I was away last week on a trip down south. Should I reuse the piston in the stihl 026.? Thanks for watching
Жүктеу.....
Пікірлер: 43
@MegaDirtyberty9 күн бұрын
I have cleaned up and reused worse pistons, even reused piston rings. I cleaned and reused a piston in my fs85 and it's still going years later. I have a 44.7mm piston I am going to reuse in my 026 (fitted with Caber rings). The bore clearances were the same as the brand new piston.
@martyrutter363010 күн бұрын
I bet your little girl missed her daddy something terrible. Glad you’re home safe and back in the groove. 👍👍
@tinmanssaws
10 күн бұрын
I missed her more I think
@thebradleysoncatbirdhill68499 күн бұрын
The best thing I have used so far for mosquitoes is cedar oil. I like the brand "Nantucket Spider". Keep swattin'!
@larrywarner931410 күн бұрын
Good day tinman, that bracket that the spring is hooked to I'd bend it so the spring lays away from the belt
@daveanderson246810 күн бұрын
Starting fluid and a lighter for the mosquitoes
@Magoot24569 күн бұрын
Good to have you back Tinman! I'm excited to see you port that 026, there are barely any videos on people porting them! I can't wait to see what a little monster you can build with one :) I've got an 026, and a partly built 026, both that I want to port, so this series has my full and undivided attention!!!!
@lanceevans68810 күн бұрын
Glad to see you back on the channel! Still monsoon season here in Minnesota as well. Trying to close on a house and the new septic is holding things up. I'm going to have my own shop. I'm super excited. Rain, rain, go away!
@kelvinpen314410 күн бұрын
If no damage to either cylinder or Piston then I would use it but I’m on tight budget and reuse a lot of things I work on 😎👍
@Fogyt1219 күн бұрын
A UV lamp with built in bugzapper might solve the problem, if you leave it overnight in the shop. I've seen one in action, it was having a field day.
@tomintexas81710 күн бұрын
Glad you made it home Houston Rough😮
@stanleymason815510 күн бұрын
The spring adjusts the tension automatically. If it's rubbing it's because the spring is barely stretched. Looks like belt is probably at least 2 sizes to long as the spring coils are about to touch. Been doing belts on all my own tractors lately.
@CraigArndt10 күн бұрын
Look at the size of those skeeters! Good lord. Like the ones I'd see up in Georgian Bay on fishing trips, carry you off. lol.
@aaronpowell488510 күн бұрын
Glad you had a great trip and thanks for sharing the inspection tips!
@billhacks9 күн бұрын
. Thats going to be an awesome saw when it's finished.
@tdawg860510 күн бұрын
Working on a walk behind mower at the moment as well and dodging the mosquitoes... they are to big to swat so you just walk around them....😂 was running a dodo coil the other day in the garage, it was the only way to have the garage door open. Can't go wrong with some Texas BBQ and sea food...mmmm. TC Mahalo Tinman 🤙🤙🤙
@christalbott844610 күн бұрын
Hope you catch up on home life!! Know the feeling to well! Another great video!
@andreaspapapetroy10 күн бұрын
Good evening from Greece, my brother, I am watching your channel, please put Greek subtitles.
@robertsimard7358 күн бұрын
Great tutorial. I have a few old pioneers p20 and a possible p41 that I may change the piston.
@alltherpm10 күн бұрын
I'm going through a homelite addiction, I've been adding ol blue xl12, and a 150 automatic, saws that my father used
@Righound410 күн бұрын
I would use that piston in the used cylinder for sure!
@davidbulich12548 күн бұрын
Yes would absolutely use it I've used worse and worked perfectly
@stevetheriault416410 күн бұрын
EVERYTHINGS BIG IN TEXAS ,,GLAD YOU HAD A GOODTIME BUDDY,, 😁👍👍
@jonathanhall13610 күн бұрын
Thanks buddy.
@Ecthelion_2nd10 күн бұрын
Good afternoon, Another good video as usual. I have tried widening the lower transfers on a MS260 to good results.
