Simple Water Level Indicator Without IC & Transistor Using
Ғылым және технология
Hi Friends,Today In This Video Have Shown How To Make Simple Water Level Indicator Without IC & Transistor Using
Part list
Green led 3
Red led 2
100 Ohms Resistor 5
Battery clip 1
9v battery 1
If You Have Enjoyed This Video Then Pleas Like,Share,Comment And Don't Forget To Subscribe Follow us on:
Website : techsawco.com/
Twitter: / techsaw2
**********************************************
#Techsaw #WaterLevelIndicator
Пікірлер: 349
Due to corrosion on the sensor points( due to high current flow) such circuits are not recommended, rather use Microcontroller/OpAmp based circuits where very low current flows through the sensor lines.
@peterfitzpatrick7032
5 жыл бұрын
....or use stainless steel ... 🙄😒
@noahmeurer7002
5 жыл бұрын
@@peterfitzpatrick7032 That's okay if you want to stop the corrosion. However, when you add salt to the water to increase it's conductivity and then apply a current, you split NaCl to Na and Cl. And - maybe you guessed it - get chlorine gas. Which is not really great due to its poisoness. Using a proper circuit is definetly a better option.
@muttley1956
5 жыл бұрын
Vijaykumar Malthane If only you knew what you are talking about.
@dmna7609
4 жыл бұрын
@@noahmeurer7002 it doesnt split the NaCl, it seperates the hydrogen from oxygen. Just like a hydrogen fuel cell. The more current flow, the more hydrogen oxygen gas.
@kamalbihan3012
4 жыл бұрын
Bhai uski janaga lead laga do
Simple yet successful project.!!
I like the idea of the 2 red LEDs indicating that the tank is full it works nicely for a motorhome so you can attached the sensor for the red LEDs to indicate when the tank is to full for the vehicle capacity
@rumenivanovtzonchev4072
Жыл бұрын
After 1 month due to electrolysis, the exposed parts of the wires will dissolve in the water and disappear. Why do you lie to people?
you can see electrolysis occurring at your anode due to the relatively high current needed to drive the LED. Transistors are cheap and the gate current necessary is much lower.
@kavitasuthar6155
2 жыл бұрын
kzread.info/dash/bejne/e3x4rdKAmdGYfLw.html Here u can go
very nice . God help you in evry feild. Thanks Dear.
Proof of concept. How much salt did you put on the water?
@newtechnicianpc2newtechnic413
5 жыл бұрын
Dekhiye sir salt add karneme Kam easy ho hate hai but mere chanel ko ap follow kijiye Mai normal water se Kam Kiya hu. #technicianpc chanel subscribe please
@md.saphiahamad5882
4 жыл бұрын
Salt ka kya chakkar hai bhai
@punkaj
3 жыл бұрын
There is no need of adding salt, regular water has enough ions already.
Like your ideas. Some are very good for science projects but not the "cap spot welder " !
love this mini project. thanks for sharing 🎉
Igen, ez az első, ami az ember eszébe jut. De így az oxidáció megeszi az elemet, a vezetéket és a forrasztást.
Awesome video thanks you for inspiration
Hi, very simple and looks effective way to detect the water level. Just a query, have seen other videos too and others have used transistors where I dont see that in ur video? Is it mandatory or what is the use of transistors?
@ElectrotechysMedia
2 жыл бұрын
Yes its mandatory to use transistor. A transistor provides proper biasing voltages to switch its load from its high sensitive base terminals. Also note that water is not a good conductor of electricity. So if we directly place wires voltage will be lost in the form of high resistance, to drive directly an led its not sufficient .if we put some salt in water conductivity increases.
@kavitasuthar6155
2 жыл бұрын
kzread.info/dash/bejne/e3x4rdKAmdGYfLw.html Here u can go for all answers If u like plz subscribe🤗
@merigeeth
Жыл бұрын
@@ElectrotechysMedia I made a device with some DC connected LED indicators to know water level of Ground Tank. A simple device, power supply leads negative to bottom of Water Tank and different levels set at 4 leads and will be connected through raising water levels. All my test with LED indicators and power supply was good before the installation and glowing according to Water Level. But when installed, instead of specific LEDs to glow according to water level, all the indicators are glowing. What is the reason please ? Any diode to be connected.. No idea?
