Thanks so much for this too. I've never even seen the reservoir before so good to see that.

Absolutely brilliant video. Some one bumped my car last week. Now the water doesn’t stay in the bottle. I am going to follow this video next week 🤝

@HatBoyHarvey

3 жыл бұрын

Thanks and good luck, hope it goes well :-)

Всё не перестаю радоваться, что нашёл этот канал. Ну золотые руки! У меня тоже бачок течёт

@HatBoyHarvey

2 жыл бұрын

Отлично, что вы нашли канал. надеюсь, вы смогли заменить или отремонтировать бутылку :-)

Just completed this on a 1.4 petrol. Loads more space than on the diesel in the video, so much less jiggling about. Thank you for the video!

@HatBoyHarvey

2 жыл бұрын

Thanks, great to hear that :-)

Great work. Could you do a video on the different type of common connector types on vw|skoda and how to operate then. Would be a really educational video for all DIYers. Last day after getting to headlight connector had a hard time figuring out how to disconnect the thing, seems easy but with out the proper instructions a first timer would break it sometimes.

@HatBoyHarvey

3 жыл бұрын

Thanks. The trouble is there are many connectors with different types of clips. The main ones that is often difficult and can break are those I showed in this video at the start taking off the bumper electrical connectors to the fog lights. many are like that. I've shown these on a number of videos, I think this one shows a broken one: kzread.info/dash/bejne/jJWppsuHk7ScY8o.html I am planning to do one though on some other connectors, I'm just waiting for the parts to come.

That's proper fiddly, thankfully don't need to do it at moment, but this is super useful if the occasion arises, many thanks for all your time and effort with your DIY vids 👍

@HatBoyHarvey

3 жыл бұрын

You're very welcome. At least the video is there if need be :-)

Thanks i have ben waiting for this

@HatBoyHarvey

3 жыл бұрын

Enjoy

@fotisparolas7732

3 жыл бұрын

@@HatBoyHarvey Thank a lot Sir!!!!

Luckily I didn't need to remove the bumper or the bottle itself, but the bit about the wheel arch liner saved me from the clutches of KwikFit. All I had to do was move the line out of the way enough to get decent hand-access to the bottle, where I found part of the pipework/joinery had partially come apart. Popped it back in like a dislocated shoulder and my water bottle is no longer leaking. Thanks for tip!! :D

@HatBoyHarvey

Жыл бұрын

Great, nice one, glad to have helped :-)

Is the same bottle on Polo MK4 9N?

Great thaks to you sir 😉😉

What would you think about fluids servicing. Stuff like flushing the power steering fluid and gearbox oil. There's nothing in the manual about it but I would think it's best to replace these oils since overtime they would wear and lose lubricity

@HatBoyHarvey

3 жыл бұрын

you only need to top-up the steering fluid, but the gearbox could be changed, I changed mine, but it's not such a big issue if the box works ok. If you change it you need to get the right oil as the viscosity is important for gear changes to be smooth.

I just payed my mechanic in Istria to put a new one, parts were around 30 pounds, and work 20. Its best to replace bottle, pump and hose at the same time as parts are cheap in comparison to work.

@HatBoyHarvey

3 жыл бұрын

That's a bargain price and probably worth it to avoid the hassle, but IMHO cheaper and more satisfying doing it yourself :-)

GREAT video ! Thank you soooo much

@HatBoyHarvey

Жыл бұрын

Glad it was helpful :-)

very good.thank you

@HatBoyHarvey

3 жыл бұрын

Thank you too

أنت إنسان رائع وماهر وفنان في عملك تقوم بعمل رائع وفيديواتك متقنة ومفهومة شكرا لك على مجهوداتك لعلمك أنا من الجزائر اتابع عملك جيدا ومهتم به وتوجد عنديfabia vrs اصلحها بتتبع فيدياواتك شكرا ثانية

@HatBoyHarvey

3 жыл бұрын

شكرا لتعليقاتك ودعمك اللطيف :-)

cheers buddy 😉 great video as all ways 👍 do you have eny service time on power steering fluid and dus it needs to be replaced!!! 👍

I will ttay to change to day 😄😄

👌🏻

If just replacing washer bottle pump can it be done via wheel arch? Can no longer hear the washer pump when trying to clear windscreen, checked fuses all good so going to replace pump next.

@HatBoyHarvey

3 жыл бұрын

Yes, you just need to undo the front edge of the liner and bend it back a bit. If you have a test light or multimeter you can test the pump connection first to see if there is power there when you activate the switch.

@shoaibhussain8804

3 жыл бұрын

@@HatBoyHarvey cheers mate appreciate the reply, think I'm gonna wait till the weather gets better and give it a go 👍

I can't find my rediator fan problem solution plzz make a video for it . It's problem is fan will continue all the the time when I was changed it ..

Hy Harvey,got one problem,whenn i put liquid inside got leaking somweare.pipes or something alse?

@HatBoyHarvey

3 жыл бұрын

where is it leaking?

