music in the background sounds like some old school porn music..lol

Wooooww! Finally… upload three days after I figure out how to install mine. I've been waiting for months for an instal video. It took me 9 hours and wanting to throw the intake in the trash lol

thanks im going to instal tomorrow got mine from shop. in norco ca keep up the good work

Another great video from ***** . Was going to do the Skunk2 CAI , but I don't touch wires lol. Not a fan of cutting up factory wires. Great video though. Wanted to hear it running after install.

Quick question, is it optional to get a tune? Or a must? After getting the intake installed?

What size wire were you using to extend he cables?

Hey I just installed the intake haven’t got it tuned yet but it’s giving me a code p0172 if I flash it would this code go away

Hey I just installed this intake and now i got a battery light on and a warning saying check charging system. What do I do?

just wondering would this fit on a ex model instead of a si? or is the motors to different? i already have a skunk2 exhaust so would be nice to get the same intake

Great install video!! Helped a lot where the instructions didn't.

@procivic

7 жыл бұрын

+Jon C Glad to hear it helped! :)

u think this model fit for honda civic 2012 si sedan (SKUNK2 943-05-0120 - COUPLER - USE W/ 343-05-0200 & PRO SERIES INTAKE MANIFOLD, RBC OR SIMILAR)

Where do I get the extension hose, extension wires and wire connectors

For the maf sensor what type of wires are those.

will this work on a CSX-S?

Can the 3 combo k-tune fit on a 1999 SkyLine 25 GT-X Turbo

what’s the best intake for the 9th gen does anyone know

Does the flow have to point up upward or downward

I think the K&N is the best intake to get. It might make 1 or 2 hp less than this Skunk2 but the ease of installation, no cutting wires or relocating the battery is worth the 2 hp loss. Plus it's cheaper.

@procivic

9 жыл бұрын

Armin Tamzarian Just for comparison's sake, keep in mind K&N advertises a 10.59hp increase, but it is a SHORT RAM intake. Those dyno #s are with a relatively cool engine with the hood open and a fan on. The real world #s for cold air intakes like this Skunk2 one are always higher than short ram intakes. The reason is due to heat soak: short rams eventually start sucking in very very warm under the hood air.

Do you need a tune after installing?

Will this trigger a check engine light?

Hey dude I just got finished with my install yesterday and have been trying base maps with flashpro.(it's a different car now) I really appreciate your videos, I used the phase 2 siri strut bar video you made too. You were right about those washer on the bar LOL dam my stubbornness! Thanks man got any pointers for me with the tuner?

@procivic

7 жыл бұрын

+Ben Ford I'm glad to hear the videos helped you out! For the tunes, we mainly recommend simply choosing one that is closest to your set-up. If you need something more specific, having a professional tuner create a custom map for you is best recommended.

Just installed it today, this video helped a bunch, thanks!!

@procivic

7 жыл бұрын

+Gregorio Santana Glad the video helped! Thanks for watching!

Where you put the ECU ?

I just did mine today :) and also grate video 🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥

@michaelrich7466

4 ай бұрын

Realistically how long did it take you?

@dafb6dafb62

4 ай бұрын

@@michaelrich7466 like about 45 minutes to an hour 🥲

Could you ship to Vietnam? I'm want push 1 set, waiting for you reply

Hi, i just have installed a CAI... Got some problems like there are not "nipple" to attach the vacuum hose. Does not include cables to extend at the flowmeter.

@procivic

9 жыл бұрын

roberto vile If you bought the intake from us, please email in to customercare@procivic.com so we can help you with that. Or you can call us over the phone, which is probably easier. It sounds like you may be missing a couple wires. As far as the "nipple", the Skunk2 intake tube definitely does have one for the breather hose to connect to.

@blackxthink

8 жыл бұрын

+roberto vile You had me at nipples

how many more hp this skun2 intake give that the original intake ? thanks

@ Joseph the Injen v2 is actually pretty awesome. The v1 sucks yes.

Does this intake require a tune

wouldnit be possible to fix up the 2016 base model with cold air intake and exhaust im not tryna be ricer or tuner just want my car to sound and perform good

@procivic

8 жыл бұрын

+ace quides It is possible. However, at the moment, we are still waiting for manufacturers to complete development on the parts

where do i put the ecu back

Air barb size?

anyone know where the fuck i can buy a breather tube skunk2 doesn’t sell shit separately apparently

FYI this intake and the PRL CAI. R they only 2 that actually make power ppl this intake its worth it just cutting up all those wires sucks ass

Hi quick question please.. Is the check engine light comes on when you installed the skunk2 CAI?