@scottwilson43969 күн бұрын
I like my rakers extra low for the sask gators Tinman 😂
@edwinhsingmaster913510 күн бұрын
Tinman and pistons, begs the question. Coating piston skirts.. I follow Wade,Ironhorse, Dyno, Buckin, Guilty, Donny, and never heard anyone mention it. What you say? Cheers from Oregon,USA. Hank
@larrywarner931410 күн бұрын
Now I'd keep that old piston cus you never know when you or someone else could use it in a pinch
@davidcarberry354710 күн бұрын
i hate mcskeeters , id heat it and bend it down, then no worries, nice piston all the mill marks are there, anyone lets there saw get that dirty dont blame the saw when it gives up
@5roundsrapid2639 күн бұрын
Put some 16:1 mix in an old saw with bad rings. Run that for a few minutes, no more mosquitoes! 😂
@timothybyrom55605 күн бұрын
I wouldn't. I love an 026,but they wear on the thrust side of the piston something awful. I'd use a new piston.
@timwatson452410 күн бұрын
I would go new the piston is cheep and good insurance
@tinmanssaws
10 күн бұрын
Yep I agree
@kurtsteele558710 күн бұрын
How's the Tinman and family
@ryanfriars545Күн бұрын
Buy a can of knock down (I believe that’s what it was called) Restaurants use it, although I wouldn’t advise breathing it in. Couple sprays around your shop/house/tent and the bugs will either lose interest or drop to the floor in 10-20 min. It works great. I always have a can of it for camping.
@clarencetrice444210 күн бұрын
HI TINMAN 😊😊 U have 2 get U a bug zapper 4 the bugs that we fix alot of them at night 🌃 😊 and when the yard holds water 💦 😮 that doesn't help none either the next 2 do is 2 get some good bug spray / the BBQ and Cole slaw is some kind of good that's the good eating 😊😅🎉😂❤😊 OMG 6 24 2O24
@justinweaver81077 күн бұрын
❤❤
@clarencetrice444210 күн бұрын
HI TINMAN 😊😊 some U can go 2 a place that works on small engines or some times a parts store and have a set of piston rings matched up IVE seen be 4 U have 2 use 2 rings 4 each piston groove if there's rings that aren't the width I seen that be 4 in a old engine a another fellow didn't know where 2 get the piston rings from and U can have custom piston rings made they make them 😊😊 OMG 6 24 2O24
@robert402710 күн бұрын
Tinman I want to ask how is the anti vibe on husky a 266 se. ? I might buy one but just not sure if it's ok for all day use
@tinmanssaws
10 күн бұрын
Its ok but nowhere near as good as the 372 saws.
@robert4027
10 күн бұрын
@@tinmanssaws awesome thanks very much sadly can't find any the 372 on Craigslist 100 miles radius ☹️
@justinweaver81077 күн бұрын
Id run that piston an cyl 4sure if its oem. Neither look bad 2 me
Пікірлер: 43
I have cleaned up and reused worse pistons, even reused piston rings. I cleaned and reused a piston in my fs85 and it's still going years later. I have a 44.7mm piston I am going to reuse in my 026 (fitted with Caber rings). The bore clearances were the same as the brand new piston.
I bet your little girl missed her daddy something terrible. Glad you’re home safe and back in the groove. 👍👍
@tinmanssaws
10 күн бұрын
I missed her more I think
The best thing I have used so far for mosquitoes is cedar oil. I like the brand "Nantucket Spider". Keep swattin'!
Good day tinman, that bracket that the spring is hooked to I'd bend it so the spring lays away from the belt
Starting fluid and a lighter for the mosquitoes
Good to have you back Tinman! I'm excited to see you port that 026, there are barely any videos on people porting them! I can't wait to see what a little monster you can build with one :) I've got an 026, and a partly built 026, both that I want to port, so this series has my full and undivided attention!!!!
Glad to see you back on the channel! Still monsoon season here in Minnesota as well. Trying to close on a house and the new septic is holding things up. I'm going to have my own shop. I'm super excited. Rain, rain, go away!
