Motor timing does increase speed. For the Castle motor it is changed through the ESC. I feel like if you would bump it up to about 22 degrees, it would put out numbers very close to if not higher than the Ruddog. The Castle motor was by far the best balanced which will aid in durability.

@niikon

Жыл бұрын

Also, the phase sensors were all absolutely even, meaning the sensor locations on the board are very precise.

@toysforboysrc

Жыл бұрын

Which means less heat when your dialing in your timing..

Thank you for this video! I just picked up two 7700kv motors, not castle but still gives me an idea! I have the ruddog 4.5t in the bin as a backup...

@kgrc0078

4 жыл бұрын

My pleasure! My goal is to be able to help 👍🏼

@fastfordstang13

3 жыл бұрын

I need to make my S22 faster what motor can I use?

@rclunatic

Жыл бұрын

How did the 7700kv hold up

Castle was by far the best these. The vibration and timing variation between the phases speaks for itself...

I have a ruddog 5.0 40 degrees timing on the motor 22 degrees on the esc with a 13.5mm drag racing rotor, ceramic bearings on 2s 23/90 gearing. I'm telling you it's impressive I have taken out quite a few high dollar motors

I'm guessing the Ruddog was louder because of the large cutaways in the side, which probably add some air cooling. Thanks for the test, that was interesting

That castle just sweeps the board

Damn don't know why but I jumped damn near threw my phone when that cable collapsed & the motor sparked 😂 I think I was watching a bit to intensely Ha Ha 🤘🏼 💯

I have a Ruddog 6T and its not loud at all. I think your was maybe vibrating a bit on the analyzer.

nice video bruv I just order myself the same tester.

He said the castle 7700kv! Thing was a beast.

R1: yeah we like to keep our quality motors intact Castle: we can squeeze a bit more without blowing up Ruddog: to Scheisse whith safety, whe like a bit of chaos jah!

@kgrc0078

Жыл бұрын

😂😂

You can adjust the timing making numbers way different . So motors can be faster then out of box .

@kgrc0078

3 жыл бұрын

These were just stock out of the box. But yes 👍🏼

@ptshyu2

3 жыл бұрын

How can I adjust the the r1 with the esc I have it says don’t go above 20

So for amp draw on the castle your amount stated was(way lower) not an actual number. way lower is not a unit of measurement..

Great video, I have the 7700kv castle in my drag car now and it moves. I always tried to get an answer from them about the timing in the motor, but now I have an idea.

@billymartini7723

3 жыл бұрын

What time you running

@Lushiouscorey2011

3 жыл бұрын

@@billymartini7723 I've graduated from the castle system and now have an r1 system with a fantom 3.5 and love the combo. Running 2.2 @63

@nolimitrc1

3 жыл бұрын

@@Lushiouscorey2011 r1 wurks esc can handle a 3.5 i didnt know that what i really want to know is what can handle a 3t

@Lushiouscorey2011

3 жыл бұрын

@@nolimitrc1 the r1 will run it you just have to be careful with the tune and gearing.

@vincentfranchino2732

2 жыл бұрын

Best gearing to run on my bandit with 7700kv motor mamba monster 2 esc and foam rears for drag racing?

Is that castle motor better than the original no prep drag 1412 castle motor?

Nice video so what motor of the 3 would be best for my mamba monster 2 esc for drag racing? And what gearing should I run?

@kgrc0078

2 жыл бұрын

So, what I learned, the more torque the higher the amp draw. So, r1 would win this

Does this device work for testing motors without hall sensors? The manual seems to indicate it does but I don’t understand how it would. I’m looking to test the kv a bunch of smaller drone motors without hall sensors.

Great video.

@kgrc0078

4 жыл бұрын

Appreciate it 👍🏼

almost perfect 69420

@dboogeman2002

3 жыл бұрын

LoL it peaked 69515 before he hit the switch

Is the hobby wing V10 g2 5000kv 6.5 turn better for drag on my rustler 2wd 2s than the R1 3.5 turn 9500kv??

What about if you don't have a sensor wire to plug into a TP motor

@zachmachina

10 ай бұрын

I’d like to know this as well

You tested the Ruddog At two pole when the box says four pole.

Was the Ruddog loud or just not on the rubber pads? it sounded like it was vibrating against plastic?

@kgrc0078

Жыл бұрын

I think I just didn’t set them right

What are you looking for in a motor, AMPS or RPMS?

@kgrc0078

3 жыл бұрын

More rpm of course. But it seems to show also that the higher torque motors use more amps 👍🏼

motor castle 7700kv can use for rc scale 1/10 on road sir ?

@kgrc0078

3 жыл бұрын

Yep. It’ll fly.

I need to make my Losi 22S faster what motor should I purchase?

@nolimitrc1

3 жыл бұрын

Lmfaoooo im in the same boat man i have a trinity holshot 3turn motor and an mmx8s ive capped at 2.3 seconds on 2s but the esc is dieing i would just go with the maclan drk 160 esc and the 3.5t maclan mmr motor youll thank me later

@fastfordstang13

3 жыл бұрын

@@nolimitrc1 Will thanks for the help

Braddah that was an awsum video mahalo for all you do 🤙

@kgrc0078

3 жыл бұрын

Thank you!!

