The body was so clean on that thing, too bad the engine was seized up. Great vid Louie, keep 'em coming !!

Hey Louie! You need to put together a playlist of all things 3 wheeler! Thanks ahead of time!!

@kriticalbuilds3232

3 жыл бұрын

El fin te rrv

never hammer a screwdriver between gasket faces 😲😲😲🤤🤤

@henrypauley4877

Жыл бұрын

This dude is rough

Sucks sinking money into a project like that. But you're bringing an artifact back to life

Blows my mind that you can replace the head/pistons for less than the pulse generator+parts if its missing. Really if people looked after these motors better they would never die, just like the honda commercial motors

You got lucky as hell with that bolt!

i learned this trick with old chev halfton differentials..if ya turn off your stick welder hook up the ground of course and slide a rod down into the middle of the broken off bolt ..have a buddie or reach and flip your power on and off really quick.the rod will quickly tack itself to the bolt ..usually a 7018 will stick right to the bolt and it will turn right out ...not if its tight but it works really awesome sometimes in a pinch ...love these old wheelers i got a 250es myself ...most fun i've had

I would love if you guys did a front sprocket change video on the Atc200e ! Seems like alot to take apart

Thanks alot bud this really help my issue ..

did this motor get fixed ? can't find a video on it,,or a part 2....

Thanks for another good 1

I know the cylinder looks bad but that one looks usable. I guess my motto is try it if it works great if not your going to have to rebuild it anyways. I have unstuck probably a half dozen engines all the same way. Most of the time you dont have to dive into it and take it apart. The guy had a some what idea of what to do but ask any car guy about unseizing an engine it all starts with Marvs Mystery Oil. Ive even heard of Jay Leno using this trick. Ive only had one that I had to take apart but I was going to upgrade the heads anyways and that was on an 4.3 v6. I really didnt even try to get it unstuck I just took the heads off and poured the Oil right in. And trust me The cylinders looked Awful one was full of water. Way worst then that cylinder. I used a scotch brite pad dipped in mystery oil on the bad cylinders to kind of etch and clean the bad rust spots. The funny thing is the one with the worst rust has the highest compression 160 all the rest are around 150. Ok so this is what you do you pour the mystery oil down the cylinder through the spark plug and let it sit. may be over night. then you get a breaker bar with a socket or even by hand Ive done it and and you wiggle the crank back and forth. even if it doesnt budge it wil eventually free you might have to pour more in or even heat the cylinder a little and the oil but it will free up. after its unseized drain oil and all the fluids and replace spark plug etc. Know its time to start and when it first does its going to smoke like an S.O.B. it has to burn of that oil but it should go away eventually. Break it in slowly and when you feel comfortable run the piss out of it to clean out that carbon. Lastly I know this works I had an old Motorcycle I parked outside during the winter got moisture in the cylinders. I tried everything on it even brought it to the dealer thinking that it was the starter. They where like nope its seized you have to rebuild it. My buddy taught me this trick. It took one knight and I hit the starter and it unseized bingo bango. Saved me thousands and I have driven that bike probable 10,000 miles since no problems no smoking etc. runs great hope this helps!

@Vfh........y

7 жыл бұрын

stubby2871 ...smart......old school smart.

@gregorycarter6148

5 жыл бұрын

I saw your reply on this video, do you have any advice for a siezed 400 cc Honda rancher four wheelers engine. Please contact me, my email is dad1012928@yahoo.com, or by phone! text if you prefer. 423-618-6605, my name is Michael. Thank you and God bless

Take the two 24mm hex valve lifter adjustment covers off valve cover out watch for oil to top end if none replace the oil pump like I said ealier or it goes screech and seized up quick bye bye new piston and cam

Cool idea to remove the broken bolt, im going to have to try that on a lawn mower i broke a bolt off in. Our 200es had a flooding out carb and along with some nice yellow puke looking oil. The PO also put the timing chain on wrong and it would try and rip your arm off if you pulled it over. When I took the engine apart they must have recently rebuilt it, and it runs amazing in comparison to our worn out 200e. Gotta love getting stuff cheap it was assembled incorrectly, or taken care of poorly.

Awesome video thanks

Link to follow up completion video?? Also, your table wobbling was making me nervous.