Ciao secondo te posso usare una batteria da auto a 12v e dei cavi di rame lunghi 20 mt??? Mi serve per vedere i livelli di acqua del pozzo. Grazie ciao
Hi, Good info. correct me if i am wrong. Here water is conductor ? if water is conductor and used for real time application(water tank), current will pass whole water from bottom to top. After long use battery will drain past. right ?
It works if the water with salt (salz ملح)
@minoru2878
5 жыл бұрын
Or mineral water or with shampoo or soap
@newinnovation8938
5 жыл бұрын
#technicianpc chanel subscribe please
@_shayrishorts
3 жыл бұрын
It can also work in the general water or tape water
@officialhackersking7371
3 жыл бұрын
No its also work in tape water
Bhai bahut acha ye project bahut easy hai
Notice the oxygen coming off the negative black wire end. It will corrode away fast. But it could be used with a switch to check occasionally, and most of the time it will be off.
@newinnovation8938
5 жыл бұрын
#technicianpc chanel subscribe please
@weltonrodriguesaguiar1790
10 ай бұрын
Exatamente fiz desse jeito da muito problema!! Vou coloca um interruptor de boia
Muito bom!! João from Brazil
Hello. Congratulations on the project. Very simple. I would like to know if you can connect with 12v?
@wahyupuspitasari4509
4 ай бұрын
Up
Can it be used for something other than water, for example, for car fuel and oils?
this is amazing for kids, i did it and at the top i just used a buzer and a bc547 to sound when its full
How can some normal water transmit that much power without any chemical composition??
@newtechnicianpc2newtechnic413
5 жыл бұрын
In laboratory water means H২O no transmit electric . If some material added (salt) it's work easy.dekhiye panime khanij nun rahite ha uske sath acid ya khar hota hai isliye। Ye Kam karta hai, #technicianpc chanel subscribe please
Bread boardil connectn cheyyamo
In the water you mixed some pics of solt
@newtechnicianpc2newtechnic413
5 жыл бұрын
Dekhiye salt na mixed karke vi e Kam katega up mere chanel ko follow Kare #technicianpc chanel subscribe please
Nice idea... long does the battery last and what’s the minimum length of the wire it supports
@BELLACRAFTSANDTEC
4 жыл бұрын
kzread.info/dash/bejne/apqIusGqZ6XHfqg.html 6 meter wire
@kavitasuthar6155
2 жыл бұрын
kzread.info/dash/bejne/e3x4rdKAmdGYfLw.html
Is that salt water
Can u tell me which video editor do u use plzzzzzzzz..... Tell meee plzzzz
thanjs for u learn video, but if this use fortankhome about healthy notbad yes ?
Will this work on 12 volts as well?
very good video... I have some questions: 1) can you leave the 24 hours connected to a source of 220v to 9v...? or would the leds burn out? 2) Can you add a buzzer to sound the 3rd led due to low water? what piece and where should it be connected? I await your reply. Thank you
@Techsaw
Жыл бұрын
Please see our latest video
Empleado transistores para cada led es posible que funcione con agua destilada.
@greenreader1
5 жыл бұрын
El agua destilada no es conductora de la electricidad.
@luiguipantoledo4301
5 жыл бұрын
Lo sé pero su resistencia no es infinita...con transistores MOSFET se consigue activar los LEDs.
What !! No arduino or micro-controller ?? 🙄😂😂😂 Nice job man... 😎👍☘
@RakibHasan-qt9gx
5 жыл бұрын
Peter Fitzpatrick টট
@peterfitzpatrick7032
5 жыл бұрын
@@RakibHasan-qt9gx ... not sure what that means but I'll take it as a compliment !! 🙄😂
Can i use it to chech level of gasoline or its dangerous
@ianmclellan8514
5 жыл бұрын
This will ignite your gasoline for sure, if even a little bit of air gets into your tank.
@drlowbatt609
5 жыл бұрын
It will not work. No electric conduction with gazoline. Fire danger are low, but exists.