Sup bro have typhon v5 v6 thinking bout replacing with mamba 1717 1650 ..what do you think for both high speed n dirt track…which pinion ⚙️ for both

@SebastianLong

2 жыл бұрын

That's a hell of a motor for the Typhon. With that motor you would be able to run pretty much any gearing you want with the light Typhon. At least the gearing you could fit with the motor mount. That being said, the 1717 could handle a lot more gearing in a Typhon. Your best bet is to experiment with what gearing works for your track. The highest gearing you can run doesn't mean it will make it good on your track. Run laps with each pinion and figure out your best average time for each pinion size. Either way, start with 2 teeth higher than your stock gear. Jump up two teeth for every 500 kv difference is ideal. So for example your stock pinion is a 16t and you are running the stock 2050 kv and you installed the Castle motor, you'd want to run a 20t pinion on the Castle motor to get approximately the same speed. 2050 - 1650 = 400.

@chevyryda60

2 жыл бұрын

@@SebastianLong thanks a lot

Is the castle 7700 a good motor for drag racing?

@kgrc0078

3 жыл бұрын

I like it. Very competitive 👍🏼

@raymondnerona4240

3 жыл бұрын

@@kgrc0078 What is the best gearing for drag racing?

WHAT ESC WOULD YOU PAIR UP THAT RUDDOG MOTOR WITH ?

@kgrc0078

3 жыл бұрын

I did the hobbystar 160a turbo esc. Man, it’s FAST

@sammygonzalez7627

3 жыл бұрын

@@kgrc0078 Thank you 🙏

@kgrc0078

3 жыл бұрын

You’re welcome 👍🏼

@vhopkins6784

3 жыл бұрын

Go castle

@rcs_rc_az961

3 жыл бұрын

@@kgrc0078 after almost a year, do you have an update with the ruddog/hobbystar combo? I am curious to learn how the esc has held up. Are you only limited to the program card or can you access easier settings with an app at all? On the ruddog being loud, do you feel better bearings from the start would have improved any concerns? Thanks for these videos, keep it up!

Why no hobbywing??4.5t?????

Is castle a good drag motor?

@kgrc0078

3 жыл бұрын

It’s not bad at all

Can you use.this on a brush motor

@FromthePits

3 жыл бұрын

These units are for brushless motors only bud.

On the r1 how can I back down the timing?

@kgrc0078

3 жыл бұрын

On the back of the can there are 3 screws. Loosen them. You’ll see numbers on the side at the back. Timing will be like a pinion gear; higher the number the faster

@kgrc0078

3 жыл бұрын

But also remember that more speed = more heat so be careful

Wow

9100kv??

That budget motor tho.

I called castle directly they recommend the 5700kv for drag racing 🤔

@kgrc0078

3 жыл бұрын

Interesting 🤔

@HairBandDan

3 жыл бұрын

@@kgrc0078 I must note I told them I was converting a slash to a no prep drag car and i mentioned above video the tech said 7700 would run hot 🤔

@lodakota94

3 жыл бұрын

Speaking from first hand experience. The 7700 is fast on conservative gearing but will get hot fast. But it’ll hold up. Used to run mine in a slash on 3s lol.

Is the higher the kv does that mean more hp?

@kgrc0078

3 жыл бұрын

Correct! And the lower kv the more torque 👍🏼

@stezzylocoaine4176

3 жыл бұрын

@@kgrc0078 so which is better cause i need a new motor

@kgrc0078

3 жыл бұрын

You can’t go wrong with R1. But for the same price you can get the new maclan DRK 💪🏼

@stezzylocoaine4176

3 жыл бұрын

@@kgrc0078 ok it’s gonna be for drag racing

@kgrc0078

3 жыл бұрын

Yep. R1 3.5 all out or the maclan DRK 👍🏼

You had the last motor set on 2 pole when it was a 4 pole. You did not get accurate KV or RPMs.

That R1 motor had a really bad sensor board, 40, 35, 32 is way off

Does the lower current men less torque? While lower amps may be efficient the motor with the less torque will take longest to achieve high rpm.... the Ruddog will come last in that drag race I reckon

@kgrc0078

3 жыл бұрын

I believe you hit the nail right on the head my friend 👍🏼

@ng8tvinfluence78

3 жыл бұрын

@@kgrc0078 ok, so is there a way to measure torque on that measuring rig or is there a way to calculate torque from specs?

@chrismagallanes8858

Жыл бұрын

So lower the number means for more torque

The louder the motor means it's shim wrong. And dry bearings.

Hear to ask a ? Seen a surpass 3.0t 11000kv around to test😂😮

I blew up my other 7700kv motor at 235thousand rpm and it blew up

@kgrc0078

3 жыл бұрын

Did you run it on 6s?? 235k 😮

@coltoncrawford95

3 жыл бұрын

@@kgrc0078 nope strait 2s

@kgrc0078

3 жыл бұрын

Lol how’s that even possible??

@coltoncrawford95

3 жыл бұрын

@@kgrc0078 we threw all the timing at jt

@Fly2kill1

Жыл бұрын

Yeah. No you didn’t.

Its gonna pull more amps when it has a load. More kv will pool more amps. That ruddog will not last its not smooth at all.

@kgrc0078

4 жыл бұрын

You get what you pay for 🤷🏻‍♂️

@billthomas9109

4 жыл бұрын

the motor wasn't setting correctly on the test stand. you can see it is almost falling off the right side

Thank you! Unfortunately, this testing doesn’t give any idea of the actual torque produced......so interesting results , but not really helpful or predictive......cool gadget.

@kgrc0078

3 жыл бұрын

It’s useful In a way that it tells when the motor is somewhat worn out cos it’s kv rating drops. I had an old 6100kv that only puts out 5800kv now.

Say "RUDE DOG"

R1 motors are just over priced rebranded surpass motors. You can get just as good of a motor for half the price in the rocket v5r or the hobbystar pro v3.