@procivic

8 жыл бұрын

+john bryan talana We did not have a check engine light come on when the intake was installed

Do I have to remove the fender liner in order for the filter to fit? Because it won't fit since it's blocking the way.

@procivic

7 жыл бұрын

+Isaac Arenas Do you mean permanently? If so, it does not. You should be able to reach it by only removing a small portion of it between the bumper and wheel (as shown at 4:41 in the video). Alternatively, you can remove the front bumper for more room.

Hey pro civic's, just got my s2 cold air intake installed and the engine light came on for emissions. If I get it tuned will the light go away and were can I get it tuned. Will the performance shop were I got it installed do it?

@procivic

8 жыл бұрын

+Manuel Botello It depends on how you have it set-up. With other modifications, you may require a tune.

just pulled the trigger on S2 CAI. hopefully i can install this lol

@procivic

8 жыл бұрын

+Acolis You should be OK! Fairly simple install

@Acolis

8 жыл бұрын

+ProCivic.com fairly simple. lol. i mean it wasnt the worst thing in the world but it was fairly indepth for a cold air intake install. no one should be discouraged from that statement... really just needed to take my time with everything but i got it done with help in about two hours or so.

@0bsessionsxtreme

6 жыл бұрын

I just did like 2 hours ago lol hope it comes with everything heard of people getting them with missing parts

Nice video, only one question please...When you say, you get 10 to 14 hp, that is without touching the ECU?

@procivic

9 жыл бұрын

R PT That is correct, and basically what is advertised by Skunk2. We have not verified that on a dyno, but it seems reasonable given the gains other similar intakes are getting.

best intake is the one that has the pipes bend and the filter goes RIGHT where the stock thingy was in the bumper. the stock system is INCREDIBLY disgusting and inefficient. its amazing what a true cold air intake does to these cars. and yes, it will be ok from rain and all because the engine has a splash guard under the front bumper too!

great video guys. I just wish you would have done this one a while back when I installed mine.

@AngelMartinez-du7ro

5 жыл бұрын

How much hp you won with this intake?

@procarstudio thanks for the video! Did you guys use Hondata for the tune? If so, what calibration did you use. Thanks again!

@procivic

6 жыл бұрын

We did use Hondata to tune for it. However, we used a custom tune for this setup.

@jairochable6030

6 жыл бұрын

PRO Car Studio ah okay, thanks. I really didn't find any calibration that works well with this intake. Great video, thanks again.

A skunk2 down pipe install video would be very helpful

@MrIhavedonuts

5 жыл бұрын

Wasn’t hard when I put my full race downpipe on. Except one of the bolts for the stock downpipe stripped. I had to mig weld a nut on it to get it loose. I’d advice replacing the bolts with a grade A bolt

When you go to bolt on the intake with it’s mounting bracket, you should actually show it @21:51

can i install the stock back again if i want to get rid of the skunk2 CAI?

@procivic

8 жыл бұрын

+Maury Sedano Yes, it is very possible to install the stock intake if the needed arises.

Is there any way around extending the maf cable? Seems a bit sketchi to me to ne honest

@procivic

8 жыл бұрын

+zuno jose Unfortunately, there is not. It has to be extended to reach the new location of the MAF.

@zunojose

8 жыл бұрын

+ProCivic.com i just installed mine and skunk2 provides an extension for the MAF sensor. I also was able to stretched the negative wire that needed to be extended by cutting a couple zip ties from the factory harness it gave me Enough play to plug it . No wires cut at all

@procivic

8 жыл бұрын

+zuno jose That good to know! Thank you for sharing. The kit may have been updated slightly since we posted the video.

Will it work if your car is not si? Because my care is just the standard car.

Hey bro by any chance when you installed your intake did your check emissions light go on? I'm thinking cus The car is now running rich and I need to tune it now? Any advice ?

@procivic

8 жыл бұрын

+Erik Jimene Ours did not, but this can be caused by small leaks on some of the emissions lines near the throttle body. We recommend double checking all the lines to make sure they are properly sealed.

@warlinj

7 жыл бұрын

Erik Jimene my emissions came up too and it smell like something burn when I opened the hood

@procivic

7 жыл бұрын

We have seen some 9th Gen Si's run rich after installing this intake with other modifications. I would highly recommended getting your vehicle tuned with a FlashPro. It will add a good amount of horsepower as well. Even an e-tune would be fine in this case. Email us at customercare@procivic.com if you have additional questions about this.

Where did you put the ground wire from the negative terminal? Wont reach the stock location after relocation.

