Shop Dust Collection Update Oneida Supercell
Тәжірибелік нұсқаулар және стиль
Subscribe: / @maverickmakersusa
Instructables Page: www.instructables.com/member/...
Disclaimer: This description contains affiliate links.
4 Inch Flex Duct
amzn.to/3ItBRNc
Hose Reel
amzn.to/3NR10Cw
Blast Gate
amzn.to/3O0oPrw
4 Inch to 2.5 Inch Reducer
amzn.to/3OZC2SK
4 Inch Cuff
amzn.to/3yxZVd8
Please like and subscribe if you find it useful and check out other projects on my KZread and Instructables pages.
Пікірлер: 19
Thanks for the review. I've been looking at the rather large Laguna collectors as well as the Harvey dust processor. The Supercell is on my list too and I really like that it can be mounted on the wall. My collector will go in a corner of my shop and I plan to build a closet for it. The Harvey saves space by being relatively low, giving you the ability to have a work surface above it. But, I think the wall-mount for the Oneida and its approx. 2 s.f. foot print is a good option.
It’ll be quite a while before I can get a supercell but I do have the Camvac 90L from Record Power. It’s some of the best money I’ve ever spent. Including the 220v installation. The only thing I wish was different is that it had the ability to be turned on wit a remote. It’s not that big of a deal anyway really but it would be nice. I’ll never go with a low pressure system again
Great video, I'm looking at the one you have and looking at the Harvey G700 Gyro dust processor.
jealous,. My supercvell is right next to me and I can hear that thing through my ear protection which is the biggest ones 3m makes.
Thanks for sharing your setup. The noise reduction from your closet is impressive! Does the temperature get pretty high in the closet?
@MaverickMakersUSA
Жыл бұрын
I was a bit concerned about that at first, but have only noticed slight increases in temperature. When I work on projects it isnt running constantly and I usually have periods where I'm assembling and planning when it is off. The return air duct may also be mitigating heat build up.
Ever thought of an overhead trolley or crane system for holding hose for hand tool dust collection? Nice setup so far. You're already in the top 1% of woodworkers now lol.
@MaverickMakersUSA
Жыл бұрын
I'm still slowly working on my new shop, but would eventually like to have an overhead system. I'll be sure to post if I design something.
@MustPassTruck
Жыл бұрын
@@MaverickMakersUSA Will be looking forward to it.
Brilliant putting your excess noise producers behind the wall. Do you get any sawdust from the top of the blade? I’m trying to reduce that without putting an attachment above the tablesaw. Wondering if this take care of that.
@MaverickMakersUSA
Жыл бұрын
It really depends on the cut I am making. If I'm trimming up the side of a piece of wood I get a lot more dust than if the blade is mostly covered by the wood through the cut. I don't have any issues with the finer dust, but there are definitely some larger chips that end up on the table when there is no attachment over the blade.
How are you venting the closet? Does it go back into the shop / contribute to the noise?
@MaverickMakersUSA
Жыл бұрын
I have another video on that, but yes it vents back into the shop with very little noise.
I noticed in the manual it calls for 24" of additional clearance above the unit so you can access the filter. It doesn't look like you have 24" of clearance, so is that a problem when you access the filter?
@MaverickMakersUSA
5 ай бұрын
I have about 13" clearance and have no issue getting the motor housing off to access the filter. You could probably get the housing off with as little as 8-10" of overhead clearance.
What brand of Y-Connectors and Blast Gates are you using?
@MaverickMakersUSA
8 ай бұрын
Powertec. I left a few links in the video description.
How many blast gates can you have open at a given time?
@MaverickMakersUSA
Жыл бұрын
As you can see in the video, when I had 2 gates open the flex hose was not collapsing versus when one was open. The system is designed and really works optimally with only one blast gate open at a time. I'm a one man shop so I don't have any issue running off one blast gate.