Todays job………… As always made easier by your good self 👌🏻

Hey. Thanks for the video. I have a seat leon mk1, which has p0135 heater circuit problem. Could you do a video for checking the sensor and wiring . Because these cars probably have same sensors.

@ilkay8551

3 жыл бұрын

Here is mine, ibb.co/th698YD

@HatBoyHarvey

3 жыл бұрын

I'll look into doing a video on this at some stage, thanks. Is this on the 1.4 fabia? have you replaced the pre-cat O2?

@ilkay8551

3 жыл бұрын

@@HatBoyHarvey 1.6 16 bcb engine. Havent changed yet.

@HatBoyHarvey

3 жыл бұрын

First check for obvious connection/wire breaks etc and then you can test the resistance of the heater coil to see if it has either too much or a short which would indicate a new one needed no doubt. The wires would be the same colour. you can also do a live voltage test with the engine warmed up and then introduce more air to see if the reading is as expected and changes you just need to know which wire is which for your particular sensor.

@ilkay8551

3 жыл бұрын

@@HatBoyHarvey I am reading some volues on multimeter but i dont know which value i read. The opposite side of the sensor connector i read 10.5v.

It would be of a great help to see how to repair the clogged nozzles or how to take them off...I think my left is not good...maybe to clean it with needle, don't know what to do...

@HatBoyHarvey

2 жыл бұрын

I agree, Unfortunately these prove very difficult to clean out when the spray pattern goes faulty, it is best to buy new ones, but I haven't found after-market jets to be of any good, only the OEM ones work well. I have always wanted to find an alternative jet that is cheap, sprays well and can be cleaned well. I'll keep looking and let everyone know If I find a great alternative :-)

@robiszi7932

2 жыл бұрын

Great, thanks. Just to add, I've tried yesterday with the needle,pushed it through, and after sprayed with WD40,then will see...and maybe could be the issue with weakened pump, or some sludge that is down there in reservoir...I want to see 2 nice decent triangles of washer fluid on my window, but the rightone is not so good, it is better now though(without squirting),but not as it should be...and washer fluid consumption is still high

I found out that my washer fluid is leaking! It is coming out of my bumper. I looked for the tank and its look like the motor is leaking. I think that the rubber sealing is defect, how can I repair it?

@HatBoyHarvey

2 жыл бұрын

I would take the motor off by pulling upwards and then clean the seal thoroughly before re-inserting it. That should work, if not then silicone sealant may be an option, but if not a new unit I think would be the only option.

@SirDrakeNewcanon

2 жыл бұрын

@@HatBoyHarvey Your video was a big help! Thanks! I ha done exactly that what you wrote! I took out the motor, cleaned the rubber sealant, but added an o ring on the shaft of the motor. As second I thought on silicon too!

Hello my frend... My fabia have horn problem... Dont work... Maybe you can help me...

@HatBoyHarvey

3 жыл бұрын

Have a look at the fuse first then test the connecting wire that goes to the horn behind the fog-light grill. if there is enough power 12v+ power suspect the horn unit which you could also test separately and also maybe adjust it as that maybe all that is needed (I can't remember if these are adjustable or not, if not then it will need replacing). If the switches inside the steering wheel are suspect then you will have to take that cover off also.I will do a video of this at some stage :-)

@MrMleri

3 жыл бұрын

Maybe horn is did... Or rele under steering wheel.... Thank you so much....

@MrMleri

3 жыл бұрын

@@HatBoyHarvey when i repair new one horn.. I show you... Yesterday I self make windscreen washer moter

And of course, the bolt where you need the extension is corroded, so the nut will not come off and the another end is in the plastic, so you can get it loose!

@HatBoyHarvey

2 жыл бұрын

All you can do is soak it with penetrating fluid and thin oil. If still no luck then you will have to take a lot more parts off to get better access.

Very nice job but very complicated construction/in meaning that you have to take off the bumper...

How long did it take?

@HatBoyHarvey

2 жыл бұрын

It was a bit of a fiddle finding the best way to remove it, that's why I did the video to help give people an idea of how to do it. Bumper comes off/on in 5 minutes and I'd give yourself half an hour to extract and install a new or repaired one, (took me much long with filming) but that is just an estimate and depending on experience it may take much longer or as little as 5 minutes :-)

I don´t understand what is the problem with this bottle to be replaced.

@HatBoyHarvey

3 жыл бұрын

Nothing, just showing how to remove/replace it :-)

@komoonkh

3 жыл бұрын

Theres no problem, he is just teaching us how to do it. Which is amazing and we all thank for it!

@theeagle8652

3 жыл бұрын

@@HatBoyHarvey and that is how a proper DIY-hero operates! 👍💪

@yt240robert

3 жыл бұрын

@@HatBoyHarvey well done. thanks for sharing.

I'm forever filling mine up they don't hold much water lol

@HatBoyHarvey

3 жыл бұрын

Very true, if you live in a dusty area or even on long motorway runs they need filling up a lot :-)

why they do so f... complicated! There is no different way to make it easier!?

@HatBoyHarvey

Жыл бұрын

If you take the inner metal bumper off it is easier :-)