@ericbethmann8798

4 ай бұрын

same problem where did u end up grounding it

hey pro love ur vids going to get skunk2 wats the diference betwen cold air intake n composite cold air on ur website please let me know

@procivic

8 жыл бұрын

+george vargas Skunk2 uses a composite plastic material that is more heat resistant. Most other intakes are metal which can absorb heat.

I installed my s2 intake but it came with a maf sensor extension harness. Is it normal for the power steering, emissions, and vsa system alerts to go off?

@procivic

8 жыл бұрын

+Matthew Sproat This should not happen. Double check that all the wires are connected properly. Also double check that all the wires that were spliced were connected to the exact same wire at the plug. Check for any leaks or loose clamps as well.

@matthewsproat7049

8 жыл бұрын

+ProCivic.com they went off. when I turned the car off and tried to start it, it didn't get any power from the battery, I had to jump it. the imid isn't operating now.

@procivic

8 жыл бұрын

+Matthew Sproat Please contact customercare@procivic for detailed tech help.

@jjovel7355

6 жыл бұрын

Did you figure it out? Just installed mine and im in limp mode.

hey procivic.com if I install the cold air intake, will I need to tune my si? my friend had to tune it because there was an engine light he had that came up.

@procivic

8 жыл бұрын

+John Burnett It depends on the intake and the mods you already have. You can normally do without a tune, but it is highly recommended

@johnburnett1319

8 жыл бұрын

+ProCivic.com alright, thanks!

***** I was wondering if rywire could make a female and male wire instead of cutting factory harness I've had my intake sitting for about 2 months now I don't like the idea of cutting up my harness gf bought it as a gift

@procivic

9 жыл бұрын

They could possibly, but Skunk2 may be making this in the future as well. For now, please email into customercare@procivic.com and we'll see what options there are.

do you guys have a throttle body upgrade from a Honda Civic 06-11 ex sedan

@procivic

7 жыл бұрын

+will n Unfortunately, we do not have a upgraded TB available for the R18 models, only si models.

I know this vid is about 3 years old and had my civic for a couple of years and I just now can afford to do stuff like this. Like the vids though

What are your thoughts on breather filters? Are they a good part in addition to an intake?

@procivic

9 жыл бұрын

TheNuke95 The breather filters are more for when the intake you're getting doesn't supply the proper connections. The breather filter allows you to still have filtered air entering your valve cover. With this intake you don't need a breather filter.

@TheNuke95

9 жыл бұрын

i heard it weakens your performance. i have the injen cold air intake and im debating whether to get one. wouldn't it be more beneficial since you're not recycling nasty fumes to your intake?

@procivic

9 жыл бұрын

TheNuke95 I think you're talking about an EGR valve, which recirculates exhaust gas. This breather hose simply allows the crankcase to "vent" pressure properly. Most of the time the air actually goes into the valve cover from the intake, and not the other way around.

He guys, it's been a couple months since I bought an si 15, looking for the best intake I can get for max performance in the car, what would you recommend? The car is stock I'm looking foward to tune it up!

@procivic

9 жыл бұрын

Carlos Sanchez This Skun2 intake will probably make more power than any of the other intakes, but the install is tougher. If you want an easier install with almost as good power gains, try the Injen True Cold Air Intake: kzread.info/dash/bejne/rJl7s89morzcgM4.html

@deRockmoto

9 жыл бұрын

***** what are the power gains from a skunk2? I'm in the middle of a toss up with the true injen Cai and the skunk2.

@procivic

9 жыл бұрын

I believe the S2 power gains are advertised around 14-16 hp or so. A little more than the Injen I think.

@deRockmoto

9 жыл бұрын

Okay thanks :)

I have a stock 2013 civic lx coupe with 140k miles! What mods do you all recommend I get? Looking for good exhausts or intakes to improve sound quality and hp increase

@staticaesthetics697

2 жыл бұрын

Sell that shit and get an si

@NitroDonkey117

2 жыл бұрын

@@staticaesthetics697 loll fax

@NitroDonkey117

2 жыл бұрын

@@staticaesthetics697 they double the price tho

@zenxen7668

2 жыл бұрын

@@NitroDonkey117 pay to play

is the installment the same way for a 07 si?

@procivic

7 жыл бұрын

+jay_ Castro It will be similar, but not the same. It would be best to follow the directions for a 06-11 si for a proper install.

You guys have any plans for an exhaust installation video?

@procivic

9 жыл бұрын

Doomerism Yes, in the near future.

Was it worth it installing intake manifold on 9th gen?

@procivic

6 жыл бұрын

This video is actually for the Cold Air Intake. Yes, it was well worth it.

Hi is there an intake available for the Honda CRZ?. Thanks.

