If you level the frets with relief you are removing the relief!! Absolutely correct to level with neck flat. As always there at exceptions to the rules.

@HighlineGuitars

2 жыл бұрын

Very true!

@MrSongwriter2

Жыл бұрын

I’ve watched a guy called Sam Deeks I think it is who basically uses a diy I think it was called the katana system. Basically it has a truss rod so say your fingerboard relief is 10’000 you set the level to the exact amount of relief as the board and it’s usually done with the strings on. I know he’s taken some significant flack for his none traditional method but he swears by it after hundreds of levels and refrets. I’m not going to say his method is right nor would I say it’s wrong, but I will say it goes against traditional methods. I also see as he is basically using a trussrod with abrasive paper the width is very narrow and I can see how he could easily do more under two strings than the adjacent strings. Therefor that is the issue I see vs a decent beam which does much more in one go on a perfectly flat board. Then run a fret rocker over it after to correct any outstanding problem areas. I tend to take Chris’s side, if a guitar he’s fretted and level and crowned is reported as no action needed on a pleck machine. I would still stick with the traditional methods. Sometimes you just don’t need to re invent the wheel just because you can

@chessbrothersnewy

11 ай бұрын

I had the same thought. So if you believe in some neck relief THEN you have to fret level in a flat state. If you can't adjust the neck anymore (for whatever reason) you may have to level in a non-flat state.

@chriswilliams1096

6 ай бұрын

Yes! What's the point in going to the trouble of creating some relief in the fretboard if you are just going to level the frets afterward? (I'm assuming that by "relief" we mean a tiny gap between string and fret (about fret 8) when caop'ing at fret 1 and holding string down at the highest fret.)

@chrissturley823

2 ай бұрын

I’m an amateur, so forgive my ignorance, but I thought the idea of relief was to kind of compensate for imperfection and allow the strings to play without buzzing. If you level your frets with the neck perfectly flat, then you should be able to set the guitar up and try to achieve a perfectly flat neck with no relief when the neck is under string tension. You wouldn’t need any relief at that point. Or is there another reason people would want relief? Do they want different spacing between the string and fret at different points on the neck? Does that make a difference in their playing style/technique or something? Again, forgive my ignorance. I’m just trying to learn.

Thank you for your insight! Sharing your knowledge really helps a new builder such as myself and is appreciated!

Great video! Very insightful and great to listen to as I am spicing up my PRS SE ! Thanks for your thoughts and for educating me!

Just found your channel. Just what I've been looking for! I hope your subscriptions continue to grow.

It is simple for me. The neck should be straight when leveling the frets. If you level the fret that gives the relief you actually play, there will be no relief on the fret even if there is a relief on the neck. This is nonsense, isn't it?

@hkguitar1984

5 жыл бұрын

Totally agree Hisashi SASAKI, the neck should be 100% straight when leveling the frets. Not even sure why this question is even asked as related to a full fret leveling procedure. Only reason I could ever imagine you would deviate from the accepted practice would be to remove a bit more fret material from the upper frets to possibly induce a "fall-off" with the upper frets having a touch more material removed to prevent "fretting-out" on the higher notes. The relief induced into the neck through the truss rod for normal playing setup maybe isn't as pronounced in the upper frets, thus the reason to sometimes using the "falling-off" of the upper frets. I guess I need to watch this video again, and maybe a third time to be clear of it's purpose.

@The6Stringbandit

3 жыл бұрын

Basic physics, the process of leveling indicates flatness or trueness on a certain length. You dont level a bow without affecting material removal

@jeffbosch1697

Ай бұрын

@@hkguitar1984 The upper frets are usually where the neck joins the body, so won't there will be zero bow there no matter the amount of relief?

@hkguitar1984

Ай бұрын

@@jeffbosch1697 Correct, on a single cut guitar the Bass side of the neck is glued in and making contact with the body (as a guess, up to the 14th Fret area). Often times the Truss Rod will only bow towards the end of the neck, but not always, designs differ, however I can't imagine the entire neck bowing. That said, it doesn't take much movement at all (bow) to greatly change how the guitar performs and feels to the Player.

Thank you Chris. I knew what you said was true but had doubts and thought about building a neck jig. You just saved me SO much time and headaches. Gonna keep leveling the same way as before- deadflat fretboard. Thanks Chris!!!

I am a tech, not yet a full-blown luthier, and in the last year have gotten heavy into fret work (fortunately with really good results so far). I was considering building or buying the Erlewine Neck Jig thinking it will increase my accuracy specifically in the leveling process; I have been leveling frets by setting the truss rod to a dead flat neck up to now. This video answered a lot of questions for me, and I think I will simply build a table to stabilize the guitar and neck while I work. Right now I rest the neck on a sand bag to stabilize. Thank you for your informative and engaging videos, and thank you for real talk about the many hype and industry induced mysteries surrounding guitar work, and showing us your real-world processes. Awesome Plek story too!

Thank you, great! This video answers all the questions I had about leveling with the jig and the plek machine. It encourages me to continue levling with an absolutely flat neck.