Anyone notice him say drink a beer around 7:01-7:03 lol

@erikcreamer4762

7 жыл бұрын

Lol. I just went to that time and listened to it, that had me laughing hard, need to drink a beer lol

@overthehillsandfaraway7411

5 жыл бұрын

Subliminal messaging I was wondering why I felt like I wanted one

Do you need to get a new cylinder and piston to get it unseize or just clean all the parts you did?

I think you might able to hone the cylinder at just bore it over by a little bit and then get new piston and rings

Can you show how to fix the neutral light inside theengine

Thanks for making video

Great job.

@PowerModzOfficial

3 жыл бұрын

Thanks!

Do you have a link for putting this engine back together?

How do I remove the sub transmission cover on a 200 es

Just seized mine today after running on no oil. Just put some mystery oil in the spark plug hole and filled the oil. Good to go after a handful of turns. CANT KILL A THREE WHEELER

Cool ! Now you ya know ,lucky no bent valves . Piston, rings,pin&bearing , & boar out to next size,& engine flush ....that thig should be smok'n again ...well not really smoking ,should be good to go. Thumbs up Louie!

Know anything about the older 350s? Might buy up one that's seized but buddy says it was probably a bent valve from jumping timing, apparently a common issue?

How do i unsized a polaris storm 800cc snowmobile trippel ??

You're a maniac and i love it. Keep up the good work

New crank/bearings, new piston/cylinder

If that bolt was not broke could you have removed that left cover without removing the bolt. Is that bolt reverse thread. I have a small oil leak and want to pull that cover and replace the gasket but it will not come off . I have not removed the bolt.

....I like he is on some type of stimulant or something....way to fired up.

hi, love your vids, I have a atc200 with the return springs broken, on the spark advance.... whats the easyiest way to get that off so i can put a new one in. the bike usually starts first time, but always fouling plugs.

@TheJessicarabbit09

7 жыл бұрын

pulse coil is still hooked in the harness, dont really wanna be unhooking and fooling around with that, if i dont have too. Ive marked the coil with marker lines on the base, to try to put it back in the exact same spot. but the screws are starting to strip. I stopped b4 actually stripping them. can i just take whole base off ( which everything still hooked up) ?

Does the big red and the 200m share the same engine ?

Thank you sooooooo much for posting these videos! After watching this, I have such a better understanding on what to expect when I dig into my 82. I have a question though, my big red never came with a high/low range lever to switch between the two. So to make due, I screwed in a screw with a nail welded on the top as acting as the lever. It switches smoothly into each range, but the problem I'm having is that it doesn't lock in, it's free to move in and out as it pleases. Do you have any advice as to what to do?

@duckworthatvandmxadventure6601

2 жыл бұрын

There should be a screw with a spring and detent try checking that

Will a 300fw topend work on that 200e?

Why the hell would you use a screwdriver and a hammer to pull the side cover first? WTF dude.

@mathuflores8235

5 жыл бұрын

My exact thoughts. Dude is gonna fuck up the case by doing that. Alla you need is a mallet some love taps around and Voilà

@ildxnnyli5541

5 жыл бұрын

Mason Wengeler he hasn’t mastered engines

I think you did good on video and work I don't see any of these other guys talking shit about what you did wrong have a shop and filming videos. So keep it up I learned something cause I'm honest I don't shit about ATC engines

I need help with my 1986 230 Suzuki quad sport

Did you ever do q video on rebuilding it

3:20 dat face tho lol Louis was mad....

Did you not put this motor together again

Just bought my first 3 wheeler would be fun to ride together sometime

Louis try muriatic acid! It will remove the rust but ! The rust would have probably damage the cyl wall!

Pro tip: Quit using your palm for a hammer.

can you please tell me how to adjust a 1984 HONDA ATC 200S air and fuel mix on a carburetor thanks

@swift-horse2242

5 жыл бұрын

Samuel Chirilenco there’s a video on how to do that you just have to look for it

bet someone left the spark plug out

Impact wrench @ 3:17

For the time it takes do and valve stem seals and check your oil pump before you put it all together thing will last another 50 years if you don't swAmp it in a lake again or river and leave it full of water

I have never seen mechanics that know what they're doing throw everything inside a pile. Everything's usually laid out in order Even all the bolts. Why would anyone Want to figure out where each bolt goes. Just lay them out in order. With each part you take off. Gee, whiz!