@procivic

8 жыл бұрын

+sean power Yes, but not from Skunk2.

Has there been any confirmation that Skunk2 includes wire extensions so you do not have to cut and splice? The intakes that you are currently selling at procivic.com, are they coming with these extensions now?

@procivic

9 жыл бұрын

Mark Pollard All of the intakes include wires, but not a Plug and Play harness that allows you to just "click" in the wire extensions. You have to manually wire them, which is not that bad. I have only seen a few customers, like Anthony Colon (below), comment that they received "extended cables". I'm not really sure if that means a "harness" or not. That customer will have to be more specific about what they received.

How far away is the Air filter from the tire? I install the CAI on and it's like 1-2 inches away from my tire

@procivic

9 жыл бұрын

Milton Segovia It is usually about 2 inches from the fender well cover, but it's still hidden behind the fender well cover, so no worries about the tire every making contact with it. The tires never really contact the fender well cover, so there is no way for them to ever reach the air filter. Not sure if that was your concern or not.

I have a civic si 2015 and I use pandora with the Bluetooth but it keeps disconnected

@omaralvarez945

4 жыл бұрын

try a battery reset. disconnect both neg and pos terminals from the battery and with a jumper cable, touch the neg and pos terminals and leave it like that for about 15 mins. this resets all the electronics and its basically a "turn it off and turn it on" fix. Doesnt always work.

@omaralvarez945

4 жыл бұрын

edit the cables not the posts.

Do u have to tune the car after installing this intake ??

@procivic

8 жыл бұрын

+Larios331 A tune is not required, but you will get a bit more power with a tune! :)

@xanthony1919x

4 жыл бұрын

A TUNE IS REQUIRED WTF🤦‍♂️

But then you have to tune it more $ . I wish there was an app instead of a Hondata to tune

torque?? wish torque val. is the trans mount?

@procivic

8 жыл бұрын

+Hector Soto The FSM recommends 55 lbs/ft

is there a C.A.R.B # for this? Im in Cali

@procivic

4 жыл бұрын

Please contact us directly at customer@procivic.com to confirm CARB on our products.

Does this intake fit the 2012 Civic EX?!

@procivic

8 жыл бұрын

+JAGExecutiveServicesInc No, only the Si models.

@procivic

8 жыл бұрын

+Danny Lugo If the intake works and is wired correctly, you no longer need that plug. Otherwise, if you do really need it, you will have to purchase a replacement from a Honda dealer.

How can u get to the battery if u need to jumpstart? And will this hydro lock my car?

@procivic

6 жыл бұрын

+Papo cruz We found there is still plenty of room to be able to connect cables to the vehicle. As for hydrolocking, it is very unlikely. The entire intake filter would need to be submerged in water for something like this to happen. We've driven through plenty of rain and have not had an issue with this.

how much horsepower can you get with this?

@procivic

9 жыл бұрын

Anthony Garcia We have not dyno'd it, but I'm guessing around 10 to 14 hp.

Why such a long time between videos? If you need a car to do work on let me know man

does this system claim to provide any hp gains??

@procivic

8 жыл бұрын

+121dodgers There are certainly HP gains with this system. We also highly recommend a tune for best results. With a header, exhaust, and a tune, we saw gains up to 35HP.

@121dodgers

8 жыл бұрын

+ProCivic.com hey thanks for the reply. i really appriciate it. i was asking because i was considering this skunk2 cai and the one that k&n offers. this system seems a bit more technical. not thats an issue, but having to move stuff around and drilling holes JUST for aesthetics plus having to tune doesnt seem to pay off. i am still considering the skunk2. but, the k&n seems to pay off more by instant gratification even if the gains are only minimal... without having to tune. i am not a hard core tuner/racer. im just looking to enhance my cars performance from stock. complete intake and exhaust system(header, manifolds, cat back,) in adition to the cai are my goals, along with a tune. skunk2 coilovers 2 are already mounted. so i was thinking of keeping everything with the same brand and skunk2 seems pretty legit and has a good reputation just from looking around on the internet. anyways. thanks for this video.

@procivic

8 жыл бұрын

+121dodgers This is mainly for the most amount of power. However, if you want more details on this kit or other possible intake options, please email customercare@procivic.com for more in depth information

that's sucks what about a smoke tail light for Honda civic 06-11 4dr

@procivic

7 жыл бұрын

+will n Please email customercare@procivic.com for better assistance on what is available for your Civic.

+ProCivic.com For some reason when i installed i mine the check engine light keeps coming on/off at random times. When its on the vtec doesnt kick in. It keeps saying its running rich bank 1. I've been told i need to tune it for it to go away. Is that true?

