Holy shit bro want some tub with that caulk

@jasonyurrrr9994

8 ай бұрын

Better safe than sorry you broke boi

@Tatoebot

7 ай бұрын

@@jasonyurrrr9994lmfao to much can cause it to dry on the inside not the outside clown then it peels

@nahhh5318

6 ай бұрын

You make a video and let's see you do it then

@nahhh5318

6 ай бұрын

​@@TatoebotWho cares what direction it cutest it fkn vinyl or silicone based, still gonna turn solid at some point, guess what it's also going to shrink because it's how these products act captain obvious

@Tatoebot

6 ай бұрын

@@nahhh5318 I have dummy

Takes a multi tool and notch the back of the goboard to sit flat on pan. Caulk it before tile and after tile.

@Tatoebot

7 ай бұрын

I honestly have seen this “teacher “ do it differently ever single time lmao. It’s unreal how I’ll be watch his video thinking yes finally you did it correct then he goes and does it all wrong again. He refuses to take criticism and advice because hey teacher are always right huh 🤔

@smokingnuns

7 ай бұрын

I've seen some pan manufacturers instructions that say to do it his way. Important to follow for warranty.

When you installed the board on top of the flange, why didn’t you leave a 1/4 inch gap between the flange and board for expansion? Is it not necessary?

Isn’t the idea of using Kerdi band to have the overlap 2+inches above and below the seam? Kind of defeats the purpose of applying it like drywall tape

@timothywhieldon1971

7 ай бұрын

nothing this guy does is good or correct

@Hill-J

7 ай бұрын

It’s overlapping the tray

@tonyc7090

6 ай бұрын

Complete waste. There's a flange on the shower base already.

@timothywhieldon1971

6 ай бұрын

@@tonyc7090 this hack idiot guy has no clue why he does things, he has been sued many times before and he makes bad videos on purpose because he makes more $ doing this and us commenting on it than actually doing good work.

@chrismacleod9326

6 ай бұрын

Yes that’s the idea but he put the band just as an extra measure. Not sure why folks are getting excited over a little bit of overkill.

Since you set the GoBoard directly on the flange, you don’t need the 1/8th inch gap?

All these tile vids when they install whatever tile backer material of choice, no one mentions the shim out needed on the studs to compensate for the thickness of the tub/shower base.

@kaseyc5078

Жыл бұрын

Not needed if you place it on top of the tub lip like in this video

@spo1386

Жыл бұрын

Not needed if you notice the back of the board. This method is all for nothing.

@robertopics

Жыл бұрын

From what I've heard about the go board® is that you can wet shim it

@Tatoebot

7 ай бұрын

No then your sheet rock doesn’t match up at the end of the tile …..

@travisdoe4663

7 ай бұрын

Your tile backer does not go over the flange,It butts into the flange otherwise you're Tilebacker will be setting in water all the time and will wicked moisture to your framing. It should be sittin a little less than flush with the sheetrock to Leave room for the thin set And a little Fatter than the flange so That your tile will go over the tile backer, over the flange And over the sheetrock On the edges. And seal that little gap between the back of the tile and the tub flange With a 100% waterproof sealer, not silicone.

What did you put up on the walls after?

Steve, I just want to clarify something. In previous videos where you used GoBoard and their sealant, you never used Kerdi band and Kerdi sealant around the flange. I actually did my bathroom like that but now I see you adding the Kerdi stuff to it and makes me wonder which way is better.

@BathroomRemodelingTeacher

10 ай бұрын

Just another way to do it. Sheet membrane would be a stronger way to go. But either way is acceptable 👍

@bubunelu7027

10 ай бұрын

@@BathroomRemodelingTeacher good to hear because there's nothing I can do now, bathroom is all done and I hope I did everything right, like I saw you doing it. I will keep this in mind when I do the downstairs bathroom that actually has a shower pan now. Not sure though that I will go with a shower pan or a mud bed/tile 🙏

@ivettesantana4319

5 ай бұрын

i was wondering this too. i am glad you asked and he answered. Kerdi is too much $$$

@cindyspicer5137

5 ай бұрын

Did you do two layers of the kerdi is what I’m wondering. It looked like you went over it twice it not sure

50% Caulk 50% Shower pan.

Do you ever line the floorpans so tile , mastic, grouting causes damage….