@HighlineGuitars

11 ай бұрын

Glad it was helpful!

Good Lord, your channel is an absolute goldmine of knowledge! Thank you, sir!

Thanks, Chris! I feel better about my simple methods in leveling the frets.

Chris, I found that most players don't know squat about the mechanics of their instrument. That's why we can make a living keeping their instruments in top playing condition. Luthiers use to trust their eye but now they need all the expensive tools because the tool salesman said so. Hell, for years I used an old credit card to check for a high fret!

@mrisaac638

2 жыл бұрын

hahahah I used credit cards!!!

@jordimateubartroli951

Ай бұрын

Yeah. I use cutter blades. You can break them at appropiate lenghts.

I subscribed because of the “bumper music”…. Heavy riffage!! Calming voice!!! This guy is dead level on point!!! YessssSir!!!!

I loved this video, for the same reason I like your other videos - you go in depth into the reasoning behind your thinking. That's extremely valuable. Too often, guitar youtubers give you their opinions on why something is right or wrong, but they don't explain why, or offer any kind of evidence. In your case, you offer the Plek machine as evidence that leveling the frets with a flat neck is probably the optimal approach.

This is my favorite luthier KZread channel by far. This guy is like the Wampler of the luthier world when in comes to knowledge for guitars.

I found your video very informative. Thank you for sharing.

Even if you want to level the frets under string tension, like on the Erlewine neck jig, you still have to adjust the truss rod for a straight neck. Before the advent of double action truss rods I used to built some relief into my necks. But would adjust them straight for leveling.

Excellent video mate I also level the frets with the neck flat then string the guitar up with the gauge of strings that will be used let it sit for a few days play it check again play it some more seems to work very well. I like my neck to be flat even under string tension not every one does some players like a small amount of relief. Love your Chanel mate have good good one!

Man what a great vid with great information!

A few years ago A friend and I built 2 neck jigs patterned after the StewMac one for our personal use as hobbyists. I've done refrets and dresses with and without the jig. The jigs we built weren't too difficult to set up and on an expensive guitar I'll use the jig; but while under string tension I keep the neck as flat as it will allow and when finished I'll use the truss rod for any relief. This was a very informative video. Keep up the good work:0)

Hi Chris, I see your point. The testing after-ward doesn't make a difference - because I think we would always test. But if we level "frets" when the neck is under tension, we take off more metal on some frets than necessary. To level frets while the neck is under tension, is to only use a truss-rod to keep the neck straight. Taking off more material than necessary renders the neck with less life-time. Truss-rods are for setting up necks. If you start with a level (straight) neck, you can work in the fall off if you want things like that to be factored. I prefer your method.

Leveling a neck with string tension (a bowed neck) makes no sense to me when your using a straight leveling beam. Personally I get the neck straight as possible and make sure the neck is well supported to prevent any flexing while leveling.

Great info, Thank you.Cheers.

Love your videos. So justified and clearly explained. I’d love to know your approach to straightening necks ready for a fret dress, where they won’t straighten properly.

That is a luthiers dream. Send it to the PLEK guys... "yeah, this guitar is already perfect"

@gaysquirrels6915

Ай бұрын

obsessive in my opinion, just play the guitar after the Luthier has done their tweaks and see if you like it lol

I know this is an older vid, but I'm still going through your backlog as they come up in my recommendations and I agree. I just finished my first complete refret of one of my own personal guitars (I got it used and it had lots of issues and not enough fret left to do a level). When I was done installing the frets I lad it in a neck rest and used a notched straight edge and a light behind it, looking at it from the side to check for spots where the light was coming through the bottom to get it as close to flat on its back and level as I could get it, then methodically did my leveling and it turned out great.

but if you level the frets with bow in the neck then you end up with all the frets level when the guitar is strung and that negates the point of having bow in the neck in the first place. the reason for putting bow in the neck is so that the strings can vibrate more freely, but the frets are the only part of the neck close enough to the strings to effect this, so having a bowed neck with completely levelled frets doesn't perform the required task.

I had to put relief into my neck when I went to light strings (9/42). Happy to hear about a better way around it :)

I am 64 now and have been playing bass and guitar since 1972...but I have never done this leveling myself. So I bought a Notched Straightedge for bass...a Maxparts BF-AF16 Fret File...a crowning file I had already, also understring radius gauges - and look forward to it like a little boy! That it is best to do this with an absolutely straight neck, I strongly suspected and now got confirmation. Thanks a lot! 🙂

hi, interesting point about different neck construction..i was taught to introduce a tiny backbow into the neck with the trussrod then clamp the body to the bench and put a wedge under the headstock.. push the wedge until the neck is straightish, then skim it. this way you replicate string tension and you also have a bit on truss rod for any future backbow problems. another way to replicate string tension is clamp the body to a bench( guitar fully strung and in tune ) gently put a wedge under the headstock and two wedges under the middle of neck , dont push the wedges tight, undo strings and skim..thats a way of replicating string tension without any fancy expensive machines or jigs.. ive worked for two different well known guitar manufactures.. one did it that way and the other did it your way..as you said, the way the neck is put together affects the strenghth and bendabilitity(new word)ha ha of the wood. for instance multilaminated necks.

