Shargeek Storm 2 100W Teardown and Repair

Ғылым және технология

One of our riders dropped this rather expensive power bank while riding and broke off one of the input/output barrel jacks. This video covers the tear down, surgery and reassembly.
Products used:
Soldering Iron: TS100 with a Knife Edge tip
MG Chemical 60/40 Solder
NC559 No Clean Paste Flux
Chipquik SMD 1 solder
Engineer SS-02 Solder Sucker
Digikey part # P-051AH-ND (Conn pwr jack 2x5.5mm Solder)

Пікірлер: 22

  • @stevenlondon7210
    @stevenlondon7210 Жыл бұрын

    Excellent Video! I actually have this Storm2. Got it with a discount and a gift card.

  • @sewiim3612
    @sewiim36127 ай бұрын

    I lost the mini screws that hold the metal plates u have any idea what types those are?

  • @BobGarrett66
    @BobGarrett668 ай бұрын

    Is it possible to replace the batteries in this power bank. They appear to be 18650s. If it is possible, is there less tear down involved than what you had to go through to work on the board? Thanks for the video!

  • @MochaboyRC

    @MochaboyRC

    3 ай бұрын

    Absolutely - whether or not it's worth your time is a different story though

  • @kamilk6807
    @kamilk68079 ай бұрын

    I need to replace USBA on this powerbank. Any tips how to locate the part number?

  • @MochaboyRC

    @MochaboyRC

    9 ай бұрын

    You need to grab a set of digital calipers and measure the distance between the through hole posts on the usb-a header. After that - it's just a matter of going over to digikey and comparing the photos of the different headers with the one you want to replace. When you find a likely candidate - you need to download the data sheet and go to the technical drawings towards the end of the datasheet and compare your measured dimensions with theirs. That's just the task of finding and matching the part. You also need a way to remove the broken header which is a whole other skill set and set of tools. You will need a soldering and something called "desoldering compound" - best product on the market to use is Chipquick SMD-1. It's a special type of solder that stays molten for anywhere from 3-5 seconds which gives you a chance to use it to simultaneously melt the solder around the 4 or 5 installation posts allowing you pull the part off the PCB.

  • @Oscar-eg8ov
    @Oscar-eg8ov9 ай бұрын

    Hi, when taking this apart I managed to break the display, do you know where I might find a replacement part?

  • @MochaboyRC

    @MochaboyRC

    9 ай бұрын

    Oscar - unfortunately no - from the brief time I had it it appeared to be a proprietary oled display. Sorry for your trouble there - it's a nice power bank.

  • @Oscar-eg8ov

    @Oscar-eg8ov

    9 ай бұрын

    @@MochaboyRC Ah i see the ribbon has 18 pins and it's a 1.14inch display, if I were to order a generic part is there any reason it wouldn't work? I.e. What's proprietary about it?

  • @homz83

    @homz83

    9 ай бұрын

    ​@@Oscar-eg8ovI had the company send me one

  • @MochaboyRC

    @MochaboyRC

    3 ай бұрын

    www.alibaba.com/product-detail/Topwin-1-14-1-14inch-1_1600650299153.html?spm=a2756.order-detail-ta-ta-b.0.0.50da2fc2dtaH9W

  • @EpicallyJess
    @EpicallyJess3 ай бұрын

    Do you know where I could source a replacement screen for this model?

  • @MochaboyRC

    @MochaboyRC

    3 ай бұрын

    Unfortunately no - I would imagine digikey, but failing that - I'd have to research the size and number of conductors on the ribbon cable, size of the screen and see if a suitable replacement can be found on some of the chinese electronics sites. The issue is the oled driver and whether or not it's compatible with the board so might take some trial and error. What exactly happened to yours?

  • @MochaboyRC

    @MochaboyRC

    3 ай бұрын

    Never mind - seems like someone figured it out. www.alibaba.com/product-detail/Topwin-1-14-1-14inch-1_1600650299153.html?spm=a2756.order-detail-ta-ta-b.0.0.50da2fc2dtaH9W Let me know if you need help with the repair - we can do another repair video :D

  • @EpicallyJess

    @EpicallyJess

    3 ай бұрын

    @@MochaboyRC So SHARGE was kind and is sending me a replacement, AND I ordered the screen from TopWin. I would be happy to send you both screens for a comparison to go along with a repair, but the shipping cost may prove prohibitive. I'm in Southern Ontario, Canada. I'd be happy to contribute hardware for the purposes of helping the community that uses these devices (as long as I get it back). Let me know if you'd be up for it. - Jess

  • @MochaboyRC

    @MochaboyRC

    3 ай бұрын

    @@EpicallyJess Yeah I think that could work - why don't we take this to email and work out the details...my email should be in the "About" card in the channel/video details (just turned it on - never realized I didn't have that published).

  • @Light-DelaBlue
    @Light-DelaBlue5 ай бұрын

    did you know the reference for the screen? mine got dead lines....

  • @MochaboyRC

    @MochaboyRC

    5 ай бұрын

    Unfortunately I don't. You might want to grab the dimensions with a set of digital calipers and see if anything in the digikey catalog fits those parameters. www.digikey.com/en/products/filter/lcd-oled-graphic/107

  • @Light-DelaBlue

    @Light-DelaBlue

    5 ай бұрын

    thanks i hope i can find it its not normal taht screen is so delicate i never droped it never put it hard on the desk.@@MochaboyRC

  • @MochaboyRC

    @MochaboyRC

    3 ай бұрын

    Someone on Reddit posted this: www.alibaba.com/product-detail/Topwin-1-14-1-14inch-1_1600650299153.html?spm=a2756.order-detail-ta-ta-b.0.0.50da2fc2dtaH9W

  • @VermontLife802
    @VermontLife8022 ай бұрын

    Junk!! Buyer beware!! Barely used mine and it’s not working. Complete garbage!

  • @toetie2019

    @toetie2019

    Ай бұрын

    Did you contant support?

Келесі