Ohh nice board above tub flange 👍👍👍👍

You need a two inch overlap with that membrane.

It's all that thick caulking necessary? Seems to me thinset and the band will be enough.

What thin set did you use?

Doubt that kerdi band will adhere to plastic/fiberglass whatever pan that is… I would have put kerdi pan down

I needed this

Ok you didn't even show how the sealant band sets on top of the pan. A closer look at what the job/video is about would be helpful.

@stillmatic03

Жыл бұрын

It’s a KZread short to draw interest to his actual videos

Thank you for sharing.

Holly Molly Batman! Looks like me after a date with a beautiful woman and she asks me to come home with her!😂

I usually use tar paper and masking tape on all my installs, works just fine

@billhamilton7524

9 күн бұрын

HUH,,,what are you talking about

Steve, just curious about the choice of using a steel base. Is that what you are doing exclusively now. ?

@timjilman3295

7 ай бұрын

That's an acrylic base, steel bases don't have flanges that tall.

Technicality there is still a micro sized gap between the kurdi band and the base.. and only the caulked in sealant is doing the waterproofing. So you could just do the sealant and it would be the same result. Definitely as many here as already have said this kurdi step is not needed.

@gladbandanna

Жыл бұрын

Can you help me understand? If/When water gets behind the tile from above, wouldn't it shed over the kerdiband instead of into the caulk and up the cement board?

@GenesisG70LaunchEdition

Жыл бұрын

Better to overkill shit like this… as a homeowner now that’s been through 2 leaks and probably close to $60,000 in damage and fixing… I would much appreciate the overkill… fuck do it 3 times over!! I’ll pay the cost to know my shit isn’t leaking!!

@customsolutions7167

Жыл бұрын

As a remodeler I can tell you the real problem with showers leaking it mostly the structure and framing and possibly settling of the house... These things shift or move the subfloor or framing around the shower slightly.. and cause the cracks and failure of grout etc...and that's where the leak is... If the structure is very solid and good thick subfloor plywood is used and fastened correctly .. then simple cement board and tile with grout can last longer than you will live...

@customsolutions7167

Жыл бұрын

@@gladbandanna water should not get in above the top of the tile that should also be caulked.. or tile up to the ceiling is what I do.

@customsolutions7167

Жыл бұрын

@@GenesisG70LaunchEdition you are in a very small minority of people who will go thru the expense to do that. There is nothing wrong with overkill if you want it and will pay for it. I have an engineering degree, and always over kill the jobs I do. But for a shower if framing and flooring all strong and secure you should be good without kerdi... Just like you can wear a mask out everyday for the rest of you life if you want to is overkill.

The Master Blaster

very profesional and efection

Thats one way looking great bruh 👌 😎 😅

When I install a shower or tub, I notch the studs to bring them flush. But I see the point if the pan is already installed by plumber.

@travisdoe4663

7 ай бұрын

Why would you want it flush? the tile backer should not be going over the flange. You only notch or shim the studs out if it's getting sheet rocked over the edge of a pre-made surround.

Schluter factory certified installer and taught to lao bottom to top with Kerdi. Pan to ceiling.

But why do that? Water is never going to puddle up that high it's going run over the curb first and if water is just able to soak through the tile/grout and penetrate through the crack between the go board and pan there are way bigger issues

so why not use the go board waterproofing sheet instead of the kirdi

Like using 3 extra safe Durex's.

I tube of 15 dollar a pop sealer per linear foot

Can you cut strips off your regular curry membrane to do this

Does the go board pro sealant harden after applied?

@spo1386

Жыл бұрын

No

Grind the back of board at flange area, silicone board edge to tub.

@timjilman3295

7 ай бұрын

No.

@nickfleming4757

2 ай бұрын

Yes that is now the recommended way for goboard.

Goboard is easy to just notch the back and have it drop over the flange.

@travisdoe4663

7 ай бұрын

You don't want it over the flange, that stuff will Wick moisture to your framing. It should be a little Thicker than the flange and the tile will go over the backer and the flange, then sealed the gap with a 100% waterproof sealer not silicone.

So is water really going to go up under there?