@procivic

8 жыл бұрын

+Marco Alonso Double check all connections and couplers first. It should not require a tune, but would help with more power. If you are still having troubles, contact us at customercare@procivic.com for tech assistance.

You guys can skip cutting/splicing the wires at 16:18. All I did was follow the wires and take it out of the plastic housing. The wire is long enough to reach with slack, just buy some more of the plastic tubing and add it for factory look.

@procivic

9 жыл бұрын

Alexander Machuca Interesting that you were able to do the install without the wiring. There did not seem to be enough slack on our setup for us to feel comfortable using the factory wire length.

@CL0WNS3R

9 жыл бұрын

***** I carefully opened the ziptie clipped into the frame by slipping the tip of the razor blade in between the tooth of the ziptie. opened it up. Opened the plastic holding the wire, extend it and connect. for the plastic housing. tape it back up and use the same ziptie clip used to hold it back in place. one less wire to cut was my goal.

@procivic

9 жыл бұрын

Alexander Machuca Yes, I believe you're talking about one wire though, there are still others that would come up too short and need extending.

is this intake legal in ca?

@procivic

8 жыл бұрын

+Aljohn Cruz Please email our customer care at customercare@procivic.com so that they can double check for you

Actually I bought it couple weeks ago and it came with extended cables so I dint have to cut anything

@procivic

9 жыл бұрын

Anthony Colon So it is definitely possible Skunk2 has revised the intake recently. The intake from this video was ordered several months ago I believe.

@pandeth1

8 жыл бұрын

Where did u buy it from?

@procivic

8 жыл бұрын

+Kenneth Manas We sell it on our site, here's the direct link: www.procivic.com/pages-product_car_part_info/product-2277/index.html

@pandeth1

8 жыл бұрын

+PRO Civic with the extenders cable where I don't have to cut the wires? Cutting the wires is sketchy.

@procivic

8 жыл бұрын

+Kenneth Manas Huh? Can you re-phrase your question? I think you're asking if you still have to cut wires with the extenders. The answer is yes, but as we show in the video, it is pretty straightforward and the wires will have a very solid connection afterwards.

is this carb legal?

@procivic

8 жыл бұрын

+Danniel Baldoza I'm not sure of the exact status of it at the moment. I could be CARB Pending. I think you will need to contact Skunk2 directly about it if you need specifics right now. Otherwise, we'll most likely (eventually) get an update from Skunk2 with the status.

that shit looked like a fucking process I never wanna do. why they have to make something that is so simple look so difficult lol

way to much rewiring and relocating shit for this intake... more you got to do more risk of something going wrong... wanted it but now leaning towards a k &n typhoon or something simple. also looks like once the intake is on it makes battery replacement so much more difficult.

For this much work and modification it should give 20hp without a tune, I'll stick to a K&N drop in with HPS silicone intake tube........way too much work for what it offers.....

Wasted. Not getting skunk. Never seen an intake where u have to wire and jack up the tranny

Video good but was given a thumbs down due to the extension wire cutting and moving components around. Injen cai all the way disappointment to see skunk2 expected that much work for a cai install

@procivic

9 жыл бұрын

Eric Martin Yeah the wiring part does make the install a bit more difficult. I imagine Skunk2 map provide a harness in the future. Overall though, it does not add too much to the total install time.

@RedDetailAZ

9 жыл бұрын

That's true procivic I just hate seeing wiring cut especially when your ride is the 15 si with extended warranty

To much work for what your getyimg2

Why would I ever splice in my car is wiring harness that is the old ass 90s way of doing things Like some rigged shit there Here’s an idea get a laptop get a Hondata and do it the right way

Vid sucks you skip the set that you have to extend the MAF five wires and how to install the battery tray,vid sucks cause know zooms in on how to.... My cousin's bf bought this intake and it had missing 5 wires for the MAF and only two for the negative signal wire only. Don't buy this intake if its offer at a reasonable price it maybe missing a few parts. We had to take it all out and put the stock air box back in cause the intake kit wasn't complete.

@16ValveVtec

9 жыл бұрын

kenneth man this intake is so expensive why didnt skunk2 just include a freakin jumper harness to make this a plug and play setup, idiots!!

@suicidal_racing9698

7 жыл бұрын

16ValveVtec mine came with the jumper wire

that is not what a 2013 si looks like under the hood

@white_devil73

7 жыл бұрын

Derick Cory ok. when he moved the battery it threw me off. get a K and N Typhoon amd keep everything where it belongs.

@danverdejo3356

6 жыл бұрын

Derick Cory l

This guy is a sped

Just figure it out yourself this guy has downs