I think you’re right on. You are a very interesting person to listen to. I love this video you give a lot of great information. Thanks so much appreciate it.👍🏼👍🏼👍🏼😁🎸❤️😁

Helpful. Thanks!

It SEEMS to me that slight relief lets you get lower action with less fret buzz because it ever so slightly changes the angle the string leaves the fret passing over the rest of the frets, but it also seems the lighter you play the less its necessary, harder playing induces a taller/fatter "football" of string vibration. At least that's my perception.

@Thecoolman1

2 жыл бұрын

Yea, i agree. I always have a lot of buzzing on my SG without any relief, I need around 8 thousands relief to have low action and no horrendous buzzing, still have a little though, but I can live with that

Thanks for the video. I've come to the same conclusion - level while the neck is flat. I have a neck jig, and I still use it, but with a slightly different aim: I first adjust the guitar's neck as straight as possible with the truss rod while the strings are on. Then, strap the guitar into the jig, zero the dials, bring the jack and rods up so they're supporting the neck. Then remove the strings. After the strings are off, there is usually some small adjusting that has to be done with the jack. But it's pretty easy getting the neck back to flat, rather than recreating some curve. I check with a straightedge that the neck is flat. The advantage to having the guitar in the jig while working is that it's super solidly mounted. I have the support rods up against the neck and they hold it flat all along the length. If you do not have the support rods up, you can actually see the dials moving by a few thousandths as you run a sanding block up and down the length of the neck, so I feel it's better to have the neck solidly supported all along. The other thing is that, on an older guitar, having the truss rod in a tightened position is a more accurate representation of the condition of the neck. Sometimes the truss tension does some weird things, like cause slight S curves (as viewed from the side). If you work in the jig, with the truss under tension, you can better compensate for these issues. So, I like working under truss rod tension, but on a flat neck.

I saw this video many years ago. Then now I really understand what you're talking about. And of course I agree with your point of view on this sensitive subject. After all, it takes some time... I guess. I'm really thank you.

I like the KISS method. Keep it simple and take all the rocket science out of it. This is exactly what you are doing with your videos. Thank you for making these videos.

Great advice! I've only levelled my guitars and a couple of other guitars for close friends, and I've only been doing this for a few years on and off, but also like you said about the bow being dependent on the wood type, I've also realised that there might be something in there to do with the tuning, string gauge and even type too! Since thicker strings in a higher tuning don't tend to have as much of a wide rotation as a thinner gauge in a similar tuning, so the area of bow becomes more important for guitarists who may use a certain guitar primarily for the same tuning with thinner gauge strings. I find on set necks/neck-thru guitars they tend to bow more often around the neck joint, which can cause issues for me since I use thinner gauge strings mostly, so I like to give the last few frets a TINY bit of a shelf just enough to give that area of the string room to rotate without buzz whilst keeping the action relatively low and even throughout the length of the board. Bolt-ons I don't usually have that issue with.

@HighlineGuitars

3 жыл бұрын

Set necks are also usually Mahogany and bolt on necks are usually Maple. Maple is less prone to string tension induced bow.

Totally agree,99% of the time leveling with a neck flat works perfectly fine, BUT very rarely you get a neck that doesn't behave evenly under string tension. Got a Yamaha BB5000(neck through 24frets) that without string tension, the frets were perfectly leveled. Once I strung it up to pitch , it got a bow between fret 2 and 9 and the rest of the neck was dead straight. Same with a Godin electric. What a headache trying explaining that to the customer. Maybe I should give it some more relief and call it a day. Malfunctioning trussrod? Uneven wood strength? Send it for PLEK treatment? I wouldn't even think of removing the ebony board of the Yamaha to replace the trussrod or add stiffening rods..

I agree with this approach also as level is level and straight is straight, especially on a new neck.

The purpose of relief is to allow space for the strings to vibrate freely along their entire length. Without it, the strings will buzz against the frets at the point on the neck where the first and second harmonics produce maximum displacement.

@HighlineGuitars

5 ай бұрын

Only if the frets are tall and the action is low.

@ralphclark

3 ай бұрын

@@HighlineGuitars everybody seems to want the action as low as they can get it so this is always going to be the limiting factor

I agree with what you have said in this video 100%...!

Thanks for sharing

Surely it's best to level the frets with the fingerboard level. Isn't the job of the truss rod to actually counteract the tension of the strings.

Hi Chris (as an enthusiastic ameteur) - I've found that giving a little neck relief can have an advantage with respect to the elcectronics especially of a neck pickup. If by means of the relief, the string height is a little higher, using neck relief, for example on a telecaster. The higher register notes on the neck can make proximity to the neck p/up (not so much bridge), significantly closer. The shorter arc of the string induces less output when the neck is straight, and notes are fretted in the upper register quieter. The trick is to have the neck p/up set high so it is very close to the strings on the top fret. In the lower positions this evens out volume also. I cut the nut slots very low, (this improves intonation in the first 4 positions), surprisingly, a little neck relief can raise the action around the open position without compromising the intonation. At least my tuner always seems to confirm this.

