety switch in throttle block

  • @davidyonker7224

    @davidyonker7224

    3 жыл бұрын

    @@DIGIT9 Thanks for all videos. Kind of new to snowmobiles, that's the little button in the thumb throttle correct? It looks like it's functioning. I have a parts sled also so I could swap it to see if there is a change. Some tell me it is running lean and that is causing the backfire. Just putting a list together of things to check. My son is pumped to be working on it with me. #raisinggearheads

  • @DIGIT9

    @DIGIT9

    3 жыл бұрын

    @@davidyonker7224 make sure needles are in the right spot too ! maybe try lifting them to give it more fuel

  • @davidyonker7224

    @davidyonker7224

    3 жыл бұрын

    @@DIGIT9 Great call on the needles, they were set to run as lean as possible. I set them to the middle and now no backfiring at idle. Still back fires at higher rpm's when I let off. It does have pipes on it so should it need a little more gas? Thinking about raising the needles one more notch. Thanks again for all you help.

  • @DIGIT9

    @DIGIT9

    3 жыл бұрын

    Yup more fuel wont hurt !!

  • @Shadowmythx117
    @Shadowmythx1173 жыл бұрын

    Why are they rare? My 2018 has carburetors..

  • @DIGIT9

    @DIGIT9

    3 жыл бұрын

    Parts for older carbs are getting hard to find.

  • @WyoUltra
    @WyoUltra3 жыл бұрын

    I have a video of my sled running "weird" on my channel. I can't seem to figure out the problem. It runs great for a while, then it won't. Jetting is a tad rich (safe side), but the sled will get so boggy it's like it drops a cylinder. But pulling the plug wires proved they are both firing and not dropping off while running weird. Eventually after a while it will clear up and run fine, then run like crap again. if you have a chance I would appreciate your thoughts, otherwise no biggie and thanks for the content! 🍻

  • @DIGIT9

    @DIGIT9

    3 жыл бұрын

    Yr , make , model , fuel type ?

  • @WyoUltra

    @WyoUltra

    3 жыл бұрын

    @@DIGIT9 kzread.info/dash/bejne/hJZrvLGQf6aTcaQ.html 2007 IQR w/ 700 VES motor with slp twins into stingers.

  • @kylebell5129

    @kylebell5129

    3 жыл бұрын

    Love your kids head bouncing around infront of you 👍. Almost sounds like its down into a safety mode. I had an old zrt that would sputter down like that. Spent alot of time going though carbs and so on untill one day I decided to crack the gass cap open, turns out vent on take cap was screwed. I no expert by all means and had run in with bad electrical gremlins that haunted me for seasons on end.. but by the way it sputtered down and shaped backed to life. I'd be also checking to see if there's not somthing going on there after you check that its getting all the fuel it needs. Hopefully there's some guys on here that had some run ins like what you got and guild you in the right direction

  • @DIGIT9

    @DIGIT9

    3 жыл бұрын

    Ya , think you got something electrical going on ? Is hood rubbing on sparkplug tops ?

  • @WyoUltra

    @WyoUltra

    3 жыл бұрын

    @@DIGIT9nope plug caps are on solid. I was going to comb through the harness and double check stuff... Just wanted more opinions on it because it seems kind of unique.

  • @vintagepowersports81
    @vintagepowersports81 Жыл бұрын

    Hi there love your channel could you tell me what you think of this. Carbs are clean it’s getting fuel and air I think it’s a grounding issue or some sort of electrical problem. Let me know if you have ever seen this and what to take a look at. kzread.infoxJVYH1xxopo?feature=share I haven’t dug into it yet haven’t had the time but I do think it’s going to be a cdi or something. I’m used to the older vintage points sleds this is my first newer old liquid cooled machine. Thanks for your advice in advance. Ryan

  • @DIGIT9

    @DIGIT9

    Жыл бұрын

    Sounds like its running out of fuel ! Have you checked fuel filter in tank ? Fuel pump could have crap in it ? Pulse line from fuel pump to crank case could be leaking ? Few things to check ! A cdi wont do what it's doing ! Also check compression !

  • @dk3062
    @dk30622 жыл бұрын

    Shmoo, Shmagma

  • @gerardjones7881
    @gerardjones78817 ай бұрын

    If there's way more to it why didn't you cover it in the video.

  • @DIGIT9

    @DIGIT9

    7 ай бұрын

    Havent got there yet !

  • @mountaincat2001
    @mountaincat20013 жыл бұрын

    Wtf happened to your fingers?

  • @DIGIT9

    @DIGIT9

    3 жыл бұрын

    Upcoming video😉

  • @mudbrats
    @mudbrats3 жыл бұрын

    Digit 6? 🤪

  • @DIGIT9

    @DIGIT9

    3 жыл бұрын

    Darn near Digit8 for sure!

  • @DIGIT9

    @DIGIT9

    3 жыл бұрын

    Digit Dangler ??

  • @collinmckenzie6371
    @collinmckenzie63712 жыл бұрын

    little bit a SHMAGMA lol

  • @dandesjarlais4555
    @dandesjarlais45553 жыл бұрын

    Looks like you put your fingers where they shouldnt be alot ? Ahaha joking!

  • @gordtjs
    @gordtjs Жыл бұрын

    Triples are garbage bruh...lol

  • @mikeharmon8733
    @mikeharmon8733 Жыл бұрын

    DIGIT9.. I get it now. It looks like you are working on DIGIT7? Be good to yourself! Thanks for making the vids!

  • @codyjohnson5674
    @codyjohnson5674 Жыл бұрын

    Digit9 I have a 583 that Boggs from idle to WOT. Is that a needle issue? It idles great and WOT is fine. It's just the initial hit from idle to WOT that's boggy.

  • @DIGIT9

    @DIGIT9

    Жыл бұрын

    Try new clutch springs and a new belt !

  • @Braapcity
    @Braapcity Жыл бұрын

    My first question, what happened to your finger?

  • @DIGIT9

    @DIGIT9

    Жыл бұрын

    Theres a video on that !

Келесі