If no damage to either cylinder or Piston then I would use it but I’m on tight budget and reuse a lot of things I work on 😎👍
A UV lamp with built in bugzapper might solve the problem, if you leave it overnight in the shop. I've seen one in action, it was having a field day.
Glad you made it home Houston Rough😮
The spring adjusts the tension automatically. If it's rubbing it's because the spring is barely stretched. Looks like belt is probably at least 2 sizes to long as the spring coils are about to touch. Been doing belts on all my own tractors lately.
Look at the size of those skeeters! Good lord. Like the ones I'd see up in Georgian Bay on fishing trips, carry you off. lol.
Glad you had a great trip and thanks for sharing the inspection tips!
. Thats going to be an awesome saw when it's finished.
Working on a walk behind mower at the moment as well and dodging the mosquitoes... they are to big to swat so you just walk around them....😂 was running a dodo coil the other day in the garage, it was the only way to have the garage door open. Can't go wrong with some Texas BBQ and sea food...mmmm. TC Mahalo Tinman 🤙🤙🤙
Hope you catch up on home life!! Know the feeling to well! Another great video!
Good evening from Greece, my brother, I am watching your channel, please put Greek subtitles.
Great tutorial. I have a few old pioneers p20 and a possible p41 that I may change the piston.
I'm going through a homelite addiction, I've been adding ol blue xl12, and a 150 automatic, saws that my father used
I would use that piston in the used cylinder for sure!
Yes would absolutely use it I've used worse and worked perfectly
EVERYTHINGS BIG IN TEXAS ,,GLAD YOU HAD A GOODTIME BUDDY,, 😁👍👍
Thanks buddy.
Good afternoon, Another good video as usual. I have tried widening the lower transfers on a MS260 to good results.
I like my rakers extra low for the sask gators Tinman 😂
Tinman and pistons, begs the question. Coating piston skirts.. I follow Wade,Ironhorse, Dyno, Buckin, Guilty, Donny, and never heard anyone mention it. What you say? Cheers from Oregon,USA. Hank
Now I'd keep that old piston cus you never know when you or someone else could use it in a pinch
i hate mcskeeters , id heat it and bend it down, then no worries, nice piston all the mill marks are there, anyone lets there saw get that dirty dont blame the saw when it gives up
Put some 16:1 mix in an old saw with bad rings. Run that for a few minutes, no more mosquitoes! 😂
I wouldn't. I love an 026,but they wear on the thrust side of the piston something awful. I'd use a new piston.
I would go new the piston is cheep and good insurance
@tinmanssaws
10 күн бұрын
Yep I agree
How's the Tinman and family
Buy a can of knock down (I believe that’s what it was called) Restaurants use it, although I wouldn’t advise breathing it in. Couple sprays around your shop/house/tent and the bugs will either lose interest or drop to the floor in 10-20 min. It works great. I always have a can of it for camping.
HI TINMAN 😊😊 U have 2 get U a bug zapper 4 the bugs that we fix alot of them at night 🌃 😊 and when the yard holds water 💦 😮 that doesn't help none either the next 2 do is 2 get some good bug spray / the BBQ and Cole slaw is some kind of good that's the good eating 😊😅🎉😂❤😊 OMG 6 24 2O24
❤❤
HI TINMAN 😊😊 some U can go 2 a place that works on small engines or some times a parts store and have a set of piston rings matched up IVE seen be 4 U have 2 use 2 rings 4 each piston groove if there's rings that aren't the width I seen that be 4 in a old engine a another fellow didn't know where 2 get the piston rings from and U can have custom piston rings made they make them 😊😊 OMG 6 24 2O24
Tinman I want to ask how is the anti vibe on husky a 266 se. ? I might buy one but just not sure if it's ok for all day use
@tinmanssaws
10 күн бұрын
Its ok but nowhere near as good as the 372 saws.
@robert4027
10 күн бұрын
@@tinmanssaws awesome thanks very much sadly can't find any the 372 on Craigslist 100 miles radius ☹️
Id run that piston an cyl 4sure if its oem. Neither look bad 2 me