I like your detail explanation...my thought is level on flat neck the bow would not produce high frets.. biggest issue we have with buzz and such...and u can also adjust truss rod after strings if the bow is significant.. Thanks for giving me the value of your experience.

On the older style necks you can only tighten the truss rod. With it backed off all the way or loose ,you adjust the truss rod just till it feels like there is just a touch of engagement. Then you straighten the frets .When you restring the guitar there will be some relief caused by the string tension.

I found the same conclusion about the the neck jig! When I was fretting 4-5 a year I used one. When doing 4-5 a month?? NO WAY ITS WORTH IT!

Enjoyed that vid thanks. You probably already know this but Dan Erlewine also advocates for a flat neck with no relief. It makes a lot of sense to me personally so I appreciate you sharing your thoughts on the subject.

When he got the phone call about nothing needs doing and that is after posting the guitar where anything in Transit could go wrong and still nothing needs doing is a testimony to his True Craftmanship

Always good info , explained well. Fun fact, i smoked with Robert Plant on my porch in 2007 , in Nashville, because my next door neighbor was Roberts guitar tech/ personal assistant, house finder. Hung with him a few times

@HighlineGuitars

3 жыл бұрын

I've seen RP in concert 4 times since his Zeppelin days. Had a chance to see him once with Zeppelin, but a prior commitment nixed that. I still regret that decision.

Please make a video on how to straighten a scalloped neck and how to know if it's straight, including how to level frets on such a neck. Thank you!

Being a player as well as a builder, I prefer that a neck is as straight as possible during fret leveling, because that is also how I set up the guitars that I play. I have low, low action (1/16" under the high e at the nineteenth fret), super light strings (.008 to .038), do a lot of wide bending, and get no buzzing at all until the frets are quite worn down. My fret leveling tool is a 24" piece of hardrock maple with stick-it sandpaper, and after initial leveling along the length of the neck, all my sanding and polishing is done parallel to the frets. I feel that if I used this long tool to level frets on a bowed neck I would take more metal off the highest and lowest frets, leaving more metal on the frets in the middle. I can't see any advantage that would result from this. Thanks again for your well-considered, low key approach, the antithesis of some guys I will only refer to as "TTG."

Chris you are All ways very informative. Thank you for sharing your experience and knowledge.

Thanks man.

All you say seems very sensible. It seems logical to me to set the neck (well the fretboard surface) to be straight and then level the frets so they are as straight and level as the neck. In fact if the neck/fretboard on a newly built guitar is flat and the frets are properly installed it should hardly be necessary to level the frets at all. I think the argument about levelling under tension is that most necks don't simply curve under string tension but tend to form a S curve. They bow forward between the nut and around the twelfth fret and then rise in a small hump from the twelfth fret to the last fret. I think that, assuming that does happen, the idea is that levelling under tension, with the neck set as straight as possible, allows smoothing out some of that hump. However there are a number of demonstrations of the Plek machine on KZread that show the neck profile on-screen and I don't remember any of them showing a hump. In any case the hump is supposed to be the result of compressive force along the neck and I don't see how a neck jig, which only bends a neck forwards, is going to simulate that compression. I didn't think there was any mystery about relief - the idea is to approximate the vibrational path of the strings so a lower overall buzz free action can be achieved, than if the neck is dead straight.

@stephensaines7100

4 жыл бұрын

[They bow forward between the nut and around the twelfth fret and then rise in a small hump from the twelfth fret to the last fret. ] Yes! And this is what many refer to as the area needing "fall-away". It's a trade-off, and a whole separate topic really.

@ResoBridge

3 жыл бұрын

@@stephensaines7100 I've come back to this video after some time so excuse the delayed comment. I personally don't like the idea of a fall away on an electric guitar. In any case my point was that I have seen the - compression results in an S curve - theory propounded in a few places, and maybe it does happen in some guitars. BUT I have seen several KZread videos of the PLEK machine mapping the fret board and they NEVER show an S curve. All I have seen is a smooth and simple forward bow under string tension when the truss rod is set for a small amount of relief.

I agree 100 percent ur gonna tune,intonate&play it anyway. Each person can add there own Tweeks,bow,relief etc.

Great information, thank you! It is so helpful as someone who is just starting out learning basic luthier work to hear your experience and reasoning, not just instructions on how to perform a task. Every single one of your videos I have watched have been super helpful.

Goooood information...!!!!

I like to level with the neck set as straight as I can get it. Then control the geometry of the playing surface with the truss rod. I like around 8 thousandths of relief. I really enjoy digging in and snapping the strings in the lower area of the neck, and lighten up quite a bit as I move up. I tend to keep my action at around 2mm at the 14th on the sixth, graduating down to 1.5mm on the first.

