Thank you very much! This is extremely helpful!

@MovieUniversity

2 жыл бұрын

Glad it was helpful!

Here’s my easy set up. Set the speaker configuration to small. Set the crossover on the front two mains at 80HZ. Set the center channel crossover at 10-20 HZ above the speaker rated level. Set the surrounds the same way snd any atmos speakers at 110 to 120HZ. Set the subs to 60HZ on the speaker. This will get a smooth roll off from the fronts set at 80. In the AVR set the bass level to LFE and the crossover to 120. This works very good for low power receivers. I have the marantz NR 1711 at only 50 watts per channel but it works extremely well when not using crossovers at lower HZ. I have the Klipsch Rf26fa towers with Dolby atmos upfiring speaker’s integrated. Running a 5.1.2 setup with two Subs.

Thanks 🙏

@MovieUniversity

2 жыл бұрын

You’re welcome 😊

I usually set 20-30 Hz above the +/-3dB measurement in the specs. My current bookshelves are rated down to only 100hz, so I set it to 120-150hz depending on placement (boundary reinforcement)

Speaker placement is just as important as crossover. Get your centre channel to the outside edge of the cabinet!

@davidjudd951

Жыл бұрын

I'm new at this stuff. I recently moved the center speaker to the edge of the cabinet only because I was trying to fit the turntable without pulling the wires. So there it is on the edge until I figure out the final spot for the turntable, I go to watch the movie "Beast", with Idris Elba, and I was surprised at the improvement in sound. The roar of the lions really came to life. Thanks for the tip.

@theradiantchild

5 ай бұрын

Forward or back of cabinet towards the wall?

I did an auto calibration my fronts audio pro avantek six when down too 40HZ. My center too 100HZ. My surround 120hz. LFE 120hz . Is this a good setup ? or should i bump up my mains too 80 hz ?

I’m using a pair of Wharfedale speakers 9.1 only… for front speakers; along with my pioneer VSX 933; to play CD music and also from KZread. i have a choice of cross over settings. Either, 50, 80, 150 or 200. But not really sure which setting, to use. Sunday 12th March 2023. U.K. 🇬🇧 Southampton

Great video!! I have a couple of questions. Here is my setup: Denon 4700 Klipsch R-625FA Dolby Atmos Floor stand speakers Klipsch RP- 504C II center channel Klipsch R-41M Bookshelf speakers Klipsch R-12SW subwoofer 1-What are your suggestions for the crossover settings? 2- What are your suggestions for the db level for all the speakers? This is where I am confused.

@MovieUniversity

Жыл бұрын

I hate to use the phrase as a cop out, but it's true. It depends because it's what's sounds best to you. Have you looked in your owners manual for the manufacturer crossover recommendation?

@coachvelarde

Жыл бұрын

I have and I used Audyssey for the calibration. Thanks

@coachvelarde

Жыл бұрын

Did the calibration again and here are the results. Should I change anything? Front- 40hz Center- 40hz Surround- 60 hz Front Dolby- 90hz

@MovieUniversity

Жыл бұрын

@@coachvelarde Those numbers seem a little low to me. Mess around with them and consistently use the same song, movie or what have you when tweaking. Keep releasing to the same sounds and see what frequencies sound best. At the end of the day it's about what sound good to you. The rest of us aren't in your house judging the numbers you have for your crossovers.

I set my tower 6 0hm yamaha speakers that go down to 30hz to 60htz my yamaha center channel goes down to 50htz I set that to 70htz and my yamaha surround sound speakers that go down to 60htz to 80htz. My yamaha atmos go down to 60hz set to 80 hz Both klipsch Subwoofers at 120 and it all sounds incredible...

What is that subwoofer at the 2:38 mark? That is a beast!

What’s the best crossover frequency for speakers which are rated 1500Hz, 200-1400Hz, 120-1500Hz ?

@MovieUniversity

Жыл бұрын

The lowest number

Calibration the way to calibrate spl meter or auto calibration

The real question I have is if say you set the cross over to 40 on your front left and right speakers. Do I then set the crossover on the actual sub to 40 too?

@andyb4050

21 күн бұрын

No. The sub frequency should be turned up to max. Let the receiver/ processor do the crossing over

my center speaker is Dali Opticon Vokal MK2 the frequency response is 47-30 wich frequency response you recomend, thank you for the attention

@MovieUniversity

Жыл бұрын

47

@josedesouzajunior6688

Жыл бұрын

@Movie University thank you , I will keep 47

Awesome video bro!! I have a Sony STR HD790 and I still can’t figure it out how to calibrate the levels with my spl specially cause it don’t have the volume scale to set it up at 75 to 80 And when I start calibrating the levels I put my receiver at 0 on the master volume and I don’t get any sound I’ll really appreciate it if you can help me thank you?

