Appreciate you passing down your knowledge to us who like to maintenance our own reels

@2ndChanceTackle

11 ай бұрын

Thanks for the kind words and for watching - Dennis

A friend showed up with one of these that was inoperable. As usual, after viewing this I knew exactly what to expect. The owner is now a happier camper. Thanks!

@2ndChanceTackle

Жыл бұрын

YW - Thanks for the note and for giving your friends reel a 2nd Chance - Dennis

Thank you!

Thanks Dennis. I have 2 of these exact trolling reels. Very helpful!

@2ndChanceTackle

6 ай бұрын

Glad to help - Thanks for the note and for watching - Dennis

Hello Dennis . . . Nice fishing reel - adjusting the free spool is some what tricky but to the person who will be using it they should get use to it - good video .

@2ndChanceTackle

Жыл бұрын

This is a warrior and one of the best - Thanks

Always wanted to try a Shimano Triton but fell in love with the Daiwa Sealine series and never looked back

@richardsurber7928

Жыл бұрын

The Sealine, Slosh and Seagate are awesome reels.

@2ndChanceTackle

Жыл бұрын

These are two good companies that make very nice and competitive reels. Competition always helps. The mega conglomerates seem to lack that initiative and produce me too reels - Thanks

Good evening Dennis. At one time replacing line was inexpensive, not anymore, at least for large reels. Smaller reels that can be filled with a 1/4 pound spool are inexpensive to re-line. A large reel which requires 600-800 yards of line or more can cost you over $200. When you get into the 130 class reels, (150 - 250 lb test) figure $700 for a mix of mono and braid. Ultra violet light is the culprit with damaging monofilament fishing line. Keep the reels covered and you can extend the life of the line. Braid is more effected by abrasion, so inspect your line at every use. Keep up the good work.

@2ndChanceTackle

Жыл бұрын

Thank you well said and good tips - Dennis

Great Content! I have a question on a tld50. Actually 2 of them since purchased new. Drag is set to desired setting, however almost fully engages as soon as the lever is advanced out of freespool. Any idea what this could be?

@2ndChanceTackle

Жыл бұрын

It sounds like the pre-set adjuster has been tightened. Do you lose max drag if you back off the pre-set? The other cause could be dirt and debris clogging the drag washer. It may need to be cleaned - Those would be my first guesses

Hello, I have a 300 Mitchell myself. I took it apart to clean and fresh grease. I put it back together correctly but noticed when turning the reel handle the spool should so up and down constantly? Mine goes up and stays up for about 20 turns then goes down and stuck down for another 5 to 50 turns. The teeth on the gears look fine. The gear with the 3 nubs on the back that goes in the plate might be worn slightly. What could cause this?

@WolvCustoms

Жыл бұрын

I apologize words are hard not a good explainer

@2ndChanceTackle

Жыл бұрын

It would be the gear with the 3 nubs. remove the gear side plate and isolate the slide mechanism and gear. Turn the gear by hand. If it does not go up and down easily, your gear is mismatched to the slide bar. Raise the gear up and rotate it one step at a time until you can move the slide bar through the up and down range. If that doesn't do it, then one of your gears, probably the one with the nubs on it probably has missing or damaged teeth.

@WolvCustoms

Жыл бұрын

@@2ndChanceTackle THANK YOU so much for your reply and time doing all these videos. I appreciate you sir

Hi what is the preset nob spring do

@2ndChanceTackle

8 ай бұрын

It sets the strength of the first strike and full drag on the lever. If you want less drag on first strike, you back off the preset and more drag - tighten - Thanks for asking - Dennis

@user-qi2eu4ei2i

8 ай бұрын

@@2ndChanceTackle if I use my lever drag reel with out the spring will the reel get damaged

looks borderline over filled with line

@richardsurber7928

Жыл бұрын

Definitely

@2ndChanceTackle

Жыл бұрын

More than borderline!