This answers a question I have often wondered. If a neck jig produces bow forward or back can’t it be achieved by the truss rod? And if lower frets are desired in the higher notes or down at the cowboy chords, couldn’t it be achieved by applying slightly greater pressure to the beam in those areas? I’m just a hack but I’m here to get better. Thanks for the great info. Glad to find your channel.

A long time ago I was told that neck relief was required due to string vibration, and all this time I just assumed that was the optimal geometry. I've never actually questioned it until now.

Being a luthier myself and having tried the many approaches to this job. I have also found lvl neck equals a quality fret lvl and polish

@richardfinney8784

5 жыл бұрын

I totally agree with you on this great videos keep them coming.

Oh gosh! I love the way you explain things and the subjects you touch. One thing I've never done is fret leveled a scalloped fretboard. If you've done it, would you be so kind and share with us/me how you check the fretboard's flatness in this case? Thanks. 😊

@HighlineGuitars

9 ай бұрын

It's not possible to reliably test a scalloped fretboard for flatness that I am aware of. You can, however, use a precision straightedge to check how flat the frets are. Unfortunately, this approach has limited usefulness since the frets themselves probably aren't level yet. If the fretboard was glued to the neck, you can use a precision straightedge to check how flat the glue seam is. Again, this approach has limited usefulness since the scalloped surface may not be consistent from fret to fret.

That’s the best question, and I think yes totally flat when leveling. The truss rod can always be adjusted after stringing . Just my take! I’m a self taught Luthier that has apprenticed under a very strict builder that has forgotten more about stringed instruments than most ever know!

if you put some relief in you can be sure not to get a backbow in case the neck moves a little. i think it is a good safety measure to achieve a setup which will work without adjusting the truss rod very often. there are necks that move. unfortunately i have one in my favorite guitar.

I've tried dialing in a slight bow from the truss rod to try it and all I found was the higher frets 20 21 22 etc get taken down too much,,straight is the way for me !

The Plek story is a hardcore flex.

When I first started learning about guitar setups from books back in the late 80's/early 90's there was even a lot of differing opinions back then on the best setup techniques. Some even suggested having fretboards with built-in relief. I like to just set the neck flat and level that way. It also depends on what condition the fretboard is in too. Personally on relief, I think it depends on how the guitarist plays. If they're a light player, you can probably get away with a straight neck and no relief. If you're the type that likes to bash away (like many rhythm players), then a little relief to counter the string buzz is good. That's how I set all of mine up. But every guitarist is different.

Good info , I get it. Nice shirt!

My setup is frets level flat then pull a small amount of relief which allows my action to be just a little lower than normal. Here's how I think it works. If I play an open string the full 25.5" vibrates with the largest swing at the 12th fret. Okay say I play on the 5th or 7th fret now and with my relief it pulls further down than it normally would to fret. But it doesn't matter so much because the vibration swing isn't going to be near as much as an open due to the shorter length. There's that sweet spot that makes the strings fret so good and the action is low.

I always level after a refret with the board completely flat. My mate brought round a guitar for me to check out. Due to it being a freebie I didn’t want to do the whole half a day levelling crowning, going through all the grits. So I actually spot levelled it under tension. I ran a rocker over the whole guitar with it tuned to concert, marked the rocking frets, the took the strings off, spot levelled the 7 frets, re crowned polished then re checked with the rocker and it was spot on. I thought as I was checking 3 frets at a time so the 10’000 of a relief wasn’t an issue. The guitar played great.Didn’t choke and when it’s ready for a refret I’ll do it the traditional way. But for doing a mate a free favour the time I spent was so significantly less. Plus he keeps more fret material which is a bonus. I’m sure Chris only spot levels I saw in one of his videos to save time and fret material. I think actually if you spend the time on getting the board level and you have done your fall off. The spot level is a great time saver if it’s circa 7 frets or less.

@HighlineGuitars

Жыл бұрын

These days, I do a full leveling during the initial assembly stage. Later on, when I get to the final setup of the guitar, I'll do just a spot leveling.

@MrSongwriter2

Жыл бұрын

@@HighlineGuitars ah I’m going by one of your old videos then. I still completely agree the more time you spend on getting the fingerboard perfect the less metal you loose on the frets. Plus it does speed up the levelling process as you’re hopefully skimming the tops “in theory” a old neck is different to a guitar you’ve built for sure though.

I'm having a guitar leveled now on a simulated tension jig. I thought about it and don't like that idea. If you level the frets on a straight plane, the frets will be on a straight plane whether there is neck bow or not. So a neck slightly bowed in a jig will still have a flat fret plane. So if you want relief you have to bow the neck even more. The only advantage to simulated tension while leveling is if you can't get the neck 100 percent straight. This is all assuming your using a long fret level like 18" or so. It's better to be able to set the neck straight and level, and keep it level after strung up. If more bow is necessary give more bow. The fret plane is something nobody ever thinks about, level is level, regardless of what the neck is doing. And you'll wear down the first and last frets unnecessarily by simulating tension.