@mivanp2185

Жыл бұрын

Did you figure it out ? Ive got some tips to help you otherwise

@josephpicado1818

Жыл бұрын

@@mivanp2185 no I couldn’t figure it out 😞

@mivanp2185

Жыл бұрын

@@josephpicado1818 Its just a different scale. So start with your test tone in your receiver . Start F/L and turn your volume to as high as it reads 75db on your spl meter. Then do all your channels the same by adjusting via the speaker level setting for each channel so that they are all reading 75db at the same overall volume level

@mivanp2185

Жыл бұрын

@@josephpicado1818 I have the similar model. Just bought some new fronts so having to do a full calibration again and came across your comment

@josephpicado1818

Жыл бұрын

@@mivanp2185 thank you so much so this avr goes from 0 to 100 on the volume so turn it all the way up to a 100?

when he say look at the speaker manual does that mean where it say RATED FREQUENCY RANGE (HZ) 35hz-50hz?

@MovieUniversity

5 ай бұрын

Yes

Hmm struggling to find where to set my focal aria 926 towers and 900c centre. Any help

@dsellars

2 жыл бұрын

I’ve got the same speakers. I’m interested to hear what you set them at an how you find them

@MovieUniversity

Жыл бұрын

The 80Hz that THX puts out is a baseline that nearly every speaker can go to. However, to get the optimal output look up the specs for your particular speakers on the manufacturers website. For instance, my Klipsch right and lefts are both set to 60Hz because that is what Klipsch recommends.

@danboy3818

Жыл бұрын

I just get a klipsch rp-504c, its set at 60hz and its not as clear as i was expecting... not sure what to set in some scenes, i can ear background noise

@MovieUniversity

Жыл бұрын

@@danboy3818 could you retype that last night please. i don't understand the question.

I am new to this AVRs n all. Last week i got my Denon X1700H & klipsch refernce R series 5.1. Works great as its a starter set up. I set my subwoofer in 80hz. Inside Avr set into LFE. The default inside value is 120hz. Which one should i go for ? 80 for both or 120 ???

@MovieUniversity

Жыл бұрын

Go to 80

@purenstinctxi

7 ай бұрын

What settings do you have on the reciever? I have the same and Iam a newbie. Do I need to change this cross over stuff defying on my AVR. ? I have subwoofer 1200sw

Ok so what if I just have a knob to adjust crossover and it doesn’t say how many hertz?

@MovieUniversity

Жыл бұрын

Is there any kind of number on it at all? If no indicator then you'll have to keep playing with it til you get what sounds best to you.

I have R25C, R15M Front, and R41M for surround. Let me know if I understand you correctly. R25C: 120hz R41M: 150hz R15M: 90hz I guess??? The sub is R-100sw, I think 60hz? 70hz? 80hz?

@MovieUniversity

Жыл бұрын

The Klipsh manual should tell you what is the best frequencies.

I have Bose AM-5 series 1 speakers, I need to setup the crossovers for my cube speakers that have no woofer….anyone have any thoughts

@MovieUniversity

Жыл бұрын

Have you looked at the owners manual for the appropriate frequencies?

@michaeltobler649

Жыл бұрын

@@MovieUniversity Thanks so much for you response. I found this in the owner’s manual: 2 6” low frequency drivers, and 4 magnetically shielded wide range drivers in cube speaker arrays. I know the industry standard is 80hz…So should I raise my crossover to 100-120hz?

My focal sopra n2 what crossover I can set my processer

@MovieUniversity

Жыл бұрын

you need to look up the owners manual online.

@zubedaakthar6126

Жыл бұрын

@@MovieUniversitydear sir my. Focal sopra n2 frequency response (33)dB 34Hz-40khz low frequency point (-6dB) 28Hz what crossover I can set my processer and small or large thank you for cooperation

@zubedaakthar6126

Жыл бұрын

Thank you

Yamaha HTR 3072 AVR FS & CS - NS-P 350 SS - VX S 5 SURFACE MOUNT SW - NS - SW 300 ROOM AREA - 130 SQFEET ALL YAMAHA PRODUCTS Using abv system pl suggest crossover

@MovieUniversity

Жыл бұрын

Very nice 😎

Where can I find the video on “tips on how to best show off your system” please? Found it: kzread.info/dash/bejne/aalq14-OgrDAdc4.html

40 hz is best

set em all at 80 and call it a day

Whatever happened to Woofers? Just. Woofers. Not everything is a “sub woofer.”

@MovieUniversity

5 ай бұрын

nearly every base playback device for home theaters is a subwoofer.

@jukesjointOG

5 ай бұрын

@@MovieUniversity “Bass.”

@MovieUniversity

5 ай бұрын

@@jukesjointOG yeah yeah, autocorrect, what can i say.

@jukesjointOG

5 ай бұрын

@@MovieUniversity If Autocorrect was a person, I’d already be in jail for murder.