Buenisimo gracias y saludos desde Colima Mexico
Ser agar mujhe mobile charging se conact karna ho to yahi register lagange ya aur koi
If used on drinking water tank, will one be electrified when turning faucet on?
@madhavanmarikani5002
3 жыл бұрын
Bro , DC is used in this circuit .So , no problem
Do you any circuit diagram when tank water goes half empty the red led light up
@karunalatchoumy6182
3 жыл бұрын
This project shows u there are 5 levels .u can divide the tank height into 5 levels one level is 20% second level 40 % and so on .the led light "on " condition show u how much percentage of water is there in the tank. For example three led 's are glowing then 60%water present in the tank.
Ye jada pani me kam nehi karta Sp pani me namak milaye ho
@ayushnishad8573
5 жыл бұрын
12volt ka battery laga
@TARIFKHAN-fd6tt
5 жыл бұрын
yes thik vola
Very good 👍
Petrol tank mein install karne par koi problem to nahin hoga Na
El líquido empleado debe tener baja resistencia de lo contrario no creo que funcione. Seguramente están usando solución con sal.
better idea will be use only one resistor on gmd
Good idea thank you
Can we add buzzer for alarm to this circuit?
Tem como fazer com a V menor como o carregador de celular?
exilent
can use it on a water tanker truck?? because truck have 24 volts body ground
Bendiciones. Ponga por favor lo que es en español
@Kenjiro25
4 жыл бұрын
lista de partes: Diodo emisor de luz color verde: 3 Diodo emisor de luz color rojo: 2 Resistencias con valor de 100 Ohms: 5 Clip para sujetar batería de 9 Voltios: 1 Batería de 9 Voltios: 1 Saludos :)
Some says it is supposed to be 220 ohm and it did worked. So, which is the correct one.
Thanks
Est ce que ça va fonctionner dans une cuve de 10 000 litres ?
Pretty simple but looks good
Can I use 220 ohm resistor...?what will be the difference in using 100 Ohm and 220 ohm?
@lilafloresu.5558
3 жыл бұрын
the led is brighter with a lower resistor
Thanku so much sir ..plz ap yh btaynge ki kya isme battry ko power suply nhi di apne ??..plzzzzzzzzzz its urgent mera project h plzzz
@solarplusenergy2026
4 жыл бұрын
Battery to khud Powe supply karti hai. But wo new ho tab hi. Used battery nahi. Agar koi mobile charger ho to uska bhi use kar sakte hai
@mokimsk
4 жыл бұрын
Bc547
I made mine and have tested it and it is fully functional, I will probably install it tomorrow, thanks a lot!
@cesarcardenas9492
3 жыл бұрын
El cable rojo del broche de pila se mete al agua
@nanikhachi338
2 жыл бұрын
How to check led + - side ?
@orlandobaez2321
2 жыл бұрын
@@nanikhachi338 watch the video again, when show the green LED, you will see it.
@orlandobaez2321
2 жыл бұрын
@@cesarcardenas9492así es, así se cumple el circuito y puede llegar la energía.
Brother fuel tank k liye use ho skti h petrol ki wja sy koi problem ?
@vijayrajkundapur3518
3 жыл бұрын
Sure it's dangerous for fuel tank .pls don't try
Without salt ya kam nahi karta
Please tell me..! YaE btye resistance ; bulb; wire ye sb samaan ka kiss shop pr milega i mean kisae shop pr milega
@KumarSandaTV
5 жыл бұрын
Electric, electronic shop per milenge This project value just 10 rupees #technicalsmile
@alexsibomana4325
3 жыл бұрын
Hello sir can you will send me the power circuit and control circuit
Sir can we use this method for 12v battery
This will have electroplating effect and metal ions are released in water.
What is the of the wire to be use, can it lights if I use 6ft long wire?
Thats works on the gas tank?
Kaya ya system 12 volt ma chala ga or is ma salt dalna zrori ha kaya
Can it be used in home water tank?
very nice
Good bro
Very nice
What to do if we have to add a buzzer also when the tank is full
@newinnovation8938
5 жыл бұрын
#technicianpc chanel subscribe please
@rajsinha7934
4 жыл бұрын
Ye light bahut kam deta hai bro
Saludos.. Puefed hacer un pide vias led... Como para uns moto... Y que todocircuitos de bajo consumo
will it work in petrol?
@BHASKAR10761
5 жыл бұрын
😂😂
@newinnovation8938
5 жыл бұрын
Ag lag jayega sir
Thank u
AWESOME
It's work nicely 👍👍👍👍
nice
As I made twice.. But not working after some days led goes fault as per my thinking resistance value should change accordingly bottom to top.. Be if first led glows than more voltage is going that's the reason
@adityachaudhary6655
2 жыл бұрын
Bro it's not working properly because pure water is not a good conductor of electricity. For electrical conductivity , we need ions in water.. we can add salt to increase electrical conductivity. This circuit only works with salty water or we can say ionised water...But for pure water, we have to add transistors to the circuit. Talking about resistor..apply Kirchoff voltage law..then you can easily calculate resistor value for led
Nice
Can i use there 12volt or more?
Hola buenas bien trabajo y que ago si quiero agregar una bocina de alarma?
Mantap 👍👍👍👍👍
Hãy quá
Sir 4 light nahi jal raha hai light oms thik hai kiya kare 14 volteg de rahe hai pliz help pliz coment
Can it be used in motorcycle gas tank ?
@mersudinkevric4869
8 ай бұрын
did you tried to make one :)
Como hacer uno para nafta de tanque de moto?
@jaimealbertovelasquezramir1113
5 жыл бұрын
Ni lo intentes, seguro te va a hacer un incendio.
The wire will quickly corrode in the water
@muttley1956
5 жыл бұрын
featherbrain Please think before posting. Water is transported around our homes in copper pipes. They do not corrode. Copper is used to cover roofs etc because it doesn't corrode. Guess what most wires are made from?
Sir mai banaya magar tank mai pani khatam ho jane par bhi led light thodra thodra jal raha hai koi solution batayea thik karne ka.
how many ampiers needed for 2000L Tank?
@BELLACRAFTSANDTEC
4 жыл бұрын
kzread.info/dash/bejne/apqIusGqZ6XHfqg.html see this work with mobile charger
Inteligência humana p*** m**** muito inteligente
Bro water touching led brightness too low
How much we can extent the cable to water tank?
@Saifalipalla
5 жыл бұрын
As per my opinion use cat 6 wire less power consumption
Led कितने वोल्ट की लिए ho
How many volts does the LED use?
nice video
Постоянный ток не целесообразно использовать в устройстве такого типа так как он быстро разрушает електроды.
@victorhernandez3628
4 жыл бұрын
вероятно, если он используется только с электрическими импульсами, он работает лучше
Acho que o resultado está invertido. Red Low, Green Full.
It will also work without resisters
can i used mobile charger without battery ? pls tel me now, what can i do ?
@striejff964
4 жыл бұрын
😆
what if in the gasoline instead of water, is it possible?
Pls show for 4 story building overhaed tank water level.
@fidelcatsro6948
5 жыл бұрын
build 4 storey high leds and wires
Данную схему применять нельзя! Постоянный ток меняет структуру воды, растворяя в ней электроды! Вы можете получить проблему со здоровьем не зная причины болезни! Только переменный ток и специальные электроды для замера уровня. Но лучше используйте герконы!
can i use 3 volt battery for this water level indicator. please give reply sir
@garymucher9590
5 жыл бұрын
Sure can if you recalculate the resistor values to allow ~10 ma of current flow through the LEDs. In this circuit he is allowing ~90 ma flow which is a little high not counting the resistance via the water. A 300 ohm resister could work for 3 volts. Adjust for the brightness you desire. I.E. higher for less light, lower for more... JMHO
@fidelcatsro6948
5 жыл бұрын
gary @ 9volts he is only using 100ohm resistors, so how can you recommend 300ohm for something driven at only 3volts?
@garymucher9590
5 жыл бұрын
@@fidelcatsro6948 Because at 9 volts he is allowing 90 ma of current at 9 volts to teh LED. I can tell you that LED isn't going to be lit for long. Most LEDs work around 10 to 20 ma's. not 90 ma's. Understand?
@fidelcatsro6948
5 жыл бұрын
no way its using 90ma!! there is substantial resistance from the water
Very Very Nice Video