Simulating Deep Drawing Process Of Cyclindrical Cup By Abaqus
Жүктеу.....
Пікірлер: 22
@foyjullahsumon17003 жыл бұрын
Thanks greatly! really helpful for Hybrid material analysis
@shawnhsiao71093 жыл бұрын
Thanks a lot! It is quite helpful for beginners to learn Abaqus.
@xueleizhao737 жыл бұрын
Could you please tell me when the punch stop move down? Is there any time limit for the punch?
@user-rb8zz3gy6n4 жыл бұрын
Thanks you for the whole analysis. At 6:30, how is the plasticity table is calculated? Any reference to make this table?
@parnianmokri93867 жыл бұрын
thank u so muchhhhhhh, really helpful, i wish u the best
@ilyasdedegil1247 жыл бұрын
Thank you for this great tutorial. How much time does this simulation take?
@akshaykumar-mw3iy8 жыл бұрын
thank you sir but how can I plot fld results for cup formed
@gauravpatil12997 жыл бұрын
can you show procedure of encased stone column in abaqus
@vietnamnguyen99346 жыл бұрын
anh có thể giải thích giúp em tại sao khi unload lại có hiện tượng blank nảy lên không ạ
@ramkumarraja74855 жыл бұрын
Can you send the whole file for this analysis.... Please??
@enzxo7154 Жыл бұрын
thank you very much could u help simulating the springback
@hazemismaeel14888 жыл бұрын
Thank you for this tutorial is it possible to simulate spring back Thank you in advance
@thaohoang7636
8 жыл бұрын
You're welcome. I hope it can help everybody.
@chirchan
7 жыл бұрын
yes
@saedelkelany75802 жыл бұрын
Thank you very much. could you give us the material sheet
@otetraffordchannel38605 жыл бұрын
what the Unit your answer
@Dickyhan5 жыл бұрын
what are the units of mass density, how do you go from 2700 kg/m3 to 2.7x10-6 lmao
@futbolero50000
5 жыл бұрын
he is working with mm instead of m. 1m^3 equals 1e+9mm^3. So your density is (2700kg/m^3)*(1m^3/1e+9mm^3) = 2.7e-6 kg/mm^3.
@kenzabouchaala88286 жыл бұрын
please would you tell me from where you take the mechanical properties of AA1050 and thank you in advance
@ahmedsok5294
6 жыл бұрын
did u found it ? cause i really need it !
@kenzabouchaala8828
6 жыл бұрын
yes I did, I found it in this article: "The theoretical and experimental investigation of blank holder forces plate effect in deep drawing process of AL 1050 material"
@bharat1534
3 жыл бұрын
@@kenzabouchaala8828 in this tutorial after coalition they gives warning because of that I didn't get results that warning are 'processing attributes defined on reference point can't be plottes by viewer' And 'Boundary condition are shown in local coordinate system in which they were defined'.
Пікірлер: 22
Thanks greatly! really helpful for Hybrid material analysis
Thanks a lot! It is quite helpful for beginners to learn Abaqus.
Could you please tell me when the punch stop move down? Is there any time limit for the punch?
Thanks you for the whole analysis. At 6:30, how is the plasticity table is calculated? Any reference to make this table?
thank u so muchhhhhhh, really helpful, i wish u the best
Thank you for this great tutorial. How much time does this simulation take?
thank you sir but how can I plot fld results for cup formed
can you show procedure of encased stone column in abaqus
anh có thể giải thích giúp em tại sao khi unload lại có hiện tượng blank nảy lên không ạ
Can you send the whole file for this analysis.... Please??
thank you very much could u help simulating the springback
Thank you for this tutorial is it possible to simulate spring back Thank you in advance
@thaohoang7636
8 жыл бұрын
You're welcome. I hope it can help everybody.
@chirchan
7 жыл бұрын
yes
Thank you very much. could you give us the material sheet
what the Unit your answer
what are the units of mass density, how do you go from 2700 kg/m3 to 2.7x10-6 lmao
@futbolero50000
5 жыл бұрын
he is working with mm instead of m. 1m^3 equals 1e+9mm^3. So your density is (2700kg/m^3)*(1m^3/1e+9mm^3) = 2.7e-6 kg/mm^3.
please would you tell me from where you take the mechanical properties of AA1050 and thank you in advance
@ahmedsok5294
6 жыл бұрын
did u found it ? cause i really need it !
@kenzabouchaala8828
6 жыл бұрын
yes I did, I found it in this article: "The theoretical and experimental investigation of blank holder forces plate effect in deep drawing process of AL 1050 material"
@bharat1534
3 жыл бұрын
@@kenzabouchaala8828 in this tutorial after coalition they gives warning because of that I didn't get results that warning are 'processing attributes defined on reference point can't be plottes by viewer' And 'Boundary condition are shown in local coordinate system in which they were defined'.