Lots of people are saying that a neck jig is pointless, but my understanding is the main reason they exist is because some necks will twist / warp slightly under string tension, so using the neck jig means the tops of the frets will be level when the guitar is strung up and under tension (i.e. when it really matters) as opposed to when it's not under tension. As far as I know (I don't own one), you would typically still adjust the truss rod to get the neck as straight as possible before levelling; the only difference would be any small variations in the contour of the fingerboard between "flat and no tension" vs. "flat and tension". In cases where there's a difference between the two, you want to level for the latter as that's how the guitar will be played. Of course, as Chris said, he builds guitars and so knows the necks he is working on are consistent. If you run a repair shop though, that's not always going to be the case.

ive torchered my share of bent necked cheapies from used stores. mostly cure intonation first by redoing the bridge. that may only mean easy or worse, but also set basic string height. to really have it easy, and moveable tail pieces make it so. best to get all that cured first, then string 'er up and play some. best i read was that when a string vibrates, a very stretched pointy ended cone forms that measures fattest at the 1/2 span. so clearance beyond the 12th fret adds dissonance, but a bit of bow to there gives air. so i often prefer to work a partially finished inst. strung and tuned; then detune/prop strings away and finish the buzzy frets and stuff. l guess its really about paralleling an ellipse but heavier strings take more room too. closest reasonable action basis starts here.

to receive a phone call from a pleckin tech and get asked "what should i do with this ?" is a heck of a compliment.

Solid! 👍🏻

Kind of like when tuners became widely available. Suddenly, intonation was measurable and of primary importance. Even though people had played, recorded, and made hits with out of tune guitars. I like my neck with no relief. Here's why. If I set the relief about .010 +- before it plays well I will also have to induce fall away beyond the 12th fret. This,I believe, is because at mid neck the guitar is fingering in a trough, which rattles up the neck. Chet fans know he liked .008 relief, but what is less known is he preferred a high action. If that's his recipe, so be it. For me, my recipe is no relief, low action, no fall away. Since I haven't made 60 years worth of wonderful recordings, I doubt anyone would ask for my preferences. The point is, players should find their preference rather than copy something they heard or read about without getting the whole story. Great video.

I like your straightforward approach to this problem. Sometimes YAGNI is the best approach (as in software development), "You Aren't Going to Need It".

Re: general relief preference (as a player) I find I need some relief rather than a flat fretboard with a 9.5” or especially a 7.25” radius so that I can set the action medium-low and have whole step bends that don’t choke out. Could just be that my frets aren’t completely level though!

I agree 100%. Flat necks generally produce very good fret work. A lot of techs only support the headstock end, then they reef on their sanding beam... That grinds a big hump in the frets and can actually make the guitar play worse... A well supported neck is all you need (sand bags, cork, adjustable pins like you have, etc.)

@sleepyhorndog6004

5 жыл бұрын

SkyScraper Guitars Yeah, the weight of a leveling beam alone is enough to hog off a lot of fret height fast. Even with 600 grit. No need for elbow grease.

@SkyscraperGuitars

5 жыл бұрын

@@sleepyhorndog6004 Truth!

I think leveling frets with some relief on the neck would only be right if you could simulate the exact relief the neck has with strings on. And even in this case I admit I'm not sure if it would the best option... Mmmm, it makes me think... 🤔

Relief, to me, seems to be extra space between the string and the fretboard that is unnecessary. This wouldn’t be an issue if it were not for the fact that that means the strings intonation will change more dramatically by having to push it farther through the relief. I’ve always wanted my necks as straight as possible.

Great video! When levelling a fretboard which isn't new, how do you account for the fact that frets 1-11 will likely be more worn than 12-22+ (at least mine are) Even though the fretboard will be flat, the levelling beam wont sit exactly parallel to the board because of the uneven wear, and will take off fret material at that slight angle. This will still give the impression that the frets have been "levelled". Does the fall-away levelling solve this issue? Thanks

@HighlineGuitars

4 жыл бұрын

That's not an issue I have to worry about since my videos are geared more toward making new guitars.

At 10:20 I’ve learned from working on the gulf coast for 10yrs that players who frequently play both indoor and outdoor gigs goin from no relative humidity to 100% humidity that relief allows for acclimation between the 2. I learned real quick on some of the first set ups I did, I quickly learned that I had to adapt my understanding of what is correct vs what is best depending on circumstance.. Just the low pressure storm fronts that move through will quickly change every guitar on my wall... I assume manufacturers know this well and is the reason “factory specs” (I hate that damn phrase when talking about guitars) calls for relief

@rb032682

5 жыл бұрын

I played the Eastern half of the USA in the 70s. Every time we played in Ocean City MD, I had to adjust the necks on my wooden guitars and also had to adjust the relief on the bass player's 4-str. Precision. When we went back inland, we had to re-adjust the necks to the lower humidity. We played other gigs near the Atlantic ocean and the Gulf of Mexico, never really had to make relief adjustments like we did in Ocean City.

@rb032682

5 жыл бұрын

@We all - That's why I changed my neck preference to aluminum or graphite composite. No truss rod necessary.

@thespiritof76..

5 жыл бұрын

RB I’ve worked on tours all over the US but never have I seen anything like lI do working on the golf coast on the gulf coast... Ocean Springs for crying out loud!

