Simple Arduino Energy Meter | Volt -Amp meter 20 Amp
Ғылым және технология
Hello friends, today in this video I've shown how to make an arduino energy meter which can measure current upto 20Amp.
Components used:-
1. Arduino Nano
2. 16/2 LCD Display
3. ACS712 Current Sensor (Using 20A)
4. 2.2K Resistor
5. 47K Resistor
6. 10K Potentiometer
For code and schematic click the link below
drive.google.com/drive/folder...
Пікірлер: 62
you are the best. thanks for sharing it👌👨🎓
Creative video, thanks for sharing it :)
By the way, great work sir
Excellent project
يعطيك الصحة والعافية ياهندسة
nice Volt -Amp meter 20 Amp0 nice work
Wow awesome ideas
Good, very good. :)
Good work sir Use this voltage 24v
Does it display real, or apparent power? Because if it's a simple code that just takes voltage and current and multiply them, it displays apparent power, which can be equal in case of resistive loads, but not for inductive or capacitive loads.
Excuse me, I also wanted to know up to what voltage and current can be applied to the input? Thanks.
Good👍
👍👍👍
Hocam merhabalar bu işlemi esp32 ve arduino nano kullanarak serial bağlayarak blynk ekranından ve 16x2 lcd ile yapabilirmisiniz? Lütfen simdiden tesekkur ederim.
goodjob.. my question is can I modified ready made volt-ampere meter 10A to 50A? if yes. how? thanks
It was a great videos. I want to measure current in microamps, what kind of circuit can i use.
TOP SEU PROJETO AMIGO. PARABÉNS. SÓ ME DIZ UMA COISA, É POSSÍVEL AUMENTAR O LIMITE DE CORRENTE E DE TENSÃO ?
what is the program U use to make a schematic simulation of the circuit ?
Wow
Is there a way to scale this project up to measuring power exceeding 500watts in a solar panal
Hie thanks for sharing, am planning to use this ... On the code there is delay(1000), would that interfere with other programs i will add running in the void loop()
Gracias
Hi, congratulations on the project! I made the circuit but the Ampere measurement is not exact (the measurement on the display is greater than about 2 Ampere), can it be calibrated and how? Thanks.
@Hello-nh3my
2 жыл бұрын
Using the trimmer pot to the correct voltage you seen in the correct source
Can we power it using single source?
what voltage can be measured?
Good
Same for 5amp current sensor? Please reply
Hello sir, I want to ask, what happens if when measuring the positive and negative voltage it reverses, will the Arduino be damaged?
How much voltage is it able to measure? I need to measure about 55V-60V. Will that work?
max volt? can test DC/AC?
Merhabalar bu projesi olduğu gibi esp8266 lolin ile uzaktan takip etmek için yapmaya çalıştım blyk uygulaması ile bir türlü yapamadım? Haberleşmenin sağlayamadım yardımcı olursanız çok sevinirim şimdiden çok teşekkürler.🙏
Hi i have a problem, it shows me 35v on display without acs712 connected to any source, is it chance that you know a solution?
What is this maximum voltage check
Hello what’s the role of pot please ?
Can u please tell connection of +5v
why not make for ac measurements
Tell us the connections of +5v also
mister, am a new student of electrical eng. a have a project to make a joulemeter to display efficiency of power in real time ( wh/m in real time ), efficiency in percent ( wh/total distance ), and the mileage. these are parameters of electric vehicle ( urban electric vehicle ), can u help me to make the joule meter? tysm, sorry if iam bothering u
Thank you very much Maximum voltage ?
@user-sh7dd7zn4o
2 жыл бұрын
Probably 25 volts
@Dailyoneminute1
2 жыл бұрын
Only 15volt
If i used arduino uno, is it still the same pin configuration from arduino nano?
@TechIdeasAG
Жыл бұрын
Yes
your high watage resistor is 5w but display shows 37 watts Why ???
Besteht die Möglichkeit, dass Du Dir die Hände wäschst, bevor Du das nächste Video machst? So schmutzige Hände sehen einfach unappetitlich aus. Danke Dir!
Maximum voltage?
@makinetasarm8694
Жыл бұрын
.
Can we add Arduino UNO in place of nano
@Dinesh-Bhardwaj
10 ай бұрын
Absolutely
can we use arduino uno in it ?
@TechIdeasAG
2 жыл бұрын
Yes, ofcourse
@muneeshkhurana8314
2 жыл бұрын
@@TechIdeasAG i have 16*2 LCD screen with I2C adapter for it , how to connect it , it has 4 output pins as gnd, vcc , sda and scl , how to connect it
why is there a 10k pot?
@mathsmadesimple556
Ай бұрын
To adjust contrast
Where to download code sir
@TechIdeasAG
3 ай бұрын
Given in the description
You’re obviously very smart. But instead of porn music, like mama said, *USE YOUR WORDS* _Descriptions would be _*_WAY_*_ better._
The code is not showing up. Any solutions/suggestions?
@tolotolo6192
6 ай бұрын
You have to be on a computer
@tolotolo6192
6 ай бұрын
it does not work on the phone
Atleast enable your video to be downloaded