Working on this Conquest. Transmission was getting slow on hills after 30 minutes of use. This oil change seemed to cure the problem.
Жүктеу.....
Пікірлер: 45
@rugby3874 Жыл бұрын
I have owned my Simplicity for over 15 years and it is the best riding mower I ever owned.
@LawnGardenFun
Жыл бұрын
Yes, they are pretty darn good!!!
@RooneysSears014 жыл бұрын
Keith! First off, great to see a vid from ya and second, great to see ya tackle a transmission lol great vid my friend! I remember doing this on my Scotts and it really helped it, the fluid at a certain point must just really start to breakdown.
@LawnGardenFun
4 жыл бұрын
Thank you sir, greatly appreciated. It wasn't too bad of a job at all. Thanks for watching.
@1965Caliente4 жыл бұрын
There are so few videos of the Conqeusts on youtube. I'm about to buy a '20 so I can be pampered because of my health. Wish more owner videos were out there. Thanks for yours.
@LawnGardenFun
4 жыл бұрын
You are welcome. Thanks for watching.
@whatifyourwrong91532 жыл бұрын
I’m process of doing exact thing. When u filled the oil did you fill to the top or leave some room from cap or ? I’d greatly appreciate it
@LawnGardenFun
2 жыл бұрын
I believe if I remember correctly you fill to top of the chamber not all the way up the neck. Thanks for watching!!!
@whatifyourwrong9153
2 жыл бұрын
Liked and subscribed thank you for the reply
@mariolmarini3 жыл бұрын
Hi, I had the same problem. My conquest would'nt climb while cutting grass even on a slight incline. I'm sure I emptied out the wrong oil which was black in color by removing the front internal transmission filter. They filter was missing (fig. 17 page 20 of the manual). I then proceeded to fill in the hydraulic system from plug B in figure 16. Did I fill the oil into the wrong plug?. I think maybe I should have filled the expansion bottle with the oil instead. Did I make a mistake? Thanks for your advice. Mario
@LawnGardenFun
3 жыл бұрын
You should fill both chambers and then also put a small amount in the expansion bottle too.
@LawnGardenFun
3 жыл бұрын
Thanks for watching!!!
@mariolmarini
3 жыл бұрын
Thanks for the advice...
@georgehofgren6123 Жыл бұрын
Great video, thanks. My Conquest (2011) has power steering, so two lines come off the Trans and pass thru two large filters, then go to the steering valve and to the cylinder @ the wheels. So, I would imagine i have quite a bit more fluid... Any ideas on changing that accessory oil? The two large spin-on filters are upside down, so i can just drop them. Anyway, just not sure about how or if to change all that oil (dunno if the p.steering fluid mixes with the rest of the tranny..) ~
@LawnGardenFun
Жыл бұрын
Thanks. I’m not sure about your ps vs rest of fluid but I would imagine it’s all part of hydraulic system. Does your manual say anything about ps fluid or how to change? Thanks for watching!!!
@georgehofgren6123
Жыл бұрын
@LawnGardenFun I bought mine second hand... didn't get a manua unfortunately. But maybe i should contact Simplicity and ask them instead of Tufftorq... 🤔 Thanks for the idea 💡
@LawnGardenFun
Жыл бұрын
@@georgehofgren6123 Yes, the manual is available on the simplicity website. Just use the model #.
@georgehofgren6123
Жыл бұрын
@@LawnGardenFun Thank you ~
@idtm77163 жыл бұрын
Nice job thank-you
@LawnGardenFun
3 жыл бұрын
Always nice to hear positive feedback. Thanks for watching!!!
@joshshaw65054 жыл бұрын
My grandfather was looking at that tractor and the Massey Ferguson version of that before agco solid the Massey line of garden tractors over to Briggs and Stratton then Briggs and Stratton bought simplicity and they discountinued the Massey Ferguson line
@LawnGardenFun
3 жыл бұрын
Thanks for sharing and watching!!!
@skirtdevil4 жыл бұрын
Hi,,I got a 22hp vandguard conquest,,,its a 50" mower ,,,,i need a hood,,,,,,do u know any other hoods that would work on my simplicity????,,,,,Thanks
@LawnGardenFun
3 жыл бұрын
No, sorry
@joepro88584 жыл бұрын
It would have been easier to drop the k66 out of the chassis and just roll it out rather than taking all that othe crap apart.
@LawnGardenFun
4 жыл бұрын
joe pro Yep, there’s plenty of merit to do it that way as well. Thanks for watching!!!