@rb032682

5 жыл бұрын

@@thespiritof76.. - "The Golf Coast." I like that. 👍😎

Don't ever level frets with a forward neck bow (simulating the string tension) or you will create the hip in the middle of the neck by shaving the neck ends more. The dead straight neck or with a tiny back bow, if you can't make it straight all across the board, is the right way to do it.

Love your videos, Thanks for sharing your hard earned knowledge. In the case of non professionals like myself, might a neck that’s not completely supported deflect slightly during leveling throwing the level job off slightly? Where a neck jig would hold it straight during leveling even if a but too much downward force we’re applied with the beam or file, resulting in a better job?

I agree totally... only makes sense.... If you have a perfectly straight and level fret board ... everything "should " work ok ..... if not tighten the trust rod ... sometimes things are made more difficult than need be

In my experience with repairs, yo DO NEED to have the neck under simulated tension, mostly because of popping frets. I've done it straight and then when tension is applied some frets pop out, Now remember I said my experience with repairs, when wood is old fret slots are wide, or new; but with a deficient factory fret job. Gluing the frets is a must in extreme heat cities like mine, wood just moves. And the other point is relief on a guitar: my theory is that a string vibrates in a circular manner, relief facilitates that, avoiding buzzing. Anyway this is my experience and my two cents, again a spectacular video from Highline Guitars.

I guess my own reasoning for a bit of forebow / relief "in theory anyway" is the fact that the open string travels more in the middle or arcs, and that forebow follows this same shape as you know. Mind you, sometimes it doesn't seem to work at all and it's something I could never get down consistently. I've aways used the test of a finger on around the14th fret and first while plucking it allowing the string to vibrate freely. Wood is very inconsistent and reacts differently under stress as you also mentioned too, It may arc more towards the headstock or closer to the body. I agree about fret work on a level board first.

@armandosinger

8 ай бұрын

It’s true that the open string tables more in the middle. But optimizing for the open string vibrating can cause problems when you fret that string. Open, the greatest travel is over the 12th fret. Fret the 12th fret, and the greatest travel is now over the up bowed high frets, if you have relief.

Only reason I’ve found that you need neck relief IMO is uneven frets or it’s set up for slide! Keep in mind neck relief throws the intonation out... Any change in the truss changes the scale of guitar. On some vintage guitars this is necessary for easy intonation

@michaelhamerin3814

5 жыл бұрын

That's why u intonate as a last step to a setup.

@thespiritof76..

5 жыл бұрын

Michael Hamerin absolutely.. Your average player that does their own string change and truss adj don’t have a clue as to why.. that your actually shortening and Lengthening the scale

Oh man, if I ever got a call from a PLEK company saying "your guitar is perfect", I'd feel pretty badass.

@HighlineGuitars

2 жыл бұрын

Just keep in mind it all depends on the skill of the PLEK operator.

@chrissturley823

2 ай бұрын

Nah. This dude was flexing when he told that story. But I don’t blame him. If I got that phone call, I’d be telling that story too. “I’m as accurate at a f’ing computer”

After watching several videos, I see that some people level the fretboard (not the frets) with strings and some without. It seems to me that it would be better without strings because if the fretboard is level without strings, when you string the guitar, the tension should produce a natural relief. Is this correct?

I know for myself I like a little bit high action because it makes bending strings way easier, especially the high e string. I bet that's why players like the bow. I've straightened out a neck and hated it, because it made bends feel super stiff. So I used to play with a big bow, then I realized that I could just raise the action at the saddles, lol. But I still like about .010 gap of relief in the middle of the neck, because I'm a dynamic player and I play really clean a lot and I "Hate" fret buzz.

@robertlevasseur8896

6 ай бұрын

He’s not talking about action he’s talking about relief.

I've done it once. I saw no reason to simulate the bow. Just do straight totally. Here is another question that is a big debate that I cannot get a straight answer....do you use a flat beam to level or one with a radius to match the fretboard?

I agree that the slight bow some players like is indeed because they simply have gotten used to that geometry of the neck and then they deem that as the correct feel of the neck. It always amased me that the smallest turn of the truss rod nut can change the stiffness of the strings and they feel on certain guitars. I dislike necks that have a higher action in the middle going up to the 12-15 frets and then too low going up to the 22nd frets ect. I like a low action and smooth transition getting ever so slightly higher at the heel of the neck but too low makes them feel harder to play and too high is also not ideal. My friend had an Ibanez floral Jem that was PLEKED and the action was utterly perfect. I now own that 1990 floral Jem in pristine condition and I am seeking a guitar tech guy who can do this guitar again as it was when my friend owned it. No buzzes but low for slick fast playing but not too low that I can't dig in and get some finger flesh under the strings. I also love tall frets but haven't really tried SS frets yet. I have played an ESP with SS frets and the bends were effortless and I loved the high end twang that SS frets have slightly more than N/S fret wire. I wish SS frets have the same choice as Dunlop wires do like the 6505 and the tall but slightly narrow wires. I wish their was also a system that reduced the sharpness that guitars suffer from as they can't intonate correctly. The sharpness is always from the nut to around the 7th fret area. Maybe fret wave tech is the answer.. as if I tune my guitar to a perfect Dmaj chord then Amaj is always out by quite a lot and this really hurts my ears as the maj 3rds sound sour to me. I think an overhang of those frets could help this problem but nobody has made special frets like this with a normal tang but a wider fret that flattens or sharpens specific frets would be awesome.