@stevewilliams2725

2 жыл бұрын

Exactly, as a professional tech I lay parts in order and put in separate containers, packages etc.. I also shake my head when everything tossed on floor or in a pile.

@PowerModzOfficial

2 жыл бұрын

lol ya, im a piler.

Can you repair the engine of my 1985 250ES?....I will be happy to mail it you...thanks...it turns, but only 180 degrees each way

sweet

I wonder if those clutch plates are going to be ok after soaking in gas. I've seen gas flooded engines where the cutch is shot after soaking for a while.

@PowerModzOfficial

10 жыл бұрын

Good question -I guess I'll find out!

@ybnlean7819

8 жыл бұрын

How did you get good at motors? childhood experience?

"not a big fan of over boring".....credibility gone.

how come you didnt say what year /size of engine? was it the 200 cc chain drive non reverse big red or the 2oocc with shaft /reverse or the venerable 250 shaft /reverse model?

@tsrolley

6 жыл бұрын

Darrren Betker you can tell by the sub trans that this is a 200es big red. They are shaft drive with reverse. Most likely it is an 84 model because that seems to be the most common year for 200es and the year most 200es's were made.

Dont jump on me for this suggestion, but why couldnt he just clean up the piston with some gasoline, using a toothbrush and clean up the cylinder walls with some emery cloth and or some steel wool?

2:55 made me cringe.. that is NOT how you seperate a case! Us3 a rubber mallot and tap around the caseing. Wedging an aluminum case normally will crack it or gouge the mating surface. 😮

How this motor advance spark because it have cdi unit or governer advance Nowadays cdi motorcycle doesn't have governer only they have cdi unit wich advance the spark so how xl or xr 185 or 200 advance the spark

Hey I bought a 200 big red that starts first pull everytime, I can drive it ver slow or let it idle until I have no gas left in the tank. it is leaking oil from the head. But if I drive it fast it overheats it only a matter of minutes. any idea of what the issue could be?

@ybnlean7819

8 жыл бұрын

i had that happen too. not the overheat, but the head leaks oil, and all mine drained out. so i think it leaks out, and overheats

the bike moves freely in gear . i put oil in it while it was hot and every since then it will not go in gear or move after i kick start it and try to take off it just free roll... its 1983 honda 200x three wheeler

nice :)

Hey Louis, I was wondering how to fix an out of time 340 arctic cat ( sled) the valves are not where they're supposed to be when the piston comes up. How can I fix this?

@hondacicle

10 жыл бұрын

in order to do that to a cat motor you need a. muffler stretcher. and a bearing stretcher. also a left handed screwdriver. but sorry i can't tell you how to use those tools lol :) ps you got to watch those cats the valve timing seems to change by itself seems to be more around mid November just a tip

@PowerModzOfficial

10 жыл бұрын

Ball bearings, some gauze and some forty weight oil - just ask geometry fletch.

is it possible to have a bike that is seized and still kicks over?

@PowerModzOfficial

3 жыл бұрын

no

Quick question. Why aren't you a fan of boring? Thanks and nice video

I always find it hilarious when people comment on how shotty of job someone's doing and that there masters of the trade yet they watch how to videos and regurgitate b.s. if you don't like how one guy gets the job done go watch the other guy or make your own video...sometimes yah need a hammer and sometimes yah need a beer.....

@PowerModzOfficial

5 жыл бұрын

I like the way you said that.

@michaelmacdonald1252

5 жыл бұрын

I had to pound out the piston on xl200 today Sam issue as the video only I did not try to force, in the process of slammin that little bastard out I ended up cracking the bottom of the barrel. She was in there good, so my 30 dollar question is can I replace the cylinder wall or should I bite the bullet and get a new bored out top end (300 bucks)

Is that a slight irish accent i hear?

You said you're not a big fan of overboring...please elaborate...I'd bore it over..

Excellent Trouble Shooting. 5/18/2021

I bet some EVAPO RUST and a quick hone would bring that cylinder back.

Anyone know where the best place engine parts for a Honda atc 1982 200s?