@vap0rtranz
Жыл бұрын
I just removed my K66 from the rear end. Still gotta undo all the linkages, and raise up the rear about 2+ feet, and it took awhile getting everything unbuttoned, so it's a toss up on which way is easier. BTW: don't just "drop the pan". I didn't do that but the trans rotated on me and one of the gearsets almost fell out with the bottom pan. That would not have been fun to put back together.
@roncoleman95022 жыл бұрын
Hey good video I'm in the process of I was thinking adding transportation fluid to mine but after what you did I might change my mind. Mine in the first 15 to 20 minutes mine will take off down the hill and I can't hardly stop it. Do you think that will help? Thanks for what you do
@LawnGardenFun
2 жыл бұрын
I would go ahead and change out the transmission oil and see what happens. Thanks for watching!!!
@roncoleman9502
2 жыл бұрын
@@LawnGardenFun thank you my friend I will subscribe because you answered to me. I really wasn't expecting you to answer me now you have a friend for life ha ha. Thank you again
@LawnGardenFun
2 жыл бұрын
@@roncoleman9502 You are very welcome "my friend" lol. Thanks for watching and subbing!!!
@lukeslegos78084 жыл бұрын
Hey bud, I wondering if drain and fill plug would be the same as my 12rt?
@LawnGardenFun
4 жыл бұрын
Lukes legos highly unlikely but not 100% sure. Thanks for watching!!!
@lukeslegos7808
4 жыл бұрын
@@LawnGardenFun ok, I was wondering why my transmission was getting to hot to touch, I also think its getting slower and weaker, could a oil change on my hydro fix that?
@Sully5400
3 жыл бұрын
@@lukeslegos7808 Yes, replace with synthetic oil and you might see increase in speed / strength.
@pyro3233 жыл бұрын
Is the fluid type and capacity the same for a broadmor 14? My brother was given an older Simplicity broadmor14 with a snowblower attachment and the gear box wines when it's engaged. And of course the back tires are dry rotted and the wheels are stuck on. 🇺🇲 👍
@LawnGardenFun
3 жыл бұрын
Manual says 10-30 Premium grade engine oil. 3.5 quarts. You can find the manual on Simplicity Manufacturing website. Model #1692279 Thanks for watching!!!
@pyro323
3 жыл бұрын
@@LawnGardenFun thank you! We didn't have the paper manual and there was no cell service where he lives.
@hockeysockeys53234 жыл бұрын
You still have the white gt
@LawnGardenFun
4 жыл бұрын
No sir. Thanks for watching!!!
@hockeysockeys5323
4 жыл бұрын
I was lookin to buy a white gt 1855
@rugby3874 Жыл бұрын
They shouldn't make it so difficult to change oil.
Пікірлер: 45
I have owned my Simplicity for over 15 years and it is the best riding mower I ever owned.
@LawnGardenFun
Жыл бұрын
Yes, they are pretty darn good!!!
Keith! First off, great to see a vid from ya and second, great to see ya tackle a transmission lol great vid my friend! I remember doing this on my Scotts and it really helped it, the fluid at a certain point must just really start to breakdown.
@LawnGardenFun
4 жыл бұрын
Thank you sir, greatly appreciated. It wasn't too bad of a job at all. Thanks for watching.
There are so few videos of the Conqeusts on youtube. I'm about to buy a '20 so I can be pampered because of my health. Wish more owner videos were out there. Thanks for yours.
@LawnGardenFun
4 жыл бұрын
You are welcome. Thanks for watching.
I’m process of doing exact thing. When u filled the oil did you fill to the top or leave some room from cap or ? I’d greatly appreciate it
@LawnGardenFun
2 жыл бұрын
I believe if I remember correctly you fill to top of the chamber not all the way up the neck. Thanks for watching!!!
@whatifyourwrong9153
2 жыл бұрын
Liked and subscribed thank you for the reply
Hi, I had the same problem. My conquest would'nt climb while cutting grass even on a slight incline. I'm sure I emptied out the wrong oil which was black in color by removing the front internal transmission filter. They filter was missing (fig. 17 page 20 of the manual). I then proceeded to fill in the hydraulic system from plug B in figure 16. Did I fill the oil into the wrong plug?. I think maybe I should have filled the expansion bottle with the oil instead. Did I make a mistake? Thanks for your advice. Mario
@LawnGardenFun
3 жыл бұрын
You should fill both chambers and then also put a small amount in the expansion bottle too.
@LawnGardenFun
3 жыл бұрын
Thanks for watching!!!
@mariolmarini
3 жыл бұрын
Thanks for the advice...
