Sharpen Your Drill Bit Like a Factory with This Tool!
You can sharpen drill bits at factory settings with a simple tool you can make in your workshop. Simple drill bit sharpening. How to sharpen a drill bit the fastest?
You can sharpen drill bits at factory settings with a simple tool you can make in your workshop. Simple drill bit sharpening. How to sharpen a drill bit the fastest?
Пікірлер: 41
The drill has its angles... The drill is sharpened with a rotating movement and by tilting it down so that the cutting surface is lower than the cutting edge... This is knowledge, art and skill, and you won't achieve it with this device, you'll only mislead people. The chips must be identical on both sides of the drill - this is the symmetry of sharpening
@ypaulbrown
21 күн бұрын
the drill sharpening does not need a rotating movement to make a relieved curved surface, the way he is sharpening the bit is fine, with two facets, one lower than the other, the reason a factory bit is curved, is it is easier for them as they have a cam that will move the bit, instead of grinding in two positions... there is relief on his way of sharpening ...... are you familiar with the proper back relief of a drill bit and how the size of the bit will change the relief angle ? please let the other viewers and commenters know ..... I personally own a Black Diamond Drill Bit Sharpening Machine, so I know a little about the sharpening of a drill bit....
I can do this by hand. I don't see 1-2 mm sharpening anywhere.
Very good video. Thanks
great idea, but the long spiral chip is not good, too much feed pressure...the rigatoni chip is good
J'aurais aimé voir vos angles de coupe en plus du 120° de base ...
интересно что скажет гуру, мне надо заточить сверло 0,8 миллиметра...
@user-jq9wm7me4d
18 күн бұрын
Проще новое купить
Didn’t see you checking the angle length from center. Kinda important for drilling accurate holes of any depth.
@robertwoodroffe123
7 күн бұрын
I used to do from 1.5 mm to about 55 mm by hand and eye ! Sometimes used a square to check Chisel point in dead centre and angle on cut edges same on larger sizes
во первых для правки камней существуют алмазные карандаши! во вторых, на заводе заточка осуществляется станком при изготовлении, а не рабочим (заточником) и в третьих - угол заточки между двумя сторонами сверла должен быть 120 градусов или по внешней стороне относительно оси - 60 градусов с обеих сторон, еще в четвертых и в пятых : режущие кромки должны быть одинокавой длины и абсолютно не иметь "пятки" - она должна быть ниже режущей кромки ну и конечно не допускать цвета "побежалости" - металл горит или отпускается...
Why not use a grindstone dresser
@ypaulbrown
21 күн бұрын
he does not have one
@geoffankrett7012
20 күн бұрын
@@ypaulbrown obviously 😂
Правильно, ребята,! Ты че носом в сверло таких знатоков
- interessant 👍👍
кулибины так сверло на заводах никто не затачивает.
es gibt do extra für schleifsteine einen abrichter
@ypaulbrown
21 күн бұрын
there are many types of dressers, diamond, steel wheels, CBN.... why beat the man up for the way he dressed the wheel?
Проще болгаркой заточить сверло.
Точно так же можно болгаркой наточить, безо всей этой х..еты . При наличии прямых рук, а дуракам и эта "приспособа" не поможет.
Une technique reprise et reprise qui ne montre pas grand chose sauf à ne pas faire. Je perce tout les jours, donc j'affûte mes forets régulièrement et je peux vous affirmer que des méthodes nous en avons essayé et rien ne vaut la bonne vieille méthode d'affûtage. Il est aussi important d'avoir de bons forets.
@philipperouveyrol8606
23 күн бұрын
absolument d'accord
Не! Пойду лучше наковальни в ртути топить! Или положу в холодильник ТЭН и включу оба, чтобы посмотреть кто кого победит! 🙂
Mauvaise méthode
@RovinjJoe
27 күн бұрын
Why?
@ypaulbrown
21 күн бұрын
and why is this.....give the reason why...
Нужно направляющую перевернуть иначе весь абразив попадает на шарики направляшки
ich schleife meine bohrer mit der hand , ist schneller und besser
@foxwhiskey
27 күн бұрын
Sicher. Wenn man's kann !👍👍👍
@ziegenwilly
27 күн бұрын
@@foxwhiskey hallo , das kann man ganz schnell lernen , ist doch sehr einfach
@user-fd6ul2ol7t
25 күн бұрын
😂Вася не смеши,затачивает он вручную😂если ты сточил с одной стороны 0.1мм то как ты с другой сточишь 0.1мм?
@ziegenwilly
23 күн бұрын
@@bernhardschwarz4302 so , ein unsin , was sie da schreiben , das war mit das erste was ich als schmied und landmaschinenschlosser gelernt habe , wer hätte sonst die stumpfen , oder auch abgebrochenen bohrer schleifen sollen
@bernhardschwarz4302
23 күн бұрын
@@ziegenwilly die Antwort war nicht für dich gemeint, sorry
More garbage that you don’t need.
@ypaulbrown
21 күн бұрын
why all the hate
@ronaldpatton5668
21 күн бұрын
@@ypaulbrown because it’s not the proper way to sharpen a drill. I spent 40 years as a toolmaker so I know what I’m talking about.
👎🤡
Никогда не буду портить свой инструмент!Жирный Минус!!!