I made my own neck jig years ago and used it with great sucess. But I also found out years ago that it was a lot of unnecessary work. So I no longer use as a regular thing. However when using a jig the neck still needs to be flat/straight. You would not want to simulate relief in the neck and then sand it with a flat beam that would create a back bow once out of the jig. Also I started out using a dead flat neck on my first guitars but it's impossible to get a low, 4/64, string height without buzz without some relief in the neck. I don't use neck relief as a cop out for a bad set up. .080 as a rule. I do use the fret jig when doing compression fretting on old Martins that don't have adjustable truss rods. I agree a good fret job is miles ahead of the plek, not a fan.

@dannyjonze

5 жыл бұрын

and once in the jig. how is it flat/straight? as it is simulating string tension... is not the point of the jig to level th frets with simulated tension, therefor with a beam ,no matter what would happen if it was relased

@jonahguitarguy

5 жыл бұрын

@@dannyjonze, Hi Danny, the point is to flatten the neck out under string tension and then take the strings off and re-establish the flat neck with the head jack and the nut strap. Without changing the truss rod so when set the neck is still exerting the same stresses. Watch the Dan Erlewine video he explains it very well. Heck somewhere in my videos there's one showing how to use the jig.

Is it easier to have frets too flat or too radiused? I ask because for example an owner buys 12" radius for a 14" radius guitar versus owner buys 16" radius frets for a 14" radius guitar. It has me wondering 🤔 I guess the question should be, is it easier to flatten or bend frets to the correct radius.

As to "neck relief". I've mostly seen that preference on acoustic guitars. I'm not keen on it at all. I like a flat board for a more buzzless finger licks up the board.

Music man are leveling the fretboard (not the frets) with some back bow tension on the trussrod. That give a bit of adjustability to get a correct relief when you are using slinky strings. Otherwize the neck is to rigid to bend even if you loosen the trussrod all the way.

If you want to level with string tension, you could try the Katana levelling system, it has the strings still attached on the guitar while levelling.

@HighlineGuitars

5 жыл бұрын

The Katana leveling system has been around for a while, but it doesn't seem to have caught on the way I would have thought. I was going to try it myself, but other guys I know who have used it advised me not to waste my money.

@jsd5150

5 жыл бұрын

The Katana works extremely well.

@crisbochguitar

5 жыл бұрын

@@HighlineGuitars The Katana leveling system is a genius invention. It needs to be used properly, but it works great. I started with the flat fretboard and straight bar system and I was satisfied. I also self-built a neck jig, similar to the Stewmac's one (the concept is very simple). But when I discovered and got the Katana, I would never get back to other systems. Give it a try. It's worth the money

@migranjitaeducativa

5 жыл бұрын

@@HighlineGuitars Hi, You can ask Davide Bissoli ( The Mad Genius behind the Katana and other designs ) to lend You a Katana for testing, if You like it You can buy it, if not just return it, He has also a nut file called littlebone has the shape of a bone that crowns the frets perfect without worry of modifying the fret height, I own 29 guitars and after having done two of My guitars boutique setups that included fret leveling on the best Guitar Repair Shop in town I figured that I had to do it myself because of costs related, I know how to setup and repair the electronics, but I did not have the tools for fret leveling and crowning tools etc.... So I started looking around and found Rectify Master Videos and website ( name of the company ), saw some videos from Davide and from others who dare testing it and gave it a try, long story short, the Guitar Repair Shop with all the tools including Stewmac Neck Jig and traditional tools take about 4 and a half hours to level and crown a 22 fret guitar, I ordered the Katana and littlebone to crown frets and did My first leveling and crowning in 1 hour and a half, the guitar is a cheap Cort guitar and ended with lower playing action without buzzing than my Gibson Les Paul Custom without experience I did a similar work than the Guitar Repair Shop and in less time If You give Yourself a chance You can find a very useful tool, from the other guys that have tried out the Katana it looks tht they have achieved similar or better results using the Katana, just my two cents, great channel, I have learned a lot with Your insightful videos, thanks.

One of the prime purposes of an adjustable truss is to provide relief or the correct balance of forces with a given set of strings to render that. For those believing the relief should be hard set into the frets (a bit of a contradiction for fret height itself, an important factor of playability) then just use a massive steel truss in lieu of an adjustable truss from the get-go. Are highways skimmed on their asphalt thickness to make up for dips and bumps? Hardly, it's the base where that's done. Frets are not the devices intended to correct for what a truss should correct for. If the neck doesn't adjust properly, then the *fallback* option is to try and do at least some of it in the frets, but that's a last option, not a first one.