Great video, thanks. My Conquest (2011) has power steering, so two lines come off the Trans and pass thru two large filters, then go to the steering valve and to the cylinder @ the wheels. So, I would imagine i have quite a bit more fluid... Any ideas on changing that accessory oil? The two large spin-on filters are upside down, so i can just drop them. Anyway, just not sure about how or if to change all that oil (dunno if the p.steering fluid mixes with the rest of the tranny..) ~
@LawnGardenFun
Жыл бұрын
Thanks. I’m not sure about your ps vs rest of fluid but I would imagine it’s all part of hydraulic system. Does your manual say anything about ps fluid or how to change? Thanks for watching!!!
@georgehofgren6123
Жыл бұрын
@LawnGardenFun I bought mine second hand... didn't get a manua unfortunately. But maybe i should contact Simplicity and ask them instead of Tufftorq... 🤔 Thanks for the idea 💡
@LawnGardenFun
Жыл бұрын
@@georgehofgren6123 Yes, the manual is available on the simplicity website. Just use the model #.
@georgehofgren6123
Жыл бұрын
@@LawnGardenFun Thank you ~
Nice job thank-you
@LawnGardenFun
3 жыл бұрын
Always nice to hear positive feedback. Thanks for watching!!!
My grandfather was looking at that tractor and the Massey Ferguson version of that before agco solid the Massey line of garden tractors over to Briggs and Stratton then Briggs and Stratton bought simplicity and they discountinued the Massey Ferguson line
@LawnGardenFun
3 жыл бұрын
Thanks for sharing and watching!!!
Hi,,I got a 22hp vandguard conquest,,,its a 50" mower ,,,,i need a hood,,,,,,do u know any other hoods that would work on my simplicity????,,,,,Thanks
@LawnGardenFun
3 жыл бұрын
No, sorry
It would have been easier to drop the k66 out of the chassis and just roll it out rather than taking all that othe crap apart.
@LawnGardenFun
4 жыл бұрын
joe pro Yep, there’s plenty of merit to do it that way as well. Thanks for watching!!!
@vap0rtranz
Жыл бұрын
I just removed my K66 from the rear end. Still gotta undo all the linkages, and raise up the rear about 2+ feet, and it took awhile getting everything unbuttoned, so it's a toss up on which way is easier. BTW: don't just "drop the pan". I didn't do that but the trans rotated on me and one of the gearsets almost fell out with the bottom pan. That would not have been fun to put back together.
Hey good video I'm in the process of I was thinking adding transportation fluid to mine but after what you did I might change my mind. Mine in the first 15 to 20 minutes mine will take off down the hill and I can't hardly stop it. Do you think that will help? Thanks for what you do
@LawnGardenFun
2 жыл бұрын
I would go ahead and change out the transmission oil and see what happens. Thanks for watching!!!
@roncoleman9502
2 жыл бұрын
@@LawnGardenFun thank you my friend I will subscribe because you answered to me. I really wasn't expecting you to answer me now you have a friend for life ha ha. Thank you again
@LawnGardenFun
2 жыл бұрын
@@roncoleman9502 You are very welcome "my friend" lol. Thanks for watching and subbing!!!
Hey bud, I wondering if drain and fill plug would be the same as my 12rt?
@LawnGardenFun
4 жыл бұрын
Lukes legos highly unlikely but not 100% sure. Thanks for watching!!!
@lukeslegos7808
4 жыл бұрын
@@LawnGardenFun ok, I was wondering why my transmission was getting to hot to touch, I also think its getting slower and weaker, could a oil change on my hydro fix that?
@Sully5400
3 жыл бұрын
@@lukeslegos7808 Yes, replace with synthetic oil and you might see increase in speed / strength.
Is the fluid type and capacity the same for a broadmor 14? My brother was given an older Simplicity broadmor14 with a snowblower attachment and the gear box wines when it's engaged. And of course the back tires are dry rotted and the wheels are stuck on. 🇺🇲 👍
@LawnGardenFun
3 жыл бұрын
Manual says 10-30 Premium grade engine oil. 3.5 quarts. You can find the manual on Simplicity Manufacturing website. Model #1692279 Thanks for watching!!!
@pyro323
3 жыл бұрын
@@LawnGardenFun thank you! We didn't have the paper manual and there was no cell service where he lives.
You still have the white gt
@LawnGardenFun
4 жыл бұрын
No sir. Thanks for watching!!!
@hockeysockeys5323
4 жыл бұрын
I was lookin to buy a white gt 1855
They shouldn't make it so difficult to change oil.
@LawnGardenFun
Жыл бұрын
Totally agree. Thanks for watching!!!