@racebannon5523

Жыл бұрын

it could if you hit it with a fire hose

@lobsterstrange

Жыл бұрын

@@racebannon5523 exactly sometimes I think all that is overkill

@MrDougiefresh69

Жыл бұрын

Yes if you’ve seen an old tub or shower demo and the corners are the weak spot and it always wicks up a couple inches maybe more, might as well waterproof that whole seam as much as these jobs are costing now a days you better dam well do it.

@racebannon5523

Жыл бұрын

Doug here doesn't know dick about squat Leave a gap between the tub or pan and the sheetrock and it won't Wick

The tile it’s going over hardie board. I don’t get it. Why would you use all that caulk. You have inch and a half flange. It’s not a tub.

My man’s rewriting how to tile

He is always pushing extra unnecessary supplies to get the job done.

Is red Devil good to use?

@RickinICT

Жыл бұрын

Sssshhh...they're not a sponsor.

Is the go board a green board substitute? For mold and water in the bathroom.

@kaseyc5078

Жыл бұрын

No it’s cement board

@kevingomez5722

Жыл бұрын

It’s a waterproof foam board for tile

@whattheschmidt

10 ай бұрын

​@kaseyc5078 it's not cement, it's foam, won't wick or absorb water at all.

@nohalo4me555

6 ай бұрын

If you are using green board you are building what a seasoned tile setter would call a "seven year" shower.

Thin set and mesh tape, let it dry then coat with hydraban or good topical waterproofing membrane. That’s the correct way. The kerdi technically still leaves a small gap at the bottom. Plus kerdi has been shown time and time again on multiple tests that it fails. The old ways that are tried and true never fail

@BathroomRemodelingTeacher

Жыл бұрын

Okay tile coach 😆 keep testing. How is hydroban the old ways anyways?

@Apexjasonmorganllc

Жыл бұрын

@@BathroomRemodelingTeacher testing would be using products that are known and proven to fail time and time again.

@robertopics

Жыл бұрын

​@@Apexjasonmorganllcplus o do not think that sealant or thin set are meant to be applied that thick.

@Apexjasonmorganllc

Жыл бұрын

@@robertopics depends on the thinset. Pro lite can be 3/4 thick

@MoneyManHolmes

Жыл бұрын

It’s not gonna leak with that goboard sealant holding it together! It’s not thinset.

How big of a mess do you want ? YES ... 😂😂😂😂

Im not so sure you can mix caulk with the cement and then apply the band like that ... What in the actual

Wow !😂😂😂

You see all kinds of things

This guy is nuts he's just a Salesman for all this waterproofing crap we've been doing wonderboard and thinset and mesh for 35-40 years with no problem no leaks this is a waste of time and a waste of money nonsense this water really travel up the wall behind the tile and then over the lip of the tub this guy is nuts and is he ever finish your job he works by himself it's crazy I throw him right out of my house

@MrDougiefresh69

Жыл бұрын

Yes water does do exactly that, don’t hate the player hate the game. Let me guess your the type that misses flip phones too.

@lucastudor5536

Жыл бұрын

It's ok for you because you just do the work quick and half assed then the next guy fixes your "work" when it ultimately fails in a few years. My company, and probably this guy, warrantees our work. As far as a waste of money, you don't buy the material in pieces you get whole rolls. So using shit that you already have and the extra 10 mins of your time is worth the homeowners and your piece of mind knowing that it's going to never have any water issues. At least half of the work we get is from repeat customers and their referrals. Going that extra mile, especially when it is something cheap or free, is what makes a happy customer which leads to them marketing for you for free.

here we go again 😅💘🤣💘 only the best will do brilliant ginus amezing talented caring professional skilled all the way is the American way

That's an overkill proces....

@johne8907

Жыл бұрын

Welcome to youtube 🤣🤣🤣

@jtc1091

Жыл бұрын

I agree ,Wasteful in materials and time. Just because you over do it doesn’t mean it’s any better.

This really feels redundant to me.

Why is the board set on top of the flange?

@Frazer20

Жыл бұрын

I wondered that. Seems like this is in the US where they may have different standards but in UK it’s board first then tray which is a more sound installation in my view

@jamrhein2

Жыл бұрын

Yea we do our pans direct to stud then drywall over the flange. Thats what the flange is for. It gives you something to nail to the stud as well as keeps water from running behind the drywall to the framing.

@evictioncarpentry2628

Жыл бұрын

So that water doesn't wick up if it gets behind

@Tilethoughts

Жыл бұрын

​@@Frazer20 doing it the way you described you'd have to rabbit tile or float walls.