@waynebrady5585

3 жыл бұрын

Best parts will always be OEM replacement parts. Look up the part numbers and search them on Ebay.

hi sir, could you check my 18 sec video and tell me if my engine is seize or else plz i am soo lost and only use my quad 1 time.

split the cases louie

It's easier to get the cam out if you take the rocker cover off lol, and I'd just overbore it, just .010 or .020 over, just the minimum needed.

@PowerModzOfficial

10 жыл бұрын

you think? it comes out pretty easy this way - and it's what the manual recommends for changing the cam. i'll have it looked at, the pitting seems deep but hopefully it can be done.

@Gearheadtom

10 жыл бұрын

Guess I never tried that way, just assumed it was harder haha.

@PowerModzOfficial

10 жыл бұрын

Gearheadtom nope pretty darn easy - and you don't need to replace the gasket:) unless the whole thing gets torn down I guess.

@Gearheadtom

10 жыл бұрын

PowerModz That's not a big issue anyway, the rocker cover doesn't use a gasket, just sealer, but I'll try that next 185/200 I'm into.

@PowerModzOfficial

10 жыл бұрын

Gearheadtom oh ya - i forgot that - just did it last week:) Tired here.

Did these early Big Reds Have reverse? I cant remember. She will run again!!! I wanna know where your finding these.lol

@PowerModzOfficial

10 жыл бұрын

not this one, hi and low only, gotta look hard!

@donaldfuller6617

10 жыл бұрын

PowerModz Theres been a few of the 250 Big Heads on the Vt craigslist recently not to bad a ride from the Ottawa area.

Search tommartyn on you tube the guy knows everything about honda 3 wheelers and what fits what. Dudes got like 20 mostly running trikes.

im guessing the 250 head wont fit on there? or just find the newer 250 motor...

@PowerModzOfficial

10 жыл бұрын

its a 200, ill bring it in to get bored - see if it can take it.

@TheCuttingtorch

10 жыл бұрын

PowerModz right, it would be cool if the newer 250 head from the '85 big red would just slide on but probly not

This engine has never had an oil change in its life and they get hot where it air cooled and oil will get sludge after a month of riding hard in hills where no air flow is as much but don’t work on them if you don’t know how I am going on 20 years building different engines cars and atv and water cooled atvs

Flood damaged motor

Dude wears gloves and shaves his arms 😂😂😂😂

Hone the cylinder.

Dude, you dont see the tabs on the case to break the seal? My man, easy! What is this your first rodeo?

@doctordirk6316

3 жыл бұрын

This guy's rough and in a hurry!

gloves are for guys who don't wanna get dirty

@PowerModzOfficial

8 жыл бұрын

Gloves are for guys who don't want to get cancer and want to live a long healthy life with their family. Ive been exposed to many things over the years - time to wear gloves.

@drewyoder6027

8 жыл бұрын

+PowerModz I respect that and understand it. I wanted to see if I could get a reply out if you. in all seriousness, gloves and safety glasses are are must. especially when working with engines and oil and other fluids and chemicals.

Tragedy

Blame Canada

Work on a 350x honda I'm about to rebuild one I need to learn some stuff

@fmm1979

6 жыл бұрын

Jarret Quarles what you need to rebuild a 350x is a lot of money

What a flog he even promotes Evans coolant

That’s not a Honda big red moter

Lol Canadian accent

yikes! as soon as i saw this guy screw driver the casing off I stopped watching

@PowerModzOfficial

3 жыл бұрын

Oh no!!!

Please stop

Hone the cylinder oil it take rings put in oil clean piston clean the rings put her back toghter old Honda engines are the best I have a 91 model 300 four Trax just change oil and spark plug regular can’t kill those engines but keep timing chain with in spec don’t want to hear it to loose

@gregorycarter6148

5 жыл бұрын

If you get this, it seems you know what your talking about, I had my Honda rancher 400cc four wheeler sieze up today, for lack of oil. The guy who gave it to me yesterday told me it burned oil but I am ignorant and didn't think to check it this afternoon. Do you have any advice to keep me from having to but another engine. Please call or text (423) 618-6605, or if you would like you can email me dad1012928@yahoo.com thanks and God bless

I'd recommend you stick to our day job.

Who showed this guy how to pull a case off a bike engine

He clearly making shit up lol