Stumbled across your video today. I'm the one who made those snap-on grips for the neutrona wand! Thank you very much for linking to our shop and the Cult3D link too!

@MADEbyAP

10 ай бұрын

That’s awesome! Thanks for making it. Holding strong and looks great!

I switched the molded wires on the 'damaged' part of the hose by cutting the mold off, and stuck real ones in. I took the cable sock off, and bought the type used in the movie. I painted the under wire. I painted the wire parts of the cyclotron using paused screen shots. The rest I left as is.

I also painted the cilindrical part with the warning sticker silver as well. Maybe a few other small changes, including the Alice frame were also done. I got my neutrona wand before they put the ones out with the orange tip.

@MADEbyAP

11 күн бұрын

The orange tip is the worst haha.

Very cool. I used a 3D printed bit for the front grip on the "wooden" bit and also cut off the back grip and used a 3D printed grip there as well. Covered both in black hockey tape too. I need to replace those clamps, they look snazzy.

@MADEbyAP

9 ай бұрын

The clamps really take it up a notch for sure! Love that there are so many mods available to do on this!

Without the orange tip, everyone will think it can actually shoot a charged particle beam composed of protons.

@MADEbyAP

7 ай бұрын

😂 sadly true!

I was going to mod my Haslab, however, Spirit came out with their full sized GB1984 pack, so I will keep it stock and mod the less expensive pack instead.

@SirFunky

3 ай бұрын

shittier pack*

the only mod I intend to do, which is done, is a no-time out chip.

@MADEbyAP

6 ай бұрын

Yeah that’s one I need to do. An upgrade the power supply!

Excellent video. I was wondering if the cable that the yellow sleeve goes on the attaches to the cyclatron pull out or unscrew.

@MADEbyAP

7 ай бұрын

Thank you! So the end that plugs into the cyclotron just pulls out. The end that is attached to the actual pack though goes through a hole and then is attached somehow to the inside of the pack. You’d probably have to remove the backside of the pack to access it. Hope that helps!

@daviddyer1919

7 ай бұрын

@MADEbyAP it helps heaps mate. Thank you for taking the time to reply.

When cutting the soft fake wire loom to push the wires in is there anything to be careful of while cutting into it like real wiring for the pack.

@MADEbyAP

5 ай бұрын

Hi there, that section that I cut out, there's a hard plastic piece underneath that I believe protects the cables running to the pack. I'd suggest leaving that in and just pressure pushing your new wires in. Hope that helps! Check this section out: kzread.info/dash/bejne/fZ-Vxq-lfrjLeZM.htmlsi=Ut6Syc_c5LV_Vqi2&t=887

You used the stock screw for the cable clamp, right? What was the size of the washer you used?

@MADEbyAP

8 ай бұрын

Hi yes I reused the stock screw and the washer is actually 3/8”. Hope that helps!

@mcdixon

8 ай бұрын

@@MADEbyAP do you have a home depot link or something alike that I can use for reference? I've seen different types when I look one up.

@MADEbyAP

8 ай бұрын

Hi sorry I had turkey on my brain. The outer dimension was 3/8 but it’s actually an M4 washer. Try this link www.homedepot.com/p/Hillman-Stainless-Steel-Metric-Flat-Washer-M4-Screw-Size-4118/204801237

Will you be doing away with the 4D battery powersource? As that,s highly flawed

@MADEbyAP

11 ай бұрын

Probably. I actually am starting a new list of things to upgrade like adding the “always on” circuit and maybe adjusting some of the lights. There’s a part two in the future I’m sure haha.

@Sammo212

9 ай бұрын

it is super easy to do! I swapped mine out the other day and will eventually completely remove the plastic housing to cut down on the weight.

You remind me alil bit of Bruce Campbell you,ve got his nose but not his chin lols!

@MADEbyAP

11 ай бұрын

Lol amazing. One other person has told me that! I’ve also gotten Johnny Knoxville. Completely different ends of the spectrum haha.

@bedfordshiremodeller4491

11 ай бұрын

@@MADEbyAP I know lols!

@txag007

8 ай бұрын

I was thinking the same thing as watching his video!