@ocelot1979

10 ай бұрын

up to flange, tile is suppose to overlap flange slightly, leaving 1/8 gap for sealant

Seems overkill to me 🤷‍♂️ but hey ho each to there own 👍

@tcurr0309

7 ай бұрын

With water and mold is there any such thing as overkill ?

ReeeeeedddddddGuuuuuaaaarrrdddd!

pointless for the curb, also it calls for a v notch trowel and Kerdi specifically says it will void the warranty if you do not.

@danwatson9290

7 ай бұрын

Kurdi trowel is 1/8 square

@timothywhieldon1971

7 ай бұрын

@@danwatson9290 100% wrong, you are clueless. please stop. FROM kerdi's website DIRECTLY you are required to use a 1/4" x 3/16" (6 mm x 5 mm) V-notched trowel or the Schluter™-KERDI-TROWEL.... NOT an 1/8 v-notch is too small and will void the warranty.

One video you say to shim out the studs to bring the cement board down and not to install it atop the flange. Now you're doing the exact opposite. Don't forget to trowel on 5 gallons of RedGuard next 🤡

@BathroomRemodelingTeacher

7 ай бұрын

Mmm.. wonder if there’s more than one way to do things 🤔

no need to waterproof looks great but unnecessary

He was just talking shit about kerid

Approved by both manufacturers………not

Omg

Dude that horse was dead along time ago😳 I think the water is gonna stay out…

Terribly unnecessary

?

fiberglass showers only way to go. All this others tile technique is failure. No one does copper pans anymore. I see some 70 years old…no leaks.

any vapor barrier membrane should have been installed between the studs and the cement board.

@BathroomRemodelingTeacher

Жыл бұрын

Not cement board 👍

@racebannon5523

Жыл бұрын

even worse.

@BathroomRemodelingTeacher

Жыл бұрын

@@racebannon5523 yeah?

@racebannon5523

Жыл бұрын

​@@BathroomRemodelingTeacher yeah, the board shouldn't even be touching the pan. it goes above the lip.

@BathroomRemodelingTeacher

Жыл бұрын

@@racebannon5523 nothing to wick into foam my friend 👊

Wholly caulk! 🤦‍♂️

We have property in the states I guess we won’t be using u mate !! Good luck

That is the dumbest shit I’ve seen. I have never once in my life done this as a tile setter and have never had a tub surround leak. The flange is there to protect from water wicking up your wall. You literally made it worse doing this. Just tile it throw some silicone and it will be fine. Water won’t sit there long enough to damage anything

@BathroomRemodelingTeacher

5 ай бұрын

Look in the mirror 🪞

Really? A cheap acrylic shower pan, and improper manufacturer installation of Kerdi Band. V NOTCH . And Non Modified mortar. Watch some you tube to learn how to do it rather than have these people on that don’t any better think you actually know what you are doing. You can’t play Lincoln logs with Legos.

@BathroomRemodelingTeacher

7 ай бұрын

You are a special idiot. Thanks for commenting

Ew a synthetic pan

@j.w.r.i2910

Жыл бұрын

Y ew ?

@tcurr0309

7 ай бұрын

It's enamel clad steel shower base. I used one to cut down on all the grout cleaning of a tiled base.

Battery powered caulking gun?😂😂😂😂😂😂😂

Ey boy, back in my day I used to bite off the tip of the caulk with my teeth then squeeze the tube with nothin but my bare hands, boy! Take ya little toy gun back home and get off my jobsite!!

Gotta waterproof your waterproofing...😂😂😂

You are way over doing it !!!

That's like $300 in sealant

@MoneyManHolmes

Жыл бұрын

You could do what Tile Chick does. Cut a sliver off the back of the foam, slide it over the lip and set it into a normal size bead of sealant.

@edbrown7919

10 ай бұрын

It’s 9 bucks a tub probably only need 5 tubs

👎👎👎👎👎👎👎

Bloody hell ur kidding right ? This is a joke yeah mate ?

this guy is dedicated to excellency right on

Nope !!!!!!

Uhhh wtf

For being a tile guy you don’t know how to use a trowel

Waste of time and money

Sorry but a solid rubber membrane with no